国内外压力标准
pressure standards
美国压力标准(ANSI pressure standards)
--------------------------------------------------------------------------------
编号 中文名称 英文名称
ANSI A161.2-1998 人造高压力加工的装饰性案台面板的性能标准 Decorative
Laminate Countertops, Performance Standards
for Fabricated High Pressure
ANSI B11.1-2001 机床.机械动力压力机.制造、维护和使用的安全要求 Machine
Tools - Mechanical Power Presses - Safety Requirements
for Construction, Care, and Use
ANSI B11.16-2003 粉末/金属压力机的安全要求 Safety Requirements
for Powder / Metal Compacting Presses
ANSI B16.18-2001 铸铜合金焊锡连接压力配件 Cast Copper Alloy
Solder Joint Pressure Fittings
ANSI B5.52M-1980 开式通用单点机械压力机(米制) Presses, General
Purpose, Single Point, Gap Type, Mechanical
Power (Metric)
ANSI S1.15 Part 2-2005 测试传声器.第2部分:用互易技术对实验室标准传声器进行压力校准的主要方法
Measurement Microphones - Part 2: Primary Method
for Pressue Calibration of Laboratory Standard
Microphones by the Reciprocity Technique
ANSI Z21.18-2007 燃气器具压力调节器(与CSA 6.3相同) Gas Appliance
Pressure Regulators (same as CSA 6.3)
ANSI Z21.80-2002 线性压力调节器(同CSA 6.22) Line Pressure
Regulators (same as CSA 6.22)
ANSI Z21.80a-2005 管路压力调节器 Line Pressure Regulators
(Same as CSA 6.22a)
ANSI/(NFPA) T2.12.1-2002 液压传动.系统和产品.测量平均稳态压力的方法
Hydraulic fluid power - Systems and products
- Method of measuring average steady-state pressure
(to be used in conjunction with ANSI/(NFPA)T2.12.10)
ANSI/AAMI NS28-1988 颅内压力监测装置 Intracranial Pressure
Monitoring Devices
ANSI/AIAA S-080-1998 航天系统.金属压力容器、加压结构和压力构件 Space
Systems - Metallic Pressure Vessels, Pressurized
Structures, and Pressure Components
ANSI/AIAA S-081A-2006 航天系统.复合包装压力容器(COPV) Space
Systems - Composite Overwrapped Pressure Vessels
(COPV)
ANSI/API 510-2006 压力容器检验规程:维护、检测、鉴定、修理和更换 Pressure
Vessel Inspection Code - Maintenance Inspection,
Rating, Repair, and Alteration
ANSI/API 521-2006 石油、石化产品和天然气工业.压力泄放系统 Petroleum,
Petrochemical, and Natural Gas Industries -
Pressure Relieving and Depressuring Systems
(ISO 23251)
ANSI/API 572-2001 压力容器检查 Inspection of Pressure
Vessels
ANSI/API 576-2000 压力释放设备检查 Inspection of Pressure-Relieving
Devices
ANSI/API RP10B-4-2004 大气压力下泡沫水泥浆的制备和试验的推荐规程
Recommended Practice on Preparation and Testing
of Foamed Cement Slurries at Atmospheric Pressure
ANSI/API RP10B-5-2007 大气压力下固井水泥加工制剂的收缩和膨胀测定用推荐实施规程
Recommended Practice on Determination of Shrinkage
and Expansion of Well Cement Formulations at
Atmospheric Pressure
ANSI/ARI 770-1994 制冷压力调节阀 Refrigerant Pressure
Regulating Valves
ANSI/ASAE S385.5-1993 联合收割机轮胎荷载和充气压力 Combine
Harvester Tire Loading and Inflation Pressures
ANSI/ASAE S430.1-1996 农用设备轮胎的负载和膨胀压力 Agricultural
Equipment Tire Loading and Inflation Pressures
ANSI/ASHRAE 158.2P-2006 制冷剂压力调节器试验功能方法 Methods
of Testing Capacity of Refrigerant Pressure
Regulators
ANSI/ASME A112.19.15-2005 带压力密封门的浴池/旋涡浴池 Bathtub/Whirlpool
Bathtubs with Pressure Sealed Doors
ANSI/ASME B16.22-2001 锻铜和铜合金钎焊接压力连接件 Wrought
Copper and Copper Alloy Solder-Joint Pressure
Fittings
ANSI/ASME B16.38-1985 气分配系统用大型手动金属阀(NPS 2 1/2到12,最大压力为125psig)
Large Metallic Valves for Gas Distribution (Manually
Operated, NPS 2 1/2 to 12, 125 psig Maximum)
ANSI/ASME B16.44-2002 压力不超过5psi的地上管道系统中用手工操作的金属气体阀门
Manually Operated Metallic Gas Valves for Use
in Aboveground Piping Systems up to 5 psi
ANSI/ASME B31.9-2004 建筑物服务设施用压力管道标准 Building
Services Piping Code for Pressure Piping
ANSI/ASME B40.1-1991 量规.压力显示刻度表型.弹性元件 Gauges
- Pressure Indicating Dial Type - Elastic Element
ANSI/ASME B40.100-2005 压力计和压力计附件 Pressure Gauges
and Gauge Attachments
ANSI/ASME B40.6-2001 压力限幅电子管 Pressure Limiter
Valves
ANSI/ASME B5.49-1998 机械压力机术语、汇编 Press Terms,
Glossary of Mechanical
ANSI/ASME B5.55M-1994 机动压力机制动装置规范和性能标准 Specification
and Performance Standard, Power Press Brakes
ANSI/ASME B5.61-2003 通用单动直边式动力压力机 Power Presses
- General Purpose Single Action Straight Side
Type
ANSI/ASME BPVCEdition-2001 ASME锅炉和压力容器编码 ASME
Boiler and Pressure Vessel Code
ANSI/ASME BPVCRevision-2007 ASME锅炉和压力容器代码(2/2/07会议)
ASME Boiler and Pressure Vessel Code (2/2/07
Meeting)
ANSI/ASME HPS-2003 高压力系统 High Pressure Systems
ANSI/ASME MFC-8M-2001 密封管中流体流量.主要设备和次要设备间压力信号传输用连接件
Fluid Flow in Closed Conduits - Connections
for Pressure Signal Transmission Between Primary
and Secondary Devices
ANSI/ASME PCC-1-2005 压力限制螺栓连接法兰联轴节组件的导则 Guidelines
for Pressure Boundary Bolted Flange Joint Assembly
ANSI/ASME PCC-2-2006 压力设备和管道的维修标准 Repair of
Pressure Equipment and Piping Standard
ANSI/ASME PTC19.2-2004 压力测量仪器仪表.第2部分 Pressure
Measurement Instruments and Apparatus - Part
2
ANSI/ASME PVHO-1-2007 人占用的压力容器的安全标准 Safety Standard
for Pressure Vessels for Human Occupancy
ANSI/ASME PVHO-2-2003 压力容器的安全性标准.在有人占用PVHO丙烯酸窗口时容器的安全使用指南
Safety Standard for Pressure Vessel for Human
Occupancy In-Service Guidelines for PVHO Acrylic
Windows
ANSI/ASSE 1020-2004 压力真空断路器组件 Pressure Vacuum
Breakers Assembly
ANSI/ASTM A20/A 20M-2001 压力容器钢板一般要求规范 Specification
for General Requirements for Steel Plates for
Pressure Vessels
ANSI/ASTM A299-1996 压力容器用锰硅碳钢板规范 Specification
for Pressure Vessel Plates, Carbon Steel, Manganese-Silicon
ANSI/ASTM A703/A 703M-2001 压力容器部件用钢铸件一般要求规范
Specification for Steel Castings, General Requirements,
for Pressure-Containing Parts
ANSI/ASTM B834-1996 压力强化粉末冶金铁镍铬钼和镍铬钼钶(Nb)合金管法兰、管配件、阀门和零件规范
Specification for Pressure Consolidated Powder
Metallurgy Iron-Nickel-Chromium-Molybdenum (UNS
N08367) and Nickel-Chromium-Molybdenum-Columbium
(Nb) (UNS N06625) Alloy Pipe Flanges, Fittings,
Valves and Parts
ANSI/ASTM D1267-2002 计量液化石油(LP)气蒸气压力的试验方法(液化石油气法)
Test Method for Gage Vapor Pressure of Liquefied
Petroleum (LP) Gases LP-gas Method
ANSI/ASTM D1599-1999 塑料管材、管道和管件短时液压故障压力试验方法
Test Method for Short-Time Hydraulic Failure
Pressure of Plastic Pipe, Tubing, and Fittings
ANSI/ASTM D1621-2000 泡沫硬质塑料压力特性试验方法(08.01) Test
Method for Compressive Properties of Rigid Cellular
Plastics (08.01)
ANSI/ASTM D1657-2002 用压力温差比重计测定轻质烃密度或相对密度的试验方法
Test Method for Density or Relative Density
of Light Hydrocarbons by Pressure Thermohydrometer
ANSI/ASTM D1760-2001 木材产品压力处理规范 Specification
for Pressure Treatment of Timber Products
ANSI/ASTM D2143-2000 增强热固塑料管循环压力强度试验方法(08.04)
Test Method for Cyclic Pressure Strength of
Reinforced, Thermosetting Plastic Pipe
ANSI/ASTM D2241-2005 聚氯乙烯(PVC)额定压力管规范(SDR系列)
Specification for Poly(Vinyl Chloride) (PVC)
Pressure-Rated Pipe (SDR Series)
ANSI/ASTM D2484-2006 聚酯薄膜压力敏感的电绝缘胶带用规范 Specification
for Polyester Film Pressure-Sensitive Electrical
Insulating Tape
ANSI/ASTM D2503-1992 用蒸气压力的热电测量法测定烃类分子重量的试验方法(05.01)
Molecular Weight of Hydrocarbons by Thermoelectric
Measurement of Vapor Pressure, Method of Test
for (05.01)
ANSI/ASTM D2513a-2007 热塑性燃气压力管及配件的规范 Specification
for Thermoplastic Gas Pressure Pipe Tubing and
Fittings
ANSI/ASTM D2774-2001 热塑压力管地下安装惯例 Practice for
Underground Installation of Thermoplastic Pressure
Piping
ANSI/ASTM D2782-2002 润滑流体耐极端压力特性的测量方法(泰姆肯试验方法)(05.02)
Measurement of Extreme-Pressure Properties of
Lubricating Fluids (Timken Method), Method for
(05.02)
ANSI/ASTM D2878-1995 评估润滑油的表观蒸气压力和分子重量的方法(05.02)
Method for Estimating Apparent Vapor Pressures
and Molecular Weight of Lubricating Oils (05.02)
ANSI/ASTM D2879-1997 用液体蒸气压力计测定液体的蒸气压力-温度关系和初始分解温度的试验方法
Test Method for Vapor Pressure-temperature Relationship
and Initial Decomposition Temperature of Liquids
by Isoteniscope
ANSI/ASTM D2889-1995 石油馏出燃料的实际蒸气压力的计算(05.02)
Vapor Pressures of Petroleum Distillate Fuels,
Calculation of True (05.02)
ANSI/ASTM D2924-2001 增强热固性树脂管耐外部压力试验(08.04)
Reinforced Thermosetting-Resin Pipe, Test Method
for External Pressure Resistance of (08.04)
ANSI/ASTM D2990-2001 塑料的张力、压力和柔性蠕变以及蠕变断裂试验方法(08.02)
Test Methods for Tensile, Compressive, and Flexural
Creep and Creep-Rupture of Plastics (08.02)
ANSI/ASTM D2992-2006 玻璃纤维(增强玻璃纤维的热固树脂)管和配件用获得静液压或压力设计基础的规范
Practice for Obtaining Hydrostatic or Pressure
Design Basis for "Fiberglass" (Glass-Fiber-Reinforced
Thermosetting-Resin) Pipe and Fittings
ANSI/ASTM D3139a-1996 使用柔韧弹性体密封的塑料压力管接头规范 Specification
for Joints for Plastic Pressure Pipes Using
Flexible Elastomeric Seals
ANSI/ASTM D323-2006 石油产品的蒸气压力的试验方法(Reid法) Test
Method for Vapor Pressure of Petroleum Products
(Reid Method)
ANSI/ASTM D3233-1993 液体润滑剂的极端压力特性的测量方法(润滑剂耐热耐压法)(05.02)
Measurement of Extreme Pressure Properties of
Fluid Lubricants (Falex Methods), Methods for
(05.02)
ANSI/ASTM D3291-1997 压力作用下聚氯乙烯塑料增塑剂兼容性惯例 Practice
for Compatibility of Plasticizers in Poly(Vinyl
Chloride) Plastics under Compression (08.03)
ANSI/ASTM D3517-2006 玻璃纤维增强热固性树脂压力管的规范 Specification
for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin)
Pressure Pipe
ANSI/ASTM D3754-2006 玻璃纤维增强热固性树脂污水压力管和工业压力管的规范
Specification for Fiberglass (Glass-Fiber-Reinforced
Thermosetting-Resin) Sewer and Industrial Pressure
Pipe
ANSI/ASTM D4953-2006 汽油和汽油氧化混合物的蒸汽压力试验方法(烘干法)
Test Method for Vapor Pressure of Gasoline and
Gasoline-Oxygenate Blends (Dry Method)
ANSI/ASTM D5190-2001 石油产品蒸气压力测试方法(自动法) Test
Method for Vapor Pressure of Petroleum Products
(Automatic Method) (05.03)
ANSI/ASTM D5191-2007 石油产品蒸气压力的试验方法(小型法) Test
Method for Vapor Pressure of Petroleum Products
(Mini Method)
ANSI/ASTM D5482-2001 石油产品蒸气压力试验方法(最低大气法) Test
Method for Vapor Pressure of Petroleum Products
(Mini Method-Atmospheric)
ANSI/ASTM D5483-2005 利用压力差示扫描量热法测定润滑油脂氧化诱导时间的试验方法
Test Method for Oxidation Induction Time of
Lubricating Greases by Pressure Differential
Scanning Calorimetry
ANSI/ASTM D5949-2001 石油产品倾点测试方法(自动压力脉冲法) Test
Method for Pour Point of Petroleum Products
(Automatic Pressure Pulsing Method)
ANSI/ASTM D6186-1997 利用压力差示扫描量热法(PDSC)测定润滑油氧化诱导时间定测定方法
Test Method for Oxidation Induction Time of
Lubricating Oils by Pressure Differential Scanning
Calorimetry (PDSC)
ANSI/ASTM D6377-2004 原油蒸气压力测定的试验方法:Vpcrx(膨胀法)
Test Method for Vapor Pressure of Crude Oil:
Vpcrx (Expansion Method)
ANSI/ASTM D6378-2007 测定石油产品、碳氢化合物和氧化烃类混合物的蒸气压力(Vpx)的试验方法(三胀法)
Test Method for Determination of Vapor Pressure
(VPx) of Petroleum Products, Hydrocarbons, and
Hydrocarbon-Oxygenate Mixtures (Triple Expansion
Method)
ANSI/ASTM D6749-2002 石油产品倾点测试方法(自动空气压力法) Test
Method for Pour Point of Petroleum Products
(Automatic Air Pressure Method)
ANSI/ASTM D6897-2004 液化石油气(LPG)蒸气压力的试验方法(膨胀法)
Test Method for Vapor Pressure of Liquefied
Petroleum Gases (LPG) (Expansion Method)
ANSI/ASTM D7344-2007 大气压力下石油产品的蒸馏用试验方法(小型法)
Test Method for Distillation of Petroleum Products
at Atmospheric Pressure (mini Method)
ANSI/ASTM E1008-1997 地热和其他高温压力设备用阀身压力释放装置的装配、检测和维护惯例
Practice for Installation, Inspection, and Maintenance
of Value Body Pressure Relief Methods for Geothermal
and Other High-Temperature Applications
ANSI/ASTM E1424-1991 在试验样件规定压力和温差下测定通过外窗、幕墙和门空气泄漏率的试验方法
Test Method for Determining the Rate of Air
Leakage Through Exterior Windows, Curtain Walls,
and Doors Under Specified Pressure and Temperature
Differences Across the Specimen (04.11)
ANSI/ASTM E1597-1999 海洋环境用光伏电池模拟器盐水浸没压力和温度测试方法
Test Method for Saltwater Pressure Immersion
and Temperature Testing of Photovoltaic Modules
for Marine Environments
ANSI/ASTM F1041-1995 聚烯烃燃气压力管和配件挤压指南 Guide for
Squeeze-Off of Polyolefin Gas Pressure Pipe
and Fittings
ANSI/ASTM F1176-2001 最大工作压力为63psi(磅/平方英寸)的热塑灌溉系统设计和安装惯例
Practice for Design and Installation of Thermoplastic
Irrigation Systems with Maximum Working Pressure
of 63 PSI
ANSI/ASTM F1199-1988 铸造(所有温度和压力)和焊接管线滤网(150
PSIG 和150oF最大值)的规范 Specification for Cast (All
Temperatures and Pressures) and Welded Pipe
Line Strainers (150 PSIG and 150oF Maximum)
ANSI/ASTM F1281-2007 交联聚乙烯/铝/交联聚乙烯(PEX-AL-PEX)压力管规范
Specification for Crosslinked Polyethylene/Aluminum/Crosslinked
Polyethylene (PEX-AL-PEX) Pressure Pipe
ANSI/ASTM F1282-2005 聚乙烯/铝/聚乙烯(PE-AL-PE)合成压力管规范
Specification for Polyethylene/Aluminum/Polyethylene
(PE-AL-PE) Composite Pressure Pipe
ANSI/ASTM F1335-2004 高温设备用压力标定复合管规范 Specification
for Pressure-Rated Composite Pipe for Elevated
Temperature Service
ANSI/ASTM F1483-1999 定向聚氯乙烯(PVCO)压力管的标准规范 Specification
for Oriented Poly (Vinyl Chloride), PVCO, Pressure
Pipe
ANSI/ASTM F1589-1996 塑料管裂纹快速扩展临界压力测定方法 Test
Method for Determination of the Critical Pressure
for Rapid Crack Propagation in Plastic Pipe
ANSI/ASTM F1865-2002 交联聚乙烯管(PEX)用带压力套管的机械冷膨胀插入式配件规范
Specification for Mechanical Cold Expansion
Insert Fitting with Compression Sleeve for Crosslinked
Polyethylene PEX Tubing
ANSI/ASTM F1964-2006 压力油炸锅和锅状油炸锅性能试验方法 Test
Method for the Performance of Pressure and Kettle
Fryers
ANSI/ASTM F1974-2004 聚乙烯/铝/聚乙烯和交联聚乙烯/铝/交联聚乙烯复合压力管用金属内插件规范
Specification for Metal Insert Fittings for
Polyethylene/Aluminum/Polyethylene and Crosslinked
Polyethylene/Aluminum/Crosslinked Polyethylene
Composite Pressure Pipe
ANSI/ASTM F2070-2001 压力和差动压力电及光纤换能器规范 Specification
for Transducers, Pressure and Differential Pressure,
Electrical and Fiber Optic
ANSI/ASTM F2164-2002 采用液压法进行聚乙烯压力管道系统场漏试验的惯例
Practice for Field Leak Testing of Polyethylene
(PE) Pressure Piping Systems Using Hydrostatic
Pressure
ANSI/ASTM F2222-2002 医用抽吸设备.真空或压力源驱动的抽吸设备 Medical
Suction Equipment-suction Equipment Powered
from a Vacuum or Pressure Source
ANSI/ASTM F2389-2007 额定压力聚丙烯(PP)管道系统规范 Specification
for Pressure-rated Polypropylene Pp Piping Systems
ANSI/ASTM F2562-2007 无压力排水和污水用钢增强热塑性肋状管和配件规范
Specification for Steel Reinforced Thermoplastic
Ribbed Pipe and Fittings for Non-Pressure Drainage
and Sewerage
ANSI/ASTM F2569-2007 体育运动用表面压力还原性能评估的试验方法 Test
Method for Evaluating the Force Reduction Properties
of Surfaces for Athletic Use
ANSI/ASTM F690-1996 热塑压力管道灌溉系统地下安装惯例 Practice
for Underground Installation of Thermoplastic
Pressure Piping Irrigation Systems
ANSI/AWS D14.5-1997 压力机和压力元件焊接规范 Specification
for Welding of Presses and Press Components
ANSI/AWWA C111-2006 韧性铸铁压力管和配件的橡胶垫接头 Rubber-Gasket
Joints for Ductile-Iron Pressure Pipe and Fittings
ANSI/AWWA C300-2004 水及其他液体用钢制圆柱形加筋混凝土压力管 Reinforced
Concrete Pressure Pipe, Steel Cylinder Type,
for Water and Other Liquids
ANSI/AWWA C301-2007 预应力混凝土压力管.钢筒型 Prestressed
Concrete Pressure Pipe, Steel-Cylinder Type
ANSI/AWWA C302-2004 非圆柱形钢筋混凝土压力管 Reinforced
Concrete Pressure Pipe, Noncylinder Type
ANSI/AWWA C303-2002 钢筒形条绕的混凝土压力管 Concrete Pressure
Pipe, Bar-Wrapped, Steel Cylinder Type
ANSI/AWWA C401-2003 配水系统用4到16英寸(100mm到400mm)的石棉水泥压力管的选择
Selection of Asbestos-Cement Pressure Pipe,
4-in through 16-in (100-mm through 400-mm) for
Water Distribution Systems
ANSI/AWWA C605-2005 水处理.输水用聚氯乙烯PVC压力管及配件的地下安装
Underground Installation of Polyvinyl Chloride
(PVC) Pressure Pipe and Fittings for Water
ANSI/AWWA C900-2007 输水和配水用4英寸～12英寸(100mm～300mm)聚氯乙烯(PVC)压力管和装配配件
Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated
Fittings 4-Inch to 12-Inch (100 mm Through 300
mm) for Water Transmission and Distribution
ANSI/AWWA C901-2002 1/2到3英寸(13-76毫米)聚乙烯压力给水管
Polyethylene (PE) Pressure Pipe and Tubing,
1/2 in (13 mm) through 3 in (76 mm), for Water
Service
ANSI/AWWA C903-2005 给水用1/2 In.(12 mm)到2 In.(50
mm)聚乙烯-铝-聚乙烯和交联聚乙烯-铝-交联聚乙烯复合压力管 Polyethylene-Aluminum-Polyethylene
& Crosslinked Polyethylene-Aluminum-Crosslinked
Polyethylene Composite Pressure Pipes, 1/2 In.
(12 mm) Through 2 In. (50 mm), for Water Service
ANSI/AWWA C904-2006 供水用0.5～3英寸(12～76 mm)交联聚乙烯压力管道
Cross-Linked Polyethylene Pressure Pipes, 1/2
In. (12 mm) Through 3 In. (76 mm) for Water
Service
ANSI/AWWA C905-1997 14in.-36in.(聚氯乙烯(PVC)压力输水管和成品配件
Polyvinyl Chloride (PVC) Water Transmission
Pipe (Nominal Diameters 14-36 inches)
ANSI/AWWA C906-2007 配水和输水用4"(100mm)～63"(1600mm)聚乙烯(PE)压力管和配件
PE Pressure Pipe & Fittings, 4" (100
mm) Through 63" (1600 mm), for Water Distribution
and Transmission
ANSI/AWWA C907-2004 给水用注模聚氯乙烯4至12英寸压力管配件 Injection-Molded
Polyvinyl Chloride (PVC) Pressure Fittings,
4 In. to 12 In. for Water Distribution
ANSI/AWWA C909-2002 给排水用4至12英寸(100至300mm)分子定向聚氯乙烯(PVCO)压力管
Molecularly Oriented Polyvinyl Chloride (PVCO)
Pressure Pipe, 4 in. Through 12 in. (100 mm
Through 300 mm), for Water Distribution
ANSI/AWWA C950-2007 玻璃纤维压力管 Fiberglass Pressure
Pipe
ANSI/DASMA 115-2005 测试车库门用标准方法:在投掷物冲击和循环风压力下结构性能的测定
Standard Method for Testing Garage Doors: Determination
of Structural Performance Under Missile Impact
and Cyclic Wind Pressure
ANSI/FCI 69-1-1989 疏水阀的压力额定值标准 Pressure Rating
Standard for Steam Traps
ANSI/FCI 73-1-1998 Y型滤器压力额定值标准 Pressure Rating
Standard for "Y" Type Strainers
ANSI/FCI 78-1-1998 不包括Y型在内的管道滤器压力额定值标准 Pressure
Rating Standard for Pipeline Strainers Other
than "Y" Type
ANSI/FCI 79-1-2003 减压器压力额定值的验证 Proof of Pressure
Ratings for Pressure Reducing Regulators
ANSI/IAS NGV4.7-1999 天然气分装系统用自动压力控制阀 Automatic
Pressure-Operated Valves for Natural Gas Dispensing
Systems
ANSI/SAE J188-1998 动力转向压力软管.高容积膨胀型 Power Steering
Pressure Hose - High Volumetric Expansion Type
ANSI/SAE J190-1998 金属丝编织的动力转向压力软管 Power Steering
Pressure Hose-Wire Braid
ANSI/SAE J191-1998 动力转向压力软管.低容积膨胀型 Power Steering
Pressure Hose - Low Volumetric Expansion Type
ANSI/SAE J2050-1993 高温助力转向压力软管 High-Temperature
Power Steering Pressure Hose
ANSI/TIA-455-41A-1993 光纤电缆的抗压力负荷性能 Compressive
Loading Resistance of Fiber Optic Cable
ANSI/UL 136-2006 压力炊具 Pressure Cookers
ANSI/UL 144-2001 液化石油气压力调节阀的安全标准 Standard for
Safety for Pressure-Regulating Valves for LP
Gas
ANSI/UL 404-2006 压缩气体装置用压力指示计的安全标准 Standard
for Safety for Gauges, Indicating Pressure,
for Compressed Gas Service
ASME B16.18-2001 铸铜合金软钎焊连接压力管件 (Cast copper
alloy solder joint pressure fittings)
ASME B16.22-2001 锻铜和铜合金钎焊压力配件 (Wrought copper
and copper alloy solder joint pressure fittings)
ASME B16.50-2001 锻造铜及铜合金硬焊结合压力配件 (Wrought copper
and copper alloy braze-joint pressure fittings)
ASME B31.3 Cases NO. 2-1993 压力管道用套管规程.套管141:在ANSI/ASME
B 31.3管道标准中铝合金法兰的使用规则 (Cases code for pressure
piping - Case 141: Rules for use of aluminium
alloy flanges in ANSI/ASME B 31.3 piping)
ASME B31G-1991 用于测定受腐蚀管道剩余强度的手册.MSME B31 压力管道规范的补充件
(Manual for determining the remaining strength
of corroded pipelines; A supplement to ASME
B31 code for pressure piping)
ASME B40.100-1998 压力计及其附件 (Pressure gauges and
gauge attachments)
ASME B5.52M-1980 GAP型(米制)通用单点机械动力压力机 (Mechanical
power presses - General purpose single point,
GAP Type (Metric))
ASME BPVC CCB BPV Supplement 1 ASME锅炉和压力容器规范.CCB
BPV.锅炉和压力容器.补充件1 (ASME Boiler and Pressure Vessel
Code - Code Cases: CCB BPV; Boilers and Pressure
Vessels; Supplement 1)
ASME BPVC CCB BPV-2001 ASME锅炉和压力容器规程.标准件:CCB
BPV.锅炉和压力容器 (ASME Boiler & Pressure Vessel
Code - Code Cases: CCB BPV; Boilers and Pressure
Vessels)
ASME BPVC CCB NC Supplement 1- ASME锅炉和压力容器规范.CCB
NC.核部件.补充件1 (ASME Boiler and Pressure Vessel
Code - Code Cases: CCB NC; Nuclear Components;
Supplement 1)
ASME BPVC CCB NC-2001 ASME锅炉和压力容器规程.标准件:CCB
NC.核元件 (ASME Boiler & Pressure Vessel Code
- Code Cases: CCB NC; Nuclear Components)
ASME BPVC Section 1-2001 ASME锅炉和压力容器规程.第1节:电力锅炉建造规则
(ASME Boiler & Pressure Vessel Code - Section
1: Rules for Construction of Power Boilers)
ASME BPVC Section 10-2001 ASME锅炉和压力容器规程.第10节:纤维增强塑料压力容器
(ASME Boiler & Pressure Vessel Code - Section
10: Fiber-Reinforced Plastic Pressure Vessels)
ASME BPVC Section 11-2001 ASME锅炉和压力容器规程.第11节:核电厂元部件在使用中进行检查的规则
(ASME Boiler & Pressure Vessel Code - Section
11: Rules for Inservice Inspection of Nuclear
Power Plant Components)
ASME BPVC Section 2 Part A-200 ASME锅炉和压力容器规程.第2节:材料.第A部分:钢铁材料规范
(ASME Boiler & Pressure Vessel Code - Section
2: Materials; Part A: Ferrous Material Specifications)
ASME BPVC Section 2 Part B-200 ASME锅炉和压力容器规程.第2节:材料.第B部分:有色金属材料规范
(ASME Boiler & Pressure Vessel Code - Section
2: Materials; Part B: Nonferrous Material Specifications)
ASME BPVC Section 2 Part C-200 ASME锅炉和压力容器规程.第2节:材料.第C部分:焊条、焊极和填充材料规范
(ASME Boiler & Pressure Vessel Code - Section
2: Materials; Part C: Specifications for Welding
Rods, Electrodes and Filler Metals)
ASME BPVC Section 2 Part D-200 ASME锅炉和压力容器规程.第2节:材料.第D部分:性能
(ASME Boiler & Pressure Vessel Code - Section
2: Materials; Part D: Properties)
ASME BPVC Section 3 Division 1 ASME锅炉和压力容器规程.第3节:核设施元部件制造规则.第1分册.第NF子节.支撑物
(ASME Boiler & Pressure Vessel Code - Section
3: Rules for Construction of Nuclear Facility
Components; Division 1; Subsection NF; Supports)
ASME BPVC Section 3 Division 1 ASME锅炉和压力容器规程.第3节:核设施元部件制造规则.第1分册.第NF子节.支撑物
(ASME Boiler & Pressure Vessel Code - Section
3: Rules for Construction of Nuclear Facility
Components; Division 1; Subsection NF; Supports)
ASME BPVC Section 3 Division 1 ASME锅炉和压力容器规程.第3节:核设施元部件制造规则.第1分册.第NF子节.支撑物
(ASME Boiler & Pressure Vessel Code - Section
3: Rules for Construction of Nuclear Facility
Components; Division 1; Subsection NF; Supports)
ASME BPVC Section 3 Division 1 ASME锅炉和压力容器规程.第3节:核设施元部件制造规则.第1分册.第NF子节.支撑物
(ASME Boiler & Pressure Vessel Code - Section
3: Rules for Construction of Nuclear Facility
Components; Division 1; Subsection NF; Supports)
ASME BPVC Section 3 Division 1 ASME锅炉和压力容器规程.第3节:核设施元部件制造规则.第1分册.第NF子节.支撑物
(ASME Boiler & Pressure Vessel Code - Section
3: Rules for Construction of Nuclear Facility
Components; Division 1; Subsection NF; Supports)
ASME BPVC Section 3 Division 1 ASME锅炉和压力容器规程.第3节:核设施元部件制造规则.第1分册.第NF子节.支撑物
(ASME Boiler & Pressure Vessel Code - Section
3: Rules for Construction of Nuclear Facility
Components; Division 1; Subsection NF; Supports)
ASME BPVC Section 3 Division 1 ASME锅炉和压力容器规程.第3节:核设施元部件制造规则.第1分册.第NF子节.支撑物
(ASME Boiler & Pressure Vessel Code - Section
3: Rules for Construction of Nuclear Facility
Components; Division 1; Subsection NF; Supports)
ASME BPVC Section 3 Division 1 ASME锅炉和压力容器规程.第3节:核设施元部件制造规则.第1分册.第NF子节.支撑物
(ASME Boiler & Pressure Vessel Code - Section
3: Rules for Construction of Nuclear Facility
Components; Division 1; Subsection NF; Supports)
ASME BPVC Section 3 Division 2 ASME锅炉和压力容器规程.第3节:核设施元部件制造规则.第2分册.混凝土反应堆容器和外壳标准
(ASME Boiler & Pressure Vessel Code - Section
3: Rules for Construction of Nuclear Facility
Components; Division 2; Code for Concrete Reactor
Vessels and Containments)
ASME BPVC Section 3 Division 3 ASME锅炉和压力容器规程.第3节:核设施元部件制造规则.第3分册.消耗核燃料和高等级放射性废物用外壳系统和运
(ASME Boiler & Pressure Vessel Code - Section
3: Rules for Construction of Nuclear Facility
Components; Division 3; Containment Systems
and Transport Packaging for Spent Nuclear Fuel
and High Level Rad)
ASME BPVC Section 3 NCA-2001 ASME锅炉和压力容器规程.第3节:核设施元部件制造规则.第NCA子节.1和2分册的一般要求
(ASME Boiler & Pressure Vessel Code - Section
3: Rules for Construction of Nuclear Facility
Components; Subsection NCA; General Requirements
for Division 1 and Division 2)
ASME BPVC Section 4-2001 ASME锅炉和压力容器规程.第4节:加热锅炉的建造规则
(ASME Boiler & Pressure Vessel Code - Section
4: Rules for Construction of Heating Boilers)
ASME BPVC Section 5-2001 ASME锅炉和压力容器规程.第5节:无损检验
(ASME Boiler & Pressure Vessel Code - Section
5: Nondestructive Examination)
ASME BPVC Section 6-2001 ASME锅炉和压力容器规程.第6节:加热锅炉维护和操作的推荐规则
(ASME Boiler & Pressure Vessel Code - Section
6: Recommended Rules for Care and Operation
of Heating Boilers)
ASME BPVC Section 7-2001 ASME锅炉和压力容器规程.第7节:电力锅炉维护的推荐指南
(ASME Boiler & Pressure Vessel Code - Section
7: Recommended Guidelines for the Care of Power
Boilers)
ASME BPVC Section 8 Division 1 ASME锅炉和压力容器规程.第8节:压力容器的制造规则.第1分册.压力容器
(ASME Boiler & Pressure Vessel Code - Section
8: Rules for Construction of Pressure Vessels;
Division 1; Pressure Vessels)
ASME BPVC Section 8 Division 2 ASME锅炉和压力容器规程.第8节:压力容器的制造规则.第2分册.替代规则
(ASME Boiler & Pressure Vessel Code - Section
8: Rules for Construction of Pressure Vessels;
Division 2; Alternative Rules)
ASME BPVC Section 8 Division 3 ASME锅炉和压力容器规程.第8节:压力容器的制造规则.第3分册.高压容器制造的替代规则
(ASME Boiler & Pressure Vessel Code - Section
8: Rules for Construction of Pressure Vessels;
Division 3; Alternative Rules for Construction
of High Pressure Vessels)
ASME BPVC Section 9-2001 ASME锅炉和压力容器规则.第9节:焊接和钎焊合格
(ASME Boiler & Pressure Vessel Code - Section
9: Welding and Brazing Qualifications)
ASME MC 88.1-1972 压力传感器的动态校准导则 (A guide for
the dynamic calibration of pressure transducers)
ASME PCC-1-2000 压力边界螺栓法兰连接组件导则 (Guidelines for
pressure boundary bolted flange joint assembly)
ASME PTC 19.2-1987 装置和仪器:第2部分:压力测量 (Instruments
and apparatus - Part 2: Pressure measurement)
ASME PTC 20.3-1970 汽轮发电机组用压力控制系统 (Pressure control
systems used on steam turbine-generator units)
ASTM A 1017/A 1017M-2007 铬钼钨合金钢压力容器板材的标准规范 Standard
Specification for Pressure Vessel Plates, Alloy
Steel, Chromium-Molybdenum-Tungsten
ASTM A 1041/A 1041M-2004 较高强度铬-钼-钨合金钢压力容器板的标准规范
Standard Specification for Pressure Vessel Plates,
Alloy Steel, Higher Strength Chromium-Molybdenum-Tungsten
ASTM A 1048/A 1048M-2006 高温工作的高强度铬钼钨合金钢压力容器锻件的标准规范
Standard Specification for Pressure Vessel Forgings,
Alloy Steel, Higher Strength Chromium-Molybdenum-Tungsten
for Elevated Temperature Service
ASTM A 1049/A 1049M-2006 压力容器和相关元件用铁素体/奥氏体(双重)不锈钢锻件的标准规范
Standard Specification for Stainless Steel Forgings,
Ferritic/Austenitic (Duplex), for Pressure Vessels
and Related Components
ASTM A 20/A 20M-2006 压力容器用钢板一般要求的标准规范 Standard
Specification for General Requirements for Steel
Plates for Pressure Vessels
ASTM A 203/A 203M-1997 压力容器用镍合金钢板的标准规范 Standard
Specification for Pressure Vessel Plates, Alloy
Steel, Nickel
ASTM A 204/A 204M-2003 压力容器用钼合金钢板的标准规范 Standard
Specification for Pressure Vessel Plates, Alloy
Steel, Molybdenum
ASTM A 225/A 225M-2003 压力容器用锰钒镍合金钢板标准规范 Standard
Specification for Pressure Vessel Plates, Alloy
Steel, Manganese-Vanadium-Nickel
ASTM A 240/A 240M-2007 压力容器和一般设备用铬及铬-镍不锈钢厚板材、薄板材和带材的标准规范
Standard Specification for Chromium and Chromium-Nickel
Stainless Steel Plate, Sheet, and Strip for
Pressure Vessels and for General Applications
ASTM A 266/A 266Ma-2003 压力容器部件用碳素钢锻件标准规范 Standard
Specification for Carbon Steel Forgings for
Pressure Vessel Components
ASTM A 278/A 278M-2001 650华氏温度以下的含压力部件用灰口铁铸件的标准规范
Standard Specification for Gray Iron Castings
for Pressure-Containing Parts for Temperatures
Up to 650°F (350°C)
ASTM A 285/A 285M-2003 压力容器用低和中等抗拉强度的碳素钢板的标准规范
Standard Specification for Pressure Vessel Plates,
Carbon Steel, Low- and Intermediate-Tensile
Strength
ASTM A 299/A 299M-2004 压力容器用锰硅碳钢板的标准规范 Standard
Specification for Pressure Vessel Plates, Carbon
Steel, Manganese-Silicon
ASTM A 302/A 302M-2003 压力容器用锰钼和锰钼镍合金钢板的标准规范
Standard Specification for Pressure Vessel Plates,
Alloy Steel, Manganese-Molybdenum and Manganese-Molybdenum-Nickel
ASTM A 31-2004 压力容器铆接用钢铆钉和铆接棒的标准规范 Standard
Specification for Steel Rivets and Bars for
Rivets, Pressure Vessels
ASTM A 336/A 336M-2007 压力和高温部件用合金钢锻件的标准规范 Standard
Specification for Alloy Steel Forgings for Pressure
and High-Temperature Parts
ASTM A 353/A 353M-2004 压力容器用经二次正火及回火处理的含9％镍的合金钢板标准规范
Standard Specification for Pressure Vessel Plates,
Alloy Steel, 9 Percent Nickel, Double-Normalized
and Tempered
ASTM A 372/A 372M-2003 薄壁压力容器用碳钢和合金钢锻件的标准规范
Standard Specification for Carbon and Alloy
Steel Forgings for Thin-Walled Pressure Vessels
ASTM A 377-2003 球墨铸铁压力管规范用索引标准 Standard Index
of Specifications for Ductile-Iron Pressure
Pipe
ASTM A 387/A 387Ma-2006 压力容器用铬钼合金钢板的标准规范 Standard
Specification for Pressure Vessel Plates, Alloy
Steel, Chromium-Molybdenum
ASTM A 414/A 414M-2007 压力容器用碳钢薄板材的标准规范 Standard
Specification for Steel, Sheet, Carbon, for
Pressure Vessels
ASTM A 455/A 455M-2003 压力容器用高强度碳锰钢板标准规范 Standard
Specification for Pressure Vessel Plates, Carbon
Steel, High-Strength Manganese
ASTM A 479/A 479Ma-2006 锅炉及其它压力容器用不锈钢棒材与型材的标准规范
Standard Specification for Stainless Steel Bars
and Shapes for Use in Boilers and Other Pressure
Vessels
ASTM A 508/A 508Mb-2005 压力容器用经淬火和回火真空处理的碳素钢与合金钢锻件的标准规范
Standard Specification for Quenched and Tempered
Vacuum-Treated Carbon and Alloy Steel Forgings
for Pressure Vessels
ASTM A 515/A 515M-2003 中温及高温压力容器用碳素钢板的标准规范 Standard
Specification for Pressure Vessel Plates, Carbon
Steel, for Intermediate- and Higher-Temperature
Service
ASTM A 516/A 516M-2006 中温及低温压力容器用碳素钢板材的标准规范
Standard Specification for Pressure Vessel Plates,
Carbon Steel, for Moderate- and Lower-Temperature
Service
ASTM A 517/A 517M-2006 压力容器用经回火与淬火的高强度合金钢板 Standard
Specification for Pressure Vessel Plates, Alloy
Steel, High-Strength, Quenched and Tempered
ASTM A 533/A 533M-1993 压力容器用经回火和淬火的锰钼及锰钼镍合金钢板
Standard Specification for Pressure Vessel Plates,
Alloy Steel, Quenched and Tempered, Manganese-Molybdenum
and Manganese-Molybdenum-Nickel
ASTM A 537/A 537M-2006 压力容器用热处理的碳锰硅钢板的标准规范 Standard
Specification for Pressure Vessel Plates, Heat-Treated,
Carbon-Manganese-Silicon Steel
ASTM A 541/A 541M-2005 压力容器部件用经淬火和回火的碳素钢及合金钢锻件的标准规范
Standard Specification for Quenched and Tempered
Carbon and Alloy Steel Forgings for Pressure
Vessel Components
ASTM A 542/A 542M-1999 压力容器用经回火和淬火的铬钼、铬钼钒及铬钼钒钛硼合金钢板的标准规范
Standard Specification for Pressure Vessel Plates,
Alloy Steel, Quenched-and-Tempered, Chromium-Molybdenum,
and Chromium-Molybdenum-Vanadium
ASTM A 543/A 543M-1993 压力容器用经回火和淬火的镍铬钼合金钢板的标准规范
Standard Specification for Pressure Vessel Plates,
Alloy Steel, Quenched and Tempered Nickel-Chromium-Molybdenum
ASTM A 553/A 553M-2006 压力容器用经淬火和回火的含8%和9%镍的合金钢板的标准规范
Standard Specification for Pressure Vessel Plates,
Alloy Steel, Quenched and Tempered 8 and 9 Percent
Nickel
ASTM A 562/A 562M-2006 玻璃或扩散金属镀层的压力容器用锰钛合金碳素钢板
Standard Specification for Pressure Vessel Plates,
Carbon Steel, Manganese-Titanium for Glass or
Diffused Metallic Coatings
ASTM A 592/A 592M-2004 压力容器用经回火和淬火的高强度低合金钢锻制配件和零件标准规范
Standard Specification for High-Strength Quenched
and Tempered Low-Alloy Steel Forged Fittings
and Parts for Pressure Vessels
ASTM A 608/A 608M-2006 高温压力设备用离心铸造的铁铬镍高合金钢管标准规范
Standard Specification for Centrifugally Cast
Iron-Chromium-Nickel High-Alloy Tubing for Pressure
Application at High Temperature
ASTM A 612/A 612M-2003 中温和低温压力容器用高强度碳素钢板的标准规范
Standard Specification for Pressure Vessel Plates,
Carbon Steel, High Strength, for Moderate and
Lower Temperature Service
ASTM A 645/A 645M-2005 经特殊热处理的5%镍合金钢压力容器板的标准规范
Standard Specification for Pressure Vessel Plates,
Five Percent Nickel Alloy Steel, Specially Heat
Treated
ASTM A 662/A 662M-2003 中温和低温压力容器用碳锰硅钢板的标准规范
Standard Specification for Pressure Vessel Plates,
Carbon-Manganese-Silicon Steel, for Moderate
and Lower Temperature Service
ASTM A 696a-1990 压力管道部件用特级热锻或冷精轧碳素钢棒标准规范 Standard
Specification for Steel Bars, Carbon, Hot-Wrought
or Cold-Finished, Special Quality, for Pressure
Piping Components
ASTM A 723/A 723M-2002 高强度压力元件用合金钢锻件的标准规范 Standard
Specification for Alloy Steel Forgings for High-Strength
Pressure Component Application
ASTM A 724/A 724M-2004 叠层焊接的压力容器用经淬火及回火的碳锰硅钢压力容器板的标准规范
Standard Specification for Pressure Vessel Plates,
Carbon-Manganese-Silicon Steel, Quenched and
Tempered, for Welded Layered Pressure Vessels
ASTM A 734/A 734Ma-1987 经淬火和回火的合金钢与高强度低合金钢压力容器板标准规范
Standard Specification for Pressure Vessel Plates,
Alloy Steel and High-Strength Low-Alloy Steel,
Quenched-and-Tempered
ASTM A 735/A 735M-2003 中温和低温压力容器用低碳锰钼钶合金钢板的标准规范
Standard Specification for Pressure Vessel Plates,
Low-Carbon Manganese-Molybdenum-Columbium Alloy
Steel, for Moderate and Lower Temperature Service
ASTM A 736/A 736M-2003 压力容器用低碳时效硬化的镍铜铬钼铌和镍铜锰钼铌合金钢板的标准规范
Standard Specification for Pressure Vessel Plates,
Low-Carbon Age-Hardening Nickel-Copper-Chromium-Molybdenum-Columbium
and Nickel-Copper-Manganese-Molybdenum-Columbium
Alloy Steel
ASTM A 737/A 737M-1999 高强度低合金钢压力容器板的标准规范 Standard
Specification for Pressure Vessel Plates, High-Strength,
Low-Alloy Steel
ASTM A 738/A 738M-2005 中温和低温设备用经热处理的碳锰硅钢压力容器板的标准规范
Standard Specification for Pressure Vessel Plates,
Heat-Treated, Carbon-Manganese-Silicon Steel,
for Moderate and Lower Temperature Service
ASTM A 748/A 748M-1987 压力容器用静电铸造的白口铁-灰口铁双金属柱
Statically Cast Chilled White Iron-Gray Iron
Dual Metal Rolls for Pressure Vessel Use
ASTM A 765/A 765M-2007 符合强制韧性要求的碳素钢和低合金钢压力容器部件锻件的标准规范
Standard Specification for Carbon Steel and
Low-Alloy Steel Pressure-Vessel-Component Forgings
with Mandatory Toughness Requirements
ASTM A 782/A 782M-2006 经淬火和回火的锰铬钼硅锆合金钢压力容器板的标准规范
Standard Specification for Pressure-Vessel Plates,
Quenched-and-Tempered, Manganese-Chromium-Molybdenum-Silicon
Zirconium Alloy Steel
ASTM A 832/A 832M-2006 压力容器用铬钼钒合金钢板的标准规范 Standard
Specification for Pressure Vessel Plates, Alloy
Steel, Chromium-Molybdenum-Vanadium
ASTM A 836/A 836M-2002 玻璃衬里的管道系统和压力容器设备用钛稳定的碳素钢锻件标准规范
Standard Specification for Titanium-Stabilized
Carbon Steel Forgings for Glass-Lined Piping
and Pressure Vessel Service
ASTM A 841/A 841Ma-2003 用热机械控制法(TMCP)生产的压力容器用钢板的标准规范
Standard Specification for Steel Plates for
Pressure Vessels, Produced by Thermo-Mechanical
Control Process (TMCP)
ASTM A 844/A 844M-2004 压力容器用直接淬火加工的含镍9%的合金钢板标准规范
Standard Specification for Steel Plates, 9 %
Nickel Alloy, for Pressure Vessels, Produced
by the Direct-Quenching Process
ASTM A 859/A 859M-2004 压力容器部件用时效硬化合金钢锻件的标准规范
Standard Specification for Age-Hardening Alloy
Steel Forgings for Pressure Vessel Components
ASTM A 873/A 873M-1987 压力容器用铬钼合金钢薄板和带材 Steel
Sheet and Strip, Chromium-Molybdenum Alloy for
Pressure Vessels
ASTM A 905-2004 压力容器缠绕用钢丝的标准规范 Standard Specification
for Steel Wire, Pressure Vessel Winding
ASTM ANS/ISO 10079-3-1999 医疗吸引设备.第3部分:与美国国家标准有偏差的ASTM国际标准认可的真空或用压力驱动吸引设备
Medical Suction Equipment - Part 3: Suction
Equipment Powered from a Vacuum or Pressure
Source Approved as an American National Standard
with Deviations by ASTM International
ASTM B 171/B 171M-2004 压力容器、冷凝器和热交换器用铜合金板材和薄板材的标准规范
Standard Specification for Copper-Alloy Plate
and Sheet for Pressure Vessels, Condensers,
and Heat Exchangers
ASTM B 469-1994 压力设备用无缝铜合金管 Seamless Copper
Alloy Tubes for Pressure Applications
ASTM B 548-2003 压力容器用铝合金板的超声波检验的标准试验方法 Standard
Test Method for Ultrasonic Inspection of Aluminum-Alloy
Plate for Pressure Vessels
ASTM B 834-1995 压力强化粉末冶金铁镍铬钼和镍铬钼钶(Nb)合金管法兰、管配件、阀门和零件标准规范
Standard Specification for Pressure Consolidated
Powder Metallurgy Iron-Nickel-Chromium-Molybdenum
(UNS N08367) and Nickel-Chromium-Molybdenum-Columbium
(Nb) (UNS N06625) Alloy Pipe Flanges, Fittings,
Valves, and Parts
ASTM B 96/B 96M-2006 一般用途和压力容器用铜硅合金板材、薄板、带材和轧制棒材的标准规范
Standard Specification for Copper-Silicon Alloy
Plate, Sheet, Strip, and Rolled Bar for General
Purposes and Pressure Vessels
ASTM C 1306a-2005 液用防水薄膜抗静液压力的标准试验方法 Standard
Test Method for Hydrostatic Pressure Resistance
of a Liquid-Applied Waterproofing Membrane
ASTM C 231-2004 用压力法测定新搅拌混凝土中空气含量的标准试验方法 Standard
Test Method for Air Content of Freshly Mixed
Concrete by the Pressure Method
ASTM C 296-2000 石棉水泥压力管的标准规范 Standard Specification
for Asbestos-Cement Pressure Pipe
ASTM C 361-2005 钢筋混凝土低水头压力管标准规范 Standard Specification
for Reinforced Concrete Low-Head Pressure Pipe
ASTM C 361M-2005 钢筋混凝土低水头压力管的标准规范(米制) Standard
Specification for Reinforced Concrete Low-Head
Pressure Pipe [Metric]
ASTM C 601-1985 玻璃管的压力试验 Pressure Test on Glass
Pipe
ASTM C 684-1999 混凝土压力试样的制作、快速养护和测试的标准试验方法 Standard
Test Method for Making, Accelerated Curing,
and Testing Concrete Compression Test Specimens
ASTM C 830-2000 用真空压力法测定成型耐火材料表观空隙率、吸水性、表观比重和体密度的标准试验方法
Standard Test Methods for Apparent Porosity,
Liquid Absorption, Apparent Specific Gravity,
and Bulk Density of Refractory Shapes by Vacuum
Pressure
ASTM C 973-1987 用压力法从喷制的碱性耐火产品中制备试验样品 Preparing
Test Specimens from Basic Refractory Gunning
Products by Pressing
ASTM C 975-1987 用压力法从捣实碱性耐火产品中制备试验样品的标准实施规程
Standard Practice for Preparing Test Specimens
from Basic Refractory Ramming Products by Pressing
ASTM D 1143/D 1143M-2007 静态轴向压力载荷下深地基的标准试验方法
Standard Test Methods for Deep Foundations Under
Static Axial Compressive Load
ASTM D 1599-1999 塑料管道和配件耐短时液压力的标准试验方法 Standard
Test Method for Resistance to Short-Time Hydraulic
Pressure of Plastic Pipe, Tubing, and Fittings
ASTM D 1657-2002 用压力液体比重计测定轻烃类物质的密度或相对密度的标准试验方法
Standard Test Method for Density or Relative
Density of Light Hydrocarbons by Pressure Hydrometer
ASTM D 2112a-2001 用压力容器法测定防腐蚀矿物绝缘油氧化稳定性的标准试验方法
Standard Test Method for Oxidation Stability
of Inhibited Mineral Insulating Oil by Pressure
Vessel
ASTM D 2143-2000 增强热固塑料管耐周期性压力强度的标准试验方法 Standard
Test Method for Cyclic Pressure Strength of
Reinforced, Thermosetting Plastic Pipe
ASTM D 2241-2005 聚氯乙烯(PVC)压力标定管的标准规范(SDR系列)
Standard Specification for Poly(Vinyl Chloride)
(PVC) Pressure-Rated Pipe (SDR Series)
ASTM D 2293-1996 用压力荷载法测定金属之间胶粘剂蠕变性能的标准试验方法
Standard Test Method for Creep Properties of
Adhesives in Shear by Compression Loading (Metal-to-Metal)
ASTM D 2434-1968 在常水头压力下颗粒状土壤渗水率的标准试验方法 Standard
Test Method for Permeability of Granular Soils
(Constant Head)
ASTM D 2503-1992 蒸气压力热电测量法测定烃类相对分子质量(分子量)的标准试验方法
Standard Test Method for Relative Molecular
Mass (Molecular Weight) of Hydrocarbons by Thermoelectric
Measurement of Vapor Pressure
ASTM D 2513a-2007 热塑性煤气压力管、管道系统及配件的标准规范 Standard
Specification for Thermoplastic Gas Pressure
Pipe, Tubing, and Fittings
ASTM D 2585-1968 丝线缠绕的压力容器的准备及抗拉试验方法 Test Method
for Preparation and Tension Testing of Filament-Wound
Pressure Vessels
ASTM D 2586-1968 玻璃增强塑料圆筒液体静压力强度的试验方法 Test Method
for Hydrostatic Compressive Strength of Glass-Reinforced
Plastic Cylinders
ASTM D 2759-2000 在正压力下从变压器中抽取气体样品的标准实施规程 Standard
Practice for Sampling Gas from a Transformer
Under Positive Pressure
ASTM D 2774-2004 热塑(性)压力管的地下安装标准规程 Standard
Practice for Underground Installation of Thermoplastic
Pressure Piping
ASTM D 2782-2002 润滑液极端压力特性的标准试验法(泰姆肯法) Standard
Test Method for Measurement of Extreme-Pressure
Properties of Lubricating Fluids (Timken Method)
ASTM D 2837-2004 获得热塑性管道材料静水压设计基数和热塑管道制品压力设计基数的标准试验方法
Standard Test Method for Obtaining Hydrostatic
Design Basis for Thermoplastic Pipe Materials
or Pressure Design Basis for Thermoplastic Pipe
Products
ASTM D 2844-2007 压实土的阻抗R值和膨胀压力的标准试验方法 Standard
Test Method for Resistance R-Value and Expansion
Pressure of Compacted Soils
ASTM D 2878-1995 润滑油表面蒸气压力和分子量评估的标准试验方法 Standard
Test Method for Estimating Apparent Vapor Pressures
and Molecular Weights of Lubricating Oils
ASTM D 2879-1997 蒸气压力计测定液体的蒸气压力-温度关系及起始分解温度的标准试验方法
Standard Test Method for Vapor Pressure-Temperature
Relationship and Initial Decomposition Temperature
of Liquids by Isoteniscope
ASTM D 2889-1995 石油馏分燃料真蒸气压力计算的标准试验方法 Standard
Test Method for Calculation of True Vapor Pressures
of Petroleum Distillate Fuels
ASTM D 2924-2001 增强的热固树脂管抗外部压力性能的标准试验方法 Standard
Test Method for External Pressure Resistance
of "Fiberglass" (Glass-Fiber-Reinforced
Thermosetting-Resin) Pipe
ASTM D 3003-2001 金属衬底表面有机涂层耐压力斑迹和抗粘连性标准试验方法
Standard Test Method for Pressure Mottling and
Blocking Resistance of Organic Coatings on Metal
Substrates
ASTM D 3070-2000 加压制品快速压力测定的标准试验方法 Standard
Test Method of Rapid Pressure Determination
of Pressurized Products
ASTM D 3139-1998 使用挠性弹性密封件的塑料压力管用连接件标准规范 Standard
Specification for Joints for Plastic Pressure
Pipes Using Flexible Elastomeric Seals
ASTM D 3152-1972 用压力膜装置对细土壤的毛细管与水分之间关系的试验方法
Test Method for Capillary-Moisture Relationships
for Fine-Textured Soils by Pressure-Membrane
Apparatus
ASTM D 323-2006 石油产品蒸气压力的标准测试方法(Reid法) Standard
Test Method for Vapor Pressure of Petroleum
Products (Reid Method)
ASTM D 3291-1997 压力作用下聚氯乙烯塑料中增塑剂的兼容性 Standard
Practice for Compatibility of Plasticizers in
Poly(Vinyl Chloride) Plastics Under Compression
ASTM D 3517-2006 玻璃纤维增强热固性树脂压力管的标准规范 Standard
Specification for "Fiberglass" (Glass-Fiber-Reinforced
Thermosetting-Resin) Pressure Pipe
ASTM D 3754-2006 玻璃纤维增强热固性树脂污水压力管和工业压力管的标准规范
Standard Specification for "Fiberglass"
(Glass-Fiber-Reinforced Thermosetting-Resin)
Sewer and Industrial Pressure Pipe
ASTM D 3877-2002 土壤石灰混合物单向膨胀,收缩和隆起压力的标准试验方法
Standard Test Methods for One-Dimensional Expansion,
Shrinkage, and Uplift Pressure of Soil-Lime
Mixtures
ASTM D 3915-2006 压力设备用塑料管和配件用硬质聚氯乙烯(PVC)和氯化聚氯乙烯(CPVC)化合物的标准规范
Standard Specification for Rigid Poly(Vinyl
Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride)
(CPVC) Compounds for Plastic Pipe and Fittings
Used in Pressure Applications
ASTM D 3931a-1993 测定裂缝强度的标准试验方法.用压力负荷法测定填充胶粘剂的剪切
粘结强度 Standard Test Method for Determining Strength
of Gap-Filling Adhesive Bonds in Shear by Compression
Loading
ASTM D 4264-1990 室内储水管用橡胶衬里的消防软管和橡胶增强软管的组合件的压力试验方法
Test Method for Pressure Testing of Assemblies
of Rubber-Lined Fire Hose and Rubber Booster
Hose in Service on Interior Standpipes
ASTM D 454-2004 用加热及空气压力法测定橡胶变质的标准试验方法 Standard
Test Method for Rubber Deterioration by Heat
and Air Pressure
ASTM D 4631-1995 用压力脉冲技术现场测量低渗透性岩石的透射率和释水系数的标准试验方法
Standard Test Method for Determining Transmissivity
and Storativity of Low Permeability Rocks by
In Situ Measurements Using Pressure Pulse Technique
ASTM D 4719-2007 土壤中预打孔压力计测试的标准试验方法 Standard
Test Method for Prebored Pressuremeter Testing
in Soils
ASTM D 4953-2006 汽油和汽油元氧混合物蒸气压力的标准试验方法(干燥法)
Standard Test Method for Vapor Pressure of Gasoline
and Gasoline-Oxygenate Blends (Dry Method)
ASTM D 4970-2005 纺织纤维品的耐起球和其他相关表面变化的标准试验方法(马丁戴尔压力检验机法)
Standard Test Method for Pilling Resistance
and Other Related Surface Changes of Textile
Fabrics: Martindale Tester)
ASTM D 5190-2001 石油产品蒸气压力的标准试验方法(自动方法) Standard
Test Method for Vapor Pressure of Petroleum
Products (Automatic Method)
ASTM D 5191-2007 石油产品蒸气压力的标准试验方法(小型法) Standard
Test Method for Vapor Pressure of Petroleum
Products (Mini Method)
ASTM D 5224-2000 热固模制合成材料的压力模制试样的标准操作规程 Standard
Practice for Compression Molding Test Specimens
of Thermosetting Molding Compounds
ASTM D 5325-2003 测定水基型(压力罐装)喷雾涂料中挥发物重量百分比的标准试验方法
Standard Test Method for Determination of Weight
Percent Volatile Content of Water-Borne Aerosol
Paints
ASTM D 5385-1993 防水材料耐静水压力的试验方法 Test Method
for Hydrostatic Pressure Resistance of Waterproofing
Membranes
ASTM D 5482-2001 石油产品蒸气压力的标准试验方法(大气的小型法) Standard
Test Method for Vapor Pressure of Petroleum
Products (Mini Method-Atmospheric)
ASTM D 5685-2005 "玻璃纤维"(玻璃-纤维-增强热固树脂)压力管配件的标准规范
Standard Specification for "Fiberglass"
(Glass-Fiber-Reinforced Thermosetting-Resin)
Pressure Pipe Fittings
ASTM D 5720-1995 土工用电子传感器型压力测量系统静态校准标准规程 Standard
Practice for Static Calibration of Electronic
Transducer-Based Pressure Measurement Systems
for Geotechnical Purposes
ASTM D 6049-2003 通过平行板之间压力测定橡胶化合物和非含硫生橡胶黏性和弹性的橡胶特性的标准试验方法
Standard Test Method for Rubber Property - Measurement
of the Viscous and Elastic Behavior of Unvulcanized
Raw Rubbers and Rubber Compounds by Compression
Between Parallel Plates
ASTM D 6069-2001 通过氧化燃烧和还原压力化学发光检测法测定航空用碳氢化合物中痕量氮的标准试验方法
Standard Test Method for Trace Nitrogen in Aromatic
Hydrocarbons by Oxidative Combustion and Reduced
Pressure Chemiluminescence Detection
ASTM D 6377-2003 原油蒸气压力测定的标准试验方法:VPCRx(膨胀法)
Standard Test Method for Determination of Vapor
Pressure of Crude Oil: VPCRx (Expansion Method)
ASTM D 6378-2007 测定石油产品、烃和烃氧化剂混合物蒸气压力(VPX)的标准试验方法(三级膨胀法)
Standard Test Method for Determination of Vapor
Pressure (VPX) of Petroleum Products, Hydrocarbons,
and Hydrocarbon-Oxygenate Mixtures (Triple Expansion
Method)
ASTM D 6641-2001 用组合式荷载压力试验夹具测定聚合物基质复合叠材的压力特性的标准试验方法
Standard Test Method for Determining the Compressive
Properties of Polymer Matrix Composite Laminates
Using a Combined Loading Compression (CLC) Test
Fixture
ASTM D 6897a-2003 液化石油气蒸气压力的标准试验方法(膨胀法) Standard
Test Method for Vapor Pressure of Liquefied
Petroleum Gases (LPG) (Expansion Method)
ASTM D 7088-2004 砖石工程用地下设施涂层的抗流体静压力的标准规程 Standard
Practice for Resistance to Hydrostatic Pressure
for Coatings Used in Below Grade Applications
Applied to Masonry
ASTM D 7089-2006 用压力冲洗水泥、砖石和天然石料表面的除涂鸦的覆层有效性测定的标准实施规程
Standard Practice for Determination of the Effectiveness
of Anti-Graffiti Coating for Use on Concrete,
Masonry and Natural Stone Surfaces by Pressure
Washing
ASTM E 1005-2003 E706(ⅢA)反应堆压力容器监视用辐射测量监视器的应用和分析的标准试验方法
Standard Test Method for Application and Analysis
of Radiometric Monitors for Reactor Vessel Surveillance,
E 706(IIIA)
ASTM E 1139-2002 连续监测来自金属压力界面的声发射的标准实施规程 Standard
Practice for Continuous Monitoring of Acoustic
Emission from Metal Pressure Boundaries
ASTM E 1214-2006 使用反应堆堆芯压力容器监督用熔丝温度监视器的标准指南.E
706 (IIIE) Standard Guide for Use of Melt Wire
Temperature Monitors for Reactor Vessel Surveillance,
E 706 (IIIE)
ASTM E 1226-2005 可燃粉尘用压力和压力提高率的标准试验方法 Standard
Test Method for Pressure and Rate of Pressure
Rise for Combustible Dusts
ASTM E 1419b-2002 用声音排放法检验无缝、充气的压力容器的标准试验方法
Standard Test Method for Examination of Seamless,
Gas- Filled, Pressure Vessels Using Acoustic
Emission
ASTM E 1424-1991 在试样两侧特定压力和温度差下透过外窗,护墙和门的空气泄漏率的测定方法
Standard Test Method for Determining the Rate
of Air Leakage Through Exterior Windows, Curtain
Walls, and Doors Under Specified Pressure and
Temperature Differences Across the Specimen
ASTM E 1597-2005 海洋环境用光电组件的盐水压力浸渍试验和温度试验的标准试验方法
Standard Test Method for Saltwater Pressure
Immersion and Temperature Testing of Photovoltaic
Modules for Marine Environments
ASTM E 1719-2005 用沸点测定法测定液体蒸气压力的标准试验方法 Standard
Test Method for Vapor Pressure of Liquids by
Ebulliometry
ASTM E 1782-2003 用热分析法测定蒸气压力的标准试验方法 Standard
Test Method for Determining Vapor Pressure by
Thermal Analysis
ASTM E 1886-2005 受弹性体冲击以及循环压力差下外窗、幕墙、门和冲击保护系统性能的标准试验方法
Standard Test Method for Performance of Exterior
Windows, Curtain Walls, Doors, and Impact Protective
Systems Impacted by Missile(s) and Exposed to
Cyclic Pressure Differentials
ASTM E 1888/E 1888M-2007 带轻质木心由玻璃纤维增强塑料制成的压力容器声音发出检验用标准实施规程
Standard Practice for Acoustic Emission Examination
of Pressurized Containers Made of Fiberglass
Reinforced Plastic with Balsa Wood Cores
ASTM E 2071-2000 从蒸气压力数据中计算汽化热或蒸馏热的标准规程 Standard
Practice for Calculating Heat of Vaporization
or Sublimation from Vapor Pressure Data
ASTM E 2191-2002 利用声辐射检查充气的丝绕复合材料压力容器的标准试验方法
Standard Test Method for Examination of Gas-Filled
Filament-Wound Composite Pressure Vessels Using
Acoustic Emission
ASTM E 2223-2002 用斜束超声法检验无缝、充气钢制的压力容器的标准实施规程
Standard Practice for Examination of Seamless,
Gas-Filled, Steel Pressure Vessels Using Angle
Beam Ultrasonics
ASTM E 2581-2007 航天航空用聚合物基复合材料、夹层芯材和纤维缠绕压力容器的剪切测量技术的标准实施规程
Standard Practice for Shearography of Polymer
Matrix Composites, Sandwich Core Materials and
Filament-Wound Pressure Vessels in Aerospace
Applications
ASTM E 296-1970 用于空间模拟器的电离压力计的标准实施规程 Standard
Practice for Ionization Gage Application to
Space Simulators
ASTM E 482-2007 反应堆压力容器监视用中子输运法应用的标准指南.E706(IID)
Standard Guide for Application of Neutron Transport
Methods for Reactor Vessel Surveillance, E706
(IID)
ASTM E 636-2002 对E706(IH)核动力反应堆压力容器进行辅助监视试验的标准指南
Standard Guide for Conducting Supplemental Surveillance
Tests for Nuclear Power Reactor Vessels, E 706
(IH)
ASTM E 637-2005 通过临界点传热与压力的热传递理论和实验测量来计算临界热函的标准试验方法
Standard Test Method for Calculation of Stagnation
Enthalpy from Heat Transfer Theory and Experimental
Measurements of Stagnation-Point Heat Transfer
and Pressure
ASTM E 706-2002 E706(0)轻水反应堆压力容器监视标准的标准主模型 Standard
Master Matrix for Light-Water Reactor Pressure
Vessel Surveillance Standards, E706(0)
ASTM E 789-1995 1.2公升的密封圆筒形容器中粉尘爆炸产生压力以及压力升高的速率的标准测试方法
Standard Test Method for Dust Explosions in
a 1.2-Litre Closed Cylindrical Vessel
ASTM E 918-1983 温度和压力升高时化学药品易燃极限的测定 Determining
Limits of Flammability of Chemicals at Elevated
Temperature and Pressure
ASTM F 1025-1994 用于增强或修复聚乙烯煤气压力管上爆裂或破洞的全环绕型带夹紧装置的选择和使用
Standard Guide for Selection and Use of Full-Encirclement-Type
Band Clamps for Reinforcement or Repair of Punctures
or Holes in Polyethylene Gas Pressure Pipe
ASTM F 1041-2002 聚烯烃燃气压力管和管道的燃气排除的标准指南 Standard
Guide for Squeeze-Off of Polyolefin Gas Pressure
Pipe and Tubing
ASTM F 1112a-2006 静态测试无内胎充气轮胎的充气压力损耗率的标准试验方法
Standard Test Method for Static Testing of Tubeless
Pneumatic Tires for Rate of Loss of Inflation
Pressure
ASTM F 1176-2001 最大工作压力为125psi的地下热塑灌溉系统设计和安装的标准实施规程
Standard Practice for Design and Installation
of Underground Thermoplastic Irrigation Systems
With Maximum Working Pressure of 125 psi
ASTM F 1199-1988 铸造(各种温度及各种压力)和焊接管道过滤器(最大表压为150磅/英寸及最大温度150华氏度)
Standard Specification for Cast (All Temperatures
and Pressures) and Welded Pipe Line Strainers
(150 psig and 150°F Maximum)
ASTM F 1281-2007 交联聚乙烯/铝/交联聚乙烯(PEX-AL-PEX)压力管的标准规范
Standard Specification for Crosslinked Polyethylene/Aluminum/Crosslinked
Polyethylene (PEX-AL-PEX) Pressure Pipe
ASTM F 1282-2006 聚乙烯/铝/聚乙烯(PE-AL-PE)复合材料压力管的标准规范
Standard Specification for Polyethylene/Aluminum/Polyethylene
(PE-AL-PE) Composite Pressure Pipe
ASTM F 1335-2004 高温设备用标定压力的复合管道及其配件标准规范 Standard
Specification for Pressure-Rated Composite Pipe
and Fittings for Elevated Temperature Service
ASTM F 1483-2005 定向聚氯乙烯(PVCO)压力管的标准规范 Standard
Specification for Oriented Poly(Vinyl Chloride),
PVCO, Pressure Pipe
ASTM F 1819-2007 使用机械压力技术通过合成血液对防护服用抗渗透材料的标准试验方法
Standard Test Method for Resistance of Materials
Used in Protective Clothing to Penetration by
Synthetic Blood Using a Mechanical Pressure
Technique
ASTM F 1964-1999 压力油炸器和锅状油炸器性能的标准试验方法 Standard
Test Method for Performance of Pressure and
Kettle Fryers
ASTM F 1974-2004 聚乙烯/铝/聚乙烯和交联聚乙烯/铝/交联聚乙烯复合压力管用金属内插配件标准规范
Standard Specification for Metal Insert Fittings
for Polyethylene/Aluminum/Polyethylene and Crosslinked
Polyethylene/Aluminum/Crosslinked Polyethylene
Composite Pressure Pipe
ASTM F 2070-2000 压力和差动压力电及光纤换能器标准规范 Standard
Specification for Transducers, Pressure and
Differential, Pressure, Electrical and Fiber-Optic
ASTM F 2164-2002 使用静液压的聚乙烯压力管道系统的现场泄漏试验的标准实施规范
Standard Practice for Field Leak Testing of
Polyethylene (PE) Pressure Piping Systems Using
Hydrostatic Pressure
ASTM F 2231-2002 压力管道用聚乙烯薄样品的却贝冲击试验的标准试验方法 Standard
Test Method for Charpy Impact Test on Thin Specimens
of Polyethylene Used in Pressurized Pipes
ASTM F 2261-2006 表40～80额定压力氯乙烯(PVC)塑料管配件的标准试验方法
Standard Test Method for Pressure Rating Poly(Vinyl
Chloride) (PVC) Plastic Pipe Fittings, Schedule
40 and 80 Socket-Type
ASTM F 2389-2007 压力标定的聚丙烯(PP)管道系统标准规范 Standard
Specification for Pressure-rated Polypropylene
(PP) Piping Systems
ASTM F 2467-2006 运输用途中用压力指片(PIF)测量静态密封压力的标准实施规程
Standard Practice for Measuring Static Sealing
Pressure Using Pressure-Indicating Film (PIF)
in Transportation Applications
ASTM F 2528-2006 带压力气囊的肠给食装置标准试验方法 Standard
Test Methods for Enteral Feeding Devices with
a Retention Balloon
ASTM F 2562/F 2562M-2007 非压力排水和排污用增强钢热塑加肋管及其配件的标准规范
Standard Specification for Steel Reinforced
Thermoplastic Ribbed Pipe and Fittings for Non-Pressure
Drainage and Sewerage
ASTM F 2569-2007 体育运动用表面压力还原性能评估的标准试验方法 Standard
Test Method for Evaluating the Force Reduction
Properties of Surfaces for Athletic Use
ASTM F 689-1997 有金属套管的地上塑料气体压力管的温度测定 Standard
Practice for Determination of the Temperature
of Above-Ground Plastic Gas Pressure Pipe Within
Metallic Casings
ASTM F 690-1986 热塑性压力管道灌溉系统的地下安装标准规程 Standard
Practice for Underground Installation of Thermoplastic
Pressure Piping Irrigation Systems
ASTM F 948-1994 在恒定内流动压力下塑料管道系统和组件损坏时间的标准试验方法
Standard Test Method for Time-to-Failure of
Plastic Piping Systems and Components Under
Constant Internal Pressure With Flow
ASTM/ISO 10079-3-1999 医疗抽吸设备.第3部分:真空或压力抽吸设备
Medical Suction Equipment - Part 3: Suction
Equipment Powered from a Vacuum or Pressure
Source
UL 10C-1998 门组件的正压力燃烧试验 (Positive pressure fire
tests of door assemblies )
UL 136-2002 压力锅 (Pressure cookers )
UL 1468-1995 防火设备用直接控制的减压阀和压力控制阀 (Direct acting
pressure reducing and pressure restricting valves
)
UL 1713-2001 地下消防设备用玻璃纤维增强压力管道和管联接器 (Pressure
pipe and couplings, glass fiber-reinforced,
for underground fire service )
UL 1739-1994 消防设备用液压控制的压力控制阀 (Pilot-operated
pressure-control valves for fire-protection
service )
UL 194-1996 防火用球墨铸铁和灰铸铁压力管和配件加垫圈的接头 (Gasketed
joints for ductile-iron pipe and fittings for
fire protection service )
UL 393-1996 消防设备用压力指示计 (Indicating pressure
gauges for fire-protection service )
UL 404-1997 压缩煤气设备用压力指示计 (Gauges, indicating
pressure, for compressed gas service )
UL 745-2-32-1995 磁力钻床压力机特殊要求 (Particular requirements
for magnetic drill presses )
英国压力标准(BS pressure standards)
--------------------------------------------------------------------------------
编号 中文名称 英文名称
BIP 3055-2005 工作场所压力.实况.DVD Stress in the workplace
- The facts - DVD
BS 1101-1977 涂料和其他类似物质用压力容器规范 Specification
for pressure containers for paint and other
similar substances
BS 1377-6-1990 土木工程用土壤试验方法.第6部分:在液压压力盒内并且用孔隙压力测量进行固结和渗透率试验
Methods of test for soils for civil engineering
purposes - Consolidation and permeability tests
in hydraulic cells and with pore pressure measurement
BS 1428-D1-1965 微量化学仪器.第D 集:容量分析仪器.第1部分:带压力加注装置和自动回零的滴定管规范
Microchemical apparatus - Volumetric analysis
- Specification for burettes with pressure-filling
device and automatic zero
BS 1552-1995 压力可达200毫巴家庭用一类、二类和三类燃气敞口底部锥形旋塞阀规范
Specification for open bottomed taper plug valves
for 1st, 2nd and 3rd family gases up to 200
mbar
BS 1726-1-2002 用圆形线材和棒材制的圆柱形螺旋弹簧.规格、公差和测试指南.压力弹簧
Cylindrical helical springs made from round
wire and bar - Guide to methods of specifying,
tolerances and testing - Compression springs
BS 2000-0-0.4-1996 气压计压力校正 Barometric pressure
corrections
BS 2000-121-2005 石油及其产品的试验方法.从润滑脂中分离油的测定.压力过滤法
Methods of test for petroleum and its products
- Part 121: Determination of oil separation
from lubricating grease - Pressure filtration
method (Identical with IP 121:2005)
BS 2782-11 Method 1121B-1997 塑料的试验方法.第11部分:热塑管、接头和阀门.流体输送用热塑管.试验方法1121B:额定外部直径和额定压力.米
Methods of testing plastics - Thermoplastics
pipes, fittings and valves - Thermoplastics
pipes for the conveyance of fluids - Nominal
outside diameters and nominal pressures - Metric
series
BS 2782-11 Method 1121C-1997 塑料试验方法.第11部分:热塑管、接头和阀门.流体输送用热塑管.试验方法1121C:额定外部直径和额定压力.英尺
Methods of testing plastics - Thermoplastics
pipes, fittings and valves - Thermoplastics
pipes for the conveyance of fluids - Nominal
outside diameters and nominal pressures - Inch-based
series
BS 2782-11 Method 1127P-1997 塑料试验方法.第11部分:热塑管,接头和阀门.液体输送用热塑材管.试验方法1127P:抗内压力.试验方法
Methods of testing plastics - Thermoplastics
pipes, fittings and valves - Thermoplastics
pipes, for the conveyance of fluids - Resistance
to internal pressure - Test method
BS 2782-8 Method 821A-1979 塑料的试验方法.第8部分:其他性能.试验方法821A:在大气压力条件下薄片和薄膜透气率的测定(压力计)
Methods of testing plastics. Other properties.
Determination of the gas transmission rate of
films and thin sheets under atmospheric pressure
(manometric method)
BS 2C 11-1988 航空用压力舱的地面压力试验连接件规范 Specification
for ground pressure test connections for aircraft
pressure cabins
BS 2C 19-1994 新型压力重上油连接器规范 Specification for
pressure re-oiling connection (new type)
BS 2C 4-1973 飞机发动机制冷剂压力灌注接头尺寸规范 Specification
for coupling dimensions for aero-engine refrigerant
pressure replenishment connections
BS 2G 113-1956 飞行器用进气管压力表规范 Specification for
manifold pressure gauges for aircraft
BS 2G 117-1975 压力驱动空速指示器规范 Specification for
pressure-driven airspeed indicators
BS 2G 182-1975 航空用压力驱动马赫表规范 Specification for
pressure-driven machmeters for aircraft
BS 2G 201-1996 计数器和指示器压力高度计规范 Specification
for counter and pointer pressure altimeters
BS 3166-1959 温度范围为-20-220°F(-30-105℃)用温度记录器(注入液体型与蒸汽压力型)规范
Specification for thermographs (liquid-filled
and vapour pressure types) for use within the
temperature range -20 °F to 220 °F ( -30 °C
to 105 °C)
BS 3321-1986 织物的等效孔径测量方法(气泡压力试验) Method for
measurement of the equivalent pore size of fabrics
(bubble pressure test)
BS 3463-1975 压力容器水位观察和玻璃量杯规范 Specification for
observation and gauge glasses for pressure vessels
BS 3900-A22-1998 涂料的试验方法.第A22部分：用压力杯法对密度的测定
Methods of test for paints. Determination of
density by the pressure cup method
BS 3G 100-2.3.2-1970 飞机设备一般要求规范.第2部分:各种设备.第3节:环境条件.第2小节:温度压力要求
Specification for general requirements for equipment
for use in aircraft - All equipment - Environmental
conditions - Temperature-pressure requirements
BS 4151-1967 输入信号为 3至15磅/平方英寸(压力计)的气动阀定位器的评定方法
Method of evaluating pneumatic valve positioners
with input signal of 3 to 15 lbf/in2 (gauge)
BS 4172-1-1999 消灭室内飞虫用手持式压力气溶喷洒器.杀虫性能规范 Hand-held
pressurized aerosol dispensers against houseflies
- Specification for insecticidal performance
BS 4172-2-1999 消灭室内飞虫用手持式压力气溶喷洒器.杀虫性能的测定方法 Hand-held
pressurized aerosol dispensers against houseflies
- Method for determination of insecticidal performance
BS 4184-1994 开式机械型机动压力机词汇 Glossary for power
presses, open front mechanical type
BS 4346-3-1982 未增塑聚氯乙烯压力管的接头及配件.第3部分:溶粘剂规范 Joints
and fittings for use with unplasticized PVC
pressure pipes - Specification for solvent cement
BS 4361-30-1990 木工机械.第30部分:平滑表面手工上料平面胶合压力机命名
Woodworking machines - Nomenclature for hand-loading
veneering presses for flat surfaces
BS 4656-34-1985 机床精度及试验方法.第34部分:机械的开式机动压力机规范
Accuracy of machine tools and methods of test
- Specification for power presses, mechanical
open front type
BS 470-1984 压力容器检验孔、观察孔和入口孔规范 Specification
for inspection, access and entry openings for
pressure vessels
BS 4737-3.9-1978 擅入者报警系统规范.第3部分:元部件规范.第9节:压力传感垫
Intruder alarm systems - Specifications for
components - Pressure mats
BS 4742-3-1985 农用机械液压设备.第3部分:挂车用单动倾卸伸缩筒尺寸和额定压力规范
Hydraulic equipment for agricultural machinery
- Specification for dimensions and pressure
rating of single-acting telescopic tipping cylinders
for trailers
BS 4882-1990 法兰和保持压力用螺栓连接规范 Specification for
bolting for flanges and pressure containing
purposes
BS 4975-1990 核工程用预应力混凝土压力容器规范 Specification
for prestressed concrete pressure vessels for
nuclear engineering
BS 4C 14-1991 航空用压力加油连接器规范 Specification for
aircraft pressure refuelling connectors
BS 5045-8-2000 可运输的气瓶.特殊便携的在15℃时最高达300巴充气压力的水容量为0.5L-15L的无缝铝合金气瓶规范
Transportable gas containers - Specification
for seamless aluminium alloy gas containers
of water capacity 0.5 L up to 15 L and up to
300 bar charged pressure at 15 °C for special
portable application
BS 5173-102.8-1987 橡胶和塑料软管及软管组件试验方法.第102部分:液压试验.第8节:硬质增强热塑性塑料螺旋管压力脉冲试验
Methods of test for rubber and plastics hoses
and hose assemblies - Hydraulic pressure tests
- Pressure impulse test for rigid helix reinforced
thermoplastics hoses
BS 5276-1-1984 压力容器详细规格(尺寸).第1部分:钢容器支管盖吊杆规范
Pressure vessel details (dimensions) - Specification
for davits for branch covers of steel vessels
BS 5276-2-2003 压力容器细则(尺寸).卧式圆柱形压力容器鞍式支座规范 Pressure
vessel details (dimensions) - Specification
for saddle supports for horizontal cylindrical
pressure vessels
BS 5276-4-1977 压力容器详细规格(尺寸).第4部分:标准化压力容器 Pressure
vessel details (dimensions) - Standardized pressure
vessels
BS 5391-1-2006 丙烯腈-丁二烯-苯乙烯(ABS)压力管.规范 Acrylonitrile-butadiene-styrene
(ABS) pressure pipe - Specification
BS 5392-1-2006 用于丙烯腈-丁二烯-苯乙烯共聚物(ABS)压力管道的ABS配件.第1部分:规范
Acrylonitrile-butadiene-styrene (ABS) fittings
for use with ABS pressure pipe - Part 1: Specification
BS 5677-1979 采用互易技术对1英寸标准电容式传声器进行压力校准的精确方法 Method
(precision) for pressure calibration of one-inch
standard condenser microphones by the reciprocity
technique
BS 5886-1980 石棉水泥管路的现场压力试验方法 Methods for field
pressure testing of asbestos-cement pipelines
BS 5911-5-2004 混凝土管和辅助混凝土制品.带软接头的预应力非压力管道和配件的规范
Concrete pipes and ancillary concrete products
- Specification for prestressed non-pressure
pipes and fittings with flexible joints
BS 5944-4-1984 液压动力系统和部件空气噪音测量.第4部分:流量和压力控制阀声功率级测定方法
Measurement of airborne noise from hydraulic
fluid power systems and components - Method
of determining sound power levels from valves
controlling flow and pressure
BS 6069-5.1-1994 空气质量表征.第5部分:总则.第1节:温度、压力和湿度数据处理
Characterization of air quality - General -
Handling of temperature, pressure and humidity
data
BS 6129-1-1981 压力系统用波纹管膨胀节选用惯例.第1部分:金属波纹管膨胀节
Code of practice for the selection and application
of bellows expansion joints for use in pressure
systems - Metallic bellows expansion joints
BS 6134-1992 压力和真空开关规范 Specification for pressure
and vacuum switches
BS 6282-2-1982 防止回流水污染用带动件装置.第2部分:公称尺寸小于等于DN54的终端反压力阀规范
Devices with moving parts for the prevention
of contamination of water by backflow - Specification
for terminal anti-vacuum valves of nominal size
up to and including DN 54
BS 6282-4-1982 防止回流水污染用带动件装置.第4部分:公称尺寸小于等于DN42的组合单向阀和反压力阀规范
Devices with moving parts for the prevention
of contamination of water by backflow - Specification
for combined check and anti-vacuum valves of
nominal size up to and including DN 42
BS 6283-2-1991 热水系统安全控制装置.第2部分:压力范围从1bar到10bar的温度减压阀规范
Safety and control devices for use in hot water
systems - Specifications for temperature relief
valves for pressures from 1 bar to 10 bar
BS 6283-4-1991 热水系统中安全控制装置.第4部分:最大供给压力不超过12bar、标准尺寸不超过DN50的放松减压阀规范
Safety and control devices for use in hot water
systems - Specification for drop-tight pressure
reducing valves of nominal size up to and including
DN 50 for supply pressures up to and including
12 bar
BS 6356-2-1985 农作物防护用喷雾设备.第2部分:喷嘴与压力计连接尺寸规范
Spraying equipment for crop protection - Specification
for connecting dimensions for nozzles and manometers
BS 6400-2-2006 最大容量不超过6m<上标>3/h煤气表的安装、调换、重新定位和拆除用规范.中等压力(二类家用煤气)
Specification for installation, exchange, relocation
and removal of gas meters with a maximum capacity
not exceeding 6 m3/h - Medium pressure (2nd
family gases)
BS 6447-1984 输出电量的绝对压力发送器与表压发送器规范 Specification
for absolute and gauge pressure transmitters
with electrical outputs
BS 6448-1995 DN大于50的燃气调节器和进气口压力可达200mbar规范 Specification
for gas appliance governors of DN greater than
50 and for inlet pressures up to 200 mbar
BS 6590-1985 机械的开式压力机的额定功率和尺寸规范 Specification
for capacity ratings and dimensions of power
presses, mechanical open front type
BS 6944-1988 黑色金属(不包括压力管应用的)闪光对接焊规范 Specification
for flash welding of butt joints in ferrous
metals (excluding pressure piping applications)
BS 6979-1989 机动压力机的静载挠度的测量方法 Method for measurement
of static deflection of power presses
BS 7005-1988 蒸汽压缩致冷系统用碳钢非用火压力容器的设计和制造规范 Specification
for design and manufacture of carbon steel unfired
pressure vessels for use in vapour compression
refrigeration systems
BS 7068-1989 交变压力气垫规范 Specification for alternating
pressure air mattresses
BS 7372-3-1993 工业金属丝筛网和金属丝编织布孔径和丝径组合选择指南.第3部分:预压接或压力焊接金属丝筛网的优选组合
Guide to the choice of aperture size and wire
diameter combinations for industrial wire screens
and woven wire cloth - Preferred combinations
for pre-crimped or pressure-welded wire screens
BS 7403-1-1998 内燃机满液流润滑油过滤器.不同压力/流量特性试验方法 Full-flow
lubricating oil filters for internal combustion
engines - Methods of test for differential pressure/flow
characteristics
BS 7403-6-1991 内燃机用全流式润滑油过滤器.第6部分:静态爆裂压力的试验方法
Full-flow lubricating oil filters for internal
combustion engines - Method of test for static
burst pressure
BS 7504-1995 液压流体动力.在压力25 MPa 和40 MPa(250 巴
和400 巴)条件下使用的四螺钉、单片正方形法兰连接器 Hydraulic fluid
power - Four-screw, one-piece square flange
connections for use at pressures of 25 MPa and
40 MPa (250 bar and 400 bar)
BS 7527-2.3-1991 环境条件分类.第2部分:大自然呈现的环境条件.第3节:大气压力
Classification of environmental conditions -
Environmental conditions appearing in nature
- Air pressure
BS 7568-12-1992 冲压工具.第12部分:弹性体压力弹簧一般规范 Press
tools - Elastomer pressure springs - General
specification
BS 7568-13-1992 冲压工具.第13部分:弹性体压力弹簧.附件规范 Press
tools - Elastomer pressure springs - Specification
of accessories
BS 7707-1993 400kN-4000kN(含40000kN)公称力机械直边单作用型机动压力机规范
Specification for power presses, mechanical
straight-sided single-action type from 400 kN
up to and including 4000 kN nominal force
BS 7708-1993 250kN-400kN公称力的机械直边高速型机动压力机规范 Specification
for power presses, mechanical straight-sided
high-speed type of 250 kN up to 4000 kN nominal
force
BS 7727-1994 铜导体面积达6平方毫米(10AWG)电缆的预绝缘压力终端和连接器的安装和检测实用规程
Code of practice for installation and inspection
of pre-insulated compression terminals and connectors
for cables with copper conductors up to 6 mm2
BS 7847-1996 流体动力系统和部件.连接件和相关部件.标称压力 Fluid power
systems and components - Connectors and associated
components - Nominal pressures
BS 853-2-1996 供暖系统用压力容器规范.第2部分:建筑业和工业设施用管式热交换器和蓄热器
Specification for vessels for use in heating
systems - Tubular heat exchangers and storage
vessels for building and industrial services
BS AU 163a-1985 道路车辆用气压制动设备压力试验连接规范 Specification
for pressure test connection for compressed-air
pneumatic braking equipment for road vehicles
BS AU 50-3.1e-2002 轮胎和车轮.阀门.尺寸、名称与符号、使用中阀门压力等级和夹紧阀门扭矩
Tyres and wheels - Valves - Dimensions, designation,
valve pressure ratings by use and torque for
clamp-in valves
BS DD CEN/TS 13244-7-2004 排水和污水处理通用地下和地上压力设备用塑料管道系统.聚乙烯(PE).符合性评定指南
Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
Guidance for the assessment of conformity
BS DD CEN/TS 14541-2007 非压力设备用塑料管道和配件.非原态未增塑聚氯乙烯、聚丙烯和聚乙烯材料应用
Plastics pipes and fittings for non-pressure
applications - Utilisation of non-virgin PVC-U,
PP and PE materials
BS DD CEN/TS 1456-2-2003 压力下直埋式和地上排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U).合格评定指南
Plastic piping systems for buried and above-ground
drainage and sewerage under pressure - Unplasticized
poly(vinyl chloride) (PVC-U) - Guidance for
the assessment of conformity
BS DD CEN/TS 14632-2006 排水、排污和供水、压力和非压力用塑料管道系统.基于聚酯树脂(UP)玻璃纤维增强热固性塑料(GPR).合格评定指
Plastics piping systems for drainage, sewerage
and water supply, pressure and non-pressure
- Glass-reinforced thermosetting plastics (GRP)
based on polyester resin (UP) - Guidance for
the assessment of conformity
BS DD CEN/TS 14758-3-2006 无压力地下排水和排污塑料管道系统.聚丙烯矿物调节器(s)(PP-MD).安装指南
Plastics piping systems for non-pressure underground
drainage and sewerage - Polypropylene with mineral
modifier(s)(PP-MD) - Guidance for installation
BS DD CEN/TS 1591-4-2007 法兰及其连接件.带垫圈圆形法兰连接件的设计原则.符合压力设备指令的螺栓连接件装配职工能力的合格鉴定
Flanges and their joints - Design rules for
gasketed circular flange connections - Qualification
of personnel competency in the assembly of bolted
joints fitted to equipment subject to the Pressure
Equipment Directive
BS DD CEN/TS 1852-3-2003 非压力地下排水和排污塑料管道系统.聚丙烯(PP).安装指南
Plastics piping systems for non-pressure underground
drainage and sewerage - Polypropylene (PP) -
Guidance for installation
BS DD CEN/TS 764-6-2004 压力设备.操作说明书的结构和内容 Pressure
equipment - Structure and content of operating
instructions
BS DD ENV 12108-2001 塑料管道系统.建筑物内部人消费用冷热水的压力系统的安装指南
Plastics piping systems - Guidance for the installation
inside buildings of pressure systems for hot
and cold water intended for human consumption
BS DD ENV 13050-2001 幕墙.水密封性.空气压力和水喷射动态条件下的实验室试验
Curtain walling - Watertightness - Laboratory
test under dynamic condition of air pressure
and water spray
BS DD ISO/TS 17996-2006 乳酪.以恒定位移速率的单轴压力测定流变特性
Cheese - Determination of rheological properties
by uniaxial compression at constant displacement
rate
BS EN 10028-1-2000 压力容器用的钢板制品规范.一般要求 Specification
for flat products made of steels for pressure
purposes - General requirements
BS EN 10028-3-2003 压力容器用的扁平钢轧材规范.经正火处理的可焊细粒钢
Specification for flat products made of steels
for pressure purposes - Weldable fine grain
steels, normalized
BS EN 10028-5-2003 压力容器用的扁平钢轧材规范.热机轧制可焊细粒钢 Specification
for flat products made of steels for pressure
purposes - Weldable fine grain steels, thermomechanically
rolled
BS EN 10028-6-2003 压力用的扁平钢轧材规范.淬火和回火可焊细粒钢 Specification
for flat products made of steels for pressure
purposes - Weldable fine grain steels, quenched
and tempered
BS EN 10028-7-2000 承受压力用的平钢板制品规范.不锈钢 Flat products
made of steels for pressure purposes - Stainless
steels
BS EN 10207-2005 简单压力容器用钢材.板材、带材和棒材交货技术要求 Steels
for simple pressure vessels - Technical delivery
requirements for plates, strips and bars
BS EN 10213-1-1996 压力用途的钢铸件交付技术状态.总则 Technical
delivery conditions for steel castings for pressure
purposes - General
BS EN 10213-2-1996 压力用途的钢铸件的交付技术状态.第2部分:环境温度和高温下使用钢的等级
Technical delivery conditions for steel castings
for pressure purposes - Steel grades for use
at room temperature and at elevated temperature
BS EN 10213-3-1996 压力用途的钢铸件交付技术状态.低温下使用的钢 Technical
delivery conditions for steel castings for pressure
purposes - Steels for use at low temperatures
BS EN 10213-4-1996 压力用途的钢铸件的交付技术状态.第4部分:奥氏体钢和奥氏体-铁素体钢的等级
Technical delivery conditions for steel castings
for pressure purposes - Austenitic and austenitic-ferritic
steel grades
BS EN 10216-5-2004 压力无缝钢管.交货技术条件.无缝钢管 Seamless
steel tubes for pressure purposes - Technical
delivery conditions - Stainless steel tubes
BS EN 10217-7-2005 压力用途焊接钢管.交货技术条件.不锈钢管 Welded
steel tubes for pressure purposes - Technical
delivery conditions - Stainless steel tubes
BS EN 10222-2-2000 压力容器用钢锻件.具有规定升温特性的铁素体钢和马口铁钢
Steel forgings for pressure purposes - Ferritic
and martensitic steels with specified elevated
temperature properties
BS EN 10222-3-1999 压力容器用钢锻件.具有特定低温特性的镍钢 Steel
forgings for pressure purposes - Nickel steels
with specified low-temperature properties
BS EN 10222-4-1999 压力容器用钢锻件.具有高验收强度的可焊接细晶粒钢
Steel forgings for pressure purposes - Weldable
fine-grain steels with high proof strength
BS EN 10222-5-2000 压力容器用钢锻件.马口铁钢,奥氏体钢,奥氏体-铁素体不锈钢
Steel forgings for pressure purposes - Martensitic,
austenitic and austenitic-ferritic stainless
steels
BS EN 10226-1-2004 螺纹上有压力密封接缝的管螺纹.锥形外螺纹和平行内螺纹.尺寸、公差及名称与符号
Pipe threads where pressure tight joints are
made on the threads - Taper external threads
and parallel internal threads - Dimensions,
tolerances and designation
BS EN 10226-2-2005 螺纹上压力强密联接的管螺纹.第2部分:锥形外螺纹和锥形内螺纹.尺寸、公差及名称和符号
Pipe threads where pressure tight joints are
made on the threads - Part 2: Taper external
threads and taper internal threads - Dimensions,
tolerances and designation
BS EN 10226-3-2005 螺纹上有压力密封接缝的管螺纹.用极限量规验证 Pipe
threads where pressure-tight joints are made
on the threads - Verification by means of limit
gauges
BS EN 10243-1-1999 钢模锻.公差和尺寸.落锤或垂直压力锻造 Steel
die forgings - Tolerances on dimensions - Drop
and vertical press forgings
BS EN 10273-2000 特定高温性能压力用热轧可焊接钢棒 Hot rolled
weldable steel bars for pressure purposes with
specified elevated temperature properties
BS EN 1053-1996 塑料管道系统.无压力情况下使用的热塑管道系统.防水性的检验方法
Plastics piping systems - Thermoplastics piping
systems for non-pressure applications - Test
methods for watertightness
BS EN 12007-1-2000 燃气供应系统.最大工作压力达到和超过16巴的管线.通用功能推荐值
Gas supply systems - Pipelines for maximum operating
pressure up to and including 16 bar - General
functional recommendations
BS EN 12007-2-2000 燃气供应系统.最大工作压力达到和超过16巴的管线.聚乙烯特定功能推荐值
Gas supply systems - Pipelines for maximum operating
pressure up to and including 16 bar - Specific
functional recommendations for polyethylene
(MOP up to and including 10 bar)
BS EN 12007-3-2000 燃气供应系统.最大工作压力达到和超过16巴的管线.钢特定功能推荐值
Gas supply systems - Pipelines for maximum operating
pressure up to and including 16 bar - Specific
functional recommendations for steel
BS EN 12007-4-2000 燃气供应系统.最大工作压力达到和超过16巴的管线.修复的特定功能推荐值
Gas supply systems - Pipelines for maximum operating
pressure up to and including 16 bar - Specific
functional recommendations for renovation
BS EN 12046-2-2000 操作压力.试验方法.门 Operating forces
- Test method - Doors
BS EN 12094-10-2003 固定消防系统.气体灭火系统元件.压力计和压力开关的试验方法和要求
Fixed firefighting systems - Components for
gas extinguishing systems - Requirements and
test methods for pressure gauges and pressure
switches
BS EN 12106-1998 塑料管道系统.聚乙稀(PE)阀门.挤压后抗内压力的试验方法
Plastics piping systems - Polyethylene (PE)
pipes - Test method for the resistance to internal
pressure after application of squeeze-off
BS EN 12155-2000 幕墙.水密性.静态压力下的实验室试验 Curtain
walling - Watertightness - Laboratory test under
static pressure
BS EN 12266-1-2003 工业用阀门.阀门试验.压力试验、试验规程和验收标准.强制要求
Industrial valves - Testing of valves - Pressure
tests, test procedures and acceptance criteria
- Mandatory requirements
BS EN 1229-1997 塑料管道系统.玻璃增强的热固性塑料管.验证短期内部压力下墙的密封性试验方法
Plastics piping systems - Glass-reinforced thermosetting
plastics (GRP) pipes and fittings - Test methods
to prove the leaktightness of the wall under
short-term internal pressure
BS EN 12291-2004 高级工业陶瓷.大气压力下高温空气中陶瓷复合材料的机械性能.压缩特性的测定
Advanced technical ceramics - Mechanical properties
of ceramic composites at high temperature in
air at atmospheric pressure - Determination
of compression properties
BS EN 12295-2000 塑料管道系统.热水和冷水用热塑管和附属配件.连接件耐压力变化的试验方法
Plastics piping systems - Thermoplastics pipes
and associated fittings for hot and cold water
- Test method for resistance of joints to pressure
cycling
BS EN 12327-2000 燃气供应系统.压力试验,交付使用和非交付使用过程.功能要求
Gas supply systems - Pressure testing, commissioning
and decommissioning procedures - Functional
requirements
BS EN 12350-7-2000 新浇混凝土试验.空气含量.压力法 Testing
fresh concrete - Air content - Pressure methods
BS EN 12365-2-2003 建筑五金.门、窗、百叶窗和幕墙用衬垫及挡风雨条.线性压力试验方法
Building hardware - Gasket and weatherstripping
for doors, windows, shutters and curtain walling
- Linear compression force test methods
BS EN 12392-2000 铝和铝合金.锻压产品.生产压力设备用产品专门要求 Aluminium
and aluminium alloys - Wrought products - Special
requirements for products intended for the production
of pressure equipment
BS EN 1254-4-1998 铜和铜合金.管路接头.与带有毛细管或压力端头的其它端头连接的管接头
Copper and copper alloys - Plumbing fittings
- Fittings combining other end connections with
capillary or compression ends
BS EN 12541-2003 卫生设备配件.压力冲洗阀和自动关闭便池冲水阀PN10
Sanitary tapware - Pressure flushing valves
and automatic closing urinal valves PN 10
BS EN 12561-3-2003 铁路设施.油罐车.压力下液化气用底部装卸装置 Railway
applications - Tank wagons - Bottom filling
and emptying devices for gases liquefied under
pressure
BS EN 12621-2006 压力下覆层材料的供应和循环用机器.安全要求 Machinery
for the supply and circulation of coating materials
under pressure - Safety requirements
BS EN 12645-1999 压力量规.机动车轮胎膨胀和/或压力检验设备.计量学,要求和试验
Pressure gauges - Apparatus for inspection of
pressure and/or inflation of tyres for motor
vehicles - Metrology, requirements and testing
BS EN 12666-1-2005 无压力地下排水和排污塑料管道系统.聚乙烯(PE).管、管件和系统的规范
Plastics piping systems for non-pressure underground
drainage and sewerage - Polyethylene (PE) -
Part 1: Specifications for pipes, fittings and
the system
BS EN 12697-25-2005 沥青混合料.热混沥青的试验方法.循环压力试验 Bituminous
mixtures - Test methods for hot mix asphalt
- Cyclic compression test
BS EN 12778-2002 烹饪器具.家用压力锅 Cookware - Pressure
cookers for domestic use
BS EN 12864-2001 丁烷、丙烷或其混合物用最大出口压力≤200mbar、液流量≤4kg/h的低压不可调的调节器及其相关的安全装置
Low-pressure, non adjustable regulators having
a maximum outlet pressure of less than or equal
to 200 mbar, with a capacity of less than or
equal to 4 kg/h, and their associated safety
devices for butane, propane or their mixtures
BS EN 12865-2001 建筑构件和建筑元件的湿温性能.在空气辅助压力下外墙抗暴雨力的测定
Hygrothermal performance of building components
and building elements - Determination of the
resistance of external wall systems to driving
rain under pulsating air pressure
BS EN 12952-2-2002 水管锅炉和辅助设备.第2部分:锅炉和附件的压力零件用材料
Water-tube boilers and auxiliary installations
- Materials for pressure parts of boilers and
accessories
BS EN 12952-3-2002 水管锅炉和辅助设备.压力零件的设计和计算 Water-tube
boilers and auxiliary installations - Design
and calculation of pressure parts
BS EN 12952-5-2002 水管锅炉和辅助设备.第5部分:锅炉压力部件的工艺和制造
Water-tube boilers and auxiliary installations
- Workmanship and construction of pressure parts
of the boiler
BS EN 12952-6-2002 水管锅炉和辅助设备.锅炉压力部件在生产过程中的检验,文献工作和作标记
Water-tube boilers and auxiliary installations
- Inspection during construction, documentation
and marking of pressure parts of the boiler
BS EN 12953-2-2002 火管锅炉.锅炉和附件用的压力零件材料 Shell
boilers - Materials for pressure parts of boilers
and accessories
BS EN 12953-3-2002 火管锅炉.压力零件的设计和计算 Shell boilers
- Design and calculation for pressure parts
BS EN 12953-4-2002 火管锅炉.锅炉的压力零件的工艺和制造 Shell
boilers - Workmanship and construction of pressure
parts of the boiler
BS EN 12953-5-2002 火管锅炉.锅炉的压力零件的制造、文献汇编和作标记过程的检查
Shell boilers - Inspection during construction,
documentation and marking of pressure parts
of the boiler
BS EN 12953-8-2002 火管锅炉.第8部分:防过量压力的安全保护装置的要求
Shell boilers - Requirements for safeguards
against excessive pressure
BS EN 13016-1-2007 液化石油产品.蒸气压力.气体饱和蒸气压(ASVP)的测定和干蒸气压当量值(DVPE)的计算
Liquid petroleum products - Vapour pressure
- Determination of air saturated vapour pressure
(ASVP) and calculated dry vapour pressure equivalent
(DVPE)
BS EN 13016-2-2007 液化石油产品.蒸气压力.40℃和100℃之间的绝对蒸气压(AVP)的测定
Liquid petroleum products - Vapour pressure
- Determination of absolute vapour pressure
(AVP) between 40 °C and 100 °C
BS EN 13042-5-2003 空心玻璃生产、处理和加工用机械和设备.安全要求.压力机
Machines and plants for the manufacture, treatment
and processing of hollow glass - Safety requirements
- Presses
BS EN 13094-2004 危险物品运输用槽罐.工作压力不超过0.5bar的金属槽罐.设计和建造
Tanks for the transport of dangerous goods -
Metallic tanks with a working pressure not exceeding
0,5 bar - Design and construction
BS EN 13160-2-2003 检漏系统.压力和真空系统 Leak detection
systems - Pressure and vacuum systems
BS EN 13244-1-2003 一般用途、排水和排污水的地下或地面压力系统用塑料管道系统.聚乙烯.总则
Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
General
BS EN 13244-2-2003 一般用途、排水和排污水的地下或地面压力系统用塑料管道系统.聚乙烯.管道
Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
Pipes
BS EN 13244-3-2003 一般用途、排水和排污水的地下或地面压力系统用塑料管道系统.聚乙烯.配件
Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
Fittings
BS EN 13244-4-2003 一般用途、排水和排污水的地下或地面压力系统用塑料管道系统.聚乙烯.阀门
Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
Valves
BS EN 13244-5-2003 一般用途、排水和排污水的地下或地面压力系统用塑料管道系统.聚乙烯.系统目的的适合性
Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
Fitness for purpose of the system
BS EN 13308-2002 危险物品运输用槽罐车.槽罐车用辅助设备.无压力平衡底阀
Tanks for transport of dangerous goods - Service
equipment for tanks - Non pressure balanced
footvalve
BS EN 13311-3-2001 生物技术.容器的性能标准.玻璃压力容器 Biotechnology
- Performance criteria for vessels - Glass pressure
vessels
BS EN 13316-2002 危险物品运输用槽罐车.槽罐车用辅助设备.压力平衡底阀
Tanks for transport of dangerous goods - Service
equipment for tanks - Pressure balanced footvalve
BS EN 13445-1-2002 非燃烧压力容器.总则 Unfired pressure
vessels - General
BS EN 13445-2-2002 非燃烧压力容器.材料 Unfired pressure
vessels - Materials
BS EN 13445-3-2002 无烧火的压力容器.设计 Unfired pressure
vessels - Design
BS EN 13445-4-2002 非燃烧压力容器.制造 Unfired pressure
vessels - Fabrication
BS EN 13445-5-2002 非燃烧压力容器.检测和试验 Unfired pressure
vessels - Inspection and testing
BS EN 13445-6-2002 非燃烧压力容器.球形石墨铸铁制压力容器和压力零部件的设计和生产要求
Unfired pressure vessels - Requirements for
the design and fabrication of pressure vessels
and pressure parts constructed from spheroidal
graphite cast iron
BS EN 13445-8-2006 非受火压力容器.铝和铝合金压力容器附加要求 Unfired
pressure vessels - Additional requirements for
pressure vessels of aluminium and aluminium
alloys
BS EN 13523-24-2004 卷材覆层金属.试验方法.耐粘结性和压力标记 Coil
coated metals - Test methods - Resistance to
blocking and pressure marking
BS EN 13562-2000 土工织物及其相关产品.抗水渗透性测定(液体静压力试验)
Geotextiles and geotextile-related products
- Determination of resistance to penetration
by water (hydrostatic pressure test)
BS EN 13566-2-2005 地下非压力排水和排污网修缮用塑料管道系统.第2部分:连续管加衬
Plastics piping systems for renovation of underground
non-pressure drainage and sewerage networks
— Part 2: Lining with continuous pipes
BS EN 13589-2004 石油及其制品的试验方法.沥青和沥青粘合剂.用压力延展法测定改性沥青的拉伸性能
Methods of test for petroleum and its products
- Bitumen and bituminous binders - Determination
of the tensile properties of modified bitumen
by the force ductility method
BS EN 13598-1-2003 无压力地下排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE).第1部分:包括浅层检
Plastics piping systems for non-pressure underground
drainage and sewerage - Unplasticized poly(vinyl
chloride) (PVC-U), polypropylene (PP) and polyethylene
(PE) - Specifications for ancillary fittings
including shallow inspection chambers
BS EN 13631-6-2003 民用爆炸物.烈性炸药.测定抗液体静压力 Explosives
for civil uses - High explosives - Determination
of resistance to hydrostatic pressure
BS EN 13673-1-2003 气体和蒸气的最大爆炸压力和最大压升的测定.最大爆炸压力的测定
Determination of the maximum explosion pressure
and the maximum rate of pressure rise of gases
and vapours - Determination of the maximum explosion
pressure
BS EN 13673-2-2005 气体和蒸气的最大爆炸压力和最大压升速率的测定.最大爆炸压升速率的测定
Determination of maximum explosion pressure
and the maximum rate of pressure rise of gases
and vapours - Determination of the maximum rate
of explosion pressure rise
BS EN 13736-2003 机床安全.气动压力机 Safety of machine
tools - Pneumatic presses
BS EN 13763-12-2003 民用爆炸物.雷管和传爆管.耐静水压力的测定 Explosives
for civil uses - Detonators and relays - Determination
of resistance to hydrostatic pressure
BS EN 13774-2003 最大工作压力小于或等于16巴的配气系统用阀门.性能要求
Valves for gas distribution systems with maximum
operating pressure less than or equal to 16
bar - Performance requirements
BS EN 13785-2005 丁烷、丙烷或其混合物用容量100 kg/h及以下和最大输出压力4巴及以下的调节器.不包括EN
12864中设备及其相关 Regulators with a capacity of up
to and including 100 kg/h, having a maximum
nominal outlet pressure of up to and including
4 bar, other than those covered by EN 12864
and their associated safety devices for butane,
propane or their mixtures
BS EN 13786-2004 丁烷、丙烷或它们的混合物用最大输出压力4巴及以下和100
kg/h及以下容积的自动转换阀及其相关安全设备 Automatic change-over
valves having a maximum outlet pressure of up
to and including 4 bar with a capacity of up
to and including 100 kg/h, and their associated
safety devices for butane, propane or their
mixtures
BS EN 13787-2001 入口压力达100巴的气体压力调节器及相关安全装置的弹性体.
Elastomers for gas pressure regulators and associated
safety devices for inlet pressures up to 100
bar
BS EN 13923-2005 丝绕制FRP压力容器.材料、设计、制造和测试 Filament-wound
FRP pressure vessels - Materials, design, manufacturing
and testing
BS EN 14025-2004 危险物品运输用容器.金属压力容器.设计和制造 Tanks
for the transport of dangerous goods - Metallic
pressure tanks - Design and construction
BS EN 14034-1-2005 尘云的爆炸特性测定.尘云最大爆炸压力pmax的测定
Determination of explosion characteristics of
dust clouds - Determination of the maximum explosion
pressure pmax of dust clouds
BS EN 14034-2-2006 尘云爆炸特性的测定.尘云爆炸压力上升的最大比率(dp/dt)的测定
Determination of explosion characteristics of
dust clouds - Determination of the maximum rate
of explosion pressure rise (dp/dt) max of dust
clouds
BS EN 14208-2004 可移动式储气瓶.气体运输用容量最高达1000升的焊接的压力桶规范.设计和建造
Transportable gas cylinders - Specification
for welded pressure drums up to 1000 litre capacity
for the transport of gases - Design and construction
BS EN 14276-1-2006 制冷系统和热泵用压力设备.压力容器.一般要求 Pressure
equipment for refrigerating systems and heat
pumps - Vessels - General requirements
BS EN 14276-2-2007 制冷系统和热泵用压力设备.管道.一般要求 Pressure
equipment for refrigerating systems and heat
pumps - Piping - General requirements
BS EN 14289-2004 皮革.物理和机械试验.水渗透压力的测定 Leather
- Physical and mechanical tests - Determination
of water penetration pressure
BS EN 14364-2006 地下压力排水和排污水塑料管道系统.未饱和聚酯树脂(UP)玻璃纤维增强的热固性塑料(GRP).管道、配件和连接件
Plastic piping systems for drainage and sewerage
with or without pressure - Glass reinforced
thermosetting plastics (GRP) based on unsaturated
polyester resin (UP) - Specifications for pipes,
fittings and joints
BS EN 14367-2005 不同压力区的非控制回流阻件.A型C族 Non controllable
backflow preventer with different pressure zones
- Family C, type A
BS EN 14382-2002 气压调节站和装置用安全设备.运行压力在100巴以下的气体安全关闭装置
Safety devices for gas pressure regulating stations
and installations - Gas safety shut-off devices
for operating pressure up to 100 bar
BS EN 14382-2005 气压调节站和装置用安全设备.进气口压力不超过100bar的气体安全截止装置
Safety devices for gas pressure regulating stations
and installations - Gas safety shut-off devices
for inlet pressures up to 100 bar
BS EN 14423-2004 额定压力到18bar的蒸汽软管用夹具型连接组件 Clamp
type coupling assemblies for use with steam
hoses rated for pressures up to 18 bar
BS EN 14452-2005 防饮用水回流污染的装置.带大气出口和活动部件公称压力DN10～DN20的管阻流器.B型D系列
Devices to prevent pollution by backflow of
potable water — Pipe interrupter with atmospheric
vent and moving element DN 10 to DN 20 — Family
D, type B
BS EN 14453-2005 防止饮用水回流污染的装置.带恒定大气压力孔DN 10～DN
20的管阻流器.C型D系列 Devices to prevent pollution by
backflow of potable water - Pipe interrupter
with permanent atmospheric vent DN 10 to DN
20 - Family D , type C
BS EN 14513-2005 可移动储气瓶.防爆板压力释放装置(不含乙炔储气瓶) Transportable
gas cylinders - Bursting disc pressure relief
devices (excluding acetylene gas cylinders)
BS EN 14584-2005 无损检验.声学辐射.验收试验过程中金属压力设备的检查.AE源的平面位置
Non-destructive testing - Acoustic emission
- Examination of metallic pressure equipment
during proof testing - Planar location of AE
sources
BS EN 14585-1-2006 压力设备用金属波纹软管组件.要求 Corrugated
metal hose assemblies for pressure applications
- Requirements
BS EN 14595-2005 危险物品运输罐.罐的辅助设备.压力和真空通气口 Tanks
for transport of dangerous goods - Service equipment
for tanks - Pressure and vacuum breather vent
BS EN 14627-2005 食品.痕量元素的测定.压力分解后用氢化法原子吸收光谱测定法测定硒和砷的总含量
Foodstuffs - Determination of trace elements
- Determination of total arsenic and selenium
by hydride generation atomic absorption spectrometry
(HGAAS) after pressure digestion
BS EN 14680-2006 非压力热塑管道系统用粘合剂.规范 Adhesives
for non-pressure thermoplastic piping systems
- Specifications
BS EN 14741-2006 热塑管和管道系统.非压力掩埋用接头.通过评估密封压力测定弹性密封件接合处的长期密封性能的试验方法
Thermoplastics piping and ducting systems -
Joints for buried non-pressure applications
- Test method for the long-term sealing performance
of joints with elastomeric seals by estimating
the sealing pressure
BS EN 14758-1-2005 无压力地下排水和污水用塑料管道系统.含矿物调节剂的聚丙烯(PP-MD).第1部分:管、配件和系统用规范.
Plastics piping systems for non-pressure underground
drainage and sewerage - Polypropylene with mineral
modifiers (PP-MD) - Part 1: Specifications for
pipes, fittings and the system
BS EN 14769-2006 石油及其产品的试验方法.沥青和沥青粘合剂.用压力老化容器(PAV)寻求加速长期老化的条件
Methods of test for petroleum and its products
- Bitumen and bituminousbi nders - Accelerated
long-term ageing conditioning by a pressure
ageingves sel (PAV)
BS EN 14801-2006 水和废水管道用产品的压力分类条件 Conditions
for Pressure Classification of Products for
Water andWastewater Pipelines
BS EN 14814-2007 压力下流体热塑性管道系统用胶粘剂.规范 Adhesives
for thermoplastic piping systems for fluids
under pressure - Specifications
BS EN 14876-2007 可运输储气瓶.定期检验和焊接钢压力桶试验 Transportable
gas cylinders - Periodic inspection and testing
of welded steel pressure drums
BS EN 14893-2006 液化石油气设备和附件.容量为150升～1000升可运输液化石油气(LPG)的焊接钢压力桶
LPG equipment and accessories - Transportable
liquefied petroleum gas (LPG) welded steel pressure
drums with a capacity between 150 litres and
1000 litres
BS EN 1490-2000 建筑物阀门.温度和压力结合型的释放阀门.试验和要求 Building
valves - Combined temperature and pressure relief
valves - Tests and requirements
BS EN 15266-2007 建筑物中工作压力等于0.5bar的气体用不锈钢柔性波管工具
Stainless steel pliable corrugated tubing kits
in buildings for gas with an operating pressure
up to 0,5 bar
BS EN 153000-1998 电子元器件质量评定协调体系.通用规范.分立压力接触电源半导体装置(合格鉴定批准)
Harmonized system of quality assessment for
electronic components - Generic specification:
discrete pressure contact power semiconductor
devices (qualification approval)
BS EN 15550-2007 动物饲料.压力消解后用石墨炉原子吸收光谱法(GF-AAS)测定镉和铅含量
Animal feeding stuffs - Determination of cadmium
and lead by graphite furnace atomic absorption
spectrometry (GF-AAS) after pressure digestion
BS EN 1594-2000 燃气供应系统.最大工作压力超过16巴的气体管道.功能要求
Gas supply systems - Pipelines for maximum operating
pressure over 16 bar - Functional requirements
BS EN 1595-1997 硼硅酸盐玻璃3.3制压力设备.设计、制造和试验一般规则
Pressure equipment made from borosilicate glass
3.3. General rules for design, manufacture and
testing
BS EN 1605-1997 建筑物用的隔热产品.在特定压力负载和温度条件下变形的测定.
Thermal insulating products for building applications
- Determination of deformation under specified
compressive load and temperature conditions
BS EN 1653-1998 铜和铜合金.锅炉、压力容器和热水保温装置用的板、薄板材和圆形材
Copper and copper alloys - Plate, sheet and
circles for boilers, pressure vessels and hot
water storage units
BS EN 1671-1997 建筑物外压力污水系统 Pressure sewerage
systems outside buildings
BS EN 1760-1-1998 机械安全.压力敏感防护装置.压力敏感垫和压力敏感地板的设计和试验通用规则
Safety of machinery - Pressure sensitive protective
devices - General principles for the design
and testing of pressure sensitive mats and pressure
sensitive floors
BS EN 1775-2007 燃气供应.建筑物用燃气管道.最大工作压力不超过或等于5巴.功能推荐标准
Gas supply - Gas pipework for buildings - Maximum
operating pressure less than or equal to 5 bar
- Functional recommendations
BS EN 1796-2006 有或无压力供水塑料管道系统.基于不饱和聚酯(UP)的玻璃增强热固塑料(GRP)
Plastics piping systems for water supply with
or without pressure - Glass-reinforced thermosetting
plastics (GRP) based on unsaturated polyester
resin (UP)
BS EN 1854-2006 气体燃烧器和燃气器具的压力敏感装置 Pressure sensing
devices for gas burners and gas burning appliances
BS EN 1893-2005 高级工业陶瓷.大气压力下空气中高温情况下陶瓷成分的机械特性.拉伸特性的测定
Advanced technical ceramics - Mechanical properties
of ceramic composites at high temperature in
air at atmospheric pressure - Determination
of tensile properties
BS EN 1894-2005 高级工业陶瓷.惰性气体环境中高温情况下陶瓷成分的机械特性.通过有凹槽试样的压力荷载测定剪切强度
Advanced technical ceramics - Mechanical properties
of ceramic composites at high temperature under
inert atmosphere - Determination of shear strength
by compression loading of notched specimens
BS EN 1989-2000 热塑管道系统.地下埋装的非承压污水设施用连接件.通过对密封压力的估计对带热塑弹力密封件的连接件的长期密
Thermoplastics piping systems - Joints for buried
non-pressure sewerage applications - Test method
for long-term sealing performance of joints
with thermoplastic elastomer (TPE) seals by
estimating the sealing pressure
BS EN 200-1992 卫生用水龙头.单一和混合水龙头(标称尺寸1/2)PN10通用技术规范.最小流动压力0.05MPa(0.5bar)
Sanitary tapware - General technical specifications
for single taps and mixer taps (nominal size
1/2) PN 10 - Minimum flow pressure of 0.05 MPa
(0.5 bar)
BS EN 20811-1982 纺织品.耐水渗透性的测定.静水压力试验 Textiles
- Determination of resistance to water penetration
- Hydrostatic pressure test
BS EN 22858-1993 端吸式离心泵(额定压力16巴).命名、标称效率点和尺寸
End-suction centrifugal pumps (rating 16 bar)
- Designation, nominal duty point and dimensions
BS EN 23035-1994 单面和单壁瓦楞纤维纸板耐压力的测定定 Single-faced
and single-wall corrugated fibreboard - Determination
of flat crush resistance
BS EN 2624-2007 航空航天系列.水压系统元件的压力脉冲测试 Aerospace
series - Pressure impulse testing of hydraulic
system components
BS EN 278-1991 采用压力达200毫巴可燃气体的家用器具膜片用橡胶材料规范
Specification for rubber materials for diaphragms
in domestic appliances using combustible gases
up to 200 mbar
BS EN 279-1991 使用压力达200毫巴可燃气体的家用器具的动态密封件用均质橡胶材料规范
Specification for homogenous rubber materials
for dynamic seals in domestic appliances using
combustible gases up to 200 mbar
BS EN 286-1 1998 + A2-1998 罐装空气或氮气用非受火简易压力容器.通用压力容器
Simple unfired pressure vessels designed to
contain air or nitrogen - Pressure vessels for
general purposes
BS EN 286-1-1998 专用于空气或氮气的简单非受火压力容器.一般用途压力容器
Simple unfired pressure vessels designed to
contain air or nitrogen - Pressure vessels for
general purposes
BS EN 286-2-1992 装空气或氮气用简单不用火加热的压力容器.汽车和拖车气动刹车和辅助系统用压力容器规范
Simple unfired pressure vessels designed to
contain air or nitrogen - Specification for
pressure vessels for air braking and auxiliary
systems for motor vehicles and their trailers
BS EN 286-3-1995 装空气或氮气用的不用火加热的一般压力容器.第3部分:用于铁路运输车辆空气制动和辅助气动设备的钢制压力容
Simple unfired pressure vessels designed to
contain air or nitrogen - Steel pressure vessels
designed for air braking equipment and auxiliary
pneumatic equipment for railway rolling stock
BS EN 286-4-1995 装空气或氮气用的不点火加热的一般压力容器.第4部分:用于铁路运输车辆空气制动和辅助气动设备的铝合金压力
Simple unfired pressure vessels designed to
contain air or nitrogen - Aluminium alloy pressure
vessels designed for air braking equipment and
auxiliary pneumatic equipment for railway rolling
stock
BS EN 289-2004 塑料和橡胶机械.压力机.安全要求 Plastics and
rubber machines - Presses - Safety requirements
BS EN 291-1992 压力为200毫巴及其以下的家用可燃气体静态密封用橡胶密封件的材料规范
Rubber seals - Static seals in domestic appliances
for combustible gas up to 200 mbar - Specification
for material
BS EN 293-1992 油压力雾化喷嘴.最低要求.试验 Specification
for oil pressure atomizing nozzles - Minimum
requirements - Testing
BS EN 3-8-2006 便携式灭火器.第8部分:对EN 3-7的最大允许压力≤30bar灭火器的结构、耐压和机械试验的附加要求
Portable fire extinguishers - Part 8: Additional
requirements to EN 3-7 for the construction,
resistance to pressure and mechanical tests
for extinguishers with a maximum allowable pressure
equal to or lower than 30 bar
BS EN 303-4-1999 供暖锅炉.带强制通风燃烧器的供暖锅炉.最大操作压力3巴、最高输出达70kW的带强制通风燃油器的锅炉的特殊要
Heating boilers - Heating boilers with forced
draught burners - Heating boilers with forced
draught burners - Special requirements for boilers
with forced draught oil burners with outputs
up to 70 kW and a maximum operating pressure
of 3 bar - Terminology, special requirements,
testing and marking
BS EN 3079-2006 8°30'压力＜28000kPa的导管接头.适配器.米制系列.技术规范
Pipe coupling 8 °30' up to 28000 kPa - Adaptors
- Metric series - Technical specification
BS EN 3268-2001 航空航天系列.钛合金8°30'管连接件.压力管塞 Aerospace
series - Pipe coupling 8 °30' in titanium alloy
- Pressure plug
BS EN 334-1999 入口压力不大于100bar的气体压力调节器 Gas pressure
regulators for inlet pressures up to 100 bar
BS EN 334-2005 进气口压力不大于100bar的气压调节器 Gas pressure
regulators for inlet pressures up to 100 bar
BS EN 3688-2001 航空航天系列.焊接管用钛合金制T环形填充物.14000kPa公称压力
Aerospace series - T-ring fillers in titanium
alloy for welded pipes - 14000 kPa nominal pressure
BS EN 3689-2001 航空航天系列.焊接管用钛合金制T环形填充物.28000kPa公称压力
Aerospace series - T-ring fillers in titanium
alloy for welding pipes - 28000 kPa nominal
pressure
BS EN 437-2003 试验气体.试验压力.器具分类 Test gases - Test
pressures - Appliance categories
BS EN 464-1994 防护服.对包括气溶液体和固体粒子的液体和气体化学物质的防护.试验方法.气体密封服的密封性测定(内压力试验
Protective clothing - Protection against liquid
and gaseous chemicals, including liquid aerosols
and solid particles - Test method - Determination
of leak-tightness of gas-tight suits (Internal
Pressure Test)
BS EN 472-1995 压力计.词汇 Pressure gauges - Vocabulary
BS EN 50216-5-2002 电力变压器和反应堆配件.液位、压力装置和流量指示计
Power transformer and reactor fittings - Liquid
level, pressure and flow indicators, pressure
relief devices and dehydrating breathers
BS EN 50289-3-15-2003 通信电缆.试验方法规范.机械试验方法.海底电缆耐静水压力
Communication cables - Specifications for test
methods - Mechanical test methods - Underwater
cable resistance to hydrostatic pressure
BS EN 50464-1-2007 最高压力不超过36kV的设备用50Hz、50kVA至2500kVA的三相油浸式配电变压器.一般要求
Three-phase oil-immersed distribution transformers
50 Hz, from 50 kVA to 2500 kVA with highest
voltage for equipment not exceeding 36 kV -
General requirements
BS EN 50464-2-1-2007 最高压力不超过36kV的设备用50Hz、50kVA至2500kVA的三相油浸式配电变压器.高压侧和/或低压侧上带电缆接线盒
Three-phase oil-immersed distribution transformers
50 Hz, from 50 kVA to 2500 kVA with highest
voltage for equipment not exceeding 36 kV -
Distribution transformers with cable boxes on
the high-voltage and/or low-voltage side - General
requirements
BS EN 50464-2-2-2007 最高压力不超过36kV的设备用50Hz、50kVA至2500kVA的三相油浸式配电变压器.高压侧和/或低压侧上带电缆接线盒
Three-phase oil-immersed distribution transformers
50 Hz, from 50 kVA to 2 500 kVA with highest
voltage for equipment not exceeding 36 kV -
Distribution transformers with cable boxes on
the high-voltage and/or low-voltage side - Cable
boxes type 1 for use on distribution transformers
meeting the requirements of EN 50464-2-1
BS EN 50464-2-3-2007 最高压力不超过36kV的设备用50Hz、50kVA至2500kVA的三相油浸式配电变压器.高压侧和/或低压侧上带电缆接线盒
Three-phase oil-immersed distribution transformers
50 Hz, from 50 kVA to 2500 kVA with highest
voltage for equipment not exceeding 36 kV -
Distribution transformers with cable boxes on
the high-voltage and/or low-voltage side - Cable
boxes type 2 for use on distribution transformers
meeting the requirements of EN 50464-2-1
BS EN 50464-3-2007 最高压力不超过36kV的设备用50Hz、50kVA至2500kVA的三相油浸式配电变压器.载有非正弦电流的变压器额定功率
Three-phase oil-immersed distribution transformers
50 Hz, from 50 kVA to 2500 kVA with highest
voltage for equipment not exceeding 36 kV -
Determination of the power rating of a transformer
loaded with non-sinusoidal currents
BS EN 50464-4-2007 最高压力不超过36kV的设备用50Hz、50kVA至2500kVA的三相油浸式配电变压器.关于增压式波形槽的要求和试验
Three-phase oil-immersed distribution transformers
50 Hz, from 50 kVA to 2500 kVA with highest
voltage for equipment not exceeding 36 kV -
Requirements and tests concerning pressurised
corrugated tanks
BS EN 512-1995 纤维水泥制品.压力管道和接头 Fibre-cement products
- Pressure pipes and joints
BS EN 562-2003 气焊设备.焊接、切割和相关工艺用压力计 Gas welding
equipment - Pressure gauges used in welding,
cutting and allied processes
BS EN 60079-2-2004 爆炸性气体环境用电气设备.压力封装型"p"
Electrical apparatus for explosive gas atmospheres
- Pressurized enclosures "p"
BS EN 60811-3-1-1995 电缆的绝缘和护套材料.通用试验方法.聚氯乙烯专用方法.高温下压力试验.耐裂性试验
Insulating and sheathing materials of electric
cables - Common test methods - Methods specific
to PVC compounds - Pressure test at high temperature
- Tests for resistance to cracking
BS EN 61094-2-1994 测量传声器的规范.用互逆性技术对实验室标准传声器进行压力校准的基本方法
Specification for measurement microphones -
Primary method for pressure calibration of laboratory
standard microphones by the reciprocity technique
BS EN 61094-5-2002 测量传声器.用比较片做用工作标准传声器的压力校准方法
Measurement microphones - Methods for pressure
calibration of working standard microphones
by comparison
BS EN 61846-1999 超声波.压力脉冲碎石器.电磁场特性 Ultrasonics
- Pressure pulse lithotripters - Characteristics
of fields
BS EN 639-1995 包括接头和配件的混凝土压力管的共同要求 Common requirements
for concrete pressure pipes including joints
and fittings
BS EN 640-1995 钢筋混凝土压力管和分布钢筋混凝土压力管（非圆柱型），包括接头和配件
Reinforced concrete pressure pipes and distributed
reinforcement concrete pressure pipes (non-cylinder
type), including joints and fittings
BS EN 641-1995 包括接头和配件的圆柱型加筋混凝土压力管 Reinforced
concrete pressure pipes, cylinder type, including
joints and fittings
BS EN 642-1995 包括接头、配件和管道预应力钢特殊要求的圆柱型和非圆柱型预应力混凝土压力管
Prestressed concrete pressure pipes, cylinder
and non-cylinder, including joints, fittings
and specific requirement for prestressing steel
for pipes
BS EN 692-2005 机床.机械压力.安全 Machine tools - Mechanical
presses - Safety
BS EN 712-1995 热塑管道系统.压力管和配件之间端部承载的机械接合.在恒定径向力下抗拔出性能的试验方法
Thermoplastics piping systems - End-load bearing
mechanical joints between pressure pipes and
fittings - Test method for resistance to pull-out
under constant longitudinal force
BS EN 713-1995 塑料管道系统.管件和聚烯烃压力管的机械连接.组件承受弯曲作用时内部压力密封性的试验方法
Plastics piping systems - Mechanical joints
between fittings and polyolefin pressure pipes
- Test method for leaktightness under internal
pressure of assemblies subjected to bending
BS EN 714-1995 热塑管道系统.压力管和模塑管件的无端负荷弹性密封环型连接件.在无轴向推力时内部流体静压力下密封性的试验
Thermoplastics piping systems - Non-end-load-bearing
elastomeric sealing ring type joints between
pressure pipes and moulded fittings - Test method
for leaktightness under internal hydrostatic
pressure without end thrust
BS EN 715-1995 热塑管道系统.小直径压力管和配件间端部负荷轴承接头.在包含端推力的内部水压下密封性的试验方法
Thermoplastics piping systems - End-load-bearing
joints between small diameter pressure pipes
and fittings - Test method for leaktightness
under internal water pressure, including end
thrust
BS EN 738-3-1999 医疗用气体的压力调节器.与气瓶阀组合的压力调节器 Pressure
regulators for use with medical gases - Pressure
regulators integrated with cylinder valves
BS EN 738-4-1999 医疗用气体的压力调节器.医疗设备用低压力调节器 Pressure
regulators for use with medical gases - Low-pressure
regulators intended for incorporation into medical
equipment
BS EN 764-1-2004 压力设备.术语.压力、温度、体积和标称尺寸 Pressure
equipment - Terminology - Pressure, temperature,
volume, nominal size
BS EN 764-2-2002 压力设备.量值、符号和单位 Pressure equipment
- Quantities, symbols and units
BS EN 764-3-2002 压力设备.有关方的定义 Pressure equipment
- Definition of parties involved
BS EN 764-4-2002 压力设备.金属材料的交货技术条件的编制 Pressure
equipment - Establishment of technical delivery
conditions for metallic materials
BS EN 764-5-2002 压力设备.材料的合格性和检验文献 Pressure equipment
- Compliance and inspection documentation of
materials
BS EN 764-7-2002 压力设备.不用火加热的压力容器的安全性系统 Pressure
equipment - Safety systems for unfired pressure
vessels
BS EN 773-1999 液压压力排气管、排水管和污水管道中使用部件的一般要求 General
requirements for components used in hydraulically
pressurized discharge pipes, drains and sewers
BS EN 802-1995 塑料管和管道系统.压力管道系统的注射铸造热塑性部件.最大挤压变形试验方法
Plastics piping and ducting systems - Injection-moulded
thermoplastics fittings for pressure piping
systems - Test method for maximum deformation
by crushing
BS EN 803-1995 塑料管道系统.压力管道的弹性密封圈式连接件用注模制热塑塑料性配件.耐无部端推力的快速内压的试验方法
Plastics piping systems - Injection-moulded
thermoplastics fittings for elastic sealing
ring type joints for pressure piping - Test
method for resistance to a short-term internal
pressure without end thrust
BS EN 804-1995 塑料管道系统.压力管道溶剂胶粘接头的注射模塑承口连接管件.短期内部液压压力的试验方法
Plastics piping systems - Injection-moulded
socket fittings for solvent-cemented joints
for pressure piping - Test method for resistance
to a short-term internal hydrostatic pressure
BS EN 837-1-1998 压力计.波登压力计.规格,计量,要求和试验 Pressure
gauges - Bourdon tube pressure gauges - Dimensions,
metrology, requirements and testing
BS EN 837-2-1998 压力计.压力计的选择和安装推荐规范 Pressure
gauges - Selection and installation recommendations
for pressure gauges
BS EN 837-3-1998 压力计.膜式压力计和膜合式压力计.尺寸、计量、要求和试验
Pressure gauges - Diaphragm and capsule pressure
gauges - Dimensions, metrology, requirements
and testing
BS EN 88-1991 入口压力达200毫巴的燃气器具的压力调节器 Pressure
governors for gas appliances for inlet pressures
up to 200 mbar
BS EN 911-1996 塑料管道系统.热塑塑料压力管道用的弹性密封环型接头和机械接头.外部流体静压条件下防漏密封试验方法
Plastics piping systems - Elastomeric sealing
ring type joints and mechanical joints for thermoplastics
pressure piping - Test method for leaktightness
under external hydrostatic pressure
BS EN 976-1-1997 玻璃增强塑料地下油罐.非压力存储液体石油基燃料的卧式园柱油罐.单壁油罐试验方法和要求
Underground tanks of glass-reinforced plastics
(GRP) - Horizontal cylindrical tanks for the
non-pressure storage of liquid petroleum based
fuels - Requirements and test methods for single
wall tanks
BS EN 976-2-1997 玻璃增强塑料地下油罐.非压力存储液体石油基燃料的卧式园柱油罐.单壁油罐的运输,储存,搬运和安装
Underground tanks of glass-reinforced plastics
(GRP) - Horizontal cylindrical tanks for the
non-pressure storage of liquid petroleum based
fuels - Transport, handling, storage and installation
of single wall tanks
BS EN ISO 10079-3-2000 医疗吸引设备.真空或压力吸引设备 Medical
suction equipment - Suction equipment powered
from a vacuum or pressure source
BS EN ISO 10426-4-2005 石油和天然气工业.油井固井用水泥和材料.在大气压力下泡沫水泥浆的制备和试验
Petroleum and natural gas industries - Cements
and materials for well cementing - Preparation
and testing of foamed cement slurries at atmospheric
pressure
BS EN ISO 10426-5-2006 石油和天然气工业.油井固井用水泥和材料.在大压力下固井水泥加工制剂的收缩和膨胀的测定
Petroleum and natural gas industries - Cements
and materials for well cementing - Determination
of shrinkage and expansion of well cement formulations
at atmospheric pressure
BS EN ISO 10524-1-2006 医用气体设备用的压力调节器和带流量计的压力调节器
Pressure regulators for use with medical gases
- Pressure regulators and pressure regulators
with flow-metering devices
BS EN ISO 10524-2-2007 医用气体的压力调节器.歧管和线管压力调节器
Pressure regulators for use with medical gases
- Manifold and line pressure regulators
BS EN ISO 1167-1-2006 流体传输用热塑管、配件和组件.抗内压力的测定.通用方法
Thermoplastics pipes, fittings and assemblies
for the conveyance of fluids - Determination
of the resistance to internal pressure - General
method
BS EN ISO 1167-2-2006 流体传输用热塑管、配件和组件.抗内压力的测定.管道试件制备
Thermoplastics pipes, fittings and assemblies
for the conveyance of fluids - Determination
of the resistance to internal pressure - Preparation
of pipe test pieces
BS EN ISO 12048-2001 包装.满装运输包装.用压力试验机的压力试验和堆积试验
Packaging - Complete, filled transport packages
- Compression and stacking tests using a compression
tester
BS EN ISO 12162-1996 压力用热塑性塑料管道和管件.分类和设计.总体使用（设计）系数
Thermoplastics materials for pipes and fittings
for pressure applications - Classification and
design - Overall service (design) coefficient
BS EN ISO 13760-2000 流体输送用压力塑料管.Miner规则.累积损坏的计算方法
Plastics pipes for the conveyance of fluids
under pressure - Miner's rule - Calculation
method for cumulative damage
BS EN ISO 13846-2001 塑料管道系统.热塑性压力管用端负载和无端负载支承组件和接头.内部水压下长期密封性的试验方法
Plastics piping systems - End-load-bearing and
non-end-load bearing assemblies and joints for
thermoplastics pressure piping - Test method
for long-term leaktightness under internal water
pressure
BS EN ISO 15265-2004 热环境的人类工效学.热工作条件下防止压力和不适的风险评估政策
Ergonomics of the thermal environment - Risk
assessment strategy for the prevention of stress
or discomfort in thermal working conditions
BS EN ISO 15364-2000 船舶与海上技术.散货船真空/压力阀 Ships
and marine technology - Pressure/vacuum valves
for cargo tanks
BS EN ISO 15616-3-2003 高质量焊接和切割用CO2激光束机的验收试验.气体流量和压力测量仪的校正
Acceptance tests for CO2- laser beam machines
for high quality welding and cutting - Calibration
of instruments for measurement of gas flow and
pressure
BS EN ISO 15996-2005 储气瓶.剩余压力阀.一般要求和型式试验 Gas
cylinders - Residual pressure valves - General
requirements and type testing
BS EN ISO 17654-2003 金属材料焊缝的有损试验.电阻焊接.电阻缝焊的压力试验
Destructive tests on welds in metallic materials
- Resistance welding - Pressure test on resistance
seam welds
BS EN ISO 20623-2004 石油及其产品的试验方法.BS 2000-239:流体的极限压力和耐磨特性测定.四球法(欧洲条件)
Petroleum and related products - Determination
of the extreme-pressure and anti-wear properties
of fluids - Four ball method (European conditions)
BS EN ISO 23251-2006 石油、石化和天然气工业.压力释放和降压系统 Petroleum,
petrochemical and natural gas industries - Pressure-relieving
and depressuring systems
BS EN ISO 2556-2001 塑料.在大气压力下薄膜和薄板的气体透过率的测定.测压法
Plastics - Determination of the gas transmission
rate of films and thin sheets under atmospheric
pressure - Manometric method
BS EN ISO 2811-4-2001 涂料和清漆.密度的测定.压力杯法 Paints
and varnishes - Determination of density - Pressure
cup method
BS EN ISO 3405-2000 石油及其制品的试验方法.石油产品.大气压力下蒸馏特性的测定
Methods of test for petroleum and its products
- Petroleum products - Determination of distillation
characteristics at atmospheric pressure
BS EN ISO 3744-1994 声学.用声压力测定噪声源的声功率级.在声音反射平面上基本自由场中的测量方法
Acoustics - Determination of sound power levels
of noise sources using sound pressure - Engineering
method in an essentially free field over a reflecting
plane
BS EN ISO 3746-1996 声学.用噪声压力测定噪声功率级.在反射平面上利用包封测量表面的测量法
Acoustics - Determination of sound power levels
of noise sources using sound pressure - Survey
method using an enveloping measurement surface
over a reflecting plane
BS EN ISO 3993-1996 液化石油气和轻质烃类.密度或相对密度的测定.压力石油密度计法
Liquefied petroleum gas and light hydrocarbons
- Determination of density or relative density
- Pressure hydrometer method
BS EN ISO 4256-1998 液体石油产品.标准蒸气压力的测定.LPG法 Liquid
petroleum products - Determination of gauge
vapour pressure - LPG method
BS EN ISO 4622-1993 色漆和清漆.堆积压力试验 Paints and
varnishes - Pressure test for stackability
BS EN ISO 6520-2-2002 焊接及相关工艺.金属材料中几何缺陷的分类.压力焊
Welding and allied processes - Classification
of geometric imperfections in metallic materials
- Welding with pressure
BS EN ISO 7291-2001 气焊设备.300bar以下的焊接、切削及相关工艺用汇流系统用压力调节器
Gas welding equipment - Pressure regulators
for manifold systems used in welding, cutting
and allied processes up to 300 bar
BS EN ISO 7458-2004 玻璃容器.耐内压力.试验方法 Glass containers
- Internal pressure resistance - Test methods
BS EN ISO 7751-1997 橡胶和塑料软管和软管组件.试验压力和爆破压力与设计工作压力之比
Rubber and plastics hoses and hose assemblies
- Ratios of proof and burst pressure to design
working pressure
BS EN ISO 8536-10-2004 医用输液设备.与压力输液仪器一起使用的输液管附件
Infusion equipment for medical use - Accessories
for fluid lines for use with pressure infusion
equipment
BS EN ISO 8536-11-2004 医用输液设备.与压力输液仪器一起使用的输液过滤器
Infusion equipment for medical use - Infusion
filters for use with pressure infusion equipment
BS EN ISO 8536-8-2004 医用输液器具.与压力输液仪器一起使用的输液器具
Infusion equipment for medical use - Infusion
equipment for use with pressure infusion apparatus
BS EN ISO 8536-9-2004 医用输液设备.与压力输液仪器一起使用的输液管
Infusion equipment for medical use - Fluid lines
for use with pressure infusion equipment
BS EN ISO 8973-1999 液化石油气.密度和蒸气压力的计算方法 Liquefied
petroleum gases - Calculation method for density
and vapour pressure
BS EN ISO 9311-3-2005 热塑性管道系统用胶粘剂.测定耐内压力性的试验方法
Adhesives for thermoplastic piping systems -
Test method for the determination of resistance
to internal pressure
BS EN ISO 9863-1-2005 土工合成织物.特定压力下厚度的测定.单层 Geosynthetics
- Determination of thickness at specified pressures
- Single layers
BS EN ISO 9863-2-1996 土工织物和相关产品.特定压力下厚度的测定.多层制品的单层厚度测定程序
Geotextiles and geotextile-related products
- Determination of thickness at specified pressures
- Procedure for determination of thickness of
single layers of multilayer products
BS G 226-1979 压力高度计系统伺服型计数器和指示器规范 Specification
for counter and pointer, servo type, pressure
altimeter systems
BS G 240-1988 航空用压力传感器规范 Specification for pressure
transducers for use on aircraft
BS G 259-1996 航空用设备.机载设备环境和操作条件.湿度、温度和压力试验 Aircraft
equipment - Environmental and operating conditions
for airborne equipment - Humidity, temperature
and pressure tests
BS IEC 60747-14-3-2001 分立半导体器件和集成电路.半导体器件.半导体传感器.压力传感器
Discrete semiconductor devices and integrated
circuits - Semiconductor devices - Semiconductor
sensors - Pressure sensors
BS IEC 62117-2000 核反应堆仪表.压力轻水反应堆(PWR).冷停过程中堆芯充分冷却的监测
Nuclear reactor instrumentation - Pressurized
light water reactors (PWR) - Monitoring adequate
cooling within the core during cold shutdown
BS ISO 10767-1-1996 液压流体动力.对系统和部件产生压力波动级的测定.第1部分:泵精度法
Hydraulic fluid power - Determination of pressure
ripple levels generated in systems and components
- Precision method for pumps
BS ISO 10767-2-1999 液压传动.系统和元件中产生压力波动值的测定.泵的简化方法
Hydraulic fluid power - Determination of pressure
ripple levels generated in systems and components
- Simplified method for pumps
BS ISO 10767-3-2000 液压传动.系统和元件产生压力波动值的测定.马达用方法
Hydraulic fluid power - Determination of pressure
ripple levels generated in systems and components
- Method for motors
BS ISO 10771-1-2002 液压流体动力.金属压力容器外壳的疲劳压力试验.试验方法
Hydraulic fluid power - Fatigue pressure testing
of metal pressure-containing envelopes - Test
method
BS ISO 12334-2000 航空航天.液压的压力补偿的变量输送泵.35000KPa系统的一般要求
Aerospace - Hydraulic, pressure-compensated,
variable delivery pumps - General requirements
for 35000 kPa systems
BS ISO 13994-1998 防液体化学制品的防护服装.防护服装材料在压力下防液体渗透的阻力测定
Clothing for protection against liquid chemicals
- Determination of the resistance of protective
clothing materials to penetration by liquids
under pressure
BS ISO 14623-2004 航天系统.压力容器和压力构件.设计和操作 Space
systems - Pressure vessels and pressurized structures
- Design and operation
BS ISO 15081-2005 农业灌溉设备.压力灌溉系统用图形符号 Agricultural
irrigation equipment - Graphical symbols for
pressurized irrigation systems
BS ISO 15171-1-1999 液压和一般用途的连接.诊断用的液压联结器.不用于压力条件下连接的联结器
Connections for fluid power and general use
- Hydraulic couplings for diagnostic purposes
- Coupling not for connection under pressure
BS ISO 15364-2000 船舶技术.货槽用压力/真空阀 Ships and marine
technology. Pressure/vacuum valves for cargo
tanks
BS ISO 15379-1-2004 铝生产用含碳材料.阴极块材料.压力作用下由于钠渗透引起的膨胀的测定
Carbonaceous materials for the production of
aluminium - Cathode block materials - Determination
of the expansion due to sodium penetration with
application of pressure
BS ISO 15379-2-2004 铝生产用碳质材料.阴极块材料.无压力作用下由于钠渗透引起的膨胀的测定
Carbonaceous materials for the production of
aluminium - Cathode block materials - Determination
of the expansion due to sodium penetration without
application of pressure
BS ISO 15734-2003 船舶和海上技术.静水压力释放装置 Ships and
marine technology - Hydrostatic release units
BS ISO 16028-2000 液压流体动力.在20MPa(200巴)到31.5MPa(315巴)的压力下使用平面型速动联轴器.规范
Hydraulic fluid power - Flush-face type, quick-action
couplings for use at pressures of 20 MPa (200
bar) to 31,5 MPa (315 bar) - Specifications
BS ISO 16232-3-2007 道路车辆.液压管路部件清洁度.压力漂洗萃取污染物的方法
Road vehicles - Cleanliness of components of
fluid circuits - Method of extraction of contaminants
by pressure rinsing
BS ISO 16422-2006 压力送水用定向未增塑聚(氯)乙烯(PVC-O)制作的管道和接头.规范
Pipes and joints made of oriented unplasticized
poly(vinyl chloride) (PVC-O) for the conveyance
of water under pressure - Specifications
BS ISO 16873-2002 液压流体动力.压力开关.安装表面 Hydraulic
fluid power - Pressure switches - Mounting surfaces
BS ISO 17484-1-2006 塑料管道系统.最大工作压力达到5bar(500kPa)及以下的室内燃气装置用多层管道系统.系统规范
Plastics piping systems - Multi-layer pipe systems
for indoor gas installations with a maximum
operating pressure up to and including 5 bar
(500 kPa) - Specifications for systems
BS ISO 17744-2004 塑料.作为温度和压力函数的比容的测定(pvT图).活塞装置法
Plastics - Determination of specific volume
as a function of temperature and pressure (pVT
diagram) - Piston apparatus method
BS ISO 18172-1-2007 储气瓶.可再充装的焊接不锈钢气瓶.试验压力≤6MPa
Gas cylinders - Refillable welded stainless
steel cylinders - Test pressure 6 MPa and below
BS ISO 18172-2-2007 储气瓶.可再充装的焊接不锈钢气瓶.试验压力≥6MPa
Gas cylinders - Refillable welded stainless
steel cylinders - Test pressure greater than
6 MPa
BS ISO 18752-2006 橡胶软管和软管组件.金属丝或纺织物.液压设备用的单胎压力加强型.规范
Rubber hoses and hose assemblies - Wire- or
textile-reinforced single pressure types for
hydraulic applications - Specification
BS ISO 19973-4-2007 气压传动.通过测试评定元件的可靠度.压力调节器
Pneumatic fluid power - Assessment of component
reliability by testing - Pressure regulators
BS ISO 21750-2006 道路车辆.有关增进轮胎充气压力监控的安全 Road
vehicles - Safety enhancement in conjunction
with tyre inflation pressure monitoring
BS ISO 2186-2007 封闭管道中的流体流量.一次和二次元件间压力信号传送的连接件
Fluid flow in closed conduits - Connections
for pressure signal transmissions between primary
and secondary elements
BS ISO 23251-2006 石油、石化和天然气工业.释放压力和解压系统 Petroleum,
petrochemical and natural gas industries - Pressure-relieving
and depressuring systems
BS ISO 2944-2000 液压动力系统和元件.标称压力 Fluid power
systems and components - Nominal pressures
BS ISO 3007-2002 石油及其产品试验方法.BS 2000-69: 石油产品.蒸汽压力的测定.瑞利法
Methods of test for petroleum and its products
- BS 2000-69: Petroleum products - Determination
of vapour pressure - Reid method
BS ISO 3322-1996 流体动力系统和部件.液压缸.标称压力 Fluid power
systems and components - Cylinders - Nominal
pressures
BS ISO 4179-2005 压力和非压力管道用球墨铸铁管和配件.水泥灰浆内衬 Ductile
iron pipes and fittings for pressure and non-pressure
pipelines - Cement mortar lining
BS ISO 4250-2-2006 土方机械轮胎和轮辋.载重和充气压力 Earth-mover
tyres and rims - Loads and inflation pressures
BS ISO 5596-2000 液压传动.隔离式充气蓄能器.压力、容积范围和特性量 Hydraulic
fluid power - Gas-loaded accumulators with separator
- Ranges of pressures and volumes and characteristic
quantities
BS ISO 6162-1-2002 液压传动.带对开夹或整体式法兰夹的法兰接头以及公制或英制螺钉.在压力为3,5MPa(35bar)至35MPa(350bar),DN1
Hydraulic fluid power - Flange connectors with
split or one-piece flange clamps and metric
or inch screws - Flange connectors for use at
pressures of 3,5 MPa (35 bar) to 35 MPa (350
bar), DN 13 to DN 127
BS ISO 6162-2-2002 液压传动.带对开夹或整体式法兰夹的法兰接头以及公制或英制螺钉.在压力为35MPa(350bar)至40MPa(400bar),DN1
Hydraulic fluid power - Flange connectors with
split or one-piece flange clamps and metric
or inch screws - Flange connectors for use at
pressures of 35 MPa (350 bar) to 40 MPa (400
bar), DN 13 to DN 51
BS ISO 6771-2007 航空航天.流体系统和部件.压力和温度分类 Aerospace
- Fluid systems and components - Pressure and
temperature classifications
BS ISO 7169-2007 航空航天.液压系统用24°锥形的、压力范围截至3000psi或21000kPa的可拆卸管接头.采购规范(英制/米制)
Aerospace - Separable tube fittings for fluid
systems, for 24 ° cones, for pressures up to
3000 psi or 21000 kPa - Procurement specification,
inch/metric
BS ISO 727-2-2005 压力管件用由未增塑聚氯乙烯(PVC-U)、氯化聚氯乙烯(PVC-C)或丙烯腈/丁二烯/苯乙烯(ABS)制的带普通管套的管
Fittings made from unplasticized poly(vinyl
chloride) (PVC-U), chlorinated poly(vinyl chloride)
(PVC-C) or acrylonitrile/butadiene/styrene (ABS)
with plain sockets for pipes under pressure
- Inch-based series
BS ISO 9022-18-1995 光学和光学仪器.环境试验方法.混合式湿热压力和低内压力
Optics and optical instruments - Environmental
test methods - Combined damp heat and low internal
pressure
BS ISO 9393-1-2004 工业用热塑性阀门.压力试验方法和要求.总则 Thermoplastics
valves for industrial applications - Pressure
test methods and requirements - General
BS ISO 9831-1998 动物饲料、动物制品和粪便或尿液.总热量值测定.压力热量计法
Animal feeding stuffs, animal products, and
faeces or urine - Determination of gross calorific
value - Bomb calorimeter method
BS M 65-1987 压力补偿变量液压泵规范 Specification for pressure
compensated variable delivery hydraulic pumps
CP 312-2-1973 塑料管道(热塑材料)实用规程.第2部分:压力液体输送用非增塑PVC管
Code of practice for plastics pipework (thermoplastics
material). Unplasticized PVC pipework for the
conveyance of liquids under pressure
DD ENV 12108-2001 塑料管道系统.建筑物内部的人用冷热水压力管道系统的安装指南
Plastics piping systems. Guidance for the installation
inside buildings of pressure systems for hot
and cold water intended for human consumption
DD ENV 12291-1996 高技术陶瓷.大气压力高温下陶瓷复合材料的机械性能.压缩性能的测定
Advanced technical ceramics. Mechanical properties
of ceramic composites at high temperature in
air at atmospheric pressure. Determination of
compression properties
DD ENV 12789-1998 高技术陶瓷.大气压力高温情况下陶瓷复合物机械性能.挠性强度测定
Advanced technical ceramics. Mechanical properties
of ceramic composites at high temperature under
air at atmospheric pressure. Determination of
flexural strength
DD ENV 1401-2-2001 非压力地下废水排放和污水系统的塑料管道系统.非增塑聚氯乙烯.符合性评定指南
Plastics piping systems for non-pressure underground
drainage and sewerage. Unplasticized poly(vinylchloride)
(PVC-U). Guidance for assessment of conformity
DD ENV 1401-3-2001 非压力地下废水和排水系统的塑料管道系统.非增塑聚氯乙烯（PVC－U）.安装指南
Plastics piping systems for non-pressure underground
drainage and sewerage. Unplasticized poly(vinylchloride)
(PVC-U). Guidance for installation
DD ENV 1852-2-2001 非压力地下废水排放和污水系统的塑料管道系统.聚丙烯.符合性评定指南
Plastics piping systems for non-pressure underground
drainage and sewerage. Polypropylene (PP). Guidance
for the assessment of conformity
DD ENV 1893-1996 高技术陶瓷.在大气压力而又高温情况下陶瓷成分的机械性能.抗拉性能测定
Advanced technical ceramics. Mechanical properties
of ceramic composites at high temperature in
air at atmospheric pressure. Determination of
tensile properties
DD ENV 22605-1-1992 压力用钢制品.温升参数的导出和证明.第1部分:碳和低合金钢制品的屈服或试验应力
Steel products for pressure purposes. Derivation
and verification of elevated temperature properties.
Yield or proof stress of carbon and low alloy
steel products
DD ENV 22605-2-1992 压力用钢制品.温升特性的导出和证明.第2部分:奥氏体钢制品的试验应力
Steel products for pressure purposes. Derivation
and verification of elevated temperature properties.
Proof stress of austenitic steel products
DD ENV 22605-3-1992 压力用钢制品.温升特性的导出和证明.第3部分:当数据给定时导出温升屈服或试验应力特性的选择程序
Steel products for pressure purposes. Derivation
and verification of elevated temperature properties.
An alternative procedure for deriving the elevated
temperature yield or proof stress properties
when data are limited
KIT 111-2002 非燃烧的压力容器装置 Unfired pressure vessels
kit
PD 6525-1-1990 压力用钢的高温性能.第1部分:应力断裂性能 Elevated
temperature properties for steels for pressure
purposes. Stress rupture properties
TH 20344-2000 锅炉和压力容器.设计和批准要求的国际检验报告 Boilers
and Pressure Vessels - An international survey
of design and approval requirements
TH 42069-2000 压力容器.德国 Pressure Vessels: Germany
英国压力标准(BS pressure standards)
--------------------------------------------------------------------------------
编号 中文名称 英文名称
BIP 3055-2005 工作场所压力.实况.DVD Stress in the workplace
- The facts - DVD
BS 1101-1977 涂料和其他类似物质用压力容器规范 Specification
for pressure containers for paint and other
similar substances
BS 1377-6-1990 土木工程用土壤试验方法.第6部分:在液压压力盒内并且用孔隙压力测量进行固结和渗透率试验
Methods of test for soils for civil engineering
purposes - Consolidation and permeability tests
in hydraulic cells and with pore pressure measurement
BS 1428-D1-1965 微量化学仪器.第D 集:容量分析仪器.第1部分:带压力加注装置和自动回零的滴定管规范
Microchemical apparatus - Volumetric analysis
- Specification for burettes with pressure-filling
device and automatic zero
BS 1552-1995 压力可达200毫巴家庭用一类、二类和三类燃气敞口底部锥形旋塞阀规范
Specification for open bottomed taper plug valves
for 1st, 2nd and 3rd family gases up to 200
mbar
BS 1726-1-2002 用圆形线材和棒材制的圆柱形螺旋弹簧.规格、公差和测试指南.压力弹簧
Cylindrical helical springs made from round
wire and bar - Guide to methods of specifying,
tolerances and testing - Compression springs
BS 2000-0-0.4-1996 气压计压力校正 Barometric pressure
corrections
BS 2000-121-2005 石油及其产品的试验方法.从润滑脂中分离油的测定.压力过滤法
Methods of test for petroleum and its products
- Part 121: Determination of oil separation
from lubricating grease - Pressure filtration
method (Identical with IP 121:2005)
BS 2782-11 Method 1121B-1997 塑料的试验方法.第11部分:热塑管、接头和阀门.流体输送用热塑管.试验方法1121B:额定外部直径和额定压力.米
Methods of testing plastics - Thermoplastics
pipes, fittings and valves - Thermoplastics
pipes for the conveyance of fluids - Nominal
outside diameters and nominal pressures - Metric
series
BS 2782-11 Method 1121C-1997 塑料试验方法.第11部分:热塑管、接头和阀门.流体输送用热塑管.试验方法1121C:额定外部直径和额定压力.英尺
Methods of testing plastics - Thermoplastics
pipes, fittings and valves - Thermoplastics
pipes for the conveyance of fluids - Nominal
outside diameters and nominal pressures - Inch-based
series
BS 2782-11 Method 1127P-1997 塑料试验方法.第11部分:热塑管,接头和阀门.液体输送用热塑材管.试验方法1127P:抗内压力.试验方法
Methods of testing plastics - Thermoplastics
pipes, fittings and valves - Thermoplastics
pipes, for the conveyance of fluids - Resistance
to internal pressure - Test method
BS 2782-8 Method 821A-1979 塑料的试验方法.第8部分:其他性能.试验方法821A:在大气压力条件下薄片和薄膜透气率的测定(压力计)
Methods of testing plastics. Other properties.
Determination of the gas transmission rate of
films and thin sheets under atmospheric pressure
(manometric method)
BS 2C 11-1988 航空用压力舱的地面压力试验连接件规范 Specification
for ground pressure test connections for aircraft
pressure cabins
BS 2C 19-1994 新型压力重上油连接器规范 Specification for
pressure re-oiling connection (new type)
BS 2C 4-1973 飞机发动机制冷剂压力灌注接头尺寸规范 Specification
for coupling dimensions for aero-engine refrigerant
pressure replenishment connections
BS 2G 113-1956 飞行器用进气管压力表规范 Specification for
manifold pressure gauges for aircraft
BS 2G 117-1975 压力驱动空速指示器规范 Specification for
pressure-driven airspeed indicators
BS 2G 182-1975 航空用压力驱动马赫表规范 Specification for
pressure-driven machmeters for aircraft
BS 2G 201-1996 计数器和指示器压力高度计规范 Specification
for counter and pointer pressure altimeters
BS 3166-1959 温度范围为-20-220°F(-30-105℃)用温度记录器(注入液体型与蒸汽压力型)规范
Specification for thermographs (liquid-filled
and vapour pressure types) for use within the
temperature range -20 °F to 220 °F ( -30 °C
to 105 °C)
BS 3321-1986 织物的等效孔径测量方法(气泡压力试验) Method for
measurement of the equivalent pore size of fabrics
(bubble pressure test)
BS 3463-1975 压力容器水位观察和玻璃量杯规范 Specification for
observation and gauge glasses for pressure vessels
BS 3900-A22-1998 涂料的试验方法.第A22部分：用压力杯法对密度的测定
Methods of test for paints. Determination of
density by the pressure cup method
BS 3G 100-2.3.2-1970 飞机设备一般要求规范.第2部分:各种设备.第3节:环境条件.第2小节:温度压力要求
Specification for general requirements for equipment
for use in aircraft - All equipment - Environmental
conditions - Temperature-pressure requirements
BS 4151-1967 输入信号为 3至15磅/平方英寸(压力计)的气动阀定位器的评定方法
Method of evaluating pneumatic valve positioners
with input signal of 3 to 15 lbf/in2 (gauge)
BS 4172-1-1999 消灭室内飞虫用手持式压力气溶喷洒器.杀虫性能规范 Hand-held
pressurized aerosol dispensers against houseflies
- Specification for insecticidal performance
BS 4172-2-1999 消灭室内飞虫用手持式压力气溶喷洒器.杀虫性能的测定方法 Hand-held
pressurized aerosol dispensers against houseflies
- Method for determination of insecticidal performance
BS 4184-1994 开式机械型机动压力机词汇 Glossary for power
presses, open front mechanical type
BS 4346-3-1982 未增塑聚氯乙烯压力管的接头及配件.第3部分:溶粘剂规范 Joints
and fittings for use with unplasticized PVC
pressure pipes - Specification for solvent cement
BS 4361-30-1990 木工机械.第30部分:平滑表面手工上料平面胶合压力机命名
Woodworking machines - Nomenclature for hand-loading
veneering presses for flat surfaces
BS 4656-34-1985 机床精度及试验方法.第34部分:机械的开式机动压力机规范
Accuracy of machine tools and methods of test
- Specification for power presses, mechanical
open front type
BS 470-1984 压力容器检验孔、观察孔和入口孔规范 Specification
for inspection, access and entry openings for
pressure vessels
BS 4737-3.9-1978 擅入者报警系统规范.第3部分:元部件规范.第9节:压力传感垫
Intruder alarm systems - Specifications for
components - Pressure mats
BS 4742-3-1985 农用机械液压设备.第3部分:挂车用单动倾卸伸缩筒尺寸和额定压力规范
Hydraulic equipment for agricultural machinery
- Specification for dimensions and pressure
rating of single-acting telescopic tipping cylinders
for trailers
BS 4882-1990 法兰和保持压力用螺栓连接规范 Specification for
bolting for flanges and pressure containing
purposes
BS 4975-1990 核工程用预应力混凝土压力容器规范 Specification
for prestressed concrete pressure vessels for
nuclear engineering
BS 4C 14-1991 航空用压力加油连接器规范 Specification for
aircraft pressure refuelling connectors
BS 5045-8-2000 可运输的气瓶.特殊便携的在15℃时最高达300巴充气压力的水容量为0.5L-15L的无缝铝合金气瓶规范
Transportable gas containers - Specification
for seamless aluminium alloy gas containers
of water capacity 0.5 L up to 15 L and up to
300 bar charged pressure at 15 °C for special
portable application
BS 5173-102.8-1987 橡胶和塑料软管及软管组件试验方法.第102部分:液压试验.第8节:硬质增强热塑性塑料螺旋管压力脉冲试验
Methods of test for rubber and plastics hoses
and hose assemblies - Hydraulic pressure tests
- Pressure impulse test for rigid helix reinforced
thermoplastics hoses
BS 5276-1-1984 压力容器详细规格(尺寸).第1部分:钢容器支管盖吊杆规范
Pressure vessel details (dimensions) - Specification
for davits for branch covers of steel vessels
BS 5276-2-2003 压力容器细则(尺寸).卧式圆柱形压力容器鞍式支座规范 Pressure
vessel details (dimensions) - Specification
for saddle supports for horizontal cylindrical
pressure vessels
BS 5276-4-1977 压力容器详细规格(尺寸).第4部分:标准化压力容器 Pressure
vessel details (dimensions) - Standardized pressure
vessels
BS 5391-1-2006 丙烯腈-丁二烯-苯乙烯(ABS)压力管.规范 Acrylonitrile-butadiene-styrene
(ABS) pressure pipe - Specification
BS 5392-1-2006 用于丙烯腈-丁二烯-苯乙烯共聚物(ABS)压力管道的ABS配件.第1部分:规范
Acrylonitrile-butadiene-styrene (ABS) fittings
for use with ABS pressure pipe - Part 1: Specification
BS 5677-1979 采用互易技术对1英寸标准电容式传声器进行压力校准的精确方法 Method
(precision) for pressure calibration of one-inch
standard condenser microphones by the reciprocity
technique
BS 5886-1980 石棉水泥管路的现场压力试验方法 Methods for field
pressure testing of asbestos-cement pipelines
BS 5911-5-2004 混凝土管和辅助混凝土制品.带软接头的预应力非压力管道和配件的规范
Concrete pipes and ancillary concrete products
- Specification for prestressed non-pressure
pipes and fittings with flexible joints
BS 5944-4-1984 液压动力系统和部件空气噪音测量.第4部分:流量和压力控制阀声功率级测定方法
Measurement of airborne noise from hydraulic
fluid power systems and components - Method
of determining sound power levels from valves
controlling flow and pressure
BS 6069-5.1-1994 空气质量表征.第5部分:总则.第1节:温度、压力和湿度数据处理
Characterization of air quality - General -
Handling of temperature, pressure and humidity
data
BS 6129-1-1981 压力系统用波纹管膨胀节选用惯例.第1部分:金属波纹管膨胀节
Code of practice for the selection and application
of bellows expansion joints for use in pressure
systems - Metallic bellows expansion joints
BS 6134-1992 压力和真空开关规范 Specification for pressure
and vacuum switches
BS 6282-2-1982 防止回流水污染用带动件装置.第2部分:公称尺寸小于等于DN54的终端反压力阀规范
Devices with moving parts for the prevention
of contamination of water by backflow - Specification
for terminal anti-vacuum valves of nominal size
up to and including DN 54
BS 6282-4-1982 防止回流水污染用带动件装置.第4部分:公称尺寸小于等于DN42的组合单向阀和反压力阀规范
Devices with moving parts for the prevention
of contamination of water by backflow - Specification
for combined check and anti-vacuum valves of
nominal size up to and including DN 42
BS 6283-2-1991 热水系统安全控制装置.第2部分:压力范围从1bar到10bar的温度减压阀规范
Safety and control devices for use in hot water
systems - Specifications for temperature relief
valves for pressures from 1 bar to 10 bar
BS 6283-4-1991 热水系统中安全控制装置.第4部分:最大供给压力不超过12bar、标准尺寸不超过DN50的放松减压阀规范
Safety and control devices for use in hot water
systems - Specification for drop-tight pressure
reducing valves of nominal size up to and including
DN 50 for supply pressures up to and including
12 bar
BS 6356-2-1985 农作物防护用喷雾设备.第2部分:喷嘴与压力计连接尺寸规范
Spraying equipment for crop protection - Specification
for connecting dimensions for nozzles and manometers
BS 6400-2-2006 最大容量不超过6m<上标>3/h煤气表的安装、调换、重新定位和拆除用规范.中等压力(二类家用煤气)
Specification for installation, exchange, relocation
and removal of gas meters with a maximum capacity
not exceeding 6 m3/h - Medium pressure (2nd
family gases)
BS 6447-1984 输出电量的绝对压力发送器与表压发送器规范 Specification
for absolute and gauge pressure transmitters
with electrical outputs
BS 6448-1995 DN大于50的燃气调节器和进气口压力可达200mbar规范 Specification
for gas appliance governors of DN greater than
50 and for inlet pressures up to 200 mbar
BS 6590-1985 机械的开式压力机的额定功率和尺寸规范 Specification
for capacity ratings and dimensions of power
presses, mechanical open front type
BS 6944-1988 黑色金属(不包括压力管应用的)闪光对接焊规范 Specification
for flash welding of butt joints in ferrous
metals (excluding pressure piping applications)
BS 6979-1989 机动压力机的静载挠度的测量方法 Method for measurement
of static deflection of power presses
BS 7005-1988 蒸汽压缩致冷系统用碳钢非用火压力容器的设计和制造规范 Specification
for design and manufacture of carbon steel unfired
pressure vessels for use in vapour compression
refrigeration systems
BS 7068-1989 交变压力气垫规范 Specification for alternating
pressure air mattresses
BS 7372-3-1993 工业金属丝筛网和金属丝编织布孔径和丝径组合选择指南.第3部分:预压接或压力焊接金属丝筛网的优选组合
Guide to the choice of aperture size and wire
diameter combinations for industrial wire screens
and woven wire cloth - Preferred combinations
for pre-crimped or pressure-welded wire screens
BS 7403-1-1998 内燃机满液流润滑油过滤器.不同压力/流量特性试验方法 Full-flow
lubricating oil filters for internal combustion
engines - Methods of test for differential pressure/flow
characteristics
BS 7403-6-1991 内燃机用全流式润滑油过滤器.第6部分:静态爆裂压力的试验方法
Full-flow lubricating oil filters for internal
combustion engines - Method of test for static
burst pressure
BS 7504-1995 液压流体动力.在压力25 MPa 和40 MPa(250 巴
和400 巴)条件下使用的四螺钉、单片正方形法兰连接器 Hydraulic fluid
power - Four-screw, one-piece square flange
connections for use at pressures of 25 MPa and
40 MPa (250 bar and 400 bar)
BS 7527-2.3-1991 环境条件分类.第2部分:大自然呈现的环境条件.第3节:大气压力
Classification of environmental conditions -
Environmental conditions appearing in nature
- Air pressure
BS 7568-12-1992 冲压工具.第12部分:弹性体压力弹簧一般规范 Press
tools - Elastomer pressure springs - General
specification
BS 7568-13-1992 冲压工具.第13部分:弹性体压力弹簧.附件规范 Press
tools - Elastomer pressure springs - Specification
of accessories
BS 7707-1993 400kN-4000kN(含40000kN)公称力机械直边单作用型机动压力机规范
Specification for power presses, mechanical
straight-sided single-action type from 400 kN
up to and including 4000 kN nominal force
BS 7708-1993 250kN-400kN公称力的机械直边高速型机动压力机规范 Specification
for power presses, mechanical straight-sided
high-speed type of 250 kN up to 4000 kN nominal
force
BS 7727-1994 铜导体面积达6平方毫米(10AWG)电缆的预绝缘压力终端和连接器的安装和检测实用规程
Code of practice for installation and inspection
of pre-insulated compression terminals and connectors
for cables with copper conductors up to 6 mm2
BS 7847-1996 流体动力系统和部件.连接件和相关部件.标称压力 Fluid power
systems and components - Connectors and associated
components - Nominal pressures
BS 853-2-1996 供暖系统用压力容器规范.第2部分:建筑业和工业设施用管式热交换器和蓄热器
Specification for vessels for use in heating
systems - Tubular heat exchangers and storage
vessels for building and industrial services
BS AU 163a-1985 道路车辆用气压制动设备压力试验连接规范 Specification
for pressure test connection for compressed-air
pneumatic braking equipment for road vehicles
BS AU 50-3.1e-2002 轮胎和车轮.阀门.尺寸、名称与符号、使用中阀门压力等级和夹紧阀门扭矩
Tyres and wheels - Valves - Dimensions, designation,
valve pressure ratings by use and torque for
clamp-in valves
BS DD CEN/TS 13244-7-2004 排水和污水处理通用地下和地上压力设备用塑料管道系统.聚乙烯(PE).符合性评定指南
Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
Guidance for the assessment of conformity
BS DD CEN/TS 14541-2007 非压力设备用塑料管道和配件.非原态未增塑聚氯乙烯、聚丙烯和聚乙烯材料应用
Plastics pipes and fittings for non-pressure
applications - Utilisation of non-virgin PVC-U,
PP and PE materials
BS DD CEN/TS 1456-2-2003 压力下直埋式和地上排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U).合格评定指南
Plastic piping systems for buried and above-ground
drainage and sewerage under pressure - Unplasticized
poly(vinyl chloride) (PVC-U) - Guidance for
the assessment of conformity
BS DD CEN/TS 14632-2006 排水、排污和供水、压力和非压力用塑料管道系统.基于聚酯树脂(UP)玻璃纤维增强热固性塑料(GPR).合格评定指
Plastics piping systems for drainage, sewerage
and water supply, pressure and non-pressure
- Glass-reinforced thermosetting plastics (GRP)
based on polyester resin (UP) - Guidance for
the assessment of conformity
BS DD CEN/TS 14758-3-2006 无压力地下排水和排污塑料管道系统.聚丙烯矿物调节器(s)(PP-MD).安装指南
Plastics piping systems for non-pressure underground
drainage and sewerage - Polypropylene with mineral
modifier(s)(PP-MD) - Guidance for installation
BS DD CEN/TS 1591-4-2007 法兰及其连接件.带垫圈圆形法兰连接件的设计原则.符合压力设备指令的螺栓连接件装配职工能力的合格鉴定
Flanges and their joints - Design rules for
gasketed circular flange connections - Qualification
of personnel competency in the assembly of bolted
joints fitted to equipment subject to the Pressure
Equipment Directive
BS DD CEN/TS 1852-3-2003 非压力地下排水和排污塑料管道系统.聚丙烯(PP).安装指南
Plastics piping systems for non-pressure underground
drainage and sewerage - Polypropylene (PP) -
Guidance for installation
BS DD CEN/TS 764-6-2004 压力设备.操作说明书的结构和内容 Pressure
equipment - Structure and content of operating
instructions
BS DD ENV 12108-2001 塑料管道系统.建筑物内部人消费用冷热水的压力系统的安装指南
Plastics piping systems - Guidance for the installation
inside buildings of pressure systems for hot
and cold water intended for human consumption
BS DD ENV 13050-2001 幕墙.水密封性.空气压力和水喷射动态条件下的实验室试验
Curtain walling - Watertightness - Laboratory
test under dynamic condition of air pressure
and water spray
BS DD ISO/TS 17996-2006 乳酪.以恒定位移速率的单轴压力测定流变特性
Cheese - Determination of rheological properties
by uniaxial compression at constant displacement
rate
BS EN 10028-1-2000 压力容器用的钢板制品规范.一般要求 Specification
for flat products made of steels for pressure
purposes - General requirements
BS EN 10028-3-2003 压力容器用的扁平钢轧材规范.经正火处理的可焊细粒钢
Specification for flat products made of steels
for pressure purposes - Weldable fine grain
steels, normalized
BS EN 10028-5-2003 压力容器用的扁平钢轧材规范.热机轧制可焊细粒钢 Specification
for flat products made of steels for pressure
purposes - Weldable fine grain steels, thermomechanically
rolled
BS EN 10028-6-2003 压力用的扁平钢轧材规范.淬火和回火可焊细粒钢 Specification
for flat products made of steels for pressure
purposes - Weldable fine grain steels, quenched
and tempered
BS EN 10028-7-2000 承受压力用的平钢板制品规范.不锈钢 Flat products
made of steels for pressure purposes - Stainless
steels
BS EN 10207-2005 简单压力容器用钢材.板材、带材和棒材交货技术要求 Steels
for simple pressure vessels - Technical delivery
requirements for plates, strips and bars
BS EN 10213-1-1996 压力用途的钢铸件交付技术状态.总则 Technical
delivery conditions for steel castings for pressure
purposes - General
BS EN 10213-2-1996 压力用途的钢铸件的交付技术状态.第2部分:环境温度和高温下使用钢的等级
Technical delivery conditions for steel castings
for pressure purposes - Steel grades for use
at room temperature and at elevated temperature
BS EN 10213-3-1996 压力用途的钢铸件交付技术状态.低温下使用的钢 Technical
delivery conditions for steel castings for pressure
purposes - Steels for use at low temperatures
BS EN 10213-4-1996 压力用途的钢铸件的交付技术状态.第4部分:奥氏体钢和奥氏体-铁素体钢的等级
Technical delivery conditions for steel castings
for pressure purposes - Austenitic and austenitic-ferritic
steel grades
BS EN 10216-5-2004 压力无缝钢管.交货技术条件.无缝钢管 Seamless
steel tubes for pressure purposes - Technical
delivery conditions - Stainless steel tubes
BS EN 10217-7-2005 压力用途焊接钢管.交货技术条件.不锈钢管 Welded
steel tubes for pressure purposes - Technical
delivery conditions - Stainless steel tubes
BS EN 10222-2-2000 压力容器用钢锻件.具有规定升温特性的铁素体钢和马口铁钢
Steel forgings for pressure purposes - Ferritic
and martensitic steels with specified elevated
temperature properties
BS EN 10222-3-1999 压力容器用钢锻件.具有特定低温特性的镍钢 Steel
forgings for pressure purposes - Nickel steels
with specified low-temperature properties
BS EN 10222-4-1999 压力容器用钢锻件.具有高验收强度的可焊接细晶粒钢
Steel forgings for pressure purposes - Weldable
fine-grain steels with high proof strength
BS EN 10222-5-2000 压力容器用钢锻件.马口铁钢,奥氏体钢,奥氏体-铁素体不锈钢
Steel forgings for pressure purposes - Martensitic,
austenitic and austenitic-ferritic stainless
steels
BS EN 10226-1-2004 螺纹上有压力密封接缝的管螺纹.锥形外螺纹和平行内螺纹.尺寸、公差及名称与符号
Pipe threads where pressure tight joints are
made on the threads - Taper external threads
and parallel internal threads - Dimensions,
tolerances and designation
BS EN 10226-2-2005 螺纹上压力强密联接的管螺纹.第2部分:锥形外螺纹和锥形内螺纹.尺寸、公差及名称和符号
Pipe threads where pressure tight joints are
made on the threads - Part 2: Taper external
threads and taper internal threads - Dimensions,
tolerances and designation
BS EN 10226-3-2005 螺纹上有压力密封接缝的管螺纹.用极限量规验证 Pipe
threads where pressure-tight joints are made
on the threads - Verification by means of limit
gauges
BS EN 10243-1-1999 钢模锻.公差和尺寸.落锤或垂直压力锻造 Steel
die forgings - Tolerances on dimensions - Drop
and vertical press forgings
BS EN 10273-2000 特定高温性能压力用热轧可焊接钢棒 Hot rolled
weldable steel bars for pressure purposes with
specified elevated temperature properties
BS EN 1053-1996 塑料管道系统.无压力情况下使用的热塑管道系统.防水性的检验方法
Plastics piping systems - Thermoplastics piping
systems for non-pressure applications - Test
methods for watertightness
BS EN 12007-1-2000 燃气供应系统.最大工作压力达到和超过16巴的管线.通用功能推荐值
Gas supply systems - Pipelines for maximum operating
pressure up to and including 16 bar - General
functional recommendations
BS EN 12007-2-2000 燃气供应系统.最大工作压力达到和超过16巴的管线.聚乙烯特定功能推荐值
Gas supply systems - Pipelines for maximum operating
pressure up to and including 16 bar - Specific
functional recommendations for polyethylene
(MOP up to and including 10 bar)
BS EN 12007-3-2000 燃气供应系统.最大工作压力达到和超过16巴的管线.钢特定功能推荐值
Gas supply systems - Pipelines for maximum operating
pressure up to and including 16 bar - Specific
functional recommendations for steel
BS EN 12007-4-2000 燃气供应系统.最大工作压力达到和超过16巴的管线.修复的特定功能推荐值
Gas supply systems - Pipelines for maximum operating
pressure up to and including 16 bar - Specific
functional recommendations for renovation
BS EN 12046-2-2000 操作压力.试验方法.门 Operating forces
- Test method - Doors
BS EN 12094-10-2003 固定消防系统.气体灭火系统元件.压力计和压力开关的试验方法和要求
Fixed firefighting systems - Components for
gas extinguishing systems - Requirements and
test methods for pressure gauges and pressure
switches
BS EN 12106-1998 塑料管道系统.聚乙稀(PE)阀门.挤压后抗内压力的试验方法
Plastics piping systems - Polyethylene (PE)
pipes - Test method for the resistance to internal
pressure after application of squeeze-off
BS EN 12155-2000 幕墙.水密性.静态压力下的实验室试验 Curtain
walling - Watertightness - Laboratory test under
static pressure
BS EN 12266-1-2003 工业用阀门.阀门试验.压力试验、试验规程和验收标准.强制要求
Industrial valves - Testing of valves - Pressure
tests, test procedures and acceptance criteria
- Mandatory requirements
BS EN 1229-1997 塑料管道系统.玻璃增强的热固性塑料管.验证短期内部压力下墙的密封性试验方法
Plastics piping systems - Glass-reinforced thermosetting
plastics (GRP) pipes and fittings - Test methods
to prove the leaktightness of the wall under
short-term internal pressure
BS EN 12291-2004 高级工业陶瓷.大气压力下高温空气中陶瓷复合材料的机械性能.压缩特性的测定
Advanced technical ceramics - Mechanical properties
of ceramic composites at high temperature in
air at atmospheric pressure - Determination
of compression properties
BS EN 12295-2000 塑料管道系统.热水和冷水用热塑管和附属配件.连接件耐压力变化的试验方法
Plastics piping systems - Thermoplastics pipes
and associated fittings for hot and cold water
- Test method for resistance of joints to pressure
cycling
BS EN 12327-2000 燃气供应系统.压力试验,交付使用和非交付使用过程.功能要求
Gas supply systems - Pressure testing, commissioning
and decommissioning procedures - Functional
requirements
BS EN 12350-7-2000 新浇混凝土试验.空气含量.压力法 Testing
fresh concrete - Air content - Pressure methods
BS EN 12365-2-2003 建筑五金.门、窗、百叶窗和幕墙用衬垫及挡风雨条.线性压力试验方法
Building hardware - Gasket and weatherstripping
for doors, windows, shutters and curtain walling
- Linear compression force test methods
BS EN 12392-2000 铝和铝合金.锻压产品.生产压力设备用产品专门要求 Aluminium
and aluminium alloys - Wrought products - Special
requirements for products intended for the production
of pressure equipment
BS EN 1254-4-1998 铜和铜合金.管路接头.与带有毛细管或压力端头的其它端头连接的管接头
Copper and copper alloys - Plumbing fittings
- Fittings combining other end connections with
capillary or compression ends
BS EN 12541-2003 卫生设备配件.压力冲洗阀和自动关闭便池冲水阀PN10
Sanitary tapware - Pressure flushing valves
and automatic closing urinal valves PN 10
BS EN 12561-3-2003 铁路设施.油罐车.压力下液化气用底部装卸装置 Railway
applications - Tank wagons - Bottom filling
and emptying devices for gases liquefied under
pressure
BS EN 12621-2006 压力下覆层材料的供应和循环用机器.安全要求 Machinery
for the supply and circulation of coating materials
under pressure - Safety requirements
BS EN 12645-1999 压力量规.机动车轮胎膨胀和/或压力检验设备.计量学,要求和试验
Pressure gauges - Apparatus for inspection of
pressure and/or inflation of tyres for motor
vehicles - Metrology, requirements and testing
BS EN 12666-1-2005 无压力地下排水和排污塑料管道系统.聚乙烯(PE).管、管件和系统的规范
Plastics piping systems for non-pressure underground
drainage and sewerage - Polyethylene (PE) -
Part 1: Specifications for pipes, fittings and
the system
BS EN 12697-25-2005 沥青混合料.热混沥青的试验方法.循环压力试验 Bituminous
mixtures - Test methods for hot mix asphalt
- Cyclic compression test
BS EN 12778-2002 烹饪器具.家用压力锅 Cookware - Pressure
cookers for domestic use
BS EN 12864-2001 丁烷、丙烷或其混合物用最大出口压力≤200mbar、液流量≤4kg/h的低压不可调的调节器及其相关的安全装置
Low-pressure, non adjustable regulators having
a maximum outlet pressure of less than or equal
to 200 mbar, with a capacity of less than or
equal to 4 kg/h, and their associated safety
devices for butane, propane or their mixtures
BS EN 12865-2001 建筑构件和建筑元件的湿温性能.在空气辅助压力下外墙抗暴雨力的测定
Hygrothermal performance of building components
and building elements - Determination of the
resistance of external wall systems to driving
rain under pulsating air pressure
BS EN 12952-2-2002 水管锅炉和辅助设备.第2部分:锅炉和附件的压力零件用材料
Water-tube boilers and auxiliary installations
- Materials for pressure parts of boilers and
accessories
BS EN 12952-3-2002 水管锅炉和辅助设备.压力零件的设计和计算 Water-tube
boilers and auxiliary installations - Design
and calculation of pressure parts
BS EN 12952-5-2002 水管锅炉和辅助设备.第5部分:锅炉压力部件的工艺和制造
Water-tube boilers and auxiliary installations
- Workmanship and construction of pressure parts
of the boiler
BS EN 12952-6-2002 水管锅炉和辅助设备.锅炉压力部件在生产过程中的检验,文献工作和作标记
Water-tube boilers and auxiliary installations
- Inspection during construction, documentation
and marking of pressure parts of the boiler
BS EN 12953-2-2002 火管锅炉.锅炉和附件用的压力零件材料 Shell
boilers - Materials for pressure parts of boilers
and accessories
BS EN 12953-3-2002 火管锅炉.压力零件的设计和计算 Shell boilers
- Design and calculation for pressure parts
BS EN 12953-4-2002 火管锅炉.锅炉的压力零件的工艺和制造 Shell
boilers - Workmanship and construction of pressure
parts of the boiler
BS EN 12953-5-2002 火管锅炉.锅炉的压力零件的制造、文献汇编和作标记过程的检查
Shell boilers - Inspection during construction,
documentation and marking of pressure parts
of the boiler
BS EN 12953-8-2002 火管锅炉.第8部分:防过量压力的安全保护装置的要求
Shell boilers - Requirements for safeguards
against excessive pressure
BS EN 13016-1-2007 液化石油产品.蒸气压力.气体饱和蒸气压(ASVP)的测定和干蒸气压当量值(DVPE)的计算
Liquid petroleum products - Vapour pressure
- Determination of air saturated vapour pressure
(ASVP) and calculated dry vapour pressure equivalent
(DVPE)
BS EN 13016-2-2007 液化石油产品.蒸气压力.40℃和100℃之间的绝对蒸气压(AVP)的测定
Liquid petroleum products - Vapour pressure
- Determination of absolute vapour pressure
(AVP) between 40 °C and 100 °C
BS EN 13042-5-2003 空心玻璃生产、处理和加工用机械和设备.安全要求.压力机
Machines and plants for the manufacture, treatment
and processing of hollow glass - Safety requirements
- Presses
BS EN 13094-2004 危险物品运输用槽罐.工作压力不超过0.5bar的金属槽罐.设计和建造
Tanks for the transport of dangerous goods -
Metallic tanks with a working pressure not exceeding
0,5 bar - Design and construction
BS EN 13160-2-2003 检漏系统.压力和真空系统 Leak detection
systems - Pressure and vacuum systems
BS EN 13244-1-2003 一般用途、排水和排污水的地下或地面压力系统用塑料管道系统.聚乙烯.总则
Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
General
BS EN 13244-2-2003 一般用途、排水和排污水的地下或地面压力系统用塑料管道系统.聚乙烯.管道
Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
Pipes
BS EN 13244-3-2003 一般用途、排水和排污水的地下或地面压力系统用塑料管道系统.聚乙烯.配件
Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
Fittings
BS EN 13244-4-2003 一般用途、排水和排污水的地下或地面压力系统用塑料管道系统.聚乙烯.阀门
Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
Valves
BS EN 13244-5-2003 一般用途、排水和排污水的地下或地面压力系统用塑料管道系统.聚乙烯.系统目的的适合性
Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
Fitness for purpose of the system
BS EN 13308-2002 危险物品运输用槽罐车.槽罐车用辅助设备.无压力平衡底阀
Tanks for transport of dangerous goods - Service
equipment for tanks - Non pressure balanced
footvalve
BS EN 13311-3-2001 生物技术.容器的性能标准.玻璃压力容器 Biotechnology
- Performance criteria for vessels - Glass pressure
vessels
BS EN 13316-2002 危险物品运输用槽罐车.槽罐车用辅助设备.压力平衡底阀
Tanks for transport of dangerous goods - Service
equipment for tanks - Pressure balanced footvalve
BS EN 13445-1-2002 非燃烧压力容器.总则 Unfired pressure
vessels - General
BS EN 13445-2-2002 非燃烧压力容器.材料 Unfired pressure
vessels - Materials
BS EN 13445-3-2002 无烧火的压力容器.设计 Unfired pressure
vessels - Design
BS EN 13445-4-2002 非燃烧压力容器.制造 Unfired pressure
vessels - Fabrication
BS EN 13445-5-2002 非燃烧压力容器.检测和试验 Unfired pressure
vessels - Inspection and testing
BS EN 13445-6-2002 非燃烧压力容器.球形石墨铸铁制压力容器和压力零部件的设计和生产要求
Unfired pressure vessels - Requirements for
the design and fabrication of pressure vessels
and pressure parts constructed from spheroidal
graphite cast iron
BS EN 13445-8-2006 非受火压力容器.铝和铝合金压力容器附加要求 Unfired
pressure vessels - Additional requirements for
pressure vessels of aluminium and aluminium
alloys
BS EN 13523-24-2004 卷材覆层金属.试验方法.耐粘结性和压力标记 Coil
coated metals - Test methods - Resistance to
blocking and pressure marking
BS EN 13562-2000 土工织物及其相关产品.抗水渗透性测定(液体静压力试验)
Geotextiles and geotextile-related products
- Determination of resistance to penetration
by water (hydrostatic pressure test)
BS EN 13566-2-2005 地下非压力排水和排污网修缮用塑料管道系统.第2部分:连续管加衬
Plastics piping systems for renovation of underground
non-pressure drainage and sewerage networks
— Part 2: Lining with continuous pipes
BS EN 13589-2004 石油及其制品的试验方法.沥青和沥青粘合剂.用压力延展法测定改性沥青的拉伸性能
Methods of test for petroleum and its products
- Bitumen and bituminous binders - Determination
of the tensile properties of modified bitumen
by the force ductility method
BS EN 13598-1-2003 无压力地下排水和排污用塑料管道系统.未增塑聚氯乙烯(PVC-U)、聚丙烯(PP)和聚乙烯(PE).第1部分:包括浅层检
Plastics piping systems for non-pressure underground
drainage and sewerage - Unplasticized poly(vinyl
chloride) (PVC-U), polypropylene (PP) and polyethylene
(PE) - Specifications for ancillary fittings
including shallow inspection chambers
BS EN 13631-6-2003 民用爆炸物.烈性炸药.测定抗液体静压力 Explosives
for civil uses - High explosives - Determination
of resistance to hydrostatic pressure
BS EN 13673-1-2003 气体和蒸气的最大爆炸压力和最大压升的测定.最大爆炸压力的测定
Determination of the maximum explosion pressure
and the maximum rate of pressure rise of gases
and vapours - Determination of the maximum explosion
pressure
BS EN 13673-2-2005 气体和蒸气的最大爆炸压力和最大压升速率的测定.最大爆炸压升速率的测定
Determination of maximum explosion pressure
and the maximum rate of pressure rise of gases
and vapours - Determination of the maximum rate
of explosion pressure rise
BS EN 13736-2003 机床安全.气动压力机 Safety of machine
tools - Pneumatic presses
BS EN 13763-12-2003 民用爆炸物.雷管和传爆管.耐静水压力的测定 Explosives
for civil uses - Detonators and relays - Determination
of resistance to hydrostatic pressure
BS EN 13774-2003 最大工作压力小于或等于16巴的配气系统用阀门.性能要求
Valves for gas distribution systems with maximum
operating pressure less than or equal to 16
bar - Performance requirements
BS EN 13785-2005 丁烷、丙烷或其混合物用容量100 kg/h及以下和最大输出压力4巴及以下的调节器.不包括EN
12864中设备及其相关 Regulators with a capacity of up
to and including 100 kg/h, having a maximum
nominal outlet pressure of up to and including
4 bar, other than those covered by EN 12864
and their associated safety devices for butane,
propane or their mixtures
BS EN 13786-2004 丁烷、丙烷或它们的混合物用最大输出压力4巴及以下和100
kg/h及以下容积的自动转换阀及其相关安全设备 Automatic change-over
valves having a maximum outlet pressure of up
to and including 4 bar with a capacity of up
to and including 100 kg/h, and their associated
safety devices for butane, propane or their
mixtures
BS EN 13787-2001 入口压力达100巴的气体压力调节器及相关安全装置的弹性体.
Elastomers for gas pressure regulators and associated
safety devices for inlet pressures up to 100
bar
BS EN 13923-2005 丝绕制FRP压力容器.材料、设计、制造和测试 Filament-wound
FRP pressure vessels - Materials, design, manufacturing
and testing
BS EN 14025-2004 危险物品运输用容器.金属压力容器.设计和制造 Tanks
for the transport of dangerous goods - Metallic
pressure tanks - Design and construction
BS EN 14034-1-2005 尘云的爆炸特性测定.尘云最大爆炸压力pmax的测定
Determination of explosion characteristics of
dust clouds - Determination of the maximum explosion
pressure pmax of dust clouds
BS EN 14034-2-2006 尘云爆炸特性的测定.尘云爆炸压力上升的最大比率(dp/dt)的测定
Determination of explosion characteristics of
dust clouds - Determination of the maximum rate
of explosion pressure rise (dp/dt) max of dust
clouds
BS EN 14208-2004 可移动式储气瓶.气体运输用容量最高达1000升的焊接的压力桶规范.设计和建造
Transportable gas cylinders - Specification
for welded pressure drums up to 1000 litre capacity
for the transport of gases - Design and construction
BS EN 14276-1-2006 制冷系统和热泵用压力设备.压力容器.一般要求 Pressure
equipment for refrigerating systems and heat
pumps - Vessels - General requirements
BS EN 14276-2-2007 制冷系统和热泵用压力设备.管道.一般要求 Pressure
equipment for refrigerating systems and heat
pumps - Piping - General requirements
BS EN 14289-2004 皮革.物理和机械试验.水渗透压力的测定 Leather
- Physical and mechanical tests - Determination
of water penetration pressure
BS EN 14364-2006 地下压力排水和排污水塑料管道系统.未饱和聚酯树脂(UP)玻璃纤维增强的热固性塑料(GRP).管道、配件和连接件
Plastic piping systems for drainage and sewerage
with or without pressure - Glass reinforced
thermosetting plastics (GRP) based on unsaturated
polyester resin (UP) - Specifications for pipes,
fittings and joints
BS EN 14367-2005 不同压力区的非控制回流阻件.A型C族 Non controllable
backflow preventer with different pressure zones
- Family C, type A
BS EN 14382-2002 气压调节站和装置用安全设备.运行压力在100巴以下的气体安全关闭装置
Safety devices for gas pressure regulating stations
and installations - Gas safety shut-off devices
for operating pressure up to 100 bar
BS EN 14382-2005 气压调节站和装置用安全设备.进气口压力不超过100bar的气体安全截止装置
Safety devices for gas pressure regulating stations
and installations - Gas safety shut-off devices
for inlet pressures up to 100 bar
BS EN 14423-2004 额定压力到18bar的蒸汽软管用夹具型连接组件 Clamp
type coupling assemblies for use with steam
hoses rated for pressures up to 18 bar
BS EN 14452-2005 防饮用水回流污染的装置.带大气出口和活动部件公称压力DN10～DN20的管阻流器.B型D系列
Devices to prevent pollution by backflow of
potable water — Pipe interrupter with atmospheric
vent and moving element DN 10 to DN 20 — Family
D, type B
BS EN 14453-2005 防止饮用水回流污染的装置.带恒定大气压力孔DN 10～DN
20的管阻流器.C型D系列 Devices to prevent pollution by
backflow of potable water - Pipe interrupter
with permanent atmospheric vent DN 10 to DN
20 - Family D , type C
BS EN 14513-2005 可移动储气瓶.防爆板压力释放装置(不含乙炔储气瓶) Transportable
gas cylinders - Bursting disc pressure relief
devices (excluding acetylene gas cylinders)
BS EN 14584-2005 无损检验.声学辐射.验收试验过程中金属压力设备的检查.AE源的平面位置
Non-destructive testing - Acoustic emission
- Examination of metallic pressure equipment
during proof testing - Planar location of AE
sources
BS EN 14585-1-2006 压力设备用金属波纹软管组件.要求 Corrugated
metal hose assemblies for pressure applications
- Requirements
BS EN 14595-2005 危险物品运输罐.罐的辅助设备.压力和真空通气口 Tanks
for transport of dangerous goods - Service equipment
for tanks - Pressure and vacuum breather vent
BS EN 14627-2005 食品.痕量元素的测定.压力分解后用氢化法原子吸收光谱测定法测定硒和砷的总含量
Foodstuffs - Determination of trace elements
- Determination of total arsenic and selenium
by hydride generation atomic absorption spectrometry
(HGAAS) after pressure digestion
BS EN 14680-2006 非压力热塑管道系统用粘合剂.规范 Adhesives
for non-pressure thermoplastic piping systems
- Specifications
BS EN 14741-2006 热塑管和管道系统.非压力掩埋用接头.通过评估密封压力测定弹性密封件接合处的长期密封性能的试验方法
Thermoplastics piping and ducting systems -
Joints for buried non-pressure applications
- Test method for the long-term sealing performance
of joints with elastomeric seals by estimating
the sealing pressure
BS EN 14758-1-2005 无压力地下排水和污水用塑料管道系统.含矿物调节剂的聚丙烯(PP-MD).第1部分:管、配件和系统用规范.
Plastics piping systems for non-pressure underground
drainage and sewerage - Polypropylene with mineral
modifiers (PP-MD) - Part 1: Specifications for
pipes, fittings and the system
BS EN 14769-2006 石油及其产品的试验方法.沥青和沥青粘合剂.用压力老化容器(PAV)寻求加速长期老化的条件
Methods of test for petroleum and its products
- Bitumen and bituminousbi nders - Accelerated
long-term ageing conditioning by a pressure
ageingves sel (PAV)
BS EN 14801-2006 水和废水管道用产品的压力分类条件 Conditions
for Pressure Classification of Products for
Water andWastewater Pipelines
BS EN 14814-2007 压力下流体热塑性管道系统用胶粘剂.规范 Adhesives
for thermoplastic piping systems for fluids
under pressure - Specifications
BS EN 14876-2007 可运输储气瓶.定期检验和焊接钢压力桶试验 Transportable
gas cylinders - Periodic inspection and testing
of welded steel pressure drums
BS EN 14893-2006 液化石油气设备和附件.容量为150升～1000升可运输液化石油气(LPG)的焊接钢压力桶
LPG equipment and accessories - Transportable
liquefied petroleum gas (LPG) welded steel pressure
drums with a capacity between 150 litres and
1000 litres
BS EN 1490-2000 建筑物阀门.温度和压力结合型的释放阀门.试验和要求 Building
valves - Combined temperature and pressure relief
valves - Tests and requirements
BS EN 15266-2007 建筑物中工作压力等于0.5bar的气体用不锈钢柔性波管工具
Stainless steel pliable corrugated tubing kits
in buildings for gas with an operating pressure
up to 0,5 bar
BS EN 153000-1998 电子元器件质量评定协调体系.通用规范.分立压力接触电源半导体装置(合格鉴定批准)
Harmonized system of quality assessment for
electronic components - Generic specification:
discrete pressure contact power semiconductor
devices (qualification approval)
BS EN 15550-2007 动物饲料.压力消解后用石墨炉原子吸收光谱法(GF-AAS)测定镉和铅含量
Animal feeding stuffs - Determination of cadmium
and lead by graphite furnace atomic absorption
spectrometry (GF-AAS) after pressure digestion
BS EN 1594-2000 燃气供应系统.最大工作压力超过16巴的气体管道.功能要求
Gas supply systems - Pipelines for maximum operating
pressure over 16 bar - Functional requirements
BS EN 1595-1997 硼硅酸盐玻璃3.3制压力设备.设计、制造和试验一般规则
Pressure equipment made from borosilicate glass
3.3. General rules for design, manufacture and
testing
BS EN 1605-1997 建筑物用的隔热产品.在特定压力负载和温度条件下变形的测定.
Thermal insulating products for building applications
- Determination of deformation under specified
compressive load and temperature conditions
BS EN 1653-1998 铜和铜合金.锅炉、压力容器和热水保温装置用的板、薄板材和圆形材
Copper and copper alloys - Plate, sheet and
circles for boilers, pressure vessels and hot
water storage units
BS EN 1671-1997 建筑物外压力污水系统 Pressure sewerage
systems outside buildings
BS EN 1760-1-1998 机械安全.压力敏感防护装置.压力敏感垫和压力敏感地板的设计和试验通用规则
Safety of machinery - Pressure sensitive protective
devices - General principles for the design
and testing of pressure sensitive mats and pressure
sensitive floors
BS EN 1775-2007 燃气供应.建筑物用燃气管道.最大工作压力不超过或等于5巴.功能推荐标准
Gas supply - Gas pipework for buildings - Maximum
operating pressure less than or equal to 5 bar
- Functional recommendations
BS EN 1796-2006 有或无压力供水塑料管道系统.基于不饱和聚酯(UP)的玻璃增强热固塑料(GRP)
Plastics piping systems for water supply with
or without pressure - Glass-reinforced thermosetting
plastics (GRP) based on unsaturated polyester
resin (UP)
BS EN 1854-2006 气体燃烧器和燃气器具的压力敏感装置 Pressure sensing
devices for gas burners and gas burning appliances
BS EN 1893-2005 高级工业陶瓷.大气压力下空气中高温情况下陶瓷成分的机械特性.拉伸特性的测定
Advanced technical ceramics - Mechanical properties
of ceramic composites at high temperature in
air at atmospheric pressure - Determination
of tensile properties
BS EN 1894-2005 高级工业陶瓷.惰性气体环境中高温情况下陶瓷成分的机械特性.通过有凹槽试样的压力荷载测定剪切强度
Advanced technical ceramics - Mechanical properties
of ceramic composites at high temperature under
inert atmosphere - Determination of shear strength
by compression loading of notched specimens
BS EN 1989-2000 热塑管道系统.地下埋装的非承压污水设施用连接件.通过对密封压力的估计对带热塑弹力密封件的连接件的长期密
Thermoplastics piping systems - Joints for buried
non-pressure sewerage applications - Test method
for long-term sealing performance of joints
with thermoplastic elastomer (TPE) seals by
estimating the sealing pressure
BS EN 200-1992 卫生用水龙头.单一和混合水龙头(标称尺寸1/2)PN10通用技术规范.最小流动压力0.05MPa(0.5bar)
Sanitary tapware - General technical specifications
for single taps and mixer taps (nominal size
1/2) PN 10 - Minimum flow pressure of 0.05 MPa
(0.5 bar)
BS EN 20811-1982 纺织品.耐水渗透性的测定.静水压力试验 Textiles
- Determination of resistance to water penetration
- Hydrostatic pressure test
BS EN 22858-1993 端吸式离心泵(额定压力16巴).命名、标称效率点和尺寸
End-suction centrifugal pumps (rating 16 bar)
- Designation, nominal duty point and dimensions
BS EN 23035-1994 单面和单壁瓦楞纤维纸板耐压力的测定定 Single-faced
and single-wall corrugated fibreboard - Determination
of flat crush resistance
BS EN 2624-2007 航空航天系列.水压系统元件的压力脉冲测试 Aerospace
series - Pressure impulse testing of hydraulic
system components
BS EN 278-1991 采用压力达200毫巴可燃气体的家用器具膜片用橡胶材料规范
Specification for rubber materials for diaphragms
in domestic appliances using combustible gases
up to 200 mbar
BS EN 279-1991 使用压力达200毫巴可燃气体的家用器具的动态密封件用均质橡胶材料规范
Specification for homogenous rubber materials
for dynamic seals in domestic appliances using
combustible gases up to 200 mbar
BS EN 286-1 1998 + A2-1998 罐装空气或氮气用非受火简易压力容器.通用压力容器
Simple unfired pressure vessels designed to
contain air or nitrogen - Pressure vessels for
general purposes
BS EN 286-1-1998 专用于空气或氮气的简单非受火压力容器.一般用途压力容器
Simple unfired pressure vessels designed to
contain air or nitrogen - Pressure vessels for
general purposes
BS EN 286-2-1992 装空气或氮气用简单不用火加热的压力容器.汽车和拖车气动刹车和辅助系统用压力容器规范
Simple unfired pressure vessels designed to
contain air or nitrogen - Specification for
pressure vessels for air braking and auxiliary
systems for motor vehicles and their trailers
BS EN 286-3-1995 装空气或氮气用的不用火加热的一般压力容器.第3部分:用于铁路运输车辆空气制动和辅助气动设备的钢制压力容
Simple unfired pressure vessels designed to
contain air or nitrogen - Steel pressure vessels
designed for air braking equipment and auxiliary
pneumatic equipment for railway rolling stock
BS EN 286-4-1995 装空气或氮气用的不点火加热的一般压力容器.第4部分:用于铁路运输车辆空气制动和辅助气动设备的铝合金压力
Simple unfired pressure vessels designed to
contain air or nitrogen - Aluminium alloy pressure
vessels designed for air braking equipment and
auxiliary pneumatic equipment for railway rolling
stock
BS EN 289-2004 塑料和橡胶机械.压力机.安全要求 Plastics and
rubber machines - Presses - Safety requirements
BS EN 291-1992 压力为200毫巴及其以下的家用可燃气体静态密封用橡胶密封件的材料规范
Rubber seals - Static seals in domestic appliances
for combustible gas up to 200 mbar - Specification
for material
BS EN 293-1992 油压力雾化喷嘴.最低要求.试验 Specification
for oil pressure atomizing nozzles - Minimum
requirements - Testing
BS EN 3-8-2006 便携式灭火器.第8部分:对EN 3-7的最大允许压力≤30bar灭火器的结构、耐压和机械试验的附加要求
Portable fire extinguishers - Part 8: Additional
requirements to EN 3-7 for the construction,
resistance to pressure and mechanical tests
for extinguishers with a maximum allowable pressure
equal to or lower than 30 bar
BS EN 303-4-1999 供暖锅炉.带强制通风燃烧器的供暖锅炉.最大操作压力3巴、最高输出达70kW的带强制通风燃油器的锅炉的特殊要
Heating boilers - Heating boilers with forced
draught burners - Heating boilers with forced
draught burners - Special requirements for boilers
with forced draught oil burners with outputs
up to 70 kW and a maximum operating pressure
of 3 bar - Terminology, special requirements,
testing and marking
BS EN 3079-2006 8°30'压力＜28000kPa的导管接头.适配器.米制系列.技术规范
Pipe coupling 8 °30' up to 28000 kPa - Adaptors
- Metric series - Technical specification
BS EN 3268-2001 航空航天系列.钛合金8°30'管连接件.压力管塞 Aerospace
series - Pipe coupling 8 °30' in titanium alloy
- Pressure plug
BS EN 334-1999 入口压力不大于100bar的气体压力调节器 Gas pressure
regulators for inlet pressures up to 100 bar
BS EN 334-2005 进气口压力不大于100bar的气压调节器 Gas pressure
regulators for inlet pressures up to 100 bar
BS EN 3688-2001 航空航天系列.焊接管用钛合金制T环形填充物.14000kPa公称压力
Aerospace series - T-ring fillers in titanium
alloy for welded pipes - 14000 kPa nominal pressure
BS EN 3689-2001 航空航天系列.焊接管用钛合金制T环形填充物.28000kPa公称压力
Aerospace series - T-ring fillers in titanium
alloy for welding pipes - 28000 kPa nominal
pressure
BS EN 437-2003 试验气体.试验压力.器具分类 Test gases - Test
pressures - Appliance categories
BS EN 464-1994 防护服.对包括气溶液体和固体粒子的液体和气体化学物质的防护.试验方法.气体密封服的密封性测定(内压力试验
Protective clothing - Protection against liquid
and gaseous chemicals, including liquid aerosols
and solid particles - Test method - Determination
of leak-tightness of gas-tight suits (Internal
Pressure Test)
BS EN 472-1995 压力计.词汇 Pressure gauges - Vocabulary
BS EN 50216-5-2002 电力变压器和反应堆配件.液位、压力装置和流量指示计
Power transformer and reactor fittings - Liquid
level, pressure and flow indicators, pressure
relief devices and dehydrating breathers
BS EN 50289-3-15-2003 通信电缆.试验方法规范.机械试验方法.海底电缆耐静水压力
Communication cables - Specifications for test
methods - Mechanical test methods - Underwater
cable resistance to hydrostatic pressure
BS EN 50464-1-2007 最高压力不超过36kV的设备用50Hz、50kVA至2500kVA的三相油浸式配电变压器.一般要求
Three-phase oil-immersed distribution transformers
50 Hz, from 50 kVA to 2500 kVA with highest
voltage for equipment not exceeding 36 kV -
General requirements
BS EN 50464-2-1-2007 最高压力不超过36kV的设备用50Hz、50kVA至2500kVA的三相油浸式配电变压器.高压侧和/或低压侧上带电缆接线盒
Three-phase oil-immersed distribution transformers
50 Hz, from 50 kVA to 2500 kVA with highest
voltage for equipment not exceeding 36 kV -
Distribution transformers with cable boxes on
the high-voltage and/or low-voltage side - General
requirements
BS EN 50464-2-2-2007 最高压力不超过36kV的设备用50Hz、50kVA至2500kVA的三相油浸式配电变压器.高压侧和/或低压侧上带电缆接线盒
Three-phase oil-immersed distribution transformers
50 Hz, from 50 kVA to 2 500 kVA with highest
voltage for equipment not exceeding 36 kV -
Distribution transformers with cable boxes on
the high-voltage and/or low-voltage side - Cable
boxes type 1 for use on distribution transformers
meeting the requirements of EN 50464-2-1
BS EN 50464-2-3-2007 最高压力不超过36kV的设备用50Hz、50kVA至2500kVA的三相油浸式配电变压器.高压侧和/或低压侧上带电缆接线盒
Three-phase oil-immersed distribution transformers
50 Hz, from 50 kVA to 2500 kVA with highest
voltage for equipment not exceeding 36 kV -
Distribution transformers with cable boxes on
the high-voltage and/or low-voltage side - Cable
boxes type 2 for use on distribution transformers
meeting the requirements of EN 50464-2-1
BS EN 50464-3-2007 最高压力不超过36kV的设备用50Hz、50kVA至2500kVA的三相油浸式配电变压器.载有非正弦电流的变压器额定功率
Three-phase oil-immersed distribution transformers
50 Hz, from 50 kVA to 2500 kVA with highest
voltage for equipment not exceeding 36 kV -
Determination of the power rating of a transformer
loaded with non-sinusoidal currents
BS EN 50464-4-2007 最高压力不超过36kV的设备用50Hz、50kVA至2500kVA的三相油浸式配电变压器.关于增压式波形槽的要求和试验
Three-phase oil-immersed distribution transformers
50 Hz, from 50 kVA to 2500 kVA with highest
voltage for equipment not exceeding 36 kV -
Requirements and tests concerning pressurised
corrugated tanks
BS EN 512-1995 纤维水泥制品.压力管道和接头 Fibre-cement products
- Pressure pipes and joints
BS EN 562-2003 气焊设备.焊接、切割和相关工艺用压力计 Gas welding
equipment - Pressure gauges used in welding,
cutting and allied processes
BS EN 60079-2-2004 爆炸性气体环境用电气设备.压力封装型"p"
Electrical apparatus for explosive gas atmospheres
- Pressurized enclosures "p"
BS EN 60811-3-1-1995 电缆的绝缘和护套材料.通用试验方法.聚氯乙烯专用方法.高温下压力试验.耐裂性试验
Insulating and sheathing materials of electric
cables - Common test methods - Methods specific
to PVC compounds - Pressure test at high temperature
- Tests for resistance to cracking
BS EN 61094-2-1994 测量传声器的规范.用互逆性技术对实验室标准传声器进行压力校准的基本方法
Specification for measurement microphones -
Primary method for pressure calibration of laboratory
standard microphones by the reciprocity technique
BS EN 61094-5-2002 测量传声器.用比较片做用工作标准传声器的压力校准方法
Measurement microphones - Methods for pressure
calibration of working standard microphones
by comparison
BS EN 61846-1999 超声波.压力脉冲碎石器.电磁场特性 Ultrasonics
- Pressure pulse lithotripters - Characteristics
of fields
BS EN 639-1995 包括接头和配件的混凝土压力管的共同要求 Common requirements
for concrete pressure pipes including joints
and fittings
BS EN 640-1995 钢筋混凝土压力管和分布钢筋混凝土压力管（非圆柱型），包括接头和配件
Reinforced concrete pressure pipes and distributed
reinforcement concrete pressure pipes (non-cylinder
type), including joints and fittings
BS EN 641-1995 包括接头和配件的圆柱型加筋混凝土压力管 Reinforced
concrete pressure pipes, cylinder type, including
joints and fittings
BS EN 642-1995 包括接头、配件和管道预应力钢特殊要求的圆柱型和非圆柱型预应力混凝土压力管
Prestressed concrete pressure pipes, cylinder
and non-cylinder, including joints, fittings
and specific requirement for prestressing steel
for pipes
BS EN 692-2005 机床.机械压力.安全 Machine tools - Mechanical
presses - Safety
BS EN 712-1995 热塑管道系统.压力管和配件之间端部承载的机械接合.在恒定径向力下抗拔出性能的试验方法
Thermoplastics piping systems - End-load bearing
mechanical joints between pressure pipes and
fittings - Test method for resistance to pull-out
under constant longitudinal force
BS EN 713-1995 塑料管道系统.管件和聚烯烃压力管的机械连接.组件承受弯曲作用时内部压力密封性的试验方法
Plastics piping systems - Mechanical joints
between fittings and polyolefin pressure pipes
- Test method for leaktightness under internal
pressure of assemblies subjected to bending
BS EN 714-1995 热塑管道系统.压力管和模塑管件的无端负荷弹性密封环型连接件.在无轴向推力时内部流体静压力下密封性的试验
Thermoplastics piping systems - Non-end-load-bearing
elastomeric sealing ring type joints between
pressure pipes and moulded fittings - Test method
for leaktightness under internal hydrostatic
pressure without end thrust
BS EN 715-1995 热塑管道系统.小直径压力管和配件间端部负荷轴承接头.在包含端推力的内部水压下密封性的试验方法
Thermoplastics piping systems - End-load-bearing
joints between small diameter pressure pipes
and fittings - Test method for leaktightness
under internal water pressure, including end
thrust
BS EN 738-3-1999 医疗用气体的压力调节器.与气瓶阀组合的压力调节器 Pressure
regulators for use with medical gases - Pressure
regulators integrated with cylinder valves
BS EN 738-4-1999 医疗用气体的压力调节器.医疗设备用低压力调节器 Pressure
regulators for use with medical gases - Low-pressure
regulators intended for incorporation into medical
equipment
BS EN 764-1-2004 压力设备.术语.压力、温度、体积和标称尺寸 Pressure
equipment - Terminology - Pressure, temperature,
volume, nominal size
BS EN 764-2-2002 压力设备.量值、符号和单位 Pressure equipment
- Quantities, symbols and units
BS EN 764-3-2002 压力设备.有关方的定义 Pressure equipment
- Definition of parties involved
BS EN 764-4-2002 压力设备.金属材料的交货技术条件的编制 Pressure
equipment - Establishment of technical delivery
conditions for metallic materials
BS EN 764-5-2002 压力设备.材料的合格性和检验文献 Pressure equipment
- Compliance and inspection documentation of
materials
BS EN 764-7-2002 压力设备.不用火加热的压力容器的安全性系统 Pressure
equipment - Safety systems for unfired pressure
vessels
BS EN 773-1999 液压压力排气管、排水管和污水管道中使用部件的一般要求 General
requirements for components used in hydraulically
pressurized discharge pipes, drains and sewers
BS EN 802-1995 塑料管和管道系统.压力管道系统的注射铸造热塑性部件.最大挤压变形试验方法
Plastics piping and ducting systems - Injection-moulded
thermoplastics fittings for pressure piping
systems - Test method for maximum deformation
by crushing
BS EN 803-1995 塑料管道系统.压力管道的弹性密封圈式连接件用注模制热塑塑料性配件.耐无部端推力的快速内压的试验方法
Plastics piping systems - Injection-moulded
thermoplastics fittings for elastic sealing
ring type joints for pressure piping - Test
method for resistance to a short-term internal
pressure without end thrust
BS EN 804-1995 塑料管道系统.压力管道溶剂胶粘接头的注射模塑承口连接管件.短期内部液压压力的试验方法
Plastics piping systems - Injection-moulded
socket fittings for solvent-cemented joints
for pressure piping - Test method for resistance
to a short-term internal hydrostatic pressure
BS EN 837-1-1998 压力计.波登压力计.规格,计量,要求和试验 Pressure
gauges - Bourdon tube pressure gauges - Dimensions,
metrology, requirements and testing
BS EN 837-2-1998 压力计.压力计的选择和安装推荐规范 Pressure
gauges - Selection and installation recommendations
for pressure gauges
BS EN 837-3-1998 压力计.膜式压力计和膜合式压力计.尺寸、计量、要求和试验
Pressure gauges - Diaphragm and capsule pressure
gauges - Dimensions, metrology, requirements
and testing
BS EN 88-1991 入口压力达200毫巴的燃气器具的压力调节器 Pressure
governors for gas appliances for inlet pressures
up to 200 mbar
BS EN 911-1996 塑料管道系统.热塑塑料压力管道用的弹性密封环型接头和机械接头.外部流体静压条件下防漏密封试验方法
Plastics piping systems - Elastomeric sealing
ring type joints and mechanical joints for thermoplastics
pressure piping - Test method for leaktightness
under external hydrostatic pressure
BS EN 976-1-1997 玻璃增强塑料地下油罐.非压力存储液体石油基燃料的卧式园柱油罐.单壁油罐试验方法和要求
Underground tanks of glass-reinforced plastics
(GRP) - Horizontal cylindrical tanks for the
non-pressure storage of liquid petroleum based
fuels - Requirements and test methods for single
wall tanks
BS EN 976-2-1997 玻璃增强塑料地下油罐.非压力存储液体石油基燃料的卧式园柱油罐.单壁油罐的运输,储存,搬运和安装
Underground tanks of glass-reinforced plastics
(GRP) - Horizontal cylindrical tanks for the
non-pressure storage of liquid petroleum based
fuels - Transport, handling, storage and installation
of single wall tanks
BS EN ISO 10079-3-2000 医疗吸引设备.真空或压力吸引设备 Medical
suction equipment - Suction equipment powered
from a vacuum or pressure source
BS EN ISO 10426-4-2005 石油和天然气工业.油井固井用水泥和材料.在大气压力下泡沫水泥浆的制备和试验
Petroleum and natural gas industries - Cements
and materials for well cementing - Preparation
and testing of foamed cement slurries at atmospheric
pressure
BS EN ISO 10426-5-2006 石油和天然气工业.油井固井用水泥和材料.在大压力下固井水泥加工制剂的收缩和膨胀的测定
Petroleum and natural gas industries - Cements
and materials for well cementing - Determination
of shrinkage and expansion of well cement formulations
at atmospheric pressure
BS EN ISO 10524-1-2006 医用气体设备用的压力调节器和带流量计的压力调节器
Pressure regulators for use with medical gases
- Pressure regulators and pressure regulators
with flow-metering devices
BS EN ISO 10524-2-2007 医用气体的压力调节器.歧管和线管压力调节器
Pressure regulators for use with medical gases
- Manifold and line pressure regulators
BS EN ISO 1167-1-2006 流体传输用热塑管、配件和组件.抗内压力的测定.通用方法
Thermoplastics pipes, fittings and assemblies
for the conveyance of fluids - Determination
of the resistance to internal pressure - General
method
BS EN ISO 1167-2-2006 流体传输用热塑管、配件和组件.抗内压力的测定.管道试件制备
Thermoplastics pipes, fittings and assemblies
for the conveyance of fluids - Determination
of the resistance to internal pressure - Preparation
of pipe test pieces
BS EN ISO 12048-2001 包装.满装运输包装.用压力试验机的压力试验和堆积试验
Packaging - Complete, filled transport packages
- Compression and stacking tests using a compression
tester
BS EN ISO 12162-1996 压力用热塑性塑料管道和管件.分类和设计.总体使用（设计）系数
Thermoplastics materials for pipes and fittings
for pressure applications - Classification and
design - Overall service (design) coefficient
BS EN ISO 13760-2000 流体输送用压力塑料管.Miner规则.累积损坏的计算方法
Plastics pipes for the conveyance of fluids
under pressure - Miner's rule - Calculation
method for cumulative damage
BS EN ISO 13846-2001 塑料管道系统.热塑性压力管用端负载和无端负载支承组件和接头.内部水压下长期密封性的试验方法
Plastics piping systems - End-load-bearing and
non-end-load bearing assemblies and joints for
thermoplastics pressure piping - Test method
for long-term leaktightness under internal water
pressure
BS EN ISO 15265-2004 热环境的人类工效学.热工作条件下防止压力和不适的风险评估政策
Ergonomics of the thermal environment - Risk
assessment strategy for the prevention of stress
or discomfort in thermal working conditions
BS EN ISO 15364-2000 船舶与海上技术.散货船真空/压力阀 Ships
and marine technology - Pressure/vacuum valves
for cargo tanks
BS EN ISO 15616-3-2003 高质量焊接和切割用CO2激光束机的验收试验.气体流量和压力测量仪的校正
Acceptance tests for CO2- laser beam machines
for high quality welding and cutting - Calibration
of instruments for measurement of gas flow and
pressure
BS EN ISO 15996-2005 储气瓶.剩余压力阀.一般要求和型式试验 Gas
cylinders - Residual pressure valves - General
requirements and type testing
BS EN ISO 17654-2003 金属材料焊缝的有损试验.电阻焊接.电阻缝焊的压力试验
Destructive tests on welds in metallic materials
- Resistance welding - Pressure test on resistance
seam welds
BS EN ISO 20623-2004 石油及其产品的试验方法.BS 2000-239:流体的极限压力和耐磨特性测定.四球法(欧洲条件)
Petroleum and related products - Determination
of the extreme-pressure and anti-wear properties
of fluids - Four ball method (European conditions)
BS EN ISO 23251-2006 石油、石化和天然气工业.压力释放和降压系统 Petroleum,
petrochemical and natural gas industries - Pressure-relieving
and depressuring systems
BS EN ISO 2556-2001 塑料.在大气压力下薄膜和薄板的气体透过率的测定.测压法
Plastics - Determination of the gas transmission
rate of films and thin sheets under atmospheric
pressure - Manometric method
BS EN ISO 2811-4-2001 涂料和清漆.密度的测定.压力杯法 Paints
and varnishes - Determination of density - Pressure
cup method
BS EN ISO 3405-2000 石油及其制品的试验方法.石油产品.大气压力下蒸馏特性的测定
Methods of test for petroleum and its products
- Petroleum products - Determination of distillation
characteristics at atmospheric pressure
BS EN ISO 3744-1994 声学.用声压力测定噪声源的声功率级.在声音反射平面上基本自由场中的测量方法
Acoustics - Determination of sound power levels
of noise sources using sound pressure - Engineering
method in an essentially free field over a reflecting
plane
BS EN ISO 3746-1996 声学.用噪声压力测定噪声功率级.在反射平面上利用包封测量表面的测量法
Acoustics - Determination of sound power levels
of noise sources using sound pressure - Survey
method using an enveloping measurement surface
over a reflecting plane
BS EN ISO 3993-1996 液化石油气和轻质烃类.密度或相对密度的测定.压力石油密度计法
Liquefied petroleum gas and light hydrocarbons
- Determination of density or relative density
- Pressure hydrometer method
BS EN ISO 4256-1998 液体石油产品.标准蒸气压力的测定.LPG法 Liquid
petroleum products - Determination of gauge
vapour pressure - LPG method
BS EN ISO 4622-1993 色漆和清漆.堆积压力试验 Paints and
varnishes - Pressure test for stackability
BS EN ISO 6520-2-2002 焊接及相关工艺.金属材料中几何缺陷的分类.压力焊
Welding and allied processes - Classification
of geometric imperfections in metallic materials
- Welding with pressure
BS EN ISO 7291-2001 气焊设备.300bar以下的焊接、切削及相关工艺用汇流系统用压力调节器
Gas welding equipment - Pressure regulators
for manifold systems used in welding, cutting
and allied processes up to 300 bar
BS EN ISO 7458-2004 玻璃容器.耐内压力.试验方法 Glass containers
- Internal pressure resistance - Test methods
BS EN ISO 7751-1997 橡胶和塑料软管和软管组件.试验压力和爆破压力与设计工作压力之比
Rubber and plastics hoses and hose assemblies
- Ratios of proof and burst pressure to design
working pressure
BS EN ISO 8536-10-2004 医用输液设备.与压力输液仪器一起使用的输液管附件
Infusion equipment for medical use - Accessories
for fluid lines for use with pressure infusion
equipment
BS EN ISO 8536-11-2004 医用输液设备.与压力输液仪器一起使用的输液过滤器
Infusion equipment for medical use - Infusion
filters for use with pressure infusion equipment
BS EN ISO 8536-8-2004 医用输液器具.与压力输液仪器一起使用的输液器具
Infusion equipment for medical use - Infusion
equipment for use with pressure infusion apparatus
BS EN ISO 8536-9-2004 医用输液设备.与压力输液仪器一起使用的输液管
Infusion equipment for medical use - Fluid lines
for use with pressure infusion equipment
BS EN ISO 8973-1999 液化石油气.密度和蒸气压力的计算方法 Liquefied
petroleum gases - Calculation method for density
and vapour pressure
BS EN ISO 9311-3-2005 热塑性管道系统用胶粘剂.测定耐内压力性的试验方法
Adhesives for thermoplastic piping systems -
Test method for the determination of resistance
to internal pressure
BS EN ISO 9863-1-2005 土工合成织物.特定压力下厚度的测定.单层 Geosynthetics
- Determination of thickness at specified pressures
- Single layers
BS EN ISO 9863-2-1996 土工织物和相关产品.特定压力下厚度的测定.多层制品的单层厚度测定程序
Geotextiles and geotextile-related products
- Determination of thickness at specified pressures
- Procedure for determination of thickness of
single layers of multilayer products
BS G 226-1979 压力高度计系统伺服型计数器和指示器规范 Specification
for counter and pointer, servo type, pressure
altimeter systems
BS G 240-1988 航空用压力传感器规范 Specification for pressure
transducers for use on aircraft
BS G 259-1996 航空用设备.机载设备环境和操作条件.湿度、温度和压力试验 Aircraft
equipment - Environmental and operating conditions
for airborne equipment - Humidity, temperature
and pressure tests
BS IEC 60747-14-3-2001 分立半导体器件和集成电路.半导体器件.半导体传感器.压力传感器
Discrete semiconductor devices and integrated
circuits - Semiconductor devices - Semiconductor
sensors - Pressure sensors
BS IEC 62117-2000 核反应堆仪表.压力轻水反应堆(PWR).冷停过程中堆芯充分冷却的监测
Nuclear reactor instrumentation - Pressurized
light water reactors (PWR) - Monitoring adequate
cooling within the core during cold shutdown
BS ISO 10767-1-1996 液压流体动力.对系统和部件产生压力波动级的测定.第1部分:泵精度法
Hydraulic fluid power - Determination of pressure
ripple levels generated in systems and components
- Precision method for pumps
BS ISO 10767-2-1999 液压传动.系统和元件中产生压力波动值的测定.泵的简化方法
Hydraulic fluid power - Determination of pressure
ripple levels generated in systems and components
- Simplified method for pumps
BS ISO 10767-3-2000 液压传动.系统和元件产生压力波动值的测定.马达用方法
Hydraulic fluid power - Determination of pressure
ripple levels generated in systems and components
- Method for motors
BS ISO 10771-1-2002 液压流体动力.金属压力容器外壳的疲劳压力试验.试验方法
Hydraulic fluid power - Fatigue pressure testing
of metal pressure-containing envelopes - Test
method
BS ISO 12334-2000 航空航天.液压的压力补偿的变量输送泵.35000KPa系统的一般要求
Aerospace - Hydraulic, pressure-compensated,
variable delivery pumps - General requirements
for 35000 kPa systems
BS ISO 13994-1998 防液体化学制品的防护服装.防护服装材料在压力下防液体渗透的阻力测定
Clothing for protection against liquid chemicals
- Determination of the resistance of protective
clothing materials to penetration by liquids
under pressure
BS ISO 14623-2004 航天系统.压力容器和压力构件.设计和操作 Space
systems - Pressure vessels and pressurized structures
- Design and operation
BS ISO 15081-2005 农业灌溉设备.压力灌溉系统用图形符号 Agricultural
irrigation equipment - Graphical symbols for
pressurized irrigation systems
BS ISO 15171-1-1999 液压和一般用途的连接.诊断用的液压联结器.不用于压力条件下连接的联结器
Connections for fluid power and general use
- Hydraulic couplings for diagnostic purposes
- Coupling not for connection under pressure
BS ISO 15364-2000 船舶技术.货槽用压力/真空阀 Ships and marine
technology. Pressure/vacuum valves for cargo
tanks
BS ISO 15379-1-2004 铝生产用含碳材料.阴极块材料.压力作用下由于钠渗透引起的膨胀的测定
Carbonaceous materials for the production of
aluminium - Cathode block materials - Determination
of the expansion due to sodium penetration with
application of pressure
BS ISO 15379-2-2004 铝生产用碳质材料.阴极块材料.无压力作用下由于钠渗透引起的膨胀的测定
Carbonaceous materials for the production of
aluminium - Cathode block materials - Determination
of the expansion due to sodium penetration without
application of pressure
BS ISO 15734-2003 船舶和海上技术.静水压力释放装置 Ships and
marine technology - Hydrostatic release units
BS ISO 16028-2000 液压流体动力.在20MPa(200巴)到31.5MPa(315巴)的压力下使用平面型速动联轴器.规范
Hydraulic fluid power - Flush-face type, quick-action
couplings for use at pressures of 20 MPa (200
bar) to 31,5 MPa (315 bar) - Specifications
BS ISO 16232-3-2007 道路车辆.液压管路部件清洁度.压力漂洗萃取污染物的方法
Road vehicles - Cleanliness of components of
fluid circuits - Method of extraction of contaminants
by pressure rinsing
BS ISO 16422-2006 压力送水用定向未增塑聚(氯)乙烯(PVC-O)制作的管道和接头.规范
Pipes and joints made of oriented unplasticized
poly(vinyl chloride) (PVC-O) for the conveyance
of water under pressure - Specifications
BS ISO 16873-2002 液压流体动力.压力开关.安装表面 Hydraulic
fluid power - Pressure switches - Mounting surfaces
BS ISO 17484-1-2006 塑料管道系统.最大工作压力达到5bar(500kPa)及以下的室内燃气装置用多层管道系统.系统规范
Plastics piping systems - Multi-layer pipe systems
for indoor gas installations with a maximum
operating pressure up to and including 5 bar
(500 kPa) - Specifications for systems
BS ISO 17744-2004 塑料.作为温度和压力函数的比容的测定(pvT图).活塞装置法
Plastics - Determination of specific volume
as a function of temperature and pressure (pVT
diagram) - Piston apparatus method
BS ISO 18172-1-2007 储气瓶.可再充装的焊接不锈钢气瓶.试验压力≤6MPa
Gas cylinders - Refillable welded stainless
steel cylinders - Test pressure 6 MPa and below
BS ISO 18172-2-2007 储气瓶.可再充装的焊接不锈钢气瓶.试验压力≥6MPa
Gas cylinders - Refillable welded stainless
steel cylinders - Test pressure greater than
6 MPa
BS ISO 18752-2006 橡胶软管和软管组件.金属丝或纺织物.液压设备用的单胎压力加强型.规范
Rubber hoses and hose assemblies - Wire- or
textile-reinforced single pressure types for
hydraulic applications - Specification
BS ISO 19973-4-2007 气压传动.通过测试评定元件的可靠度.压力调节器
Pneumatic fluid power - Assessment of component
reliability by testing - Pressure regulators
BS ISO 21750-2006 道路车辆.有关增进轮胎充气压力监控的安全 Road
vehicles - Safety enhancement in conjunction
with tyre inflation pressure monitoring
BS ISO 2186-2007 封闭管道中的流体流量.一次和二次元件间压力信号传送的连接件
Fluid flow in closed conduits - Connections
for pressure signal transmissions between primary
and secondary elements
BS ISO 23251-2006 石油、石化和天然气工业.释放压力和解压系统 Petroleum,
petrochemical and natural gas industries - Pressure-relieving
and depressuring systems
BS ISO 2944-2000 液压动力系统和元件.标称压力 Fluid power
systems and components - Nominal pressures
BS ISO 3007-2002 石油及其产品试验方法.BS 2000-69: 石油产品.蒸汽压力的测定.瑞利法
Methods of test for petroleum and its products
- BS 2000-69: Petroleum products - Determination
of vapour pressure - Reid method
BS ISO 3322-1996 流体动力系统和部件.液压缸.标称压力 Fluid power
systems and components - Cylinders - Nominal
pressures
BS ISO 4179-2005 压力和非压力管道用球墨铸铁管和配件.水泥灰浆内衬 Ductile
iron pipes and fittings for pressure and non-pressure
pipelines - Cement mortar lining
BS ISO 4250-2-2006 土方机械轮胎和轮辋.载重和充气压力 Earth-mover
tyres and rims - Loads and inflation pressures
BS ISO 5596-2000 液压传动.隔离式充气蓄能器.压力、容积范围和特性量 Hydraulic
fluid power - Gas-loaded accumulators with separator
- Ranges of pressures and volumes and characteristic
quantities
BS ISO 6162-1-2002 液压传动.带对开夹或整体式法兰夹的法兰接头以及公制或英制螺钉.在压力为3,5MPa(35bar)至35MPa(350bar),DN1
Hydraulic fluid power - Flange connectors with
split or one-piece flange clamps and metric
or inch screws - Flange connectors for use at
pressures of 3,5 MPa (35 bar) to 35 MPa (350
bar), DN 13 to DN 127
BS ISO 6162-2-2002 液压传动.带对开夹或整体式法兰夹的法兰接头以及公制或英制螺钉.在压力为35MPa(350bar)至40MPa(400bar),DN1
Hydraulic fluid power - Flange connectors with
split or one-piece flange clamps and metric
or inch screws - Flange connectors for use at
pressures of 35 MPa (350 bar) to 40 MPa (400
bar), DN 13 to DN 51
BS ISO 6771-2007 航空航天.流体系统和部件.压力和温度分类 Aerospace
- Fluid systems and components - Pressure and
temperature classifications
BS ISO 7169-2007 航空航天.液压系统用24°锥形的、压力范围截至3000psi或21000kPa的可拆卸管接头.采购规范(英制/米制)
Aerospace - Separable tube fittings for fluid
systems, for 24 ° cones, for pressures up to
3000 psi or 21000 kPa - Procurement specification,
inch/metric
BS ISO 727-2-2005 压力管件用由未增塑聚氯乙烯(PVC-U)、氯化聚氯乙烯(PVC-C)或丙烯腈/丁二烯/苯乙烯(ABS)制的带普通管套的管
Fittings made from unplasticized poly(vinyl
chloride) (PVC-U), chlorinated poly(vinyl chloride)
(PVC-C) or acrylonitrile/butadiene/styrene (ABS)
with plain sockets for pipes under pressure
- Inch-based series
BS ISO 9022-18-1995 光学和光学仪器.环境试验方法.混合式湿热压力和低内压力
Optics and optical instruments - Environmental
test methods - Combined damp heat and low internal
pressure
BS ISO 9393-1-2004 工业用热塑性阀门.压力试验方法和要求.总则 Thermoplastics
valves for industrial applications - Pressure
test methods and requirements - General
BS ISO 9831-1998 动物饲料、动物制品和粪便或尿液.总热量值测定.压力热量计法
Animal feeding stuffs, animal products, and
faeces or urine - Determination of gross calorific
value - Bomb calorimeter method
BS M 65-1987 压力补偿变量液压泵规范 Specification for pressure
compensated variable delivery hydraulic pumps
CP 312-2-1973 塑料管道(热塑材料)实用规程.第2部分:压力液体输送用非增塑PVC管
Code of practice for plastics pipework (thermoplastics
material). Unplasticized PVC pipework for the
conveyance of liquids under pressure
DD ENV 12108-2001 塑料管道系统.建筑物内部的人用冷热水压力管道系统的安装指南
Plastics piping systems. Guidance for the installation
inside buildings of pressure systems for hot
and cold water intended for human consumption
DD ENV 12291-1996 高技术陶瓷.大气压力高温下陶瓷复合材料的机械性能.压缩性能的测定
Advanced technical ceramics. Mechanical properties
of ceramic composites at high temperature in
air at atmospheric pressure. Determination of
compression properties
DD ENV 12789-1998 高技术陶瓷.大气压力高温情况下陶瓷复合物机械性能.挠性强度测定
Advanced technical ceramics. Mechanical properties
of ceramic composites at high temperature under
air at atmospheric pressure. Determination of
flexural strength
DD ENV 1401-2-2001 非压力地下废水排放和污水系统的塑料管道系统.非增塑聚氯乙烯.符合性评定指南
Plastics piping systems for non-pressure underground
drainage and sewerage. Unplasticized poly(vinylchloride)
(PVC-U). Guidance for assessment of conformity
DD ENV 1401-3-2001 非压力地下废水和排水系统的塑料管道系统.非增塑聚氯乙烯（PVC－U）.安装指南
Plastics piping systems for non-pressure underground
drainage and sewerage. Unplasticized poly(vinylchloride)
(PVC-U). Guidance for installation
DD ENV 1852-2-2001 非压力地下废水排放和污水系统的塑料管道系统.聚丙烯.符合性评定指南
Plastics piping systems for non-pressure underground
drainage and sewerage. Polypropylene (PP). Guidance
for the assessment of conformity
DD ENV 1893-1996 高技术陶瓷.在大气压力而又高温情况下陶瓷成分的机械性能.抗拉性能测定
Advanced technical ceramics. Mechanical properties
of ceramic composites at high temperature in
air at atmospheric pressure. Determination of
tensile properties
DD ENV 22605-1-1992 压力用钢制品.温升参数的导出和证明.第1部分:碳和低合金钢制品的屈服或试验应力
Steel products for pressure purposes. Derivation
and verification of elevated temperature properties.
Yield or proof stress of carbon and low alloy
steel products
DD ENV 22605-2-1992 压力用钢制品.温升特性的导出和证明.第2部分:奥氏体钢制品的试验应力
Steel products for pressure purposes. Derivation
and verification of elevated temperature properties.
Proof stress of austenitic steel products
DD ENV 22605-3-1992 压力用钢制品.温升特性的导出和证明.第3部分:当数据给定时导出温升屈服或试验应力特性的选择程序
Steel products for pressure purposes. Derivation
and verification of elevated temperature properties.
An alternative procedure for deriving the elevated
temperature yield or proof stress properties
when data are limited
KIT 111-2002 非燃烧的压力容器装置 Unfired pressure vessels
kit
PD 6525-1-1990 压力用钢的高温性能.第1部分:应力断裂性能 Elevated
temperature properties for steels for pressure
purposes. Stress rupture properties
TH 20344-2000 锅炉和压力容器.设计和批准要求的国际检验报告 Boilers
and Pressure Vessels - An international survey
of design and approval requirements
TH 42069-2000 压力容器.德国 Pressure Vessels: Germany
中国压力标准(GB pressure standards)
--------------------------------------------------------------------------------
编号 中文名称 英文名称
DL 612-1996(2005) 电力工业锅炉压力容器监察规程 ()
DL 647-2004 电站锅炉压力容器检验规程 ()
DL/T 1045-2007 钢弦式孔隙水压力计 vibrating wire piezometers
DL/T 5017-2007 水电水利工程压力钢管制造安装及验收规范 Specifications
for manufacture installation and acceptance
of steel penstocks in hydroelectric and hydraulic
engineering
DL/T 5141-2001 水电站压力钢管设计规范 ()
DL/T 709-1999 压力钢管安全检测技术规程 ()
DL/T 874-2004 电力工业锅炉压力容器安全监督管理(检验)工程师资格考核规则
()
FZ 90058-1994 压力容器类产品图样标注的规定 ()
FZ/T 90097-1998 染整机械轧车线压力 ()
FZ/T 99097-1998 染整机械轧车线压力 ()
GB 13623-2003 铝压力锅安全及性能要求 Requirement of safety
and characterstics of aluminium pressure cooker
GB 14536.7-1996 家用和类似用途电自动控制器压力敏感电自动控制器的特殊要求(包括机械要求)
Automatic electrical controls for household
and similar use--Particular requirements for
automatic electrical pressure sensing controls
including mechanicalrequirements
GB 150-1998 钢制压力容器 Steel pressure vessels
GB 15066-2004 不锈钢压力锅 Stainless steel pressure
cooker
GB 16749-1997 压力容器波形膨胀节 Bellows expansion joints
for pressure vessel
GB 18442-2001 低温绝热压力容器 Cryo-insulation pressure
vessels
GB 19189-2003 压力容器用调质高强度钢板 Quenched and tempered
high strength steel plates for pressure vessels
GB 19521.14-2004 危险货物中小型压力容器检验安全规范 Safety code
for the inspection of medium and minitype receptacles
for dangerous goods
GB 20580-2006 化学品分类、警示标签和警示性说明安全规范 压力下气体 Safety
rules for classification、precautionary labelling
and precautionary statements of chemicals -
Gases under pressure
GB 3531-1996 低温压力容器用低合金钢钢板 Low alloy steel plates
for low temperature pressure vessels
GB 4584-2007 压力机用光电保护装置技术条件 Specification of
active opto-electronic protective devices for
presses
GB 4793.8-2008 测量、控制和试验室用电气设备的安全要求 第2-42部分：使用有毒气体处理医用材料及供试验室用的压力灭菌器
()
GB 5091-1985 压力机的安全装置技术要求 Technical requirememts
for safety devices of the presses
GB 5092-1985 压力机用感应式安全装置技术条件 Technical requirements
for induction type safety device used for the
presses
GB 5093-1985 压力机用手持电磁吸盘技术条件 Technical requirements
for hand-held electromagnetic disk used for
the presses
GB 5135.10-2006 自动喷水灭火系统 第10部分:压力开关 Automatic
sprinkler system-Part10:Pressure switch
GB 713-2008 锅炉和压力容器用钢板 ()
GB 8599-1988 自动控制压力蒸汽灭菌器技术条件 Specifications
for automated autoclave sterilizer
GB 9326.5-1988 交流330 kV 及以下油纸绝缘自容式充油电缆及附件压力供油箱
Oil-filled paper-insulated cables and accessories
for alternating voltages up to and inclnding
330kV--Pressure tanks
GB/T 1048-2005 管道元件--PN(公称压力)的定义和选用 Pipework
components-Definition and selection of PN
GB/T 10924-1989 闭式单点压力机精度 Straight sided one-point
mechanical presses--Testing of the accuracy
GB/T 10933-1989 闭式双点压力机精度 Straight sided two-point
mechanical presses--Testing of the accuracy
GB/T 11191-2004 航空轮胎爆破压力试验方法 Test method of
burst pressure for aircraft tyre
GB/T 11195-1998 航空有内胎轮胎胎圈密合压力试验方法 Bead fit test
method for tube aircraft tyre
GB/T 11828.2-2005 水位测量仪器第2部分:压力式水位计 Instruments
for Stage Measurement-Part 2:Pressure-Type Stage
Guage
GB/T 12242-2005 压力释放装置性能试验规范 Performance Test
Code-Pressure Relief Devices
GB/T 1226-2001 一般压力表 General pressure gauge
GB/T 1227-2002 精密压力表 Accurate pressure gauge
GB/T 13877.5-2003 农林拖拉机和自走式机械封闭驾驶室第5部分: 空气压力调节系统试验方法
Tractors and self-propelled machines for agriculture
and forestry--Operator enclosure environment--Part
5: Pressurization system test method
GB/T 13927-1992 通用阀门压力试验 Pressure testing for
general purpose valves
GB/T 14070-1993 气体分析校准用混合气体的制备压力法 Gas analysis--Preparation
of calibration gas mixtures--Manometric method
GB/T 14347-1993 开式压力机型式与基本参数 Open front mechanical
power presses--Types and basic parameters
GB/T 15443-1995 压水堆压力容器选材原则与基本要求 Pressurized
water reactor pressure vessel--The principle
of selecting materials and the basic requirements
of the materials
GB/T 15478-1995 压力传感器性能试验方法 Test methods of
the performances for pressuretransducer/sensor
GB/T 15820-1995 聚乙烯压力管材与管件连接的耐拉拔试验 Test of resistance
to pull out ofjoints between polyethylene (PE)
pressure pipes and fittings
GB/T 16407-2006 声学医用体外压力脉冲碎石机的声场特性和测量 Acoustics―Characteristics
and measurements of field of Pressurepulse lithotripters
GB/T 16426-1996 粉尘云最大爆炸压力和最大压力上升速率测定方法 Determination
for maximumexplosion pressure and maximum rate
of pressure rise of dust cloud
GB/T 16805-1997 液体石油管道压力试验 Pressure testing
of liquid petroleum pipelines
GB/T 16825.1-2002 静力单轴试验机的检验第1部分:拉力和(或)压力试验机测力系统的检验与校准
Verification of static uniaxial testing machines--Part
1:Tension/compression testing machines--Verification
and calibration of the force-measuring system
GB/T 17200-1997 橡胶塑料拉力、压力、弯曲试验机技术要求 Requirements
for tensile，flexural and compression testing
machines for rubbers and plastics
GB/T 17782-1999 硫化橡胶压力空气热老化试验方法 Rubber，vulcanized--Test
method of aging by heat and air pressure
GB/T 18182-2000 金属压力容器声发射检测及结果评价方法 Acoustic
emission examination andevaluation of metallic
pressure vessels
GB/T 18443.1-2001 低温绝热压力容器试验方法容积测量 Testing method
of cryo-insulation pressure vessels--Volume
measurement
GB/T 18443.2-2001 低温绝热压力容器试验方法真空度测量 Testing
method of cryo-insulation pressure vessels--Vacuum
measurement
GB/T 18443.3-2001 低温绝热压力容器试验方法漏率测量 Testing method
of cryo-insulation pressure vessels--Leakage
measurement
GB/T 18443.4-2001 低温绝热压力容器试验方法漏放气速率测量 Testing
method of cryo-insulation pressure vessels--Leak
and outgassing rate measurement
GB/T 18443.5-2001 低温绝热压力容器试验方法静态蒸发率测量 Testing
method of cryo-insulation pressure vessels--Static
vaporation rate measurement
GB/T 18475-2001 热塑性塑料压力管材和管件用材料分级和命名总体使用(设计)系数
Thermoplastics materials for pipes and fittings
for pressure applications classification and
designation--Overall service(design) coefficient
GB/T 18520-2001 植物保护机械喷雾机喷头和压力表的连接尺寸 Equipment
for crop protection--Sprayers--Connecting dimensions
for nozzles and manometers
GB/T 18688-2002 农业灌溉设备灌溉阀的压力损失试验方法 Agricultural
irrigation equipment--Pressure losses in irrigation
valves--Test method
GB/T 18692-2002 农业灌溉设备直动式压力调节器 Agricultural
irrigation equipment--Direct-acting pressure
regulators
GB/T 18806-2002 电阻应变式压力传感器总规范 General specification
for the resistance strain pressure transducer/sensor
GB/T 18945-2003 高聚物多孔弹性材料恒定压力降时流量的估算方法 Polymeric
materials，cellular flexible--Method of assessment
of air flow value at constant pressure-drop
GB/T 18997.1-2003 铝塑复合压力管第1部分:铝管搭接焊式铝塑管 Polyethylene/Aluminum/Polyethylene
composite pressure pipe--Part 1:PE/AL/PE pipe
overlap-welded by aluminum pipe
GB/T 18997.2-2003 铝塑复合压力管第2部分:铝管对接焊式铝塑管 Polyethylene/Aluminum/Polyethylene
composite pressure pipe--Part 2:PE/AL/PE pipe
butt-welded by aluminum pipe
GB/T 19624-2004 在用含缺陷压力容器安全评定 Safety assessment
for in-service pressure vessels containing defects
GB/T 19699-2005 船舶与海上技术货油舱压力/真空阀 Ships and marine
technology-Pressure/vacuum valves for cargo
tanks
GB/T 19812.2-2005 塑料节水灌溉器材压力补偿式滴头及滴灌管 Plastic
equipment for water saving irrigation-Pressure
compensating emitter and emitting pipe
GB/T 19934.1-2005 液压传动金属承压壳体的疲劳压力试验第1部分：试验方法
Hydraulic fluid power-Fatigue pressure testing
of metal pressure-containing envelopes-Part
1:Test method
GB/T 19955.2-2005 蒸汽流真空泵性能测量方法第2部分：临界前级压力的测量
Vapour vacuum pumps-Measurement of performance
characteristics Part2:Measurement of critical
backing pressure
GB/T 19956.2-2005 容积真空泵性能测量方法第2部分：极限压力的测量 Positive-displacement
cacuum pumps-Measurement of performance characteristics
Part2:Measurement of ultimate pressure
GB/T 20201-2006 灌溉用聚乙烯(PE)压力管机械连接管件 Mechanical
joint fittings for use with polyethylene pressure
pipes for irrigation purposes
GB/T 20207.1-2006 丙烯腈－丁二烯－苯乙烯（ABS）压力管道系统第1部分：管材
Acrylonitrile-butadiene-styrene (ABS) pressure
piping systems - Part 1: Pipes
GB/T 20207.2-2006 丙烯腈－丁二烯－苯乙烯（ABS）压力管道系统第2部分：管件
Acrylonitrile-butadiene-styrene (ABS) pressure
piping systems - Part 2: fittings
GB/T 20421.1-2006 液压马达特性的测定第1部分：在恒低速和恒压力下 Hydraulic
fluid power―Determination of characteristics
of motors―Part 1: At constant low speed and
at constant pressure
GB/T 20522-2006 半导体器件第14-3部分: 半导体传感器-压力传感器 Semiconductor
devices Part 14-3: Semiconductor sensors - Pressure
sensors
GB/T 20663-2006 囊式蓄能用压力容器 Bladder type accumulators
GB/T 20801.1-2006 压力管道规范 工业管道 第1部分:总则 Pressure
piping code Industrial piping―Part 1：General
GB/T 20801.2-2006 压力管道规范 工业管道 第2部分：材料 pressure
piping code - Industrial piping - Part 2: Materials
GB/T 20801.3-2006 压力管道规范 工业管道 第3部分：设计和计算 Pressure
piping code - Industrial piping - Part 3: Design
and calculation
GB/T 20801.4-2006 压力管道规范 工业管道 第4部分：制作与安装 Pressure
piping code - Industrial piping - Part 4: Fabrication
and assembly
GB/T 20801.5-2006 压力管道规范 工业管道 第5部分：检验与试验 Pressure
piping code - Industrial piping - Part 5: Inspection
and testing
GB/T 20801.6-2006 压力管道规范 工业管道 第6部分：安全防护 Pressure
piping code - Industrial piping - Part 6: Safeguarding
GB/T 20910-2007 热水系统用温度压力安全阀 Temperature/pressure
safety valve for hot water supply system
GB/T 21190-2007 纸、纸板和瓦楞纸板 压力试验仪的描述与校准 Paper,
board and corrugated fibreboard - Description
and calibration of compression-testing equipment
GB/T 21432-2008 石墨制压力容器 ()
GB/T 21433-2008 不锈钢压力容器晶间腐蚀敏感性检验 ()
GB/T 21579-2008 危险品 时间/压力试验方法 ()
GB/T 21596-2008 危险品 便携式罐体压力试验方法 ()
GB/T 21616-2008 危险品 易燃液体蒸汽压力试验方法 ()
GB/T 21681-2008 数控压力机、液压机用模拟负荷测试系统 ()
GB/T 2346-2003 流体传动系统及元件公称压力系列 Fluid power systems
and components--Nominal pressures
GB/T 2352-2003 液压传动隔离式充气蓄能器压力和容积范围及特征量 Hydraulic
fluid power--Gas-loaded accumulators with separator--Ranges
of pressures and volumes and characteristic
quantities
GB/T 2951.6-1997 电缆绝缘和护套材料通用试验方法第3部分:聚氯乙烯混合料专用试验方法第1节:高温压力试验----抗开裂试验
Common test methods for insulating and sheathing
materials of electric cables--Part 3:Methods
specific to PVC compounds--Section one:Pressure
test at high temperature--Test for resistance
to cracking
GB/T 3411-1994 差动电阻式孔隙压力计 Unbonded elastic wire
resistance type pore pressure cell
GB/T 3478.2-1995 圆柱直齿渐开线花键30°压力角尺寸表 Straight
cylindrical involute splines--30° pressure angle
dimensions tables
GB/T 3478.3-1995 圆柱直齿渐开线花键37.5°压力角尺寸表 Straight
cylindrical involutesplines--37.5° pressure
angle dimensions tables
GB/T 3478.4-1995 圆柱直齿渐开线花键45°压力角尺寸表 Straight
cylindrical involute splines--45° pressure angle
dimensions tables
GB/T 3478.6-1995 圆柱直齿渐开线花键30°压力角M值和W值 Straight
cylindrical involute splines--30°pressurengle
M and W values
GB/T 3478.7-1995 圆柱直齿渐开线花键37.5°压力角M值和W值 Straight
cylindrical involute splines--37.5°pressure
angle M and W values
GB/T 3478.8-1995 圆柱直齿渐开线花键45°压力角M值和W值 Straight
cylindrical involute splines--45°pressure angle
M and W values
GB/T 3722-1992 液压式压力试验机 Hydraulic compression
testing machines
GB/T 3751-2008 卡套式压力表管接头 ()
GB/T 392-1977 润滑脂压力分油测定法 Determination of colloid-stability
of lubricating greases
GB/T 4217-2001 流体输送用热塑性塑料管材公称外径和公称压力 Thermoplastics
pipes for the conveyance of fluids--Nominal
outside diameters and nominal pressures
GB/T 4546-1998 玻璃瓶罐耐内压力试验方法 Glass containers--Internal
pressure resistance--Method of test
GB/T 4830-1984 工业自动化仪表气源压力范围和质量 Pressure range
and quality of air supply for the industrial
process measurement and control instruments
GB/T 4857.4-2008 包装 运输包装件基本试验 第4部分：采用压力试验机进行的抗压和堆码试验方法
Packaging - Basic tests for transport packages
- Part 4：Compression and Stacking tests using
a compression tester
GB/T 4974-2005 空压机、凿岩机械与气动工具优先压力 Compressors,rock
drilling machines and pneumatic tools-Preferred
pressures
GB/T 5104-2004 30°压力角渐开线花键滚刀基本型式和尺寸 The basic
types and dimensions of hobs for 30°pressure
angle involute splines
GB/T 5105-2004 45°压力角渐开线花键滚刀基本型式和尺寸 The basic
types and dimensions of hobs for 45°pressure
angle involute splines
GB/T 5351-2005 纤维增强热固性塑料管短时水压失效压力试验方法 Fiber-reinforced
thermosetting plastic composites pipe-Determination
of short-time hydraulic failure pressure
GB/T 5645-2008 扩口式压力表管接头 ()
GB/T 5922-1986 汽车和挂车气压制动装置压力测试连接器 Motor vehicles
and towed vehicles--Pressure test connection
for compressed-air pneumatic braking equipment
GB/T 6058-2005 纤维缠绕压力容器制备和内压试验方法 Test method
for preparation and internal pressure testing
of filament-wound pressure vessels
GB/T 6417.2-2005 金属压力焊接头缺欠分类及说明 Classification
and explanation of imperfections in pressure
welded joints
GB/T 7937-2008 液压气动管接头及其相关元件 公称压力系列 ()
GB/T 8105-1987 压力控制阀试验方法 Hydraulic fluid power--Valves--Testing
method of pressure control valves
GB/T 8600-1988 压力蒸汽灭菌器灭菌效果检验方法 Inspecting method
for sterilizing effect of automated autoclave
sterilizer
GB/T 8650-2006 管线钢和压力容器钢抗氢致开裂评定方法 Evaluation
of pipeline and pressure vessel steels for resistance
to hydrogen-induced cracking
GB/T 8892-2005 压力表用铜合金管 Copper alloy tube for
pressure gauge
GB/T 9019-2001 压力容器公称直径 Nominal diameter of
pressure vessels
GB/T 9574-2001 橡胶和塑料软管及软管组合件试验压力、爆破压力与设计工作压力的比率
Rubber and plastics hoses and hose assemblies--Ratios
of proof and burst pressure to design working
pressure
HG 20585-1998 钢制低温压力容器技术规定 ()
HG 20604-1997 钢制管法兰压力——温度等级（欧洲体系） ()
HG 20625-1997 钢制管法兰压力—温度等级（美洲体系） ()
HG 20660-2000 压力容器中化学介质毒性危害和爆炸危险程度分类 ()
HG/T 2353.6-1992 磁浆过滤用滤芯 冒泡压力试验方法 ()
HG/T 2741-1995 压力容器用碳钢铸件技术条件 ()
HG/T 2806-1987 奥氏体不锈钢压力容器制造管理通则 ()
HG/T 3237-2006 橡胶机械用自力式压力调节阀 Self-operated pressure
regulators for rubber machinery
JB 3350-1993 机械压力机 安全技术要求 ()
JB 4708-2000 钢制压力容器焊接工艺评定 ()
JB 4726-2000 压力容器用碳素钢和低合金钢锻件 ()
JB 4727-2000 低温压力容器用碳素钢和低合金钢锻件 ()
JB 4728-2000 压力容器用不锈钢锻件 ()
JB 4733-1996 压力容器用爆炸不锈钢复合钢板 ()
JB 4741-2000 压力容器用镊铜合金热轧板材 ()
JB 4742-2000 压力容器用镍铜合金无缝管 ()
JB 4743-2000 压力容器用镍铜合金锻件 ()
JB 4744-2000 钢制压力容器产品焊接试板的力学性能检验 ()
JB 8780-1998 螺旋压力机 安全技术要求 ()
JB 8897-1999 弹性式压力仪表通用安全规范 ()
JB 9968-1999 开式压力机 噪声限值 ()
JB 9974-1999 闭式压力机 噪声限值 ()
JB 9977-1999 双盘摩擦压力 机噪声限值 ()
JB/T 10168-2000 闭式高速精密压力机 技术条件 ()
JB/T 10203-2000 远传压力表 ()
JB/T 10372-2002 液压压力继电器 ()
JB/T 10385-2002 家用和类似用途手动复位压力式热切断器 ()
JB/T 10524-2005 硅压阻式压力传感器 ()
JB/T 10726-2007 扩散硅式压力变送器 Silicon-diffused pressure
transmitters
JB/T 10782.2-2007 闭式双动拉伸多连杆压力机 第2部分：精度 Straight-side
double-action multi-link-Part 2:Testing of the
accuracy
JB/T 10783.2-2007 闭式四点多连杆压力机 第2部分：精度 Straight-side
four point multi-link-Part 2:Testing of the
accuracy
JB/T 10784-2007 机械式干粉压力机 通用技术条件 General specifications
for mechanical dry powder compacting presses
JB/T 1149-1980 扁平钢带压力容器 技术条件 ()
JB/T 1647-1999 闭式单、双点压力机 型式与基本参数 ()
JB/T 1769-1999 闭式单、双点切边压力机 型式与基本参数 ()
JB/T 2001.22-1999 水系统 压力表开关 型式与尺寸(PN=31.5MPa)
()
JB/T 2474-1999 液压螺旋压力机 基本参数 ()
JB/T 2547.1-2007 双盘摩擦压力机 第1部分：技术条件 Friction
screw presses-Part 1:Specifications
JB/T 2936.1-1999 闭式冷挤压压力机 型式与基本参数 ()
JB/T 2936.2-1999 闭式冷挤压压力机 技术条件 ()
JB/T 3228-1999 闭式机械压力机 紧固模具用槽、打(顶)杆孔的分布形式与尺寸
()
JB/T 3847-1999 开式压力机 紧固模具用槽、孔的分布形式与尺寸 ()
JB/T 3848-1999 闭式多工位压力机 精度 ()
JB/T 3880-1985 底传动双动拉伸压力机 技术条件 ()
JB/T 3881-1999 闭式双动拉伸压力机 精度 ()
JB/T 4700-2000 压力容器法兰分类与技术条件 ()
JB/T 4709-2000 钢制压力容器焊接规程 ()
JB/T 4711-2003 压力容器涂敷与运输包装 ()
JB/T 4732-1995(2005) 钢制压力容器?分析设计标准 ()
JB/T 4746-2002 钢制压力容器用封头 ()
JB/T 4747-2002 压力容器用钢焊条订货技术条件 ()
JB/T 4748-2002 压力容器用镍及镍基合金爆炸复合钢板 ()
JB/T 4750-2003 制冷装置用压力容器 ()
JB/T 50040-1999 弹性式压力表 可靠性技术要求与考核方法 ()
JB/T 5110.1-1991 螺旋压力机锻模 圆形模块结构与尺寸 ()
JB/T 5110.2-1991 螺旋压力机锻模 矩形模块结构与尺寸 ()
JB/T 5110.3-1991 螺旋压力机锻模 模块技术条件 ()
JB/T 5110.4-1992 螺旋压力机锻模 圆形模块用模座 ()
JB/T 5110.5-1992 螺旋压力机锻模 矩形模块用模座 ()
JB/T 5110.6-1992 螺旋压力机锻模 横座技术条件 ()
JB/T 5110.7-1992 螺旋压力机锻模 压圈 ()
JB/T 5198-2007 模锻螺旋压力机 精度 Die-forging screw
presses-Testing of the accuracy
JB/T 5199-1991 开式双点压力机 精度 ()
JB/T 5200-1991 闭式四点压力机 精度 ()
JB/T 5247.1-1998 台式压力机 技术条件 ()
JB/T 5247.2-1998 台式压力机 型式与基本参数 ()
JB/T 5247.3-1999 台式压力机 精度 ()
JB/T 53050-1992 钢制焊接单层压力容器 产品质量分等 ()
JB/T 53051-1992 钢制多层包扎压力容器 产品质量分等 ()
JB/T 53052-1992 热套压力容器 产品质量分等 ()
JB/T 53182-1994 扁平钢带压力容器 质量分等 ()
JB/T 5425-2004 真空压力复合气泵 ()
JB/T 54364-1998 开式压力机 可靠性评定方法 ()
JB/T 54366-1994 闭式压力机可靠性考核评定规范 ()
JB/T 5491-2005 膜片压力表 ()
JB/T 5492-1991 电位器式压力传感器 ()
JB/T 5493-1991 电阻应变式压力传感器 ()
JB/T 5527-2005 船用压力表 ()
JB/T 5528-2005 压力表标度及分划 ()
JB/T 5534-2007 压力式温度控制器用锡青铜波纹管 Tin bronze bellows
for pressure temperature controller
JB/T 5537-2006 半导体压力传感器 Semiconductor pressure
sensors
JB/T 5924-1991 液压元件压力容腔体的额定疲劳压力和额定静态压力验证方法 ()
JB/T 599-2005 压力表校验器 ()
JB/T 5992.3-1992 机械制造工艺方法分类与代码 压力加工 ()
JB/T 6059.1-1992 机械压力机锻模 导柱 ()
JB/T 6059.2-1992 机械压力机锻模 组合态导套外壳 ()
JB/T 6059.3-1992 机械压力机锻模 组合导套衬套 ()
JB/T 6059.4-1992 机械压力机锻模 组合导套刮圈 ()
JB/T 6059.5-1992 机械压力机锻模 导套盖板 ()
JB/T 6059.6-1992 机械压力机锻模 整体导套 ()
JB/T 6059.7-1992 机械压力机锻模 导套油封圈 ()
JB/T 6059.8-1992 机械压力机锻模 定位销 ()
JB/T 6059.9-1992 机械压力机锻模 定位键 ()
JB/T 6170-2006 压力传感器 Pressure sensors
JB/T 6172-2005 压力传感器 系列型谱 ()
JB/T 6385-2007 锥密封焊接式压力表管接头 ()
JB/T 6488.4-1995 云母带 真空压力浸渍用环氧玻璃粉云母带 ()
JB/T 6490-1992 塑料压力成型机 ()
JB/T 6499.1-1992 机械压力机切边模 导柱 ()
JB/T 6499.2-1992 机械压力机切边模 导套 ()
JB/T 6539-1992(2005) 微型空气压缩机用钢制压力容器 ()
JB/T 6580-1993 开式压力机 精度 ()
JB/T 6580.1-1999 开式压力机 技术条件 ()
JB/T 6580.2-1999 开式压力机 性能要求与试验方法 ()
JB/T 6630-1993 机械密封系统用压力罐 型式、主要尺寸和基本参数 ()
JB/T 6801-1993 压力表阻尼器 技术条件 ()
JB/T 6802-2008 压力控制器 Pressure controller
JB/T 6803.1-1993 液体压力计 一般杯形、U 形压力计 ()
JB/T 6803.2-1993 液体压力计 精密杯形、U 形压力计 ()
JB/T 6804-2006 抗震压力表 Shock-resistant pressure
gauge
JB/T 6805-2008 压力表接点装置 技术条件 Technical conditions
for contact devices of pressure gauges
JB/T 6962.1-1993 机械压力机锻模 模座 ()
JB/T 6962.2-1993 机械压力机锻模 垫板 ()
JB/T 6962.3-1993 机械压力机锻模 模块 ()
JB/T 7046-2006 液压蓄能器压力容腔体的额定疲劳压力和额定静态压力验证方法
Hydraulic fluid power-Accumulators-Verify methods
of rated fatigue pressure and rated static pressure
of pressure-containing envelopes
JB/T 7065-2004 变压器用压力释放阀 ()
JB/T 7069-2004 变压器用压力释放阀 试验导则 ()
JB/T 7392-2006 数字压力表 Digital pressure instrument
JB/T 7393-1994 活塞式压力计 ()
JB/T 7482-2008 压电式压力传感器 ()
JB/T 7487.2-2007 金属膜盒 第2部分：金属压力膜盒 Metal capsule-Part
2:Metal pressure capsule
JB/T 7667-1995 在役压力容器声发射检测评定方法 ()
JB/T 7696.1-1995 工程机械用压力表 ()
JB/T 7862.3-2001 农业机械 切割器的压力器 ()
JB/T 7961-1995 制冷用压力、压差控制器 ()
JB/T 8214.7-1999 QDZ气动单元组合仪表 压力变送器 ()
JB/T 8216.5-1999 DDZ-Ⅱ系列电动单元组合仪表 力平衡式压力变送器 ()
JB/T 8217.2-1999 B系列气动基地式仪表 压力仪表 ()
JB/T 8347-1996 开式压力机 操作指示形象符号 ()
JB/T 8348.1-1996 底传动双动拉伸压力机 精度 ()
JB/T 8348.2-1996 底传动双动拉伸压力机 技术条件 ()
JB/T 8472.2-1996 蒸汽流真空泵性能测定 第二部分:临界前级压力的测定 ()
JB/T 8597-1997 钢筋电渣压力焊机技术条件 ()
JB/T 8624-1997 隔膜式压力表 ()
JB/T 8763-2001 电液式水泥压力试验机 技术条件 ()
JB/T 8782-1998 闭式高速精密压力机 精度 ()
JB/T 8839.1-1999 内燃机用磁电式压力表 技术条件 ()
JB/T 8839.2-1999 内燃机用磁电式压力表 试验方法 ()
JB/T 8843.1-1999 内燃机用压力报警器 技术条件 ()
JB/T 8843.2-1999 内燃机用压力报警器 试验方法 ()
JB/T 8904.2-1999 KF系列气动基地式仪表KFK型压力指示调节仪 ()
JB/T 8904.5-1999 KF系列气动基地式仪表KFP型压力指示调节仪 ()
JB/T 8967-1999 家用和类似用途压力式温度控制器 ()
JB/T 9235-1999 工业自动化仪表 公称工作压力值系列 ()
JB/T 9259-1999 蒸汽和气体压力式温度计 ()
JB/T 9271-1999 焊接、切割及类似工艺用压力表 ()
JB/T 9272-1999 氨压力表 ()
JB/T 9273-1999 电接点压力表 ()
JB/T 9274-1999 膜盒压力表 ()
JB/T 9275-1999 电接点膜盒压力表 ()
JB/T 9277-1999 压力表误差表 ()
JB/T 9278-1999 压力表齿轮传动机构 技术条件 ()
JB/T 9448-1999 静电复印机用硅橡胶定影压力辊 技术条件 ()
JB/T 9451-1999 大气压力传感器 试验导则 ()
JB/T 9842-1999 拖拉机、内燃机用弹簧管式压力表 ()
JB/T 9961-1999 开式多工位压力机 精度 ()
JB/T 9964-1999 闭式压力机 技术条件 ()
JC 552-1994 纤维缠绕增强热固性树脂压力管 ()
JC/T 230-1993 石英玻璃管耐内压力检验方法 ()
JC/T 434-1991（1996） 电工用石棉水泥压力板 ()
JC/T 692-1998 反渗透水处理装置用玻璃纤维增强塑料压力壳体 ()
JC/T 717-1990(1996) 地面用玻璃纤维增强塑料压力容器 ()
JC/T 960-2005 水泥胶砂强度自动压力试验机 ()
JJG(石油) 07-1999 机械式井下压力计 ()
JJG(石油) 40-1995 压力式碳酸盐岩含量测量仪 ()
JJG(石油) 9-1999 电子式井下压力计检定规程 ()
JJG(石油)07-1999(2007) 机械式井下压力计检定规程 ()
JJG（石油） 32-1994 耐（抗）震压力表 ()
MT/T 638-1996(2005) 煤矿井下煤层瓦斯压力的直接测定方法 ()
QB 2099.5-1995 家用和类似用途的电气自控制器电气自动控制压力敏感控制器的特殊要求(包括机械要求)
()
QB/T 1164-2000 压力喷雾干燥机 ()
QB/T 1292-1991 自动洗衣机用水位压力开关 ()
QB/T 1755-1993 造纸机械压力洗浆机 ()
QB/T 2072.1-1994 制糖机械压力容器通用零部件钢制平焊法兰 ()
QB/T 2072.10-1994 制糖机械压力容器通用零部件平焊法兰垫片 ()
QB/T 2072.2-1994 制糖机械压力容器通用零部件钢制平焊法兰 ()
QB/T 2072.3-1994 制糖机械压力容器通用零部件换热器用奥氏体不锈钢焊接钢管
()
QB/T 2072.4-1994 制糖机械压力容器通用零部件钢制悬挂式支座 ()
QB/T 2072.5-1994 制糖机械压力容器通用零部件无折边锥形封头 ()
QB/T 2072.6-1994 制糖机械压力容器通用零部件矩形人孔 ()
QB/T 2072.7-1994 制糖机械压力容器通用零部件视镜 ()
QB/T 2072.8-1994 制糖机械压力容器通用零部件视镜罩 ()
QB/T 2072.9-1994 制糖机械压力容器通用零部件汁汽三通阀 ()
QB/T 2909-2007 温度压力安全保护阀 Temperature/pressure
protection values
QB/T 3671-1999 压力式喷雾干燥器 ()
QC/T 217-2007 汽车用压力报警器 Pressure alarms for automobile
SB/T 10440-2007 真空和（或）压力浸注（处理）用木材防腐设备机组 ()
SD 340-1989 火力发电厂锅炉、压力容器焊接工艺评定规程 ()
SH/T 0221-1992(2003) 液化石油气密度或相对密度测定法（压力密度计法）
()
SH/T 0685-1999(2005) 液化石油气密度测定法(压力密度瓶法) ()
SH/T 0719-2002 润滑油氧化诱导期测定法（压力差示扫描量热法） ()
SH/T 0771-2005 石油产品倾点测定法（自动压力脉冲法） ()
SH/T 0790-2007 润滑脂氧化诱导期测定法（压力差示扫描量热法） Standard
test method for oxidation induction time of
lubricating greases by pressure differential
scanning calorimetry
SH/T 3074-2007 石油化工钢制压力容器 Steel pressure vessels
of petrochemical
SY/T 0323-2000 玻璃纤维增强热固性树脂压力管道施工及验收规范 ()
SY/T 10044-2002 炼油厂压力泄放装置的尺寸确定、选择和安装的推荐作法 ()
SY/T 5099-1985 石油下井仪器温度、压力分级及其匹配 ()
SY/T 5318-1991(2007) 200-J 型压力计 ()
SY/T 5346-2005 岩石毛管压力曲线的测定 ()
SY/T 5623-1997(2005) 地层孔隙压力预测检测方法 ()
SY/T 5748-1995 岩石中气体突破压力测定 ()
SY/T 6507-2000 压力容器检验规范 维护检验、定级、修理和改造 ()
SY/T 6552-2003 石油工业在用压力容器检验的推荐作法 ()
SY/T 6573-2003 最低混相压力细管实验测定法 ()
SY/T 6640-2005 电子式井下压力计校准方法 ()
SY/T 6738-2008 岩心毛管压力测量仪器通用技术条件 ()
YB 9070-1992(2006年确认) 压力容器设计管理规定 ()
YB 9073-1994(2006年确认) 钢制压力容器设计技术规定 ()
YS/T 683-2008 压力（差压）变送器现场校准规范 Calibration specification
for local mounting pressure(differential pressure)
transmitter
ISO压力标准(ISO pressure standards)
--------------------------------------------------------------------------------
编号 中文名称 英文名称
IEC 36C/172/DTS-2007 IEC/TS 62371, Ed. 1.0:额定电压超过1000V的电气设备用空心压力和非压力陶瓷和玻璃绝缘子的特征
IEC/TS 62371, Ed. 1.0: Characteristics of hollow
pressurised and unpressurised ceramic and glass
insulators for use in electrical equipment with
rated voltages greater than 1000 V
IEC 60141-4 AMD 1-1990 充油电缆和压气电缆及其附件的试验 第4部分:交流电压400kV及以下油浸纸绝缘高压力管式充油电缆及其附件
修 Test on oil-filled and gas-pressure cables
and their accessories; part 4: oil-impregnated
paper-insulated high pressure oil-filled pipe-type
cables and accessories for alternating voltages
up to and including 400 kV; amendment 1 to IEC
60141-4:1980
IEC 60141-4-1980 充油电缆和压气电缆及其附件的试验 第4部分:交流电压400kV及以下油浸纸绝缘高压力管式充油电缆及其附件
Test on oil-filled and gas-pressure cables and
their accessories. Part 4 : Oil-impregnated
paper-insulated high pressure oil-filled pipe-type
cables and accessories for alternating voltages
up to and including 400 kV
IEC 60730-2-6-2007 家用和类似用途的自动电气控制器.第2-6部分:包括机械要求的自动电气压力敏感控制器的特殊要求
Automatic electrical controls for household
and similar use - Part 2-6: Particular requirements
for automatic electrical pressure sensing controls
including mechanical requirements
IEC 60747-14-3-2001 半导体器件 第14-3部分：半导体敏感器 压力敏感器
Semiconductor devices - Part 14-3: Semiconductor
sensors; Pressure sensors
IEC 60811-3-1 AMD 1-1994 电缆绝缘和护套材料的通用试验方法 第3部分:聚氯乙稀(PVC)化合物专用方法
第1节:高温下压力试验 耐裂试验 Common test methods for insulating
and sheathing materials of electric cables -
Part 3: Methods specific to PVC compounds -
Section 1: Pressure test at high temperature
- Tests for resistance to cracking; Amendment
1
IEC 60811-3-1 AMD 2-2001 电缆绝缘和护套材料的通用试验方法 第3部分:聚氯乙烯(PVC)化合物专用方法
第1节:高温下压力试验 耐裂试 Common test methods for insulating
and sheathing materials of electric and optical
cables - Part 3-1: Methods specific to PVC compounds
- Pressure test at high temperature; Tests for
resistance to cracking; Amendment 2
IEC 60811-3-1 Corrigendum 1-1986 电缆绝缘和护套材料的通用试验方法.第3部分:聚氯乙烯(PVC)化合物专用方法.第1节:高温下压力试验.耐裂试验.
Common test methods for insulating and sheathing
materials of electric cables - Part 3 : Methods
specific to PVC compounds - Section 1: Pressure
test at high temperature - Tests for resistance
to cracking; Corrigendum 1
IEC 60811-3-1-1985 电缆绝缘和护套材料的通用试验方法 第3部分:聚氯乙烯(PVC)化合物专用方法
第1节:高温下压力试验 耐裂试验 Common test methods for insulating
and sheathing materials of electric cables.
Part 3 : Methods specific to PVC compounds.
Section One : Pressure test at high temperature
- Tests for resistance to cracking
IEC 61094-2-1992 测量传声器 第2部分:用互易对实验室标准传声器进行压力校准的基本方法
Measurement microphones; part 2: primary method
for pressure calibration of laboratory standard
microphones by the reciprocity technique
IEC 61094-5-2001 测量传声器 第5部分：用比对对工作标准传声器的压力校准方法
Measurement microphones - Part 5: Methods for
pressure calibration of working standard microphones
by comparison
IEC 61846-1998 声学 医用体外压力脉冲碎石机的声场特性和测量 Acoustics
- Characteristics and measurements of field
of pressure pulse lithotripters
IEC/TR 61015-1990 电机用刷握 施加于电刷的静压力的测量指南 Brush-holders
for electrical machines; guide to the measurement
of the static thrust applied to brushes
IEC/TR 62039-2007 HV压力下户外使用的聚合物材料的选择指南 Selection
guide for polymeric materials for outdoor use
under HV stress
ISO 10079-3-1999 医疗吸引设备 第3部分:真空或用压力驱动吸引设备 Medical
suction equipment - Part 3: Suction equipment
powered from a vacuum or pressure source
ISO 10124-1994 压力用途的无缝钢管和焊接(埋弧焊除外)钢管 层状缺陷检测用超声检验
Seamless and welded (except submerged arc-welded)
steel tubes for pressure purposes - Ultrasonic
testing for the detection of laminar imperfections
ISO 10332-1994 压力用途的无缝钢管和焊接(埋弧焊除外)钢管 验证液压防泄漏用超声波检验
Seamless and welded (except submerged arc-welded)
steel tubes for pressure purposes; ultrasonic
testing for verification of hydraulic leak-tightness
ISO 10426-4-2004 石油和天然气工业.油井固井用水泥和材料.第4部分:在大气压力下泡沫水泥浆的制备和检验
Petroleum and natural gas industries - Cements
and materials for well cementing - Part 4: Preparation
and testing of foamed cement slurries at atmospheric
pressure
ISO 10426-5-2004 石油和天然气工业.油井固井用水泥和材料.第5部分:在大气压力下固井水泥加工制剂的收缩和膨胀的测定
Petroleum and natural gas industries - Cements
and materials for well cementing - Part 5: Determination
of shrinkage and expansion of well cement formulations
at atmospheric pressure
ISO 10467-2004 压力和无压力排水和排污塑料管道系统.基于不饱和聚酯树脂的玻璃增强热固性塑料(GRP)系统
Plastics piping systems for pressure and non-pressure
drainage and sewerage - Glass-reinforced thermosetting
plastics (GRP) systems based on unsaturated
polyester (UP) resin
ISO 10501-1993 压力作用下液体输送用热塑性塑料管 压头损失的计算 Thermoplastics
pipes for the transport of liquids under pressure
- Calculation of head losses
ISO 10502-1992 航空航天.温度为230℃及以下、压力为10500 kPa下使用的聚四氟乙烯(PTFE)软管组件.采购规范
Aerospace; hose assemblies in polytetrafluoroethylene
(PTFE) for use up to 232 °C and 10500 kPa; procurement
specification
ISO 10524-1-2006 医用气体设备用的压力调节器.第1部分:压力调节器和带流量计的压力调节器
Pressure regulators for use with medical gases
- Part 1: Pressure regulators and pressure regulators
with flow-metering devices
ISO 10524-2-2005 医用气体用压力调节器.第2部分:进气压力调节器和线性压力调节器
Pressure regulators for use with medical gases
- Part 2: Manifold and line pressure regulators
ISO 10524-3-2005 医用气体设备用的压力调节器.第3部分:带气瓶阀的压力调节器
Pressure regulators for use with medical gases
- Part 3: Pressure regulators integrated with
cylinder valves
ISO 10543-1993 压力用无缝及热拉伸焊接钢管 全周边超声波厚度检测 Seamless
and hot-stretch-reduced welded steel tubes for
pressure purposes; full peripheral ultrasonic
thickness testing
ISO 10639-2004 压力和无压力给水塑料管道系统.基于不饱和聚酯树脂的玻璃增强热固性塑料(GRP)系统
Plastics piping systems for pressure and non-pressure
water supply - Glass-reinforced thermosetting
plastics (GRP) systems based on unsaturated
polyester (UP) resin
ISO 10763-1994 液压传动 端面平齐的无缝和焊接型精密钢管 尺寸及标称工作压力
Hydraulic fluid power - Plain-end, seamless
and welded precision steel tubes - Dimensions
and nominal working pressures
ISO 10767-1-1996 液压传动 系统和元件产生压力波动值的测定 第1部分:用于泵的精密方法
Hydraulic fluid power - Determination of pressure
ripple levels generated in systems and components
- Part 1: Precision method for pumps
ISO 10767-2-1999 液压传动 系统和元件产生压力波动值的测定 第2部分:用于泵的简化方法
Hydraulic fluid power - Determination of pressure
ripple levels generated in systems and components
- Part 2: Simplified method for pumps
ISO 10767-3-1999 液压传动 系统和元件产生压力波动值的测定 第3部分:用于马达的方法
Hydraulic fluid power - Determination of pressure
ripple levels generated in systems and components
- Part 3: Method for motors
ISO 10770-3-2007 液压传动.电调制液压控制阀.第3部分:压力控制阀的试验方法
Hydraulic fluid power - Electrically modulated
hydraulic control valves - Part 3: Test methods
for pressure control valves
ISO 10771-1-2002 液压传动.金属压力容器外层的压力疲劳试验.第1部分:试验方法
Hydraulic fluid power - Fatigue pressure testing
of metal pressure-containing envelopes - Part
1: Test method
ISO 11-1987 航空器 压力座舱的地面压力试验连接接头 Aircraft; Ground
pressure testing connections for pressure cabins
ISO 11242-1996 航空器 货运集装箱压力均衡要求 Aircraft - Pressure
equalization requirements for cargo containers
ISO 11484-1994 压力用途钢管 无损检验人员的资格及认证 Steel tubes
for pressure purposes - Qualification and certification
of non-destructive testing (NDT) personnel
ISO 11496-1993 压力用途的承压无缝和焊接钢管 层间不完整性检查的管端超声波检测
Seamless and welded steel tubes for pressure
purposes; ultrasonic testing of tube ends for
the detection of laminar imperfections
ISO 1167-1-2006 流体传输用热塑管、接头和组件.抗内压力的测定.第1部分:通用方法
Thermoplastics pipes, fittings and assemblies
for the conveyance of fluids - Determination
of the resistance to internal pressure - Part
1: General method
ISO 1167-2-2006 流体传输用热塑管、接头和组件.抗内压力的测定.第2部分:管试件的准备
Thermoplastics pipes, fittings and assemblies
for the conveyance of fluids - Determination
of the resistance to internal pressure - Part
2: Preparation of pipe test pieces
ISO 11673-2005 未增塑聚氯乙烯(PVC-U)压力管.断裂韧性测定 Unplasticized
poly(vinyl chloride) (PVC-U) pressure pipes
- Determination of the fracture toughness properties
ISO 12048-1994 包装 满装的运输包装 使用压力试验机的压力试验和堆积试验
Packaging - Complete, filled transport packages
- Compression and stacking tests using a compression
tester
ISO 12094-1994 压力用途的承压焊接钢管 焊接钢管用钢带/钢板分层缺陷检测用超声波试验
Welded steel tubes for pressure purposes - Ultrasonic
testing for the detection of laminar imperfections
in strips/plates used in the manufacture of
welded tubes
ISO 12095-1994 压力用途的承压无缝和焊接钢管 液体渗透试验 Seamless
and welded steel tubes for pressure purposes
- Liquid penetrant testing
ISO 12096-1996 压力用途的承压埋弧焊接钢管 焊缝缺陷检测用X射线检查 Submerged
arc-welded steel tubes for pressure purposes
- Radiographic testing of the weld seam for
the detection of imperfections
ISO 12162-1995 压力用热塑性塑料管材和管件分级和命名 总体使用(设计)系数
Thermoplastics materials for pipes and fittings
for pressure applications - Classification and
designation - Overall service (design) coefficient
ISO 12334-2000 航空航天 带压力补偿的变流量液压泵 35000 kPa系统的一般要求
Aerospace - Hydraulic, pressure-compensated,
variable delivery pumps - General requirements
for 35000 kPa systems
ISO 13460-1998 农业灌溉设备 聚乙烯压力管用塑料支管架 Agricultural
irrigation equipment - Plastics saddles for
polyethylene pressure pipes
ISO 13663-1995 压力用途的承压焊接钢管 焊缝周围分层缺陷检测用超声波试验
Welded steel tubes for pressure purposes - Ultrasonic
testing of the area adjacent to the weld seam
for the detection of laminar imperfections
ISO 13664-1997 压力用途的承压无缝和焊接钢管 管端分层组织缺陷探测用磁粉检验
Seamless and welded steel tubes for pressure
purposes - Magnetic particle inspection of the
tube ends for the detection of laminar imperfections
ISO 13665-1997 压力用途的承压无缝和焊接钢管 管身表面缺陷探测用磁粉检验
Seamless and welded steel tubes for pressure
purposes - Magnetic particle inspection of the
tube body for the detection of surface imperfections
ISO 13760-1998 流体输送用塑料压力管材 Miner's规则 累积破坏的计算方法
Plastics pipes for the conveyance of fluids
under pressure - Miner's rule - Calculation
method for cumulative damage
ISO 13761-1996 塑料管道和配件.使用温度在20℃以上的聚乙烯管道系统的压力折减系数
Plastics pipes and fittings - Pressure reduction
factors for polyethylene pipeline systems for
use at temperatures above 20 °C
ISO 13994-2005 防液体化学制品的防护服.防护服材料在压力下防液体渗透的测定
Clothing for protection against liquid chemicals
- Determination of the resistance of protective
clothing materials to penetration by liquids
under pressure
ISO 14236-2000 塑料管材和管件 给水系统聚乙烯压力管用压紧式机械连接件 Plastics
pipes and fittings - Mechanical-joint compression
fittings for use with polyethylene pressure
pipes in water supply systems
ISO 14317-2006 硬质合金除外的烧结金属材料.屈服压力强度的测定 Sintered
metal materials excluding hardmetals - Determination
of compressive yield strength
ISO 14623-2003 航天系统.压力容器及承压结构.设计与操作 Space systems
- Pressure vessels and pressurized structures
- Design and operation
ISO 15171-1-1999 用于流体传动和一般用途的管接头 诊断用液压管接头 第1部分:非压力下连接的管接头
Connections for fluid power and general use
- Hydraulic couplings for diagnostic purposes
- Part 1: Coupling not for connection under
pressure
ISO 15171-2-2000 用于流体传动和一般用途的管接头 诊断用液压管接头 第2部分:带M16×2螺纹端的压力连接接头
Connections for fluid power and general use
- Hydraulic couplings for diagnostic purposes
- Part 2: Coupling with M16 × 2 end for connection
under pressure
ISO 15265-2004 热环境的人类工效学.热工作环境中压力或不适感预防的风险评估策略
Ergonomics of the thermal environment - Risk
assessment strategy for the prevention of stress
or discomfort in thermal working conditions
ISO 15306-2003 玻璃增强热固性塑料管道.抗周期性内压力的测定 Glass-reinforced
thermosetting plastics (GRP) pipes - Determination
of the resistance to cyclic internal pressure
ISO 15364-2000 船舶与海上技术 散货船真空/压力阀 Ships and marine
technology - Pressure/vacuum valves for cargo
tanks
ISO 15379-1-2004 铝生产用碳质材料.阴极块材料.第1部分:压力作用下由于钠渗透引起的膨胀的测定
Carbonaceous materials for the production of
aluminium - Cathode block materials - Part 1:
Determination of the expansion due to sodium
penetration with application of pressure
ISO 15379-2-2004 铝生产用碳质材料.阴极块材料.第2部分:无压力作用下由于钠渗透引起的膨胀的测定
Carbonaceous materials for the production of
aluminium - Cathode block materials - Part 2:
Determination of the expansion due to sodium
penetration without application of pressure
ISO 15500-8-2001 道路车辆 压缩天然气(CNG)燃料系统部件 第6部分:压力指示器
Road vehicles - Compressed natural gas (CNG)
fuel system components - Part 8: Pressure indicator
ISO 15616-3-2003 高质量焊接和切割用CO2激光射线机的验收试验.第3部分:气体流量和压力测量仪的校正
Acceptance tests for CO<(Index)2>-laser
beam machines for high quality welding and cutting
- Part 3: Calibration of instruments for measurement
of gas flow and pressure
ISO 15821-2007 门和窗.动态压力下不透水性试验.气旋方面 Doorsets
and windows - Water-tightness test under dynamic
pressure - Cyclonic aspects
ISO 15996-2005 储气瓶.剩余压力阀.一般要求和型式试验 Gas cylinders
- Residual pressure valves - General requirements
and type testing
ISO 16028 AMD 1-2006 液压传动.在20MPa(200巴)至31.5MPa(315巴)压力下使用的平面对接型快速接头.规范.修改件1
Hydraulic fluid power - Flush-face type, quick-action
couplings for use at pressures of 20 MPa (200
bar) to 31,5 MPa (315 bar) - Specifications;
Amendment 1
ISO 16028-1999 液压传动 用于压力为20 MPa(200 bar)～31.5
MPa(315 bar)的平面对接型快速接头 规范 Hydraulic fluid power
- Flush-face type, quick-action couplings for
use at pressures of 20 MPa (200 bar) to 31,5
MPa (315 bar) - Specifications
ISO 1607-2-1989 容积真空泵 性能测量方法 第2部分:极限压力的测量 Positive-displacement
vacuum pumps; measurement of performance characteristics;
part 2: measurement of ultimate pressure
ISO 1608-2-1989 蒸气真空泵 性能特性的测量 第2部分:临界前级压力的测量
Vapour vacuum pumps; measurement of performance
characteristics; part 2: measurement of critical
backing pressure
ISO 161-1-1996 流体输送用热塑性塑料管材 公称外径和公称压力 第1部分:公制系列
Thermoplastics pipes for the conveyance of fluids
- Nominal outside diameters and nominal pressures
- Part 1: Metric series
ISO 161-2-1996 流体输送用热塑性塑料管材 公称外径和公称压力 第2部分:英制系列
Thermoplastics pipes for the conveyance of fluids
- Nominal outside diameters and nominal pressures
- Part 2: Inch-based series
ISO 16232-3-2007 道路车辆.液压管路部件清洁度.第3部分:压力漂洗萃取污染物的方法
Road vehicles - Cleanliness of components of
fluid circuits - Part 3: Method of extraction
of contaminants by pressure rinsing
ISO 16422-2006 由定向未增塑聚(氯)乙烯(PVC-O)制成的用于压力下水运输的管道和接头.规范
Pipes and joints made of oriented unplasticized
poly(vinyl chloride) (PVC-O) for the conveyance
of water under pressure - Specifications
ISO 16528-1-2007 锅炉和压力容器.第1部分:性能要求 Boilers and
pressure vessels - Part 1: Performance requirements
ISO 16528-2-2007 锅炉和压力容器.第2部分:ISO 16528-1的要求履行规程
Boilers and pressure vessels - Part 2: Procedures
for fulfilling the requirements of ISO 16528-1
ISO 16873 AMD 1-2005 液压传动.压力开关.安装表面.修改件1 Hydraulic
fluid power - Pressure switches - Mounting surfaces;
Amendment 1
ISO 16873-2002 液压传动.压力开关.安装表面 Hydraulic fluid
power - Pressure switches - Mounting surfaces
ISO 17190-7-2001 尿失禁用吸尿器 聚合基吸收材料特性化的试验方法 第7部分：比重法测定压力下的吸收
Urine-absorbing aids for incontinence - Test
methods for characterizing polymer-based absorbent
materials - Part 7: Gravimetric determination
of absorption under pressure
ISO 17230-2006 皮革.物理和机械试验.水渗透压力测定 Leather -
Physical and mechanical tests - Determination
of water penetration pressure
ISO 17484-1-2006 塑料管道系统.最大工作压力≥500 kPa的室内燃气设备用多层管道系统.第1部分:系统规范
Plastics piping systems - Multilayer pipe systems
for indoor gas installations with a maximum
operating pressure up to and including 5 bar
(500 kPa) - Part 1: Specifications for systems
ISO 17654-2003 金属材料焊接的破坏检验.电阻焊接.电阻缝焊的压力试验 Destructive
tests on welds in metallic materials - Resistance
welding - Pressure test on resistance seam welds
ISO 17744-2004 塑料.作为温度和压力函数的比容的测定(pvT图).活塞装置法
Plastics - Determination of specific volume
as a function of temperature and pressure (pvT
diagram) - Piston apparatus method
ISO 18172-1-2007 储气瓶.可再灌装的焊接不锈钢气瓶.第1部分:试验压力≤6MPa
Gas cylinders - Refillable welded stainless
steel cylinders - Part 1: Test pressure 6 MPa
and below
ISO 18172-2-2007 储气瓶.可再灌装的焊接不锈钢气瓶.第2部分:试验压力大于6MPa
Gas cylinders - Refillable welded stainless
steel cylinders - Part 2: Test pressure greater
than 6 MPa
ISO 18752-2006 橡胶软管和软管组件.金属丝或纺织物.水利用的单胎压力加强型.规范
Rubber hoses and hose assemblies - Wire- or
textile-reinforced single-pressure types for
hydraulic applications - Specification
ISO 19973-4-2007 气压传动.通过测试评定元件的可靠度.第4部分:压力调节器
Pneumatic fluid power - Assessment of component
reliability by testing - Part 4: Pressure regulators
ISO 2035-1974 压力下使用的弹性密封圈式连接的硬聚氯乙烯(PVC)注塑管件
耐压试验 Unplasticized polyvinyl chloride (PVC)
moulded fittings for elastic sealing ring type
joints for use under pressure; Pressure-resistance
test
ISO 2044-1974 压力管用注塑溶剂粘接的硬聚氯乙烯(PVC)承口管件 内水压试验
Unplasticized polyvinyl chloride (PVC) injection-moulded
solvent-welded socket fittings for use with
pressure pipe; Hydraulic internal pressure test
ISO 2045-1988 弹性密封环型连接的硬聚氯乙烯(PVC-U)和氯化聚氯乙烯(PVC-C)压力管的单承口
最小配合深度 Single sockets for unplasticized poly(vinyl
chloride) (PVC-U) and chlorinated poly(vinyl
chloride) (PVC-C) pressure pipes with elastic
sealing ring type joints; minimum depths of
engagement
ISO 2048-1990 弹性密封圈型接头的硬聚氯乙烯(PVC-U)压力管的双承口 最小配合深度
Double-socket fittings for unplasticized poly(vinyl
chloride) (PVC-U) pressure pipes with elastic
sealing ring type joints; minimum depths of
engagement
ISO 20623-2003 石油及相关产品.用4球法测定流体的极限压力和耐磨性(欧洲条件)
Petroleum and related products - Determination
of the extreme-pressure and anti-wear properties
of fluids - Four ball method (European conditions)
ISO 21750-2006 道路车辆.有关增进轮胎充气压力监控的安全 Road vehicles
- Safety enhancement in conjunction with tyre
inflation pressure monitoring
ISO 2186-2007 封闭管道中的流体流量.一次和二次元件间压力信号传送的连接件
Fluid flow in closed conduits - Connections
for pressure signal transmissions between primary
and secondary elements
ISO 22435-2007 储气瓶.带压力调节器的气缸阀.规范和类型测试 Gas cylinders
- Cylinder valves with integrated pressure regulators
- Specification and type testing
ISO 23251 Technical Corrigendum 1-2007 石油、石化和天然气工业.压力释放和降压系统.技术勘误1
Petroleum, petrochemical and natural gas industries
- Pressure-relieving and depressuring systems;
Technical Corrigendum 1
ISO 23251-2006 石油、石化和天然气工业.压力.缓解和减少系统 Petroleum,
petrochemical and natural gas industries - Pressure-relieving
and depressuring systems
ISO 23551-2-2006 气体燃烧器和燃气设备用安全和控制装置.特殊要求.第2部分:压力调节器
Safety and control devices for gas burners and
gas-burning appliances - Particular requirements
- Part 2: Pressure regulators
ISO 2536-1974 公制系列、硬聚氯乙烯(PVC)压力管材和管件 法兰尺寸 Unplasticized
polyvinyl chloride (PVC) pressure pipes and
fittings, metric series; Dimensions of flanges
ISO 2556-1974 塑料 在大气压力下薄膜和薄板的透气率的测定 测压法 Plastics;
Determination of the gas transmission rate of
films and thin sheets under atmospheric pressure;
Manometric method
ISO 2605-3-1985 压力用途的钢 高温特性的推导和验证 第3部分:在限定数据时,推导高温屈服应力或弹性极限应力特性可供选择的
Steel products for pressure purposes; Derivation
and verification of elevated temperature properties;
Part 3 : An alternative procedure for deriving
the elevated temperature yield or proof stress
properties when data are limited
ISO 294-1 AMD 2-2005 塑料.热塑性材料试样的注模塑法.第1部分:一般原则、多用途模塑件及条形试样.修改件2:吸着压力和时间的测定
Plastics - Injection moulding of test specimens
of thermoplastic materials - Part 1: General
principles, and moulding of multipurpose and
bar test specimens; Amendment 2: Methods of
determining the hold pressure and hold time
ISO 2944-2000 流体传动系统和元件 公称压力 Fluid power systems
and components - Nominal pressures
ISO 3458-1976 聚乙烯(PE)压力管材和管件间的装配接头 内压密封试验 Assembled
joints between fittings and polyethylene (PE)
pressure pipes ; Test of leakproofness under
internal pressure
ISO 3459-1976 聚乙烯(PE)压力管 用机械式管件装配的接头 内压试验法和要求
Polyethylene (PE) pressure pipes; Joints assembled
with mechanical fittings; Internal under-pressure
test method and requirement
ISO 3460-1975 硬聚氯乙烯(PVC)压力管材 公制系列 凹法兰管接头尺寸 Unplasticized
polyvinyl chloride (PVC) pressures pipes; Metric
series; Dimensions of adapter for backing flange
ISO 3501-1976 聚乙烯(PE)压力管材和管件间的装配接头 抗拉拔试验 Assembled
joints between fittings and polyethylene (PE)
pressure pipes; Test of resistance to pull out
ISO 3503-1976 聚乙烯(PE)压力管材和管件间的装配接头 弯曲时承受内压的密封试验
Assembled joints between fittings and polyethylene
(PE) pressure pipes; Test of leakproofness under
internal pressure when subjected to bending
ISO 3583-1984 道路车辆 气压制动装置的压力试验连接 Road vehicles;
Pressure test connection for compressed-air
pneumatic braking equipment
ISO 3603-1977 弹性密封圈式硬聚氯乙烯(PVC)压力管件 密封压力试验 Fittings
for unplasticized polyvinyl chloride (PVC) pressure
pipes with elastic sealing ring type joints;
Pressure test for leakproofness
ISO 3604-1976 弹性密封圈式硬聚氯乙烯(PVC)压力管件 外水压条件下的密封压力试验
Fittings for unplasticized polyvinyl chloride
(PVC) pressure pipes with elastic sealing ring
type joints; Pressure test for leakproofness
under conditions of external hydraulic pressure
ISO 3663-1976 聚乙烯(PE)压力管材和管件 公制系列 法兰尺寸 Polyethylene
(PE) pressure pipes and fittings, metric series;
Dimensions of flanges
ISO 3935-1977 造船 内河航行 消防水系统 压力 Shipbuilding;
Inland navigation; Fire-fighting water system;
Pressures
ISO 3948-1977 造船 内河船舶 压缩空气系统 压力等级 Shipbuilding;
Inland vessels; Compressed-air systems; Pressure
ranges
ISO 3993-1984 液化石油气和轻质烃类 密度或相对密度的测定 压力比重计法 Liquefied
petroleum gas and light hydrocarbons; Determination
of density or relative density; Pressure hydrometer
method
ISO 4153-1981 航空器 压力燃油的分配系统 关闭脉动压力的试验程序和极限值
Aircraft; Pressure fuel dispensing system; Test
procedure and limit value for shut-off surge
pressure
ISO 4174-1998 谷物、油籽和豆类 单维气流通过粮堆的单位压力损失的测量 Cereals,
oilseeds and pulses - Measurement of unit pressure
loss in one-dimensional air flow through bulk
grain
ISO 4179-2005 压力和非压力管道用球墨铸铁管和配件.水泥灰浆内衬 Ductile
iron pipes and fittings for pressure and non-pressure
pipelines - Cement mortar lining
ISO 4392-1-2002 液压传动.马达特性的测定.第1部分:在恒低速和恒压力下的测定
Hydraulic fluid power - Determination of characteristics
of motors - Part 1: At constant low speed and
constant pressure
ISO 4399-1995 流体传动系统和元件 管接头及其附件 公称压力系列 Fluid
power systems and components - Connectors and
associated components - Nominal pressures
ISO 45-1990 航空器 压力加油接头 Aircraft; pressure refuelling
connections
ISO 4548-6 Technical Corrigendum 1-1990 内燃机全流式机油滤清器试验方法
第6部分:静态爆破压力试验 技术勘误1 Methods of test for full-flow
lubricating oil filters for internal combustion
engines; part 6: static burst pressure test;
technical corrigendum 1
ISO 4548-6-1985 内燃机全流式机油滤清器试验方法 第6部分:静态爆破压力试验
Methods of test for full-flow lubricating oil
filters for internal combustion engines; Part
6 : Static burst pressure test
ISO 4622-1992 色漆和清漆 堆积压力试验 Paints and varnishes;
pressure test for stackability
ISO 4666-4-2007 硫化橡胶.挠曲计测试中温升和抗疲劳性测定.第4部分:恒定压力挠曲计
Rubber, vulcanized - Determination of temperature
rise and resistance to fatigue in flexometer
testing - Part 4: Constant-stress flexometer
ISO 4783-3-1981 工业用金属丝筛网和金属丝编织网 网孔尺寸和金属丝直径组合选择指南
第3部分:预弯成形或压力焊的金属丝网的 Industrial wire screens
and woven wire cloth; Guide to the choice of
aperture size and wire diameter combinations;
Part 3 : Preferred combinations for pre-crimped
or pressure-welded wire screens
ISO 485-1973 航空器的水-甲醇压力加注接头 Aircraft water-methanol
pressure connections
ISO 4991-2005 压力用途的钢铸件 Steel castings for pressure
purposes
ISO 5171-1995 焊接、切割及相关工艺用压力表 Pressure gauges
used in welding, cutting and allied processes
ISO 5208-1993 通用阀门 阀门的压力试验 Industrial valves;
pressure testing of valves
ISO 5596-1999 液压传动 隔离式充气蓄能器 压力、容积范围和特性量 Hydraulic
fluid power - Gas-loaded accumulators with separator
- Ranges of pressures and volumes and characteristic
quantities
ISO 5781-2000 液压传动 压力控制阀(不包括溢流阀)、顺序阀、卸荷阀、节流阀和单向阀
安装面 Hydraulic fluid power - Pressure-reducing
valves, sequence valves, unloading valves, throttle
valves and check valves - Mounting surfaces
ISO 6150-1988 气压传动 最高工作压力为10 bar、16 bar和25 bar(1
MPa、1.6 MPa和2.5 MPa)圆柱形快换接头、插头、连接尺寸 Pneumatic
fluid power; cylindrical quick-action couplings
for maximum working pressures of 10 bar, 16
bar and 25 bar (1 MPa, 1,6 MPa and 2,5 MPa);
plug connecting dimensions, specifications,
application guidelines and testing
ISO 6162-1 Technical Corrigendum 1-2004 液压传动.带分离式或一体式法兰夹和米制或英制螺纹的凸缘连接器.第1部分:3.5MPa至35MPa(35巴至350巴)压力下
Hydraulic fluid power - Flange connectors with
split or one-piece flange clamps and metric
or inch screws - Part 1: Flange connectors for
use at pressures of 3,5 MPa (35 bar) to 35 MPa
(350 bar), DN 13 to DN 127; Technical Corrigendum
1
ISO 6162-1-2002 液压传动.带分离式或一体式法兰夹和米制或英制螺纹的凸缘连接器.第1部分:压力为3.5MPa至35MPa(35巴至350巴)
Hydraulic fluid power - Flange connectors with
split or one-piece flange clamps and metric
or inch screws - Part 1: Flange connectors for
use at pressures of 3,5 MPa (35 bar) to 35 MPa
(350 bar), DN 13 to DN 127
ISO 6162-2-2002 液压传动.带分离式或一体式法兰夹和米制或英制螺纹的凸缘连接器.第2部分:压力为35MPa至40MPa(350巴至400巴)
Hydraulic fluid power - Flange connectors with
split or one-piece flange champs and metric
or inch screws - Part 2: Flange connectors for
use at pressures of 35 MPa (350 bar) to 40 MPa
(400 bar), DN 13 to DN 51
ISO 6164-1994 液压传动.25MPa和40MPa(250 bar和400 bar)压力下使用的四螺栓整体方法兰
Hydraulic fluid power; four-srew, one-piece
square-flange connections for use at pressures
of 25 MPa and 40 MPa (250 bar and 400 bar)
ISO 6303-1981 不包括ISO 2604第1～6部分的压力容器钢 长期受力断裂性能的推导
Pressure vessel steels not included in ISO 2604,
Parts 1 to 6; Derivation of long-time stress
rupture properties
ISO 6403-1988 液压传动 控制流量及压力的阀 试验方法 Hydraulic
fluid power; valves controlling flow and pressure;
test methods
ISO 6771-2007 航空航天.流体系统和部件.压力和温度分类 Aerospace
- Fluid systems and components - Pressure and
temperature classifications
ISO 6822-1984 马铃薯、根类蔬菜和结球甘蓝 在地下仓库中用压力通风的贮存指南
Potatoes, root vegetables and round-headed cabbages;
Guide to storage in silos using forced ventilation
ISO 683-10-1987 热处理钢、合金钢和易切钢 第10部分:压力加工渗氮钢 Heat-treatable
steels, alloy steels and free-cutting steels;
Part 10 : Wrought nitriding steels
ISO 683-11-1987 热处理钢、合金钢和易切钢 第11部分:压力加工表面硬化钢
Heat-treatable steels, alloy steels and free-cutting
steels; Part 11 : Wrought case-hardening steels
ISO 6898-1984 开式机械压力机 性能及尺寸 Open front mechanical
power presses; Capacity ratings and dimensions
ISO 6899-1984 开式机械动力压力机验收条件 精度检验 Acceptance
conditions of open front mechanical power presses;
Testing of the accuracy
ISO 6993-1-2006 输送气体燃料用埋设的、高耐冲击的聚氯乙烯(PVC-HI)管道.第1部分:最大操作压力为1巴(100
kPa)的管子 Buried, high-impact poly(vinyl chloride)
(PVC-HI) piping systems for the supply of gaseous
fuels - Part 1: Pipes for a maximum operating
pressure of 1 bar (100 kPa)
ISO 6993-2-2006 输送气体燃料用埋设的、高耐冲击的聚氯乙烯(PVC-HI)管道.第2部分:最大操作压力为200mbar(20
kPa)的管件 Buried, high-impact poly(vinyl chloride)
(PVC-HI) piping systems for the supply of gaseous
fuels - Part 2: Fittings for a maximum operating
pressure of 200 mbar (20 kPa)
ISO 6993-3-2006 输送气体燃料用埋设的、高耐冲击的聚氯乙烯(PVC-HI)管道.第3部分:最大操作压力为1巴(100
kPa)的管件和鞍座 Buried, high-impact poly(vinyl chloride)
(PVC-HI) piping systems for the supply of gaseous
fuels - Part 3: Fittings and saddles for a maximum
operating pressure of 1 bar (100 kPa)
ISO 7-1 Technical Corrigendum 1-2007 螺纹上有压力密封接缝的管螺纹.第1部分:尺寸、公差和标志.技术勘误1
Pipe threads where pressure-tight joints are
made on the threads - Part 1: Dimensions, tolerances
and designation; Technical Corrigendum 1
ISO 7169-2007 航空航天.液压系统用24°锥形的、压力范围截至3000psi或21000kPa的可拆卸管接头.采购规范(英制/米制)
Aerospace - Separable tube fittings for fluid
systems, for 24° cones, for pressures up to
3000 psi or 21000 kPa - Procurement specification,
inch/metric
ISO 7268 AMD 1-1984 管道元件 公称压力的定义 修改1 Amendment
1-1984
ISO 7268-1983 管道元件 公称压力的定义 Pipe components;
Definition of nominal pressure
ISO 727-1-2002 压力管件用由未增塑的聚氯乙烯,氯化聚氯乙烯或丙烯腈/丁二烯/苯乙烯制的带普通管套的管配件.第1部分:米制系
Fittings made from unplasticized poly(vinyl
chloride) (PVC-U), chlorinated poly(vinyl chloride)
(PVC-C) or acrylonitrile/butadiene/styrene (ABS)
with plain sockets for pipes under pressure
- Part 1: Metric series
ISO 727-2-2005 压力管件用由未增塑聚氯乙烯、氯化聚氯乙烯或丙烯腈/丁二烯/苯乙烯制的带普通管套的管配件.第2部分:英制系
Fittings made from unplasticized poly(vinyl
chloride) (PVC-U), chlorinated poly(vinyl chloride)
(PVC-C) or acrylonitrile/butadiene/styrene (ABS)
with plain sockets for pipes under pressure
- Part 2: Inch-based series
ISO 7291-1999 气焊设备 用于300 bar以下的焊接、切割及相关工艺用汇流系统上的压力调节器
Gas welding equipment - Pressure regulators
for manifold systems used in welding, cutting
and allied processes up to 300 bar
ISO 7458-2004 玻璃容器.耐内压力.试验方法 Glass containers
- Internal pressure resistance - Test methods
ISO 7509-2000 塑料管道系统 玻璃纤维增强热固性塑料(GRP)管材 持续内压力下破坏时间的测定
Plastics piping systems - Glass-reinforced thermosetting
plastics (GRP) pipes - Determination of time
to failure under sustained internal pressure
ISO 7751-1991 橡胶和塑料软管和软管组件 试验压力和爆破压力对设计工作压力的比值
Rubber and plastics hoses and hose assemblies;
ratios of proof and burst pressure to design
working pressure
ISO 8169-1984 作物保护设备 喷雾器 喷嘴和压力计的连接尺寸 Equipment
for crop protection; Sprayers; Connecting dimensions
for nozzles and manometers
ISO 8278-1986 航空航天 液压式压力补偿变流量泵 一般要求 Aerospace;
Hydraulic, pressure compensated, variable delivery
pumps; General requirements
ISO 8502-3-1992 涂装油漆和有关产品前钢材预处理 表面清洁度的评定试验 第3部分:油漆前预处理后的钢材表面上的灰尘评定(压
Preparation of steel substrates before application
of paint and related products; tests for the
assessment of surface cleanliness; part 3: assessment
of dust on steel surfaces prepared for painting
(pressure-sensitive tape method)
ISO 8536-10-2004 医用输液器具.第10部分:与压力输液仪一起使用的流体线路附件
Infusion equipment for medical use - Part 10:
Accessories for fluid lines for use with pressure
infusion equipment
ISO 8536-11-2004 医用输液器具.第11部分:与压力输液仪一起使用的输液过滤器
Infusion equipment for medical use - Part 11:
Infusion filters for use with pressure infusion
equipment
ISO 8536-8-2004 医用输液器具.第8部分:有压力输液仪的输液器具 Infusion
equipment for medical use - Part 8: Infusion
equipment for use with pressure infusion apparatus
ISO 8536-9-2004 医用输液器具.第9部分:与压力输液仪一起使用的流体线路
Infusion equipment for medical use - Part 9:
Fluid lines for use with pressure infusion equipment
ISO 8540-1993 开式机械压力机 词汇 两种语言版 Open front mechanical
power presses; vocabulary
ISO 8572-1991 玻璃纤维增强热塑性塑料管材和管件 与压力有关的定义,包括它们之间关系,以及安装和连接的术语
Pipes and fittings made of glass-reinforced
thermosetting plastics (GRP); definitions of
terms relating to pressure, including relationships
between them, and terms for installation and
jointing
ISO 8625-1-1993 航空航天 流体系统 词汇 第1部分:与压力有关的通用术语和定义
两种语言版 Aerospace; fluid systems; vocabulary;
part 1: general terms and definitions relating
to pressure
ISO 8756-1994 空气质量 温度、压力和湿度的数据处理 Air quality;
handling of temperature, pressure and humidity
data
ISO 8773-2006 无压力地下排水和排污塑料管道系统.聚丙烯(PP) Plastics
piping systems for non-pressure underground
drainage and sewerage - Polypropylene (PP)
ISO 9110-2-1990 液压传动 测量技术 第2部分:密闭回路中平均稳定压力的测量
Hydraulic fluid power; measurement techniques;
part 2: measurement of average steady-state
pressure in a closed conduit
ISO 9188-1993 机床 公称力从400 kN到4000 kN(含4000 kN)单动机械式矫直压力机
特性和尺寸 Machine tools; straight-sided single-action
mechanical power presses from 400 kN up to and
including 4000 kN nominal force; characteristics
and dimensions
ISO 9189-1993 机床 公称力从250 kN到4000 kN(含4000 kN)单动高速机械式矫直压力机
特性和尺寸 Machine tools; straight-sided high-speed
mechanical power presses from 250 kN up to and
including 4000 kN nominal force; characteristics
and dimensions
ISO 9302-1994 压力用途的无缝钢管和焊接(埋弧焊除外)钢管 液压密封验证电磁试验法
Seamless and welded (except submerged arc-welded)
steel tubes for pressure purposes; electromagnetic
testing for verification of hydraulic leak-tightness
ISO 9303-1989 压力用途的无缝钢管和焊接(埋弧焊除外)钢管 检测纵向缺陷用全周边超声波试验
Seamless and welded (except submerged arc-welded)
steel tubes for pressure purposes; full peripheral
ultrasonic testing for the detection of longitudinal
imperfections
ISO 9304-1989 压力用途的无缝钢管和焊接(埋弧焊除外)钢管 检测缺陷用涡流电流试验
Seamless and welded (except submerged arc-welded)
steel tubes for pressure purposes; eddy current
testing for the detection of imperfections
ISO 9305-1989 压力用途的无缝钢管 横向缺陷全周边超声电流检验 Seamless
steel tubes for pressure purposes; full peripheral
ultrasonic testing for the detection of transverse
imperfections
ISO 9311-3-2005 热塑性管道系统用胶粘剂.第3部分:测定耐内压力性的试验方法
Adhesives for thermoplastic piping systems -
Part 3: Test method for the determination of
resistance to internal pressure
ISO 9327-1-1999 压力用途的钢锻件和轧制或锻造的棒材 交货技术条件 第1部分:一般要求
Steel forgings and rolled or forged bars for
pressure purposes - Technical delivery conditions
- Part 1: General requirements
ISO 9327-2-1999 压力用途的钢锻件和轧制或锻造的棒材 交货技术条件 第2部分:具有规定的高温度特性的非合金和合金钢(钼、镉
Steel forgings and rolled or forged bars for
pressure purposes - Technical delivery conditions
- Part 2: Non-alloy and alloy (Mo, Cr and CrMo)
steels with specified elevated temperature properties
ISO 9327-3-1999 压力用途的钢锻件和轧制或锻造的棒材 交货技术条件 第3部分:具有规定的低温度特性的镍钢
Steel forgings and rolled or forged bars for
pressure purposes - Technical delivery conditions
- Part 3: Nickel steels with specified low temperature
properties
ISO 9327-4-1999 压力用途的钢锻件和轧制或锻造的棒材 交货技术条件 第4部分:高强度可焊接细粒钢
Steel forgings and rolled or forged bars for
pressure purposes - Technical delivery conditions
- Part 4: Weldable fine grain steels with high
proof strength
ISO 9327-5-1999 压力用途的钢锻件和轧制或锻造的棒材 交货技术条件 第5部分:不锈钢
Steel forgings and rolled or forged bars for
pressure purposes - Technical delivery conditions
- Part 5: Stainless steels
ISO 9328-1-2003 压力用途的扁钢产品.交货技术条件.第1部分:一般要求 Steel
flat products for pressure purposes - Technical
delivery conditions - Part 1: General requirements
ISO 9328-2-2004 压力用途的扁钢制品.交货技术条件.第2部分:规定了高温性能的非合金和合金钢
Steel flat products for pressure purposes -
Technical delivery conditions - Part 2: Non-alloy
and alloy steels with specified elevated temperature
properties
ISO 9328-3-2004 压力用途扁钢产品.交货技术条件.第3部分:正火可焊细粒钢
Steel flat products for pressure purposes -
Technical delivery conditions - Part 3: Weldable
fine grain steels, normalized
ISO 9328-4-2004 压力用途扁钢产品.交货技术条件.第4部分:规定了低温性能的镍合金钢
Steel flat products for pressure purposes -
Technical delivery conditions - Part 4: Nickel-alloy
steels with specified low temperature properties
ISO 9328-5-2004 压力用途扁钢产品.交货技术条件.第5部分:热机辊轧可焊细粒钢
Steel flat products for pressure purposes -
Technical delivery conditions - Part 5: Weldable
fine grain steels, thermomechanically rolled
ISO 9328-6-2004 压力用途扁钢产品.交货技术条件.第6部分:淬火和回火的可焊接细粒钢
Steel flat products for pressure purposes -
Technical delivery conditions - Part 6: Weldable
fine grain steels, quenched and tempered
ISO 9328-7-2004 压力用途扁钢产品.交货技术条件.第7部分:不锈钢 Steel
flat products for pressure purposes - Technical
delivery conditions - Part 7: Stainless steels
ISO 9329-1-1989 压力用途的无缝钢管 交货技术条件 第1部分:规定室温性能的非合金钢
Seamless steel tubes for pressure purposes;
technical delivery conditions; part 1: unalloyed
steels with specified room temperature properties
ISO 9329-2-1997 压力用途的无缝钢管 交货技术条件 第2部分:规定高温性能的非合金钢和合金钢
Seamless steel tubes for pressure purposes -
Technical delivery conditions - Part 2: Unalloyed
and alloyed steels with specified elevated temperature
properties
ISO 9329-3-1997 压力用途的无缝钢管 交货技术条件 第3部分:规定低温性能的非合金钢和合金钢
Seamless steel tubes for pressure purposes -
Technical delivery conditions - Part 3: Unalloyed
and alloyed steels with specified low temperature
properties
ISO 9329-4-1997 压力用途的无缝钢管 交货技术条件 第4部分:奥氏体不锈钢
Seamless steel tubes for pressure purposes -
Technical delivery conditions - Part 4: Austenitic
stainless steels
ISO 9330-1-1990 压力用途的焊接钢管 交货技术条件 第1部分:规定室温性能的非合金钢管
Welded steel tubes for pressure purposes; technical
delivery conditions; part 1: unalloyed steel
tubes with specified room temperatures properties
ISO 9330-2-1997 压力用途的焊接钢管 交货技术条件 第2部分:规定高温性能的电阻焊接和感应焊接非合金钢管和合金钢管
Welded steel tubes for pressure purposes - Technical
delivery conditions - Part 2: Electric resistance
and induction welded unalloyed and alloyed steel
tubes with specified elevated temperature properties
ISO 9330-3-1997 压力用途的焊接钢管 交货技术条件 第3部分:规定低温性能的电阻焊接和感应焊接非合金钢管和合金钢管
Welded steel tubes for pressure purposes - Technical
delivery conditions - Part 3: Electric resistance
and induction welded unalloyed and alloyed steel
tubes with specified low temperature properties
ISO 9330-4-2000 压力用途的焊接钢管 交货技术条件 第4部分:规定高温性能的埋弧焊接非合金钢管和合金钢管
Welded steel tubes for pressure purposes - Technical
delivery conditions - Part 4: Submerged arc-welded
unalloyed and alloyed steel tubes with specified
elevated temperature properties
ISO 9330-5-2000 压力用途的焊接钢管 交货技术条件 第5部分:规定低温性能的埋弧焊接非合金钢管和合金钢管
Welded steel tubes for pressure purposes - Technical
delivery conditions - Part 5: Submerged arc-welded
unalloyed and alloyed steel tubes with specified
low temperature properties
ISO 9330-6-1997 压力用途的焊接钢管 交货技术条件 第6部分:奥氏体不锈钢管的焊接长度
Welded steel tubes for pressure purposes - Technical
delivery conditions - Part 6: Longitudinally
welded austenitic stainless steel tubes
ISO 9393-1-2004 工业用热塑性阀门.压力试验方法和要求.第1部分:总则 Thermoplastics
valves for industrial applications - Pressure
test methods and requirements - Part 1: General
ISO 9393-2-2005 工业用热塑性阀门.压力试验方法和要求.第2部分:试验条件和基本要求
Thermoplastics valves for industrial applications
- Pressure test methods and requirements - Part
2: Test conditions and basic requirements
ISO 9402-1989 压力用途的无缝钢管和焊接(埋弧焊除外)钢管 检测纵向缺陷用铁磁钢管全周边磁转换/磁链试验
Seamless and welded (except submerged arc-welded)
steel tubes for pressure purposes; full peripheral
magnetic transducer/flux leakage testing of
ferromagnetic steel tubes for the detection
of longitudinal imperfections
ISO 9457-2-1994 道路车辆.米制起动电机小齿轮.第2部分:具有20度压力角的小齿轮
Road vehicles - Metric starter motor pinions
- Part 2: Pinions with 20° pressure angle
ISO 9598-1989 压力用途的无缝钢管 检测横向缺陷用铁磁钢管全周边磁转换/磁链试验
Seamless steel tubes for pressure purposes;
full peripheral magnetic transducer/flux leakage
testing of ferromagnetic steel tubes for the
detection of transverse imperfections
ISO 9623-1997 压力流体用聚乙烯(PE)/金属和聚丙烯(PP)/金属接头管件
螺纹的设计长度和尺寸 公制系列 PE/metal and PP/metal adaptor
fittings for pipes for fluids under pressure
- Design lengths and size of threads - Metric
series
ISO 9624-1997 压力流体用热塑性塑料管材 法兰接头和活套法兰的适配尺寸 Thermoplastics
pipes for fluids under pressure - Mating dimensions
of flange adapters and loose backing flanges
ISO 9625-1993 灌溉用聚乙烯压力管的机械式连接管件 Mechanical joint
fittings for use with polyethylene pressure
pipes for irrigation purposes
ISO 9644 AMD 1-1998 农业灌溉设备 灌溉阀压力损失 试验方法 修改1
Agricultural irrigation equipment - Pressure
losses in irrigation valves - Test method; Amendment
1
ISO 9644-1993 农业灌溉设备 灌溉阀压力损失 试验方法 Agricultural
irrigation equipment; pressure losses in irrigation
valves; test method
ISO 9662-1994 航空器设备 机载设备的环境和工作条件 湿度、温度和压力试验
Aircraft equipment; environmental and operating
conditions for airborne equipment; humidity,
temperature and pressure tests
ISO 9764-1989 压力用途的电阻焊和感应焊钢管 焊缝的纵向缺陷超声波检验 Electric
resistance and induction welded steel tubes
for pressure purposes; ultrasonic testing of
the weld seam for the detection of longitudinal
imperfections
ISO 9765-1990 压力用途的埋弧焊钢管 焊缝的纵向和/或横向缺陷超声波检测 Submerged
arc-welded steel tubes for pressure purposes;
ultrasonic testing of the weld seam for the
detection of longitudinal and/or transverse
imperfections
ISO 9853-1991 压力管道系统用硬聚氯乙烯(PVC-U)管件 扁平试验 Injection-moulded
unplasticized poly(vinyl chloride) (PVC-U) fittings
for pressure pipe systems; crushing test
ISO 9863-1-2005 土工织物.规定压力下厚度的测定.第1部分:单层 Geosynthetics
- Determination of thickness at specified pressures
- Part 1: Single layers
ISO 9863-2-1996 土工布及相关产品 特定压力下厚度的测定 第2部分:多层制品中单层厚度测定程序
Geotextiles and geotextile-related products
- Determination of thickness at specified pressures
- Part 2: Procedure for determination of thickness
of single layers of multilayer products
ISO 9939-1994 航空航天 滑油的压力加油接头(新型) Aerospace;
pressure re-oiling connection (new type)
ISO/TR 10501-1993 压力作用下液体输送用热塑性塑料管.压头损失的计算 Thermoplastics
pipes for the transport of liquids under pressure;
calculation of head losses
ISO/TR 7468-1981 锅炉和压力容器用锻钢的平均应力断裂特性的概述 Summary
of average stress rupture properties of wrought
steels for boilers and pressure vessels
ISO/TS 17892-8 Technical Corrigendum 1-2006
土工勘查和检验.土壤的实验室检验.第8部分:松散土壤三轴向压力试验 Geotechnical
investigation and testing - Laboratory testing
of soil - Part 8: Unconsolidated undrained triaxial
test
ISO/TS 17892-9 Technical Corrigendum 1-2006
土工勘查和检验.土壤的实验室检验.第9部分:渗水土壤的固定三轴向压力试验 Geotechnical
investigation and testing - Laboratory testing
of soil - Part 9: Consolidated triaxial compression
tests on water-saturated soils
ISO/TS 18226-2006 塑料管材和管件.压力4 MPa(40 bar)的供气体燃料用加固热塑管道系统
Plastics pipes and fittings - Reinforced thermoplastics
pipe systems for the supply of gaseous fuels
for pressures up to 4 MPa (40 bar)
日本压力标准(JIS pressure standards)
--------------------------------------------------------------------------------
编号 中文名称
日本語標題 英文名称
JIS A1128-2005 用压力法测定新浇混凝土空气含量的试验方法
フレッシュコンクリートの空気量の圧力による試験方法－空気室圧力方法 Method of
test for air content of fresh concrete by pressure
method
JIS A1517-1996 窗和门组合件.动态压力的水密性试验
建具の水密性試験方法 Windows and doorsets -- Watertightness
test under dynamic pressure
JIS A9108-1997 用压力加工法经防腐剂处理的基木
土台用加圧式防腐処理木材(廃止) Foundation wood sill treated
with preservatives by pressure processes
JIS B0190-1986 压力容器结构用术语汇编
圧力容器の構造共通用語 Glossary of terms used in construction
of pressure vessels
JIS B6402-1997 机械压力机.精度测试
機械プレス ― 精度検査 Mechanical power presses -- Testing
of the accuracy
JIS B6406-1991 机械压力机.A-加权声压级测量方法
プレス機械 ― 騒音レベル測定方法 Mechanical presses -- Methods
of measurement of A-weighted sound pressure
level
JIS B6420-1992 压力机械.操作符号
プレス機械 ― 操作表示記号 Presswork machinery -- Symbols
for operations
JIS B6451-1996 闭式双柱压力机.特性和尺寸
ストレートサイド形プレス ― 仕様及び作業面に関する寸法 Straight-sided
power presses -- Characteristics and dimensions
JIS B6471-1987 闭模压力机锻造用模块
型鍛造プレス用ダイブロック Die blocks for closed-die press
forging
JIS B6803-2003 焊接、切割及相关工艺用压力调节器
溶断器用圧力調整器 Pressure regulator for welding, cutting
and allied processes
JIS B7529-1979 蒸气压力温度计
蒸気圧式指示温度計 Vapour pressure thermometers
JIS B7610-1-2000 压力平衡.第1部分:计量要求
重錘形圧力天びん ― 第１部：計量?技術上の要件 Pressure balances --
Part 1: Metrological requirements
JIS B7610-2-2000 压力平衡.第2部分:试验方法
重錘形圧力天びん ― 第２部：試験方法 Pressure balances -- Part
2: Test methods
JIS B7610-3-2000 压力平衡.第3部分:操作程序和条件
重錘形圧力天びん ― 第３部：使用方法及び使用条件 Pressure balances
-- Part 3: Operation procedure and conditions
JIS B8006-1986 往复式内燃机性能的压力测量
往復動内燃機関の性能に関する圧力計測方法 Pressure measurements of
performance for reciprocating internal combustion
engines
JIS B8210-2009 蒸汽锅炉和压力容器.弹簧加载安全阀
蒸気用及びガス用ばね安全弁 Safety devices for protection
against excessive pressure -- Direct spring
loaded safety valves for steam and gas service
JIS B8238-1994 液化石油气用压力调节器
ＬＰガス用圧力調整器 Pressure regulators for liquefied
petroleum gas
JIS B8240-1986 致冷用压力容器的结构
冷凍用圧力容器の構造 Construction of pressure vessels
for refrigeration
JIS B8247-1999 压力容器封头
圧力容器用鏡板 Formed head for pressure vessel
JIS B8247 AMD 1-2006 压力容器封头（修改件1）
圧力容器用鏡板（追補１） Formed head for pressure vessel
(Amendment 1)
JIS B8248-1994 圆柱形双层压力容器
円筒形多層圧力容器 Cylindrical layered pressure vessels
JIS B8265-2003 压力容器的结构.一般原则
圧力容器の構造 ― 一般事項 Construction of pressure vessel
-- General principles
JIS B8265 AMD 1-2006 压力容器的结构.一般原则（修改件1）
圧力容器の構造―一般事項（追補１） Construction of pressure vessel
-- General principles (Amendment 1)
JIS B8265 AMD 2-2008 压力容器的结构.一般原则（修改件2）
圧力容器の構造―一般事項（追補２） Construction of pressure vessel
-- General principles (Amendment 2)
JIS B8266-2003 压力容器结构用替换标准
圧力容器の構造 ― 特定規格 Alternative standard for construction
of pressure vessels
JIS B8266 AMD 1-2006 压力容器制造用代替标准( 修改件1)
圧力容器の構造―特定規格（追補1） Alternative standard for construction
of pressure vessels (Amendment 1)
JIS B8274-2008 压力容器用平管板
圧力容器の管板 Flat tubesheet for pressure vessels
JIS B8277-2003 压力容器用膨胀接合
圧力容器の伸縮継手 Expansion joint for pressure vessels
JIS B8278-2003 鞍座支撑式水平压力容器
サドル支持の横置圧力容器 Saddle supported horizontal pressure
vessels
JIS B8279-2003 压力容器罩
圧力容器のジャケット Jacket for pressure vessels
JIS B8280-2003 非圆形横截面的压力容器
非円形胴の圧力容器 Pressure vessels of noncircular cross
section
JIS B8284-2003 压力容器用快速关闭
圧力容器の急速開閉ふた装置 Quick closure for pressure vessels
JIS B8285-2003 压力容器的焊接程序合格鉴定试验
圧力容器の溶接施工方法の確認試験 Welding procedure qualification
test for pressure vessels
JIS B8286-2005 压力容器用观察镜
圧力容器用のぞき窓 Sight glasses for pressure vessels
JIS B8316-2-1999 容积真空泵.性能特性的测定.第2部分:极限压力的测定
容積移送式真空ポンプ ― 性能試験方法 ― 第２部：到達圧力の測定 Positive-displacement
vacuum pumps -- Measurement of performance characteristics
-- Part 2: Measurement of ultimate pressure
JIS B8317-2-1999 蒸气真空泵.性能特性测量.第2部分:临界托持压力的测量
蒸気噴射真空ポンプ ― 性能試験方法 ― 第２部：臨界背圧の測定 Vapour vacuum
pumps -- Measurement of performance characteristics
-- Part 2: Measurement of critical backing pressure
JIS B8349-2-2004 液压传动.系统和组件中产生的压力波动级别的测定.第2部分:泵的简化法
油圧－システム及び機器から発生する圧力脈動レベルの測定方法－第２部：ポンプにおける簡易測定方法
Hydraulic fluid power -- Determination of pressure
ripple levels generated in systems and components
-- Part 2: Simplified method for pumps
JIS B8356-7-2006 液压动力.过滤器.过滤器性能的评价.第7部分:微分压力与流动特性关系的评价
油圧用フィルタ性能評価方法―第７部：差圧―流量特性試験 Hydraulic fluid
power -- Filters -- Evaluation of filter performance
-- Part 7: Evaluation of differential pressure
versus flow characteristics
JIS B8357-2000 液压动力.带压力补偿的流量控制阀.安装面
油圧用圧力補償付流量調整弁 ― 取付面及び取付寸法 Hydraulic fluid power
-- Compensated flow-control valves -- Mounting
surfaces
JIS B8366-2-2000 流体动力系统和元件.液压缸.元件和识别码.第2部分:标称压力
油圧?空気圧システム及び機器 ― シリンダ ― 構成要素及び識別記号 ― 第２部：呼び圧力
Fluid power systems and components -- Cylinders
-- Elements and identification code -- Part
2: Nominal pressures
JIS B8372-1-2003 液压流体动力.压缩空气压力调节器和过滤调节器.第1部分:厂商资料和产品生产要求应包含的主要特性
空気圧 ― 空気圧用減圧弁及びフィルタ付減圧弁 ― 第１部：供給者の文書に表示する主要特性及び製品表示要求事項
Pneumatic fluid power -- Compressed air pressure
regulators and filter-regulators -- Part 1:
Main characteristics to be included in literature
from suppliers and product-making requirements
JIS B8372-2-2003 气动流体动力.压缩空气压力调节器和过滤调节器.第2部分:厂商资料应包含的主要特性测定的试验方法
空気圧 ― 空気圧用減圧弁及びフィルタ付減圧弁 ― 第２部：供給者の文書に表示する主要特性の試験方法
Pneumatic fluid power -- Compressed air pressure
regulators and filter-regulators -- Part 2:
Test methods to determine the main characteristics
to be included in literature from suppliers
JIS B8397-2002 液压流体动力.带分离器的气-液蓄压器.压力和容积的范围及特征数量
油圧 ― セパレータ付き気体式アキュムレータ ― 圧力及び容積の範囲並びに特性 Hydraulic
fluid power -- Gas-loaded accumulators with
separator -- Ranges of pressures and volumes
and characteristic quantities
JIS B8409-1994 燃油器用压力式电磁泵
油バーナ用圧力形電磁ポンプ Pressure type solenoid pumps for
oil burners
JIS B8409 AMD 1-2006 燃油器用压力式电磁泵（修改件1）
油バーナ用圧力形電磁ポンプ（追補１） Pressure type solenoid pumps
for oil burners (Amendment 1)
JIS B8418-2000 非压力式热水器
無圧式温水発生機 Non pressure type hot water generator
JIS B8660-2000 液压动力.流量和压力控制阀.试验方法
油圧 ― 制御弁（流れ?圧力） ― 試験方法 Hydraulic fluid power
-- Valves controlling flow and pressure -- Test
methods
JIS B8664-2001 液压流体动力.压力控制阀(不包括减压阀)、顺序活门、释荷阀、节流阀和止回阀.
安装表面
油圧―減圧弁，シーケンス弁，アンロード弁，絞り弁及びチェック弁―取付面 Hydraulic
fluid power -- Pressure-control valves (excluding
pressure-relief valves), sequence valves, unloading
valves, throttle valves and check valves --
Mounting surfaces
JIS B8667-2004 液压传动.压力开关.安装表面
油圧－圧力スイッチ－取付面及び取付寸法 Hydraulic fluid power --
Pressure switches -- Mounting surfaces
JIS B8670-2004 流体动力系统和元件.标称压力
油圧?空気圧システム及び機器－呼び圧力 Fluid power systems and
components -- Nominal pressures
JIS B9939-2-2003 液压流体动力.测量技术.第2部分:封闭管道中平均稳态压力的测量
油圧 ― 測定技術 ― 第２部：管路における平均定常圧力の測定 Hydraulic fluid
power -- Measurement techniques -- Part 2: Measurement
of average steady-state pressure in a closed
conduit
JIS B9950-1993 压力摆转吸收器.词汇
圧力スイング吸着装置用語 Pressure swing adsorption apparatus
-- Vocabulary
JIS B9951-1993 压力摆动吸收器.试验方法
圧力スイング吸着装置 ― 性能試験方法 Pressure swing adsorption
apparatus -- Test methods
JIS C1031-1990 工业过程控制系统用压力和压差传感器的性能评价方法
工業プロセス用圧力?差圧伝送器の試験方法 Methods of evaluating the
performance of pressure and differential pressure
transmitters for use in industrial-process control
systems
JIS C1507-2006 电声学.声音强度的测量用仪器.双压力传感扩音器的测量
電気音響―音響インテンシティ測定器―圧力形ペアマイクロホンによる測定 Electroacoustics
-- Instruments for the measurement of sound
intensity -- Measurement with pairs of pressure
sensing microphones
JIS C2813-1992 建筑物电气装置用弹簧压力型电线连接器
屋内配線用差込形電線コネクタ Spring pressure type wire connectors
for electrical installations of buildings
JIS C3660-3-1-2003 电缆和光缆的绝缘和铠装材料的通用试验方法.第3-1部分:聚氯乙烯复合物专用方法.高温下压力试验.耐裂性试验
電気?光ケーブルの絶縁体及びシース材料の共通試験方法 ― 第３－１部：ビニルコンパウンドの試験方法 ― 加熱変形試験 ― 巻付加熱試験
Common test methods for insulating and sheathing
materials of electric and optical cables --
Part 3-1: Methods specific to PVC compounds
-- Pressure test at high temperature -- Test
for resistance to cracking
JIS C8367-1997 家用设备用机电压力式衡温器
圧力式サーモスタット Electromechanical pressure type thermostats
for household appliances
JIS D5803-1987 汽车润滑油压力警报灯开关
自動車用油圧表示灯スイッチ Warning lamp switches of lubricating
oil pressure for automobiles
JIS D5814-1988 汽车用真空压力开关
自動車用バキュームスイッチ Vacuum pressure switches for automobiles
JIS E4118-2004 铁路机车车辆用波登管压力计
鉄道車両用ブルドン管圧力計 Bourdon tube pressure gauges for
railway rolling stock
JIS F0504-1989 船上机械装置用减压阀的应用和设定压力
機関部逃し弁の装備及び設定圧力 Application and setting pressure
of relief valves for ships' machinery
JIS F7003-1997 造船.船用压力表的应用
船舶 ― 圧力計の装備基準 Shipbuilding -- Application of
pressure gauges on board
JIS F7341-1996 造船.锻钢制100K压力计阀
船用鍛鋼１００Ｋ圧力計弁(廃止) Shipbuilding -- Forged steel
100K pressure gauge valves
JIS F7343-1996 造船.青铜制20K压力计旋塞
船用青銅２０Ｋ圧力計コック Shipbuilding -- Bronze 20K pressure
gauge cocks
JIS F9701-2005 造船.压力开关
船用圧力スイッチ Shipbuilding -- Pressure switches
JIS F9704-1999 船舶用电子压力传感器
船用電気式圧力発信器 Marine electronic pressure transmitters
JIS G0801-1993 压力容器用钢板的超声检验
圧力容器用鋼板の超音波探傷検査方法 Ultrasonic examination of
steel plates for pressure vessels
JIS G3103-2007 锅炉和压力容器用碳钢和钼合金钢厚板材
ボイラ及び圧力容器用炭素鋼及びモリブデン鋼鋼板 Carbon steel and molybdenum
alloy steel plates for boilers and pressure
vessels
JIS G3115-2005 中温设备压力容器用钢板
圧力容器用鋼板 Steel plates for pressure vessels for
intermediate temperature service
JIS G3118-2005 中温设备压力容器用碳素钢板
中?常温圧力容器用炭素鋼鋼板 Carbon steel plates for pressure
vessels for intermediate and moderate temperature
services
JIS G3119-2007 锅炉和压力容器用锰-钼和锰-钼-镍合金钢厚板材
ボイラ及び圧力容器用マンガンモリブデン鋼及びマンガンモリブデンニッケル鋼鋼板 Manganese-molybdenum
and manganese-molybdenum-nickel alloy steel
plates for boilers and pressure vessels
JIS G3120-2009 压力容器用淬火和回火的锰钼及锰钼镍合金钢板
圧力容器用調質型マンガンモリブデン鋼及びマンガンモリブデンニッケル鋼鋼板 Manganese-molybdenum
and manganese-molybdenum-nickel alloy steel
plates quenched and tempered for pressure vessels
JIS G3124-2004 中温压力容器用高强度钢板
中?常温圧力容器用高強度鋼鋼板 High strength steel plates for
pressure vessel for intermediate and moderate
temperature service
JIS G3126-2009 低温压力容器用碳素钢板
低温圧力容器用炭素鋼鋼板 Carbon steel plates for pressure
vessels for low temperature service
JIS G3127-2005 低温设备压力容器用镍钢板
低温圧力容器用ニッケル鋼鋼板 Nickel steel plates for pressure
vessels for low temperature services
JIS G3202-1988 压力容器用碳素钢锻件
圧力容器用炭素鋼鍛鋼品 Carbon steel forgings for pressure
vessels
JIS G3203-1988 高温压力容器用合金钢锻件
高温圧力容器用合金鋼鍛鋼品 Alloy steel forgings for pressure
vessels for high-temperature service
JIS G3204-1988 压力容器用淬火和回火的合金钢锻件
圧力容器用調質型合金鋼鍛鋼品 Quenched and tempered alloy steel
forgings for pressure vessels
JIS G3205-1988 低温压力容器用碳素钢及合金钢锻件
低温圧力容器用鍛鋼品 Carbon and alloy steel forgings for
pressure vessels for low-temperature service
JIS G3206-1993 高温下压力容器用高强度铬-钼合金钢锻件
高温圧力容器用高強度クロムモリブデン鋼鍛鋼品 High strength chromium-molybdenum
alloy steel forgings for pressure vessels under
high-temperature service
JIS G3214-1991 压力容器用不锈钢锻件
圧力容器用ステンレス鋼鍛鋼品 Stainless steel forgings for
pressure vessels
JIS G3454-2007 压力设备用碳钢管
圧力配管用炭素鋼鋼管 Carbon steel pipes for pressure service
JIS G4109-2008 锅炉和压力容器用铬钼合金钢板
ボイラ及び圧力容器用クロムモリブデン鋼鋼板 Chromium-molybdenum alloy
steel plates for boilers and pressure vessels
JIS G4110-2004 高温下压力容器用高强度铬钼和铬钼钒合金钢板
高温圧力容器用高強度クロムモリブデン鋼及びクロムモリブデンバナジウム鋼鋼板 High strength
chromium-molybdenum and chromium-molybdenum-vanadium
alloy steel plates for pressure vessels under
high-temperature service
JIS H7201-2007 吸氢合金的压力-组成-温度(PCT)关系用测量方法
水素吸蔵合金の圧力―組成等温線（ＰＣＴ線）の測定方法 Method for measurement
of pressure-composition-temperature(PCT) relations
of hydrogen absorbing alloys
JIS K2258-1998 原油和石油产品.蒸发压力的测定.里德法
原油及び燃料油 ― 蒸気圧試験方法 ― リード法 Crude oil and petroleum
products -- Determination of vapour pressure
-- Reid method
JIS K5600-3-5-1999 涂料试验方法.第3部分:成膜性.第5节:堆叠性压力试验
塗料一般試験方法 ― 第３部：塗膜の形成機能 ― 第５節：耐圧着性 Testing methods
for paints -- Part 3: Film formability -- Section
5: Pressure test for stackability
JIS K7030-1997 玻璃纤维增强热固性塑料(GRP)制管道和配件.与压力相关的术语定义、包括术语之间的关系及安装和连接的术语
ガラス繊維強化プラスチック（ＧＲＰ）管及び継手 ― 圧力とその関係，施工並びに接合に関する用語の定義
Pipes and fittings made of glass fiber reinforced
thermosetting plastics (GRP) -- Definitions
of terms relating pressure, including relationships
between them, and terms for installation and
jointing
JIS P8131-2009 纸张和纸板.用马伦式高压力试验机测定产品脆裂强度
板紙―破裂強さ試験方法 Board -- Determination of bursting
strength
JIS R9301-3-4-1999 矾粉.第3部分:化学分析方法.第4节:压力容器中的酸性测定
アルミナ粉末 ― 第３部：化学分析方法 ― ４：加圧酸分解 Alumina powder
-- Part 3: Methods of chemical analysis -- 4:
Decomposition by acid in pressure vessel
JIS S2302-1994 汽水饮料瓶的抗内压力试验法
炭酸飲料用ガラスびんの耐内圧力試験方法 Method of internal pressure
test for carbonated beverage bottles
JIS S3200-1-1997 供水服务设备.静水压力的测试方法
水道用器具 ― 耐圧性能試験方法 Equipment for water supply
service -- Test methods of hydrostatic pressure
JIS S3200-5-1997 供水服务设备.用真空压力法破坏测试方法
水道用器具 ― 負圧破壊性能試験方法 Equipment for water supply
service -- Test methods of destruction by vacuum
pressure
JIS T3351-2007 压力监测用管设备
圧力モニタリング用チューブセット Tubing set for pressure monitoring
JIS T9111-6-2000 橡胶避孕套.第6部分:破裂容积和压力的测定
ラテックス製コンドーム ― 第６部：破裂容量及び破裂圧力の測定 Rubber condoms
-- Part 6: Determination of bursting volume
and pressure
JIS W0125-1-2000 航空航天.流体系统.词汇.第1部分:与压力有关的一般术语和定义
航空宇宙 ― 流体系統に関する用語 ― 第１部：圧力に関する一般用語及び定義 Aerospace
-- Fluid systems -- Vocabulary -- Part 1: General
terms and definitions relating to pressure
JIS W0814-2002 飞行器设备.机载设备的环境和工作条件.湿度、温度和压力试验
航空機用機器 ― 搭載用機器の環境及び作動条件 ― 湿度－温度－圧力試験 Aircraft
equipment -- Environmental and operating conditions
for airborne equipment -- Humidity, temperature
and pressure tests
JIS W1841-1994 航空航天.气动、压力补偿式变量传送泵.一般要求
航空宇宙 ― 圧力補償式可変容量形油圧ポンプ ― 一般要求事項 Aerospace --
Hydraulic, pressure compensated, variable delivery
pumps -- General requirements
JIS W2921-1993 航空航天.液压系统和部件.压力和温度分类
航空宇宙 ― 流体系統及び構成部品 ― 圧力及び温度分類 Aerospace -- Fluid
systems and components -- Pressure and temperature
classifications
JIS W3202-1993 飞行器.压力加油连接件
航空機 ― 燃料加圧補給接続部 Aircraft -- Pressure refuelling
connections
JIS W3211-1993 飞行器.压力加油连接
航空機 ― 加圧給油接続部 Aircraft -- Pressure re-oiling
connection
JIS Z2332-1993 用压力变化测量检测漏泄的试验方法
放置法による漏れ試験方法 Test method for leaks using the
pressure change measurement
JIS Z2342-2003 压力试验过程中压力容器的声波发射测试方法和试验结果的分类
圧力容器の耐圧試験などにおけるアコースティック?エミッション試験方法及び試験結果の等級分類方法
Methods for acoustic emission testing of pressure
vessels during pressure tests and classification
of test results
JIS Z3881-2009 气体压力焊接技术合格鉴定标准程序
鉄筋のガス圧接技術検定における試験方法及び判定基準 Standard qualification
procedure for gas pressure welding technique
of steel bars for concrete reinforcement
JIS Z8707-1992 压力式温度计和双金属温度计温度测量方法
充満式温度計及びバイメタル式温度計による温度測定方法 Method of temperature
measurement by filled-system thermometers and
bimetallic thermometers
JIS Z8751-1994 通过液体静压力压头差读取真空计的方法
液柱差を使う真空計による真空度測定方法 Reading methods of the vacuum
gauges by means of the head difference in the
hydrostatic pressure
JIS Z8817-2002 可燃粉尘的爆炸压力和压力上升速率的试验方法
可燃性粉じんの爆発圧力及び圧力上昇速度の測定方法 Test method for explosion
pressure and rate of pressure rise of combustible
dusts
法国压力标准(NF pressure standards)
--------------------------------------------------------------------------------
编号 中文名称 英文名称
NF A00-501-3-1991 铸件.订货和供应的一般技术条件.第3部分:通过重量压力和负压的铝合金及镁合金的铸件
(FOUNDRY PRODUCTS. GENERAL TECHNICAL CONDITIONS
FOR ORDERING AND SUPPLYING. PART 3 : GRAVITY,LOW
PRESSURE AND VACUUM CASTINGS OF ALUMINIUM ALLOYS
AND MAGNESIUM ALLOYS.)
NF A09-494-2001 无损检验.渗漏试验.压力变化方法 (Non-destructive
testing - Leak testing - Pressure change method.)
NF A32-055-1-1996 压力用途的钢铸件的交货技术条件.第1部分:概述 (Technical
delivery conditions for steel castings for pressure
purposes. Part 1 : general.)
NF A32-055-2-1996 压力用途的钢铸件的交货技术条件.第2部分:环境温度和高温下使用的钢种
(Technical delivery conditions for steel castings
for pressure purposes. Part 2 : steel grades
for use at room temperature and elevated temperatures.)
NF A32-055-3-1996 压力用途的钢铸件的交货技术条件.第3部分:室温下使用的钢种
(Technical delivery conditions for steel castings
for pressure purposes. Part 3 : steel grades
for use at low temperatures.)
NF A32-055-4-1996 压力用途的钢铸件的交货技术条件.第4部分:奥氏体和奥氏体-铁素体钢种
(Technical deliverry conditions for steel castings
for pressure purposes. Part 4 : austenitic and
austenitic-ferritic steel grades.)
NF A36-000-1979 结构钢和锅炉与压力容器用钢的焊接特性的推荐规范 (RECOMMENDATIONS
CONCERNING THE WELDABILITY OF STRUCTURAL STEEL
AND OF BOILER AND PRESSURE VESSELS STEEL.)
NF A36-205-1/A1-2003 压力容器用扁平钢轧材.第1部分:一般要求 (Flat
products made of steels for pressure purposes
- Part 1 : general requirements.)
NF A36-205-2-2003 压力容器用扁平钢轧材.第2部分:具有规定高温性能的非合金钢与合金钢
(Flat products made of steels for pressure purposes
- Part 2 : non-alloy and alloy steels with specified
elevated temperature properties.)
NF A36-205-3-2003 压力容器用扁平钢轧材.第3部分:经过正火处理的可焊细晶粒钢
(Flat products made of steels for pressure purposes
- Part 3 : weldable fine grain steels, normalized.)
NF A36-205-4-2003 压力容器用扁平钢轧材.第4部分:具有规定低温特性的镍合金钢
(Flat products made of steels for pressure purposes
- Part 4 : nickel alloy steels with specified
low temperature properties.)
NF A36-205-5-2003 压力容器用钢制扁平产品.第5部分:热机轧制的可焊接细粒钢
(Flat products made of steels for pressure purposes
- Part 5 : weldable fine grain steels, thermomechanically
rolled.)
NF A36-205-6-2003 压力容器用钢制扁平产品.第6部分:可焊接淬火和回火细粒钢
(Flat products made of steels for pressure purposes
- Part 6 : weldable fine grain steels, quenched
and tempered.)
NF A36-225-2000 压力容器用不锈钢棒 (Stainless steel bars
for pressure purposes.)
NF A36-226-2001 具有规定的高温特性的压力容器用热轧可焊接钢棒 (Hot
rolled weldable steel bars for pressure purposes
with specified elevated temperature properties.)
NF A36-601-1980 锅炉和压力容器用可焊钢制锻件.碳钢和碳锰钢.质量等级和类型
(WELDED STEEL FORGINGS FOR BOILERS AND PRESSURE
VESSELS. CARBON AND CARBON MANGANESE STEELS.
GRADES AND TYPES.)
NF A36-602-1988 锅炉和压力容器用可焊钢制锻件.钼、锰钼和铬钼合金钢.质量等级和类型
(WELDABLE STEEL FORGINGS FOR BOILERS AND PRESSURE
VESSELS. MO,MN-MO AND CR-MO ALLOY STEELS. GRADES
AND TYPES.)
NF A36-603-1988 锅炉和压力容器用可焊钢制锻件.高屈服强度钢.质量等级和类型
(WELDABLE STEEL FORGINGS FOR BOILERS AND PRESSURE
VESSELS. HIGH YIELD STRENGTH ALLOY STEELS. GRADES
AND TYPES.)
NF A36-605-1982 锅炉和压力容器用焊接钢冲压锻件.碳钢和碳锰钢.牌号与型号
(Weldable steel drip forged articles for boilers
and pressure vessels. Carbon and carbon-manganese
steels. Grades and types .)
NF A36-606-1982 锅炉和压力容器用焊接钢冲压锻件.钼、锰钼和铬钼合金钢.牌号和型号
(Weldable steel drop forged articles for boilers
and pressure vessels. Mo, Mn/Mo and Cr/Mo alloy
steels. Grades and types.)
NF A36-607-1984 锅炉和压力容器用自由锻造或模锻法制奥氏体不锈钢零件.质量等级和类型
(AUSTENITIC STAINLESS STEEL PARTS OBTAINED BY
FLAT DIE FORGING OR DROP FORGING FOR BOILERS
AND PRESSURE VESSELS. GRADE AND TYPES.)
NF A36-620-1-1998 压力设备用钢锻件.第1部分:自由锻的一般要求(欧洲标准EN
10222-1) (STEEL FORGINGS FOR PRESSURE PURPOSES.
PART 1 : GENERAL REQUIREMENTS FOR OPEN DIE FORGINGS.
(EUROPEAN STANDARD EN 10222-1).)
NF A36-620-1/A1-2002 压力容器用钢锻件.第1部分:敞口铸模锻件的一般要求
(Steel forgings for pressure purposes - Part
1 : general requirements for open die forgings.)
NF A48-830-1983 铸制产品.有压力的饮用水聚氯乙烯管道用球墨铸铁接头 (Foundry
products. Spheroidal graphite cast iron sittings
for PVC drinking water pipes under pressure.)
NF A48-851-1985 铸造产品.压力管道用球墨铸铁管.聚氨酯涂层 (FOUNDRY
PRODUCTS. DUCTILE IRON PIPES FOR PRESSURE PIPELINES.
POLYURETHAN EXTERNAL COATING.)
NF A48-902-1985 铸造产品.压力管道用球墨铸铁管.离心水泥砂浆内饰面.新涂覆砂浆成分的控制
(Foundry products. Ductile iron pipes for pressure
pipelines. Contrifugal cement mortar internal
lining. Composition controls of freshly applied
mortar.)
NF A49-192-1981 钢管.压力容器用内螺纹非合金钢焊接套管 (STEEL TUBES.
WELDED RINGS,INTERNALLY THREADED,FOR PRESSURE
EQUIPMENT.)
NF A49-200-1-2002 无缝压力钢管.交货技术条件.第1部分:规定室温特性的非合金钢管
(Seamless steel tubes for pressure purposes
- Technical delivery conditions - Part 1 : non-alloy
steel tubes with specified room temperature
properties.)
NF A49-200-2-2002 无缝压力钢管.交货技术条件.第2部分:规定高温特性的非合金和合金钢管
(Seamless steel tubes for pressure purposes
- Technical delivery conditions - Part 2 : non-alloy
and alloy steel tubes with specified elevated
temperature properties.)
NF A49-200-3-2002 无缝压力钢管.交货技术条件.第3部分:合金细晶粒结构钢管
(Seamless steel tubes for pressure purposes
- Technical delivery conditions - Part 3 : alloy
fine grain steel tubes.)
NF A49-200-4-2002 无缝压力钢管.交货技术条件.第4部分:规定低温特性的合金和非合金钢管
(Seamless steel tubes for pressure purposes
- Technical delivery conditions - Part 4 : non-alloy
and alloy steel tubes with specified low temperature
properties.)
NF A49-201-1-2002 焊接压力钢管.交货技术条件.第1部分:规定室温特性的非合金钢管
(Welded steel tubes for pressure purposes -
Technical delivery conditions - Part 1 : non-alloy
steel tubes with specified room temperature
properties.)
NF A49-201-2-2002 焊接压力钢管.交货技术条件.第2部分:规定高温特性的电焊合金和非合金钢管
(Welded steel tubes for pressure purposes -
Technical delivery conditions - Part 2 : electric
welded non-alloy and alloy steel tubes with
specified elevated temperature properties.)
NF A49-201-3-2002 焊接压力钢管.交货技术条件.第3部分:合金细晶粒结构钢管
(Welded steel tubes for pressure purposes -
Technical delivery conditions - Part 3 : alloy
fine grain steel tubes.)
NF A49-201-4-2002 焊接压力钢管.交货技术条件.第4部分:规定低温特性的电焊非合钢管
(Welded steel tubes for pressure purposes -
Technical delivery conditions - Part 4 : electric
welded non-alloy steel tubes with specified
low temperature properties.)
NF A49-201-5-2002 焊接压力钢管.交货技术条件.第5部分:规定高温特性的埋弧焊接非合金和合金钢管
(Welded steel tubes for pressure purposes -
Technical delivery conditions - Part 5 : submerged
arc welded non-alloy and alloy steel tubes with
specified elevated temperature properties.)
NF A49-201-6-2002 焊接压力钢管.交货技术条件.第6部分:规定低温特性的埋弧焊接非合金钢管
(Welded steel tubes for pressure purposes -
Technical delivery conditions - Part 6 : submerged
arc welded non-alloy steel tubes with specified
low temperature properties.)
NF A49-244-1993 钢管.压力设备用焊接奥氏体不锈钢和奥氏铁素体轧制钢管的尺寸和技术交货条件
(STEEL TUBES. WELDED AUSTENITIC STAINLESS AND
AUSTENITIC FERRITIC STEEL ROLLED TUBES FOR PRESSURE
SERVICE. DIMENSIONS, TECHNICAL CONDITIONS FOR
DELIVERY.)
NF A49-900-1992 压力容器.无缝钢气瓶.钢的类型.半成品 (PRESSURE
VESSELS. SEAMLESS STEEL GAS VESSELS. TYPES OF
STEELS. SEMI FINISHED PRODUCTS.)
NF A50-120-2000 铝和铝合金.锻造产品.生产压力器件的产品的特殊要求 (Aluminium
and aluminium alloys - Wrought products - Special
requirements for products intended for the production
of pressure equipment.)
NF A51-202-1998 铜和合金铜.煮水器,压力容器和热水贮存器用的盘状,片状,带状,和环状铜和铜合金
(Copper and copper alloys. Plate, sheet and
circles for boilers, pressure vessels and hot
water storage units.)
NF A51-202/A1-2000 铜和合金铜.煮水器、压力容器和热水贮存器用的板状、片状和环状铜和铜合金
(Copper and copper alloys - Plate, sheet and
circles for boilers, pressure vessels, and hot
water storage units.)
NF A66-002-1985 铸造产品.铝合金和锌合金.压力铸件的尺寸公差 (Foundry
products. Aluminium alloys and zinc alloys.
Cast products. Dimensional tolerances for pressure
die castings.)
NF A84-410-2003 气焊设备.焊接、切割和相关工艺中使用的压力计 (Gas
welding equipment - Pressure gauges used in
welding, cutting and allied processes.)
NF A84-433-2001 气焊设备.小于等于300bar的焊接、切削及相关工艺用多头管系用压力调节器
(Gas welding equipment - Pressure regulators
for manifold systems used in welding, cutting
and allied processes up to 300 bar.)
NF A87-012-2-2000 焊接.钢的基本焊接接合详图.第2部分:非内部压力器件
(Welding - Basic weld joint details in steel
- Part 2 : non internal pressurized components.)
NF A89-011-1986 煤气或蒸气用钢压力器.焊接操作方式的鉴定.固定在横木顶杆或拉杆.竖杆壁上的连接情况
(STEEL VESSELS SUBJECT TO GAS OR STEAM PRESSURE.
QUALIFICATION OF A WELDING PROCEDURE. APPLICATION
TO THE WELDING OF TIE BARS,BRACES AND BOLTS
ON TO A WALL.)
NF A89-574-2003 金属材料焊接的无损检验.电阻焊接.电阻缝焊的压力试验 (Destructive
test on welds in metallic materials - Resistance
welding - Pressure test on resistance seam welds.)
NF A89-701-3-2003 CO2激光切割、焊接机的验收试验.第3部分:气体流量和压力测量仪的校准
(Acceptance tests for CO2-laser beam machines
for welding and cutting - Part 3 : calibration
of instruments for measurement of gas flow and
pressure.)
NF B34-005-1997 硅硼玻璃3.3制压力设备.设计、生产和试验的一般规则 (Pressure
equipment made from borosilicate glass 3.3.
General rules for design, manufacture and testing.)
NF B35-701-1962 实验室用玻璃器皿.电离压力表 (LABORATORY GLASSWARE.
IONISATION MANOMETERS.)
NF B43-305-2003 高级工业陶瓷.在大气压力下高温时陶瓷复合物的机械特性.挠曲强度的测定
(Advanced technical ceramics - Mechanical properties
of ceramic composites at high temperature under
air at atmospheric pressure - Determination
of flexural strength.)
NF B51-032-1981 层压胶合板.压力剪切试验 (LAMINATED BONDED
WOOD- TEST OF COMPRESSION SHEAR.)
NF B56-015-1980 纤维板.垂直于板面的压力试验 (WOOD WOOL SLABS.
MEASUREMENT OF TRANSVERSE COMPRESSION.)
NF B57-044-1973 软木.纯膨胀粘合体.恒压力下的变形 (Cork. Pure
expansed agglomerates. Deformation under constant
pressure.)
NF C23-516-1998 防爆电气设备.压力装置P (Electrical apparatus
for potentially explosive atmospheres. Pressurized
apparatus “p“.)
NF C26-136-1-1998 电气用途的波纹状压力板和压力纸板.定义,标记和一般要求
(Corrugated pressboard and presspaper for electrical
purposes. Part 1 : definitions, designations
and general requirements.)
NF C26-148-1-1998 电气用压力敏感粘接带.第3部分:个体材料规范.第1节:带压力敏感粘接的PVC膜带
(Pressure-sensitive adhesive tapes for electrical
purposes. Part 3 : specifications for individual
materials. Sheet 1 : PVC film tapes with pressure-sensitive
adhesive.)
NF C26-148-3-1998 电气用压力敏感粘接带.第3部分:个体材料规范.第3节:带橡胶热固粘接的聚合物膜带
(Pressure-sensitive adhesive tapes for electrical
purposes. Part 3 : specifications for individual
materials. Sheet 3 : polyester film tapes rubber
thermoplastic adhesive.)
NF C26-148-4-1998 电气用压力敏感粘接带.第3部分:个体材料规范.第4节:带橡胶热塑粘接的,皱折的,纤维素纸
(Pressure-sensitive adhesive tapes for electrical
purposes. Part 3 : specifications for individual
materials. Sheet 4 : cellulosic paper, creped,
with rubber thermosetting adhesive.)
NF C26-148-5-1998 电气用压力敏感粘接带.第3部分:个体材料规范.第5节:带橡胶热塑粘接的,非皱折的,纤维素纸
(Pressure-sensitive adhesive tapes for electrical
purposes. Part 3 : specifications for individual
materials. Sheet 5 : cellulosic paper, non creped,
with rubber thermosetting adhesive.)
NF C26-148-6-1998 电气用压力敏感粘接带.第3部分:个体材料规范.第6节:带丙烯酸树脂热塑粘接的多聚碳膜
(Pressure-sensitive adhesive tapes for electrical
purposes. Part 3 : specifications for individual
materials. Sheet 6 : polycarbonate film tapes
with acrylic thermoplastic adhesive.)
NF C32-029-1996 电缆绝缘和护套材料通用试验方法.第3部分:聚氯乙烯专用方法.第1节:高温下压力试验.耐裂性试验
(Insulating and sheathing materials of electric
cables. Common test methods. Part 3 : methods
specific to PVC compounds. Section 1 : pressure
test at high temperature. Tests for resistance
to cracking.)
NF C52-216-5-2002 电力变压器和反应堆配件.第5部分: 液位计、压力装置和流量指示器
(Power transformer and reactor fittings - Part
5 : liquid level, pressure devices and flow
indicators.)
NF C52-216-5/A1-2003 电力变压器和电抗器的配件.第5部分:液位计、压力器具和流量指示器
(Power transformer and reactor fittings - Part
5 : liquid level, pressure devices and flow
indicators.)
NF C54-101-1987 并联电容器的内部熔断器和内部过压力隔离器 (Internal
fuses and internal overpressure disconnectors
for shunt capacitors.)
NF C64-4511-1993 置于气体压力下的高压装置用铝和铝合金煅制外壳.(欧洲标准
EN 50064).补充件1 ()
NF C93-537-3-15-2003 通信电缆.试验方法规范.第3-15部分:机械试验方法.耐静水压力的水下电缆
(Communication cables - Specifications for test
methods - Part 3-15 : mechanical test methods
- Underwater cable resistance to hydrostatic
pressure.)
NF C93-902-11-1997 纤维光学连接装置和无源元件.基本检验和测量程序.第2-11部分:试验.轴向压力
(Fibre optic interconnecting devices and passive
components. Basic test and measurement procedures.
Part 2-11 : tests. Axial compression.)
NF C93-902-23-1997 光学纤维互联元件和无源元件.基本试验和测量过程.第2-23部分:试验.纤维光学装置非压力封闭密封
(Fibre optic interconnecting devices and passive
components. Basic test and measurement procedures.
Part 2-23 : tests. Sealing for non-pressurized
closures of fibre optic devices.)
NF C93-903-22-1997 光学纤维互联元件和无源元件.基本试验和测量过程.第3-22部分:检验和测量.金属箍压力
(Fibre optic interconnecting devices and passive
components. Basic test and measurement procedures.
Part 3-22 : examinations and measurements. Ferrule
compression force.)
NF C97-332-1994 传声器的测量.第2部分:用可逆技术对实验室标准传声器压力校正的基本方法
(Measurement microphones. Part 2 : primary method
for pressure calibration of laboratory standard
microphones by the reciprocity technique.)
NF C97-335-2003 测量传声器.第5部分:用对比法进行标准工作传声器压力校准
(Measurement microphones - Part 5 : methods
for pressure calibration of working standard
microphones by comparison.)
NF D18-216-2003 卫生洁具.压力冲洗阀和小便池自动关闭阀PN10 (Sanitary
tapware - Pressure flushing valves and automatic
closing urinal valves PN 10.)
NF D21-351-1982 快速压力蒸煮器 (Appliances for high-speed
pressure-cooking.)
NF D21-351-2003 烹饪器具.家用压力锅 (Cookwares - Pressure
cookers for domestic use.)
NF D30-500-2003 试验气体.试验压力.仪器种类 (Test gases -
Test pressures - Appliance categories.)
NF D30-500/A1-1997 试验气体.试验压力.仪器种类.修改件1 (Test
gases - Test pressures - Appliances categories.)
NF D35-356-1998 专用液化石油气器具规范.便携式蒸气压力液化石油气装置 (Specifications
for dedicated liquefied petroleum gas appliances.
Portable vapour pressure liquefied petroleum
gas appliances.)
NF D36-202-1991 制作200mbar以下压力家用燃气设备用动态密封垫圈的匀质橡胶材料.(欧洲标准
EN 279) (Homogeneous rubber materials for dynamic
seals in domestic appliances using combustible
gases up to 200 mbar.)
NF D36-203-1991 制作200mbar以下压力家用燃气设备用膜片的橡胶材料.(欧洲标准
EN 278) (RUBBER MATERIALS FOR DIAPHRAGMS IN
DOMESTIC APPLIANCES USING COMBUSTIBLE GASES
UP TO 200 MBAR. (EUROPEAN STANDARD EN 278).)
NF D36-403-2000 建筑阀门.压力安全阀.试验和要求 (Building valves
- Pressure safety valves - Tests and requirements.)
NF D36-404-2000 建筑阀门.温度和压力组合安全阀.试验和要求 (Building
valves - Combined temperature and pressure relief
valves - Tests and requirements.)
NF D38-341-1996 家用无霜制冷设备.制冷机、制冷机冷藏柜、冷冻食品储藏柜和用内压力空气循环冷却的食品冷藏柜特性和试验方
(HOUSEHOLD FROST-FREE REFRIGERATING APPLIANCES.
REFREIGERATORS, REFRIGERATOR-FREEZERS, FROZEN
FOOD STORAGE CABINETS AND FOOD FREEZERS COOLED
BY INTERNAL FORCED AIR CIRCULATION. CHARACTERISTICS
AND TEST METHODS. (EUROPEAN STANDARD EN ISO
8561).)
NF E01-200-1994 压力设备.压力/温度/体积术语 (Pressure equipment.
Terminology and symbols. Pressure, temperature,
volume.)
NF E01-201-2-2002 压力设备.第2部分:质量、符号和单位 (Pressure
equipment - Part 2 : quantities, symbols and
units.)
NF E01-201-3-2002 压力设备.第3部分:定义和有关方面 (Pressure
equipment - Part 3 : definition and parties
involved.)
NF E01-201-4-2003 压力设备.金属材料的技术交货条件的确立 (Pressure
equipment - Part 4 : establishment of technical
delivery conditions for metallic materials.)
NF E01-201-5-2003 压力设备.第5部分:材料合格和检验用文件 (Pressure
equipment - Part 5 : compliance and inspection
documentation of materials.)
NF E01-201-7-2002 压力设备.第7部分:不用火加热的压力设备的安全系统
(Pressure equipment - Part 7 : safety systems
for unfired pressure equipment.)
NF E03-005-1-2003 非压力密封连接的管螺纹 第1部分:标记、尺寸和公差
(Pipe threads where pressure-tight joints are
not made on the threads - Part 1 : dimensions,
tolerances and designation.)
NF E15-024-1968 检验压力量规的固定装置(陆地使用的规定要求) (FIXING
DEVICE FOR CHECK PRESSURE GAUGES (STATUTORY
REQUIREMENTS FOR EARTH USE).)
NF E15-028-1994 压力计词汇 (Pressure gauges. Vocabulary.)
NF E15-034-2000 工业压力计.金属指示压力计.差压计 (Industrial
pressure gauges - Metallic pressure gauge indicators
- Differential gauges.)
NF E15-038-1989 工业压力表.金属指示压力表.绝对压力计 (INDUSTRIAL
PRESSURE GAUGES. METALLIC PRESSURE GAUGE INDICATORS.
ABSOLUTE PRESSURE GAUGES.)
NF E15-039-1-1997 压力计.第1部分:低音管压力计.尺寸、度量衡、要求和试验(欧洲标准EN
837-1) (Pressure gauges. Part 1 : Bourdon tube
pressure gauges. Dimensions, metrology, requirements
and testing.)
NF E15-100-2000 工业压力计和温度计.金属指示压力计和温度计.带控制功能的压力计和温度计
(Industrial pressure gauges and thermometers
- Metallic indicator pressure gauges and thermometers
- Pressure gauges and thermometers with control
function.)
NF E22-144-1987 边缘定心直齿圆柱渐开线花键.压力角３０，３７５和４５°.总则和尺寸
(Straight cylindrical involute splines. Side
fit. Pressure angles 30 degrees, 37,5 degrees
and 45 degrees.)
NF E29-000-1996 管件.标准压力的定义和选择(欧洲标准EN 1333) (Pipework
components. Definition and selection of pn.)
NF E29-008-1972 管道.压力和温度.２３％镍和４％锰奥氏体球墨合金铸铁部件
(TEMPERATURE AND PRESSURE LIMITATIONS FOR PIPING
SYSTEMS MANUFACTURED FROM 23% NICKEL 4% MANGANESE
SPHEROIDAL GRAPHITE AUSTENITIC CAST IRON`.)
NF E29-009-1972 管道.压力和温度.２０％镍和２％铬奥氏体球墨合金铸铁部件
(TEMPERATURE AND PRESSURE LIMITATIONS FOR PIPING
SYSTEMS MANUFACTURED FROM 20% NICKEL 2% CHROMIUM
SPHEROIDAL GRAPHITE AUSTENITIC CAST IRON`.)
NF E29-018-1986 工业管道.凹面或凸面连接的法兰盘连接环.ＩＳＯ标准压力为２．５到５０
(Industrial pipework. Bracing rings for flanges
with female (groove or spigot), or male(tongue
or spigot) faces. ISO PN 2,5 to ISO PN 50.)
NF E29-043-1990 工业管道工程.管道、锅炉和压力容器法兰组件用非合金钢或合金钢制螺栓
(Industrial pipework. Non alloy and alloy. Steel
bolting for flanged assemblies of pipeworks,
boilers and pressure vessels. Specifications.)
NF E29-161-1943 支流阀.关闭阀和给水阀.总则.公称压力.标准压力１０ (BRANCH
PIPE VALVES. STOPCOCKS AND DRAW-OFF COCKS. GENERAL.
NOMINAL PRESSURE PN 10.)
NF E29-162-1943 支流阀.关闭阀.公称压力，标准压力１０ (BRANCH
PIPE VALVES. STOPCOCKS. NOMINAL PRESSURE PN
10.)
NF E29-163-1943 支流阀.给水阀.公称压力，标准压力１０ (BRANCH
PIPE VALVES. DRAW-OFF COCKS. NOMINAL PRESSURE
PN 10.)
NF E29-171-1999 入口压力最大达100bar的气压调节器 (Gas pressure
regulators for inlet pressures up to 100 bar.)
NF E29-171/A1-2001 入口压力100巴以下的气体压力调节器 (Gas pressure
regulators for inlet pressures up to 100 bar.)
NF E29-175-2003 气体压力调节站和装置用安全设备.用于入口压力最高达100bar的气体安全关闭装置
(Safety devices for gas pressure regulating
stations and installations - Gas safety shut-off
devices for inlet pressures up to 100 bar.)
NF E29-179-2002 入口压力达100巴的压力调节器和相关安全装置用弹性体 (Elastomers
for gas pressure regulators and associated safety
devices for inlet pressures up to 100 bar.)
NF E29-210-1985 工业管道.差动压力装置用有孔法兰 (INDUSTRIAL
PIPEWORK. ORIFICE FLANGES FOR DIFFERENTIAL PRESSURE
DEVICES.)
NF E29-251-1972 工业管道.不锈钢制焊接冲压凸缘（薄型系列）.公称压力１０
(STAMPED STAINLESS-STEEL FILLETS FOR WELDING
(THIN SERIES) PN 10)
NF E29-311-1-2003 工业阀门.阀门试验.第1部分:压力试验、试验程序和验收标准.强制性要求
(Industrial valves - Testing of valves - Part
1 : pressure tests, test procedures and acceptance
criteria - Mandatory requirements.)
NF E29-311-1982 阀门.阀门制造设备的工厂压力试验 (Valves. Factory
pressure testing for valves.)
NF E29-319-2003 最大工作压力为16bar及以下的配气系统用阀.性能要求
(Valves for gas distribution systems with maximum
operating pressure less than or equal 16 bar
- Performance requirements.)
NF E29-373-1984 工业阀门.止回阀.钢制，单摇板式，带法兰盘,ISO标准压力16，20，25，40，50，100
(Industrial valves. Flanged steel swing check
valves. ISO PN A6, ISO PN 20, ISO PN 25, ISO
PN 40, ISO PN 50, ISO PN 100.)
NF E29-531-1981 管道.凸肩对接的螺纹连接管.标准压力10 (Pipework.
Threaded fittings with gasket on shoulder.)
NF E29-539-1981 管道.采暖设备上的球锥连接螺纹连接管部件.标准压力16
(Pipework. Screwed connecting part with a spheroconical
function for heating plants.)
NF E29-572-1969 对称半边连接管(吉耶曼系统).公称压力16 (QUARTER
TURN CONNECTIONS (GUILLEMIN SYSTEM). NOMINAL
PRESSURE PN 16.)
NF E29-573-1988 工业管道.“特快“连接管，公称压力”10 (Industrial
pipework. “Express“ connections. Maximum permissible
working pressure 1 MPa (10 bar).)
NF E29-661-1979 氯瓶上的锻钢阀门(最大容量60kg).公称压力25 (FORGED-STEEL
VALVES FOR CHLORINE CYLINDERS (MAX.CAPACITT
60 KG). NOMINAL PRESSURE PN 25.)
NF E29-662-1979 呼吸保护装置的压缩气瓶的阀门.使用压力200bar.尺寸特性.标记
(VALVES FOR COMPRESSED AIR CYLINDERS FOR RESPIRATORY
PROTECTIVE EQUIPMENT. SERVICE PRESSURE 200 BAR.
DIMENSIONAL CHARACTERISTICS. MARKING.)
NF E29-663-1979 呼吸保护装置的压缩气瓶的阀门.使用压力300bar.尺寸特性.标记
(VALUES FOR COMPRESSED AIR CYLINDERS FOR RESPIRATORY
PROTECTIVE EQUIPMENT. SERVICE PRESSURE 300 BAR.
DIMENSIONAL CHARACTER & STICS. MARKING.)
NF E29-760-1988 气瓶.压缩气.液化气或熔解气气瓶的反复压力试验 (GAS
CYLINDERS. FATIGUE STRENGTH TESTING UNDER REPEATED
PRESSURIZING FOR LIQUEFIED OR DISSOLVED COMPRESSED
GASES.)
NF E31-354-1-1999 供暖锅炉.第1部分:压力送风喷嘴式供暖锅炉.术语、一般要求、试验和标志
(Heating boilers. Part 1 : heating boilers with
forced draught burners. Terminology, general
requirements, testing and marking.)
NF E31-354-4-1999 采暖锅炉.第4部分:有强制通风式燃烧器的采暖锅炉.功率70kW以下、最大工作压力3巴的有强制通风式燃烧器的采
()
NF E31-513-1998 不超过300KW的热输入的空间加热器用非家用燃气压力对流空气加热热水器,与风扇辅助的可燃空气和/或可燃产品
(NON-DOMESTIC GAS-FIRED FORCED CONVECTION AIR
HEATERS FOR SPACE HEATING NOT EXCEEDING A NET
HEAT INPUT OF 300 KW, INCORPORATING AN FAN TO
ASSIST TRANSPORTATION OF COMBUSTION AIR AND/OR
COMBUSTION PRODUCTS. (EUROPEAN STANDARD EN 1020).)
NF E31-520-1998 专用液化石油器用具的规范.可移动式和可携带式非家用压力对流传热的直接点火空气燃烧器
(SPECIFICATION FOR DEDICATED LIQUEFIED PETROLEUM
GAS APPLIANCES. MOBILE AND PORTABLE NON-DOMESTIC
FORCED CONVECTION DIRECT FIRED AIR HEATERS.
(EUROPEAN STANDARD EN 1596).)
NF E32-110-2-2002 水管锅炉和辅助设备.第2部分:锅炉和附件的压力零件用材料
(Water-tube boilers and auxiliary installations
- Part 2 : materials for pressure parts of boilers
and accessories.)
NF E32-110-3-2002 水管式锅炉和辅助设备.第3部分:压力部件的设计和计算
(Water-tube boilers and auxiliary installations
- Part 3 : design and calculation for pressure
parts.)
NF E32-110-5-2002 水管锅炉和辅助设备.第5部分:锅炉的压力部件的工艺和结构
(Water tube boilers and auxiliary installations
- Part 5 : workmanshhip and construction of
pressure parts of the boilers.)
NF E32-115-2-2002 壳体锅炉.第2部分:锅炉和附件的压力部件材料 (Shell
boilers - Part 2 : materials for pressure parts
of boilers and accessories.)
NF E32-115-3-2002 火管锅炉.第3部分:锅炉的压力部件的设计和计算 (Shell
boilers - Part 3 : design and calculation for
pressure parts.)
NF E32-115-4-2002 火管锅炉.第4部分:锅炉压力部件的工艺和结构 (Shell
boilers - Part 4 : workmanship and construction
of pressure parts of the boiler.)
NF E32-115-5-2002 火管锅炉.第5部分:锅炉压力部件制造、文献工作和标志过程的检测
(Shell boilers - Part 5 : inspection during
construction, documentation and marking of pressure
parts of the boiler.)
NF E35-407-2002 制冷系统和热泵.限制压力的安全开关装置.要求和试验 (Refrigerating
systems and heat pumps - Safety switching devices
for limiting the pressure - Requirements and
tests.)
NF E37-406-1988 内燃机用全流量润滑油滤器的试验方法.第6部分:静态破裂压力试验
(Methods of test for full-flow lubricating oil
filters for internal combustion engines. Part
6 : static burst pressure test.)
NF E48-055-1-2003 液压传动.带分离式或一体式法兰夹和米制或英制螺纹的凸缘联接器.第1部分:压力为3.5MPa至35MPa(35bar至350ba
(Hydraulic fluid power - Flange connectors with
split or one-piece flange clamps and metric
or inch screws - Part 1 : flange connectors
for use at pressures of 3,5 MPa (35 bar) to
35 MPa (350 bar), DN)
NF E48-055-1986 液压传动.法兰盘和银插入凸缘的矩形法兰和装置，公称压力250和400.尺寸
(Hydraulic fluid power. Rectangular flanges
with recessed flange head. PN 250 and PN 400.
Dimensions.)
NF E48-055-2-2003 液压传动.带分离式或一体式法兰夹和米制或英制螺纹的凸缘联接器.第2部分:压力为35MPa至40MPa(350bar至400ba
(Hydraulic fluid power - Flange connectors with
split or one-piece flange clamps and metric
or inch screws - Part 2 : flange connectors
for use at pressures of 35 MPa (350 bar) to
40 MPa (400 bar), DN)
NF E48-056-2001 液压动力.在压力为20MPa(200bar)至压力为31,5MPa(315bar)使用的面对流型,快反应耦合型
(Hydraulic fluid power - Flush-face type, quick-action
couplings for use at pressures of 20 MPa (200
bar) to 31,5 MPa (315 bar) - Specifications.)
NF E48-057-1-2001 液压动力和一般用连接件.诊断用途的液压耦合件.第1部分:非压力连接耦合
(Connections for fluid power and general use
- Hydraulic couplings for diagnostic purposes
- Part 1 : coupling not for connection under
pressure.)
NF E48-057-2-2001 液压动力和一般用连接件.诊断用途的液压耦合件.第2部分:压力连接的M16X2末端的耦合
(Connections for fluid power and general use
- Hydraulic couplings for diagnostic purposes
- Part 2 : coupling with M16 X 2 end for connection
under pressure.)
NF E48-100-2000 液压传动系统和元件.标称压力 (Fluid power
systems and components - Nominal pressures.)
NF E48-151-2000 液压传动.带分离器的气压蓄能器.压力和容量范围、性能数据
(Hydraulic fluid power - Gas-loaded accumulators
with separator - Ranges of pressures and volumes
and characteristic quantities.)
NF E48-381-2002 液压传动.马达特性的测定.第1部分:在恒低速和恒压力下的测定
(Hydraulic fluid power - Determination of characteristics
of motors - Part 1 : at constant low speed and
constant pressure.)
NF E48-390-1997 液压传动.在系统和元件中对产生压力波动等级的测定.第1部分:泵精确度法
(HYDRAULIC FLUID POWER. DETERMINATION OF PRESSURE
RIPPLE LEVELS GENERATED IN SYSTEMS AND COMPONENTS.
PART 1 : PRECISION METHOD FOR PUMP.)
NF E48-391-2000 液压动力.系统和元件内产生的压力波动水平的测定.泵用简化方法
(Hydraulic fluid power - Determination of pressure
ripple levels generated in systems and components
- Simplified method for pumps.)
NF E48-393-2001 液力传动.系统和元件中产生的压力波动等级的测定.第3部分:电动机法
(Hydraulic fluid power - Determination of pressure
ripple levels generated in systems and components
- Part 3 : method for motors.)
NF E48-613-1973 液压传动用流体.D级难燃流体蒸汽压力的测定 (FLUIDS
FOR HYDRAULIC POWER SYSTEMS-DETERMINATION OF
VAPOUR PRESSUREOF FIRE-RESISTANT FLUIDS,FORM
D)
NF E48-678-1995 液压传动.接收器口及压力输送用过滤器.性能 (Hydraulic
fluid power. Filters for receiver venting and
pressurization. Performances.)
NF E48-701-1993 液压传动.滤油器.定义、标定压力、标定尺寸、配件尺寸 (Hydraulic
fluid power. Filters. Definitions, nominal pressures,
nominal sizes, fitting dimensions.)
NF E63-001-1994 鹅颈管底座机械压力机.词汇 (Open front mechanical
power presses. Vocabulary.)
NF E63-002-1996 前开式机械动力压力机的验收条件.最大允许功率的测定和尺寸
(Open front mechanical power presses. Capacity
ratings and dimensions.)
NF E63-003-1986 材料变形加工机械.鹅颈管底座机械压力机验收条件.精确度检验
(Material forming machines. Acceptance conditions
of open front mechanical power presses. Accuracy
testing.)
NF E63-006-1986 材料变形加工机械.压力机.两种语言术语:法语和英语 (MATERIAL
FORMING MACHINES. PRESSES. BILINGUAL ENGLISH-FRENCH.)
NF E63-015-1982 冲压机询件、报价和订购格式.螺旋压力机 (Form for
enquiry, quoting and ordering of drop forging
plant. Screw presses.)
NF E63-017-1985 材料变形加工机械.金属冷加工用拱式及鹅颈管机械压力机询价，报价和订购格式
(MACHINES FOR METAL FORMING. FORM FOR CONSULTATION,ENQUIRY
AND ORDERING OF OPEN-FRONT AND STRAIGHT-SIDED
MECHANICAL PRESSES FOR COLD WORKING OF METALS.)
NF E63-020-1998 机械压力.安全 (Mechanical presses
- Safety.)
NF E63-023-2003 机床的安全.气动压力机 (Safety of machine
tools - Pneumatic presses.)
NF E63-031-1993 机床.标称压力400kn以上包括4000kn的直边单动机械压力机.特性和尺寸
(Machine-tools. Straight-sided single action
mechanical power presses from 400 kn up to and
including 4 000 kn nominal force. Characteristics
and dimensions.)
NF E63-032-1993 机床.标称压力250kn以上包括4000kn的直边高速机械压力机.特性和尺寸
(Machine-tools. Straight sided high speed mechanical
power presses from 250 kn up to and including
4 000 nominal force. Characteristics and dimensions.)
NF E63-052-1968 压力机配套工具.柱上的环形件 (PRESS TOOLS.
PILLAR KEEPER RING.)
NF E63-053-1974 压力机配套工具.中间定位柱的法兰盘 (PRESS TOOLS.FLANGE
FOR MIDDLE LOCATING PILLAR.)
NF E63-054-1974 压力机配套工具.连接导环 (PRESS TOOLS.PILLAR
GUIDE BUSH.)
NF E63-055-1974 压力机配套工具.安装在底座上的连接导环 (PRESS TOOLS.PILLAR
GUIDE BUSH FOR MOUNTING IN BOLSTER.)
NF E63-056-1974 压力机配套工具.密封导环 (PRESS TOOLS.FIXED
GUIDE BUSH.)
NF E63-057-1974 压力机配套工具.连接环的止动法兰盘 (PRESS TOOLS.RETAINING
FLANGE FOR GUIDE BUSH.)
NF E63-076-1974 压力机配套工具.导向部件.自动润滑油环 (PRESS TOOLS
- GUIDING ELEMENTS - SELF-OILING RINGS.)
NF E63-081-1984 压力机配套工具.各种型孔模型 (PRESS TOOLS.
DIES FOR SHAPE HOLES.)
NF E63-090-1998 压力工具.压实件 (TOOLS FOR PRESSING.
DIE SETS.)
NF E63-101-1973 压力机配套工具.有凸缘的阳模凹座 (PRESS TOOLS-COLLAR
PUNCH HOUSINGS.)
NF E63-109-1984 压力机配套工具.６０°锥形头冲切模 (Press tools.
Punches with 60 degrees conical head.)
NF E63-116-2001 压力机.球形闸门凸模固定板.第2部分:小功率用C和D型
(Tools for pressing - Ball-lock punch retainers
- Part 2 : types C and D, reduced for light
duty.)
NF E63-119-1984 压力机配套工具.阳模.定义.阳模的主要型号.术语 (PRESS
TOOLS. PUNCHES. DEFINITIONS OF PRINCIPAL TYPES
OF PUNCH. TERMINOLOGY.)
NF E63-120-1976 压力机配套工具.滚珠导套.滚珠导套的安装 (PRESS
TOOLS. BALL GUIDES. BALL GUIDE MOUNTING.)
NF E63-123-1983 压力机配套工具.滚珠导套和滑动导套.凸缘肩轴衬和螺纹凸肩环
(Press tools. Guide bushing. Shouldered clamping
and shouldered threaded bushes.)
NF E63-124-1976 压力机配套工具.滚珠导套.滚珠轴承隔离套 (PRESS
TOOLS. BALL GUIDES. BALL CAGE.)
NF E63-125-1976 压力机配套工具.滚珠导套.配件 (PRESS TOOLS.
BALL GUIDES. ACCESSORIES.)
NF E63-131-2-1996 压力工具.气压弹簧.第2部分:附属规范 (Tools
for pressing. Gas springs. Part 2 : specification
of accessories.)
NF E63-134-1992 压制工具.合成橡胶压力弹簧.第1部分:一般规范 (Tools
for pressing. Elastomer pressure springs. Part
1 : general specification.)
NF E63-135-1992 压制工具.合成橡胶压力弹簧.第2部分:附件的规范 (Tools
for pressing. Elastomer pressure springs. Part
2 : specification of accessories.)
NF E63-136-1992 压制工具.矩形截面压力弹簧.骨架尺寸和色彩编码 (Tools
for pressing. Compression springs with rectangular
section. Housing dimensions and colour coding.)
NF E63-141-1992 压力工具.弹簧拆卸器 (TOLLS FOR PRESSING.
SPRING EJECTOR.)
NF E63-502-1995 铸造和压力工具.机械薄板.第一部分:机械压力薄板.选矿器和固定物
(Tools for pressing and moulding. Machined plates.
Part 1 : machined plates for press tools, jigs
and fixtures.)
NF E64-102-1984 木材加工机械.框形设计压力机.术语 (WOODWORKING
MACHINES. NOMENCLATURE FOR FRAME CLAMPS.)
NF E82-002-1-1999 钢热模锻件.尺寸公差.第1部分:落锤锻造和垂直压力锻造
(Steel die forgings - Tolerances on dimensions
- Part 1 : drop and vertical press forgings.)
NF E86-011-1998 用于装空气或氮气的,不置于火中的简单压力容器.第1部分:一般用途用压力容器
(Simple unfired pressure vessels designed to
contain air or nitrogen. Part 1 : pressure vessels
for general purposes.)
NF E86-011/A1-2002 用于装空气或氮气的简易非受火压力容器.第1部分:一般用途的压力容器
(Simple unfired pressure vessels designed to
contain air or nitrogen - Part 1 : pressure
vessels for general purposes.)
NF E86-012-1992 含空气或氮气的不用火加热的简单压力容器.第2部分:用于汽车及其挂车制动和辅助系统的压力容器
(Simple unfired pressure vessels designed to
contain air or nitrogen. Part 2 : pressure vessels
for air braking and auxiliary systems for motor-vehicles
and their trailers.)
NF E86-020-1974 气体压力设备.带标号的调整标记板 (GAS PRESSURE
VESSELS.NAME PLATE FOR STATUTORY IDENTIFICATION
MARKINGS.)
NF E86-021-1989 压力或无压卧式或立式锅炉设备.外部尺寸和标准容量 (PRESSURIZED
OR NOT PRESSURIZED TANKS,HORIZONTAL OR VERTICAL.
EXTERNAL DIMENSIONS AND CAPACITIES.)
NF E86-200-1-2002 不用火加热的压力容器.第1部分:总则 (Unfired
pressure vessels - Part 1 : general.)
NF E86-200-2-2002 不用火加热的压力容器.第2部分:材料 (Unfired
pressure vessels - Part 2 : materials.)
NF E86-200-3-2002 不用火加热的压力容器.第3部分:设计 (Unfired
pressure vessels - Part 3 : design.)
NF E86-200-4-2002 不用火加热的压力容器.第4部分:制造 (Unfired
pressure vessels - Part 4 : manufacture.)
NF E86-200-5-2002 不用火加热的压力容器.第5部分:检测和试验 (Unfired
pressure vessels - Part 5 : inspection and testing.)
NF E86-200-6-2002 不用火加热的压力容器.第6部分:用球墨铸铁建造的压力容器和压力部件的设计和制造要求
(Unfired pressure vessels - Part 6 : requirements
for the design and fabrication of pressure vessels
and pressure parts constructed from spheroidal
graphite cast iron.)
NF E86-271-1976 压力运输设备.有凸出端部的氯贮槽.容量８００l.制造和检验
(PRESSURE TRANSPORT STOCK. CONVEX-BASED CONTAINERS
FOR CHLORINE. CAPACITY 800 LITRES. CONSTRUCTION
AND TESTS.)
NF E86-504-1-2002 冷凝容器.静置真空绝缘压力容器.第1部分:基本原理要求
(Cryogenic vessels - Static vacuum insulated
vessels - Part 1 : fundamental requirements.)
NF E86-601-2-2003 检漏系统.第2部分:压力和真空系统 (Leak detection
systems - Part 2 : pressure and vacuum systems.)
NF F11-040-1994 装空气或氮气用的不近火的一般压力容器.第3部分:用于铁路运输车辆空气制动和辅助气动设备的钢制压力容器
(Simple unfired pressure vessels designed to
contain air or nitrogen. Part 3 : steel pressure
vessels designed for air braking equipment and
auxiliary pneumatic equipment for railway rolling
stock.)
NF F11-042-1994 装空气或氮气用的一般不近火的压力容器.第4部分:用于铁路运输车辆空气制动和辐助气动设备的铝合金压力容器
(Simple unfired pressure vessels designed to
contain air or nirogen. Part 4 : aluminium alloy
pressure vessels designed for air braking equipment
and auxiliary penumatic equipment for railway
rolling stock.)
NF F37-0221-1979 铁路车辆.“盐酸“类罐车.直径为50mm和80mm压力排空圆顶盖
()
NF F37-040-1977 铁路车辆.底部技压灌注排放的液化气罐车.压力小于40bar.计量.排气和试验用孔
(RAILWAY TRANSPORT EQUIPMENT. TANK WAGONS FOR
CARRYING LIQUIFIED GASES UNDER PRESSURE AND
HAVING BOTTOM FILLING AND EMPTYING DEVICES.
MAXIMUM SERVICE PRESSURE 40 BARS. AIR ORIFICE
FOR GAUGING,DEGASSING AND TESTING.)
NF F37-100-3-2003 铁路设施.油罐车.第3部分:压力下液化气用底部装卸式装置
(Railway applications - Tank wagons - Part 3
: bottom filling and emptying devices for gases
liquefied under pressure.)
NF F38-001-1975 铁路运输设备.采用最大压力为2.5bar排空的散装粉状产品运输用气动排空车.粉导管用统一接头
(RAILWAY TRANSPORT EQUIPMENT. WAGONS WITH PNEUMATIC
DISCHARGE,FOR CARRYING POWDER GOODS IN BULK
WITH DISCHARGE AT MAXIMUM OPERATING PRESSURE
OF 2.5 BAR. STANDARD AIR PIPE CONNECTION.)
NF F38-002-1971 铁路运输设备.采用最大压力为2.5bar排空的散粉状产品运输用气动排空车.散粉导管用统一接头
(RAILWAY TRANSPORT EQUIPMENT. WAGONS WITH PNEUMATIC
DISCHARGE FOR CARRYING POWDER GOODS IN BULK.
DISCHARGE AT MAXIMUM SERVICE PRESSURE OF 2.5
BARS.)
NF F38-002M-1976 铁路运输设备.采用最大压力为2.5bar的散装粉状产品运输用气动排空车.排空粉导管用统一接头
()
NF G07-212-2001 织物.织物对熨斗压力尺寸稳定性的测定 (Textiles
- Determination of the dimensional stability
of fabrics to ironing presses.)
NF G38-107-2-1996 建工织物相关产品.特定压力下厚度测定.第2部分:多层产品的单层厚度的测定过程(欧洲标准
EN ISO 9863-2) (GEOTEXTILES AND EOTEXTILE-RELATED
PRODUCTS. DETERMINATION OF THICKNESS AT SPECIFIED
PRESSURES. PART 2 : PROCEDURE FOR DETERMINAITON
OF THICKNESS OF SINGLE LAYERS OF MULTILAYER
PRODUCTS. (EUROPEAN STANDARD EN ISO 9863-2).)
NF G45-102-1998 工业洗衣机的安全要求.第6部分:熨衣压力机 (Safety
requirements for industrial laundry machinery.
Part 6 : ironing and fusing presses.)
NF H35-109-1997 装瓶工业.玻璃瓶.苹果汁.压力类型冠形盖瓶口29.尺寸
(Bottling industry. Glass bottles. Cider, pressure
type crown finish 29. Dimensions.)
NF H35-110-1997 装瓶工业.75 CL苹果汁压力类型 (Bottling
industry. Glass bottles. 75 cl Cider pressure
type.)
NF H44-006-1988 烟雾发生器.压力分配用铝和铝合金容器（气雾剂容器型）与膨胀管联系的底部尺寸公差
(AEROSOL DISPENSERS. CONTAINERS IN ALUMINIUM
AND ALLOYS. TOLERANCES OF THE FUNDAMENTAL DIMENSIONS
IN CONNECTION WITH THE CLINCH.)
NF H44-016-1988 烟雾发生器.压力分配容器（气雾剂容器型）.铝制２０mm容器瓶口尺寸
(AEROSOL DISPENSERS. ALUMINIUM MONOBLOC CONTAINERS.
DIMENSIONS OF THE 20 MM FINISH.)
NF H44-018-1988 烟雾发生器.压力分配容器（气雾剂容器型）.２５．４mm孔径容器.平行度的定义和测定
(AEROSOL DISPENSERS. CONTAINERS WITH A 25,4
MM OPENING. MEASUREMENT OF THE NECK PARALLELISM
AND SURFACE EVENESS.)
NF H44-020-1988 烟雾发生器.压力分配容器（气雾剂容器型）.气雾剂容器上阀门的机械密封和安装的快速试验
(AEROSOL DISPENSERS. RAPID TEST. TIGHTNESS OF
VALVE MECHANISMS AND CLINCH.)
NF J24-010-1957 造船工业.软管.使用总表.直径.材料.接合型.用途.压力
(SHIPBUILDING. FLEXIBLE PIPING. GENERAL TABLE.
DIAMETERS. MATERIALS. TYPES OF JOINT. APPLICATIONS.
PRESSURES.)
NF J25-535-1958 造船工业.海水专用阀门.压力收集箱.组装件.一般尺寸 (SHIPBUILDING.
SEA WATER VALVES. DELIVERY MANIFOLD VALVES.
ASSEMBLY. GENERAL DIMENSIONS.)
NF J38-540-2002 船舶和造船技术.载油舱用压力/真空阀 (Ships and
marine technology - Pressure/vacuum valves for
cargo tanks.)
NF J41-450-1957 造船工业.“金士顿“阀门.压力填圈.压盖和衬套 (SHIPBUILDING.
KINGSTON VALVES. STUFFING BOX,GLAND AND BUSHING.)
NF L10-600-5-1990 航空和航天系列.铝合铝合金锻制半成品.技术规范.第5部分:压力管
(AEROSPACE SERIES. ALUMINIUM AND ALUMINIUM ALLOY
WROUGHT PRODUCTS. TECHNICAL SPECIFICATION. PART
5 : TUBE USED UNDER PRESSURE. (EUROPEAN STANDARD
EN 2070-5).)
NF L44-540-1974 甲醇水压力供水接头.标定尺寸19mm (Water-methanol
pressure connections. Nominal dimension 19 mm.)
NF L44-541-1974 甲醇水压力供水接头.标定尺寸38mm (Water-methanol
pressure connections. Nominal dimension 38 mm.)
NF L44-550-1978 润滑油压力注入接头 (Pressure re-oiling
connection.)
NF L45-101-1987 航空和航天.液力、压力补偿或变量输送泵.一般要求 (Aerospace.
Hydraulic, pressure compensated, variable delivery
pumps. General requirements.)
NF L72-310-1986 航空器材.圆盘式机载压力表 (Aircraft equipment.
On board pressure indicator with round dials.)
NF M07-002-2000 石油产品.空气压力下蒸馏特性的测定 (Petroleum
products - Determination of distillation characteristics
at atmospheric pressure.)
NF M07-079-1-2000 液化石油产品.蒸气压力.第1部分:空气饱和蒸气压力的测定
(Liquid petroleum products - Vapour pressure
- Part 1 : determination or air saturated vapour
pressure (ASVP).)
NF M07-079-2-2000 液化石油产品.蒸气压力.第2部分:40度和100度之间绝对蒸气压力的测定
(Liquid petroleum products - Vapour pressure
- Part 2 : determination of absolute vapour
pressure (AVP) between 40 oC and 100 oC.)
NF M41-008-1995 液化石油气和轻质烃类.密度或相对密度的测定.压力石油密度计法
(Liquefield petroleum gas and light hydrocarbons.
Determination of density or relative density.
Pressure hydrometer method.)
NF M41-010-1998 液化石油器.量规蒸气压力的测定.LPG法 (Liquefied
petroleum gases. Determination of gauge vapour
pressure. LPG method.)
NF M50-005-1-2000 燃气供应系统.最大操作压力高达(和包括)16巴的管线.第1部分:一般功能推荐
(Gas supply systems - Pipelines for maximum
operating pressure up to and including 16 bar
- Part 1 : general functional recommendations.)
NF M50-005-2-2000 燃气供应系统.最大操作压力高达(和包括)16巴的管线.第2部分:聚乙烯管的特殊功能推荐
(Gas supply systems - Pipelines for maximum
operating pressure up to and including 16 bar
- Part 2 : specific functional recommendations
for polyethylene (MOP up to and including 10
bar).)
NF M50-005-3-2000 燃气供应系统.最大操作压力高达(和包括)16巴的管线.第3部分:钢的特殊功能推荐
(Gas supply systems - Pipelines for maximum
operating pressure up to and including 16 bar
- Part 3 : specific functional recommendations
for steel.)
NF M50-005-4-2000 燃气供应系统.最大操作压力高达(和包括)16巴的管线.第4部分:修理的特殊功能推荐
(Gas supply systems - Pipelines for maximum
operating pressure up to and including 16 bar
- Part 4 : specific functional recommendations
for renovation.)
NF M50-009-2000 燃气供应系统.最大工作压力达(和包括)16巴的燃气管道.功能要求
(Gas supply systems - Pipelines for maximum
operating pressure over 16 bar - Functional
requirements.)
NF M50-015-2000 燃气供应系统.运输气体的管线的气体压力调节安装.功能要求
(Gas supply systems - Gas pressure regulating
installations on service lines - Functional
requirements.)
NF M50-016-2000 燃气供应系统.运输和分配气体的气体压力调节站.功能要求
(Gas supply systems - Gas pressure regulating
stations for transmission and distribution -
Functional requirements.)
NF M62-301-5-2002 压力壳部件.第5部分:电路和流体回路的渗透性 (Components
for containment enclosures - Part 5 : penetrations
for electrical and fluid circuits.)
NF M88-072-1983 运输和装卸.未冷冻压力溶解液化气道路罐车.下部装卸装置
(Transport and materials handling. Road tankers
for non-refrigerated liquefied and dissolved
gas under pressure. Floor filling and draining
devices.)
NF M88-080-1984 道路油罐车.液态化学产品金属油罐.压力排放装置:管状柱塞,进气孔
(ROAD TANKER VEHICLES. METALLIC TANKERS FOR
LIQUID CHEMICAL PRODUCTS. DEVICES EFFECTING
DISCHARGE BY MEANS OF PRESSURE : PLUNGER TUBE,AIR
OFF-TAKE.)
NF M88-114-1982 罐车.液化气运输.4-40ba工作压力的DN50.DN80和DN100的止流和安全内部阀门
(ROAD TANKERS. TRANSPORTATION OF LIQUEFIED GASES.
INTERNAL STOP AND SAFETY OBTURATOR. NOMINAL
DIAMETERS DN 50,DN 80 AND DN 100 FOR SERVICE
PRESSURE BETWEEN 4 BAR AND 40 BAR.)
NF M88-131-2003 危险物品运输用槽罐车.槽罐车用辅助设备.压力平衡底阀 (Tanks
for transport of dangerous goods - Service equipment
for tanks - Pressure balanced footvalve.)
NF M88-555-1-1997 玻璃增强塑料(GRP)制地下油罐.非压力储存液化石油基燃油用卧式圆柱形油罐.第1部分:单壁罐的要求和试验方法
(Underground tanks of glass-reinforced plastics
(GRP). Horizontal cylindrical tanks for the
non-pressure storage of liquid petroleum based
fuels. Part 1 : requirements and test methods
for single wall tanks.)
NF M88-555-2-1997 玻璃增强塑料(GRP)制地下油罐.非压力储存液化石油基燃油用卧式圆柱形油罐.第2部分:单壁罐的运输、装卸、储
(Underground tanks of glass-reinforced plastics
(GRP). Horizontal cylindrical tanks for the
non-pressure storage of liquid petroleum based
fuels. Part 2 : transport, handling, storage
and installation of single wall tanks.)
NF M88-774-1983 液化烃容器装置.民房建设用压力限制器 (LIQUEFIED
HYDROCARBON INSTALLATIONS. PRESSURE RELIEF VALVE
FOR RESIDENTIAL BUILDINGS.)
NF P16-341-1990 排水.无压力排水管路用钢筋混凝土和非钢筋混凝土制圆管.定义、规范、试验方法、标记、验收条件
(Drainage, sewerage. Precast concrete cylindrical
pipes, steel reinforced or not reinforced for
sewerage networks without pressure. Definitions,
specifications, testing methods, marking, basis
for acceptance.)
NF P16-352-1-1998 非压力地下管道和废水用塑料管道系统.非塑化聚(乙烯,氯乙烯)(PVC-D).第1部分:管道规范,配件和系统
(Plastics piping systems for non-pressure underground
drainage and sewerage. Unplasticized poly(vinyl
chloride) (PVC-U). Part 1 : specifications for
pipes, fittings and the system.)
NF P16-358-1-2001 地下和地上排水和排污用塑料压力管道系统.未增塑聚氯乙烯(PVC-U).第1部分:管道元件和系统规范
(Plastics piping systems for buried and above-ground
drainage and sewerage under pressure - Unplasticized
poly(vinyl chloride) (PVC-U) - Part 1 : specifications
for piping components and the system.)
NF P16-364-1-2003 地下非压力排水和污水管网更新用塑料管道系统.第1部分:总则
(Plastics piping systems for renovation of underground
non-pressure drainage and sewerage networks
- Part 1 : general.)
NF P16-364-3-2003 地下非压力排水和污水管网更新用塑料管道系统.第3部分:紧配合管用衬层
(Plastics piping systems for renovation of underground
non-pressure drainage and sewerage network -
Part 3 : lining with close-fit pipes.)
NF P16-364-4-2003 地下非压力排水和污水网用塑料管道系统.第4部分:现场固化管用的管衬
(Plastics piping systems for renovation of underground
non-pressure drainage and sewerage networks
- Part 4 : lining with cured-in-place pipes.)
NF P16-400-1997 建筑物外压力脱水系统 (PRESSURE SEWERAGE
SYSTEMS OUTSIDE BUILDINGS. (EUROPEAN STANDARD
EN 1671).)
NF P18-443-2001 试验新鲜混凝土.第7部分:空气含量.压力方法 (Testing
fresh concrete - Part 7 : air content - Pressure
methods.)
NF P18-937-1998 混凝土结构制造和修复的产品和系统.修理砖石结构的压力强度的测定(欧洲标准EN
12190) (Products and systems for the protection
and repair of concrete structures. Test methods.
Determination of compressive strength of repair
mortar.)
NF P20-539-2001 窗.机械特性的分类.压力、扭力和操纵力 (Windows
- Classification of machanical properties -
Racking, torsion and operating forces.)
NF P28-104-2000 幕墙.水密性.静态压力下的试验室试验 (Curtain
walling - Watertightness - Laboratory test under
static pressure.)
NF P41-211/A1-2000 DTU 60.31.建筑工程.非塑化聚氯乙烯管道安装.压力下冷水.技术规范
(DTU 60.31 - Building works - Unplasticized
polyvinyl chloride piping installation - Cold
water under pressure - Technical specifications.)
NF P41-302-1994 纤维水泥制品.压力管道和接头(欧洲标准EN 512) (Fibre-cement
products. Pressure pipes and joints.)
NF P41-302/A1-2002 纤维混凝土制品.压力管和连接件 (Fibre-cement
products - Pressure pipes and joints.)
NF P41-400-1995 包括接头和配件的混凝土压力管的共同要求 (Common
requirements for concrete pressure pipes including
joints and fittings.)
NF P41-401-1995 包括接头和配件的非圆柱型加筋混凝土压力管 (Reinforced
concrete pressure pipes and distributed reinforcement
concrete pressure pipes (non-cylinder type),
including joints and fittings.)
NF P41-402-1995 包括接头和配件的圆柱型加筋混凝土压力管 (Reinforced
concrete pressure pipes, cylinder type, including
joints and fittings.)
NF P41-403-1995 包括接头和配件的圆柱型和非圆柱型预应力混凝土压力管及管用预应力钢的具体要求
(Prestressed concrete pressure pipes, cylcinder
and non-cylinder, including joints, fittings
and specific requirement for prestressing steel
for pipes.)
NF P43-011-1985 建筑物水管阀门.非控制不同压力范围CB断路器.一般技术规范
(VALVES AND TAPS FOR WATER SUPPLY IN BUILDINGS.
CB DISCONNECTORS WITH DIFFERENT NON CONTROLLABLE
PRESSURE RANGES. GENERAL TECHNICAL SPECIFICATIONS.)
NF P45-200-1998 燃气供应.燃气管道工程和建筑.大于或等于5Bar的最大操作压力.功能推荐
(Gas supply - Gas pipework for buildings - Maximum
operating pressure inferior or equal to 5 bar
- Functional recommendations.)
NF P45-200/A1-2000 燃气供应.建筑物的燃气管道工程.小于或等于5巴的最大操作压力.功能推荐
(Gas supply - Gas pipework for buildings - Maximum
operating pressure up to and including 5 bar
- Functional recommendations.)
NF P45-200/A2-2002 燃气供应.建筑物的燃气管道工程.高达和包括5巴的最大操作压力.功能推荐
(Gas supply - Gas pipework for buildings - Maximum
operating pressure up to and including 5 bar
- Functional recommendations.)
NF P50-760-2002 建筑构件和建筑元件的湿温性能.脉动式空气压力下外墙耐雨水的测定
(Hygrothermal performance of building components
and building elements - Determination of the
resistance of external wall systems to driving
rain under pulsating air pressure.)
NF P52-211-1/A1-2000 DTU 65.3.建筑工程.压力热水的热交换装置.技术规范
(DTU 65.3 - Building works - Heat exchange installations
for pressurised hot water - Part : Technical
specifications.)
NF P52-305-1/A1-1999 DTU 65.10.建筑工程.建筑物内雨水和废水排空用冷热压力水用管道.排空的一般规则.第1部分:技术规范
(DTU 65.10 - Building works - Piping used for
cold and hot pressure water and piping for evacuation
waste water and rain water inside buildings
- General rules of execution - Part 1 : technical
specifications.)
NF P52-305-1/A2-2000 DTU 65.10.建筑工程.建筑物内雨水和废水排空用冷热压力水用管道.排空的一般规则.第1部分:技术规范
(DTU 65.10 - Building works - Piping used for
cold and hot pressure water and piping for evacuation
waste water and rain water inside buildings
- General rules of execution - Part 1 : technical
specifi)
NF P52-305-2-1993 DTU 65-10.建筑工程.个人合同.用于冷和热压力水和建筑物内排除废水和雨水的管道的铺设.排除的一般规则.第2
(DTU 65-10. BUILDING WORKS. PRIVATE CONTRACTS.
PIPING USED FOR COLD AND HOT PRESSURE WATER
AND PIPING FOR EVACUATION WASTE WATER AND RAIN
WATER INSIDE BUILDINGS. GENERAL RULES OF EXECUTION.
PART 2 : SPECIAL CLAUSES.)
NF P78-407-2001 建筑物用玻璃.保险玻璃.防爆炸压力的试验和分类 (Glass
in building - Security glazing - Testing and
classification of resistance against explosion
pressure.)
NF P85-551-1998 密封缝隙用产品.密封用上釉材料和化合物.预制带材密封剂.压力下特性的测定
(Jointing products. Glazing materials and compounds
for sealing. Sealants in preformed strips. Determination
of characteristics under compression.)
NF P94-074-1994 土壤:调查与试验.用三轴试验仪器测剪切强度试验.仪器.试验标本的制备.松散的、不排水的(UU)试验.带有孔隙压
()
NF P94-119-1995 土壤:调查和试验.压力锥印试验.CPTU (SOIL :
INVESTIGATION AND TESTING. PIEZOCONE TEST. CPTU.)
NF P94-150-1991 土壤.检验与试验.独立板桩在轴向压力下的静力试验 (SOILS
: INVESTIGATION AND TESTING. STATIC COMPRESSION
TEST ON SINGLE PILE.)
NF P94-157-1-1996 土壤:调查和试验.现场孔隙压力测量.第1部分:测压管
(SOILS : INVESTIGATION AND TESTING. IN SITU
PORE PRESSURE MEASUREMENT. PART 1 : PIEZOMETRIC
TUBE.)
NF P94-157-2-1996 土壤:调查和试验.现场孔隙压力测量.第2部分:孔隙压力计
(SOILS : INVESTIGATION AND TESTING. IN SITU
PORE PRESSURE MEASUREMENT. PART 2 : PORE PRESSURE
METER.)
NF P98-760-1991 筑路和养路设备.材料.气压夯实机.对路面压力的评估 (ROAD
CONSTRUCTION AND MAINTENANCE EQUIPMENT. PNEUMATIC.
TIRED. COMPACTORS. EVALUATION OF THE CONTACT
PRESSURE ON SOIL.)
NF Q03-033-1994 单面和单壁瓦楞纤维纸板耐压力的测定 (Single-faced
and single-wall corrugated fibreboard. Determination
of flat crush resistance.)
NF R10-014-2002 道路车辆.使用压力检测计进行曲柄轴箱压力测量法 (Road
vehicles - Crankcase pressure measurement procedure
using a pressure probe.)
NF R12-650-1984 道路车辆.压缩气制动设备的压力传感器 (Road vehicles.
Pressure test connection for compressed-air
pneumatic braking equipment.)
NF R12-651-1984 道路车辆,液压制动设备的压力传感器 (Road vehicles.
Hydraulic pressure test connection for braking
equipment.)
NF R41-150-1970 托车和半托车.空气压力制动连接 (TRAILERS AND
SEMI-TRAILERS.AIR-PRESSURE BRAKING CONNECTIONS.)
NF R63-302-1999 压力仪表.摩托车轮胎压力和/或膨胀率用检查仪器 (Pressure
gauges. Apparatus for inspection of pressure
and/or inflation of tyres for motor vehicles.
Metrology, requirements and testing.)
NF S30-007-2-1996 声学.纯音听力计设备校正的参考零点.插入式耳机和纯音调用参考等效域值声音压力水平
(ACOUSTICS. REFERENCE ZERO FOR THE CALIBRATION
OF AUDIOMETRIC EQUIPMENT. PART 2 : REFERENCE
EQUIVALENT THRESHOLD SOUND PRESSURE LEVELS FOR
PURE TONES AND INSERT EARPHONES. (EUROPEAN STANDARD
EN ISO 389-2).)
NF S31-024-2-1996 声学.使用声音压力对噪声源的声音功率级的测定.在混响声场中小声源和移动声源的工程测量方法.第2部分:特殊
(Acoustics. Determination of sound power levels
of noise sources using sound pressure. Engineering
methods for small, mowable sources in reverberant
fields. Part 2 : methods for special reverberation
test rooms.)
NF S31-108-1994 电声学.声强测量仪.测量用双压力传感传声器 (Electroacoustics.
Instruments for the measurement of sound intensity.
Measurement with pairs of pressure sensing microphones.)
NF S31-127-1995 声学.消音输送道测量步骤.插入损耗,流动噪声和压力损失
(Acoustics. Measurement procedures for ducted
silencers. Insertion loss, flow noise and total
pressure loss.)
NF S31-500-1997 声学.机械和设备发出的噪音.工作场所或其它特殊位置声音压力水平发出的测定用基本标准的使用导则
(ACOUSTICS. NOISE EMITTED BY MACHINERY AND EQUIPMENT.
GUIDELINES FOR THE USE OF BASIC STANDARDS FOR
THE DETERMINATION OF EMISSION SOUND PRESSURE
LEVELS AT A WORK STATION AND AT OTHER SPECIFIED
POSITIONS. (EUROPEAN STANDARD EN ISO 11200).)
NF S61-112-1975 消防设备.直径25、36.5、45、70、110mm的压力水龙带
(FIRE FIGHTING EQUIPMENT - DISCHARGE FLEXIBLE
HOSES - 25 - 36,5 - 45- 70 - 110.)
NF S61-704-1966 消防设备.压力输送用40和65mm自动关闭对称半接头 (FIRE
FIGHTING EQUIPMENT. SELF-SEALING SYMMETRICAL
HALF COUPLINGS,SIZES 40 AND 65.)
NF S62-140-2003 固定消防系统.气体灭火系统元件.第10部分:压力计和压力开关的试验方法和要求
(Fixed firefighting systems - Components for
gas extinguishing systems - Part 10 : requirements
and test methods for pressure gauges and pressure
switches.)
NF S66-254-1-2003 气体和蒸气的最大爆炸压力和最大压升的测定.第1部分:最大爆炸压力的测定
(Determination of the maximum explosion pressure
and maximum rate of pressure rise of gases and
vapours - Part 1 : determination of the maximum
explosion pressure.)
NF S74-512-1994 防护服.防护气体和蒸气的试验方法.泄漏的测定(内压力试验)
(PROTECTIVE CLOTHING. PROTECTION AGAINST LIQUID
AND GASEOUS CHEMICALS, INCLUDING AEROSOLS LIQUID
AND SOLID PARTICLES. TEST METHOD : DETERMINATION
OF LEAK-TIGHTNESS OF GAS-TIGHT SUITS (INTERNAL
PRESSURE TEST). (EUROPEAN STANDARD EN 464).)
NF S95-153-2001 医疗抽吸设备.第3部分:真空或压力源驱动的抽吸设备 (Medical
suction equipment - Part 3 : suction equipment
powered from a vacuum or pressure source.)
NF S95-159-1997 与医疗麻醉剂一起使用的压力调节器.第1部分:压力调节器和带流量测量装置的压力调节器(欧洲标准EN
738-1) (PRESSURE REGULATORS FOR USE WITH MEDICAL
GASES. PART 1 : PRESSURE REGULATORS AND PRESSURE
REGULATORS WITH FLOW METERING DEVICES. (EUROPEAN
STANDARD EN 738-1).)
NF S95-159/A1-2002 医用气体压力调节器.第1部分:压力调节器和带流量计的压力调节器
(Pressure regulators for use with medical gases
- Part 1 : pressure regulators and pressure
regulators with flow metering devices.)
NF S95-171-1999 医用气体用压力调节器.多功能的和线状压力调节器(欧洲标准738-2)
(PRESSURE REGULATORS FOR USE WITH MEDICAL GASES.
PART 2 : MANIFOLD AND LINE PRESSURE REGULATORS.
(EUROPEAN STANDARD EN 738-2).)
NF S95-178-1998 医用气体用压力调节器.第3部分:与钢瓶阀门相结合的压力调节器(欧洲标准EN
738-3) (PRESSURE REGULATORS FOR USE WITH MEDICAL
GASES. PART 3 : PRESSURE REGULATORS INTEGRATED
WITH CYLINDER VALVES. (EUROPEAN STANDARD EN
738-3).)
NF S95-178/A1-2002 医用气体压力调节器.第3部分:带瓶阀的压力调节器
(Pressure regulators for use with medical gases
- Part 3 : pressure regulators integrated with
cylinder valves.)
NF S95-179-1998 用于医用气体的压力调节器.第4部分:结合医用设备的低压调节器(欧洲标准EN
738-4) (PRESSURE REGULATORS FOR USE WITH MEDICAL
GASES. PART 4 : LOW-PRESSURE REGULATORS INTENDED
FOR INCORPORATION INTO MEDICAL EQUIPMENT. (EUROPEAN
STANDARD EN 738-4).)
NF S95-179/A1-2002 医用气体压力调节器.第4部分:装入医疗设备的低压调节器
(Pressure regulators for use with medical gases
- Part 4 : low-pressure regulators intended
for incorporation into medical equipment.)
NF T30-020-4-2001 涂料和清漆.密度的测定.第4部分:压力杯法 (Paints
and varnishes - Determination of density - Part
4 : pressure cup method.)
NF T30-137-1994 色漆和清漆.堆积压力试验 (PAINTS AND VARNISHES.
PRESSURE TEST FOR STACKABILITY. (EUROPEAN STANDARD
EN ISO 4622).)
NF T46-043-1983 硫化橡胶.正常温度和高温下挤压力消除的测定（环状试件）
(VULCANIZED RUBBER. DETERMINATION OF COMPRESSION
STRESS RELAXATION AT NORMAL AND ELEVATED TEMPERATURES
(ANNULAR TEST-PIECES).)
NF T47-251-1-1997 橡胶和塑料软管和软管组件.试验压力和爆破压力与设计工作压力的比值
(RUBBER AND PLASTICS HOSES AND HOSE ASSEMBLIES.
RATIOS OF PROOF AND BURST PRESSURE TO DESIGN
WORKING PRESSURE. (EUROPEAN STANDARD EN ISO
7751).)
NF T54-007-1994 塑料管道系统.压力管和配件的机械接合.在恒定应力下抗拔出性能的试验方法
(THERMOPLASTICS PIPING SYSTMES. END-LOAD BEARING
MECHANICAL JOINTS BETWEEN PRESSURE PIPES AND
FITTINGS. TEST METHOD FOR RESISTANCE TO PULL-OUT
UNDER CONSTANT LONGITUDINAL FORCE. (EUROPEAN
STANDARD EN 712).)
NF T54-008-1994 塑料管道系统.配件和聚烯烃压力管的机械接合.在弯曲时内部压力引起的密封性的试验方法
(PLASTICS PIPING SYSTEMS. MECHANICAL JOINTS
BETWEEN FITTINGS AND POLYOLEFIN PRESSURE PIPES.
TEST METHOD FOR LEAKTIGHTNESS UNDER INTERNAL
PRESSURE OF ASSEMBLIES SUBJECTED TO BENDING.
(EUROPEAN STANDARD EN 713).)
NF T54-009-1994 热塑料管道系统.压力管和模塑配件的合成橡胶密封环型接合.在无轴向推力时内部流体静力学压力下密封性的试验
(THERMOPLASTICS PIPING SYSTEMS. NON-END-LOAD-BEARING
ELASTOMERIC SEALING RING TYPE JOINTS BETWEEN
PRESSURE PIPES AND MOULDED FITTINGS. TEST METHOD
FOR LEAKIGHTNESS UNDER INTERNAL HYDROSTATIC
PRESSURE WITHOUT END THRUST. (EUROPEAN STANDARD
EN 714).)
NF T54-010-1994 塑料管道系统.压力管和配件的机械和胶合接合.在包含轴向推力的内部水压下密封性的试验方法
(THERMOPLASTICS PIPING SYSTEMS. END-LOAD BEARING
JOINTS BETWEEN SMALL DIAMETER PRESSURE PIPES
AND FITTINGS. TEST METHOD FOR LEAKTIGHTNESS
UNDER INTERNAL WATER PRESSURE, INCLUDING END
THRUST. (EUROPEAN STANDARD EN 715).)
NF T54-012-1995 塑料管道系统.热塑塑料压力管道用的弹性密封环型接头和机械接头.外部液压条件下防漏密封试验方法
(PLASTICS PIPING SYSTEMS. ELASTOMERIC SEALING
RING TYPE JOINTS AND MECHANICAL JOINTS FOR THERMOPLASTICS
PRESSURE PIPING. TEST METHOD FOR LEAKTIGHTNESS
UNDER EXTERNAL HYDROSTATIC PRESSURE. (EUROPEAN
STANDARD EN 911).)
NF T54-029-1981 塑料.未增塑聚氯乙烯模制接头.压力系列.规范 (Plastics.
Moulded unplasticized PVC fittings. Pressure
series. Specifications.)
NF T54-038-1981 装配有压力管用密封圈的未增塑聚氯乙烯管和接头.尺寸特性
(Unplasticized polyvinyl chloride pipes and
fittings. Assembly by sealing rings for pressure
pipelines. Dimensional caracteristics.)
NF T54-039-1988 塑料.未增塑聚氯乙烯压力管用密封圈的固定接头.使用特性.规范
(Plastics. Unplasticized polyvinyl chloride
pipes and fittings. Assembly by sealing rings
for pressure pipelines. Fitness for use.)
NF T54-041-1994 塑料管道系统.压力管道用弹性密封圈型接头的热注塑料配件.耐无轴向力短暂内压力性能的试验方法
(Plastics piping systems. Injection-moulded
thermoplastics fittings for elastic sealing
ring type joints for pressure piping. Test method
for resistance to a short-term internal pressure
without end thrust.)
NF T54-042-1994 塑料管道系统.压力管道用溶剂-水泥胶合接头的注模承窝配件
(Plastics piping systems. Injection-moulded
socket fittings for solvent-cemented joints
for pressure piping. Test method for resistance
to a short-term internal hydrostatic pressure.)
NF T54-045-1994 塑料管道和导管系统.压力管道系统用热注塑料配件.最大变形的挤撞试验法
(Plastics piping and ducting systems. Injection-moulded
thermoplastics fittings for pressure piping
systems. Test method for maximum deformation
by crushing.)
NF T54-059-1995 压力管道和配件用热塑性塑料.分类和名称与符号.总体设备的设计系数
(Thermoplastics materials for pipes and fittings
for pressure applications. Classification and
designation. Overall service (design) coefficient.)
NF T54-064-1990 塑料.带紧箍的半离合器系统(吉可曼系统).公称压力PN6
(PLASTICS-HALF SYMMETRIC FITTING (GUILLEMIN
SYSTEM) WITH LOCKING RING. NOMINAL PRESSURE
PN 6.)
NF T54-085-1988 塑料.液体压力管用网状线聚乙烯管.规范 (Plastics.
Reticulate polyethylene pipes for pipelines
under pressure. Specifications.)
NF T54-118-2001 塑料.在大气压力下薄膜和薄板的透气率的测定.测压法 (Plastics
- Determination of the gas transmission rate
of films and thin sheets under atmospheric pressure
- Manometric method.)
NF T54-300-1-2003 普通用水、排水、污水地上和地下压力系统用塑料管道系统.聚乙烯(PE).第1部分:总则
(Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
Part 1 : general.)
NF T54-300-2-2003 普通用水、排水、污水地上和地下压力系统用塑料管道系统.聚乙烯(PE).第2部分:管道
(Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
Part 2 : pipes.)
NF T54-300-3-2003 普通用水、排水、污水地下和地上压力系统用塑料管道系统.聚乙烯(PE).第3部分:管件
(Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
Part 3 : fittings.)
NF T54-300-4-2003 普通用水、排水、污水地下和地上压力系统用塑料管道系统.聚乙烯(PE).第4部分:阀门
(Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
Part 4 : valves.)
NF T54-300-5-2003 普通用水、排水、污水地下和地上压力系统用塑料管道系统.聚乙烯(PE).第5部分:系统的适用性
(Plastics piping systems for buried and above-ground
pressure systems for water for general purposes,
drainage and sewerage - Polyethylene (PE) -
Part 5 : fitness for purpose of the system.)
NF T54-901-1995 塑料管道系统.非压力设备用热塑管道系统.不透水性试验方法(欧洲标准EN
1053) (Plastics piping systems. Thermoplastics
piping systems for non-pressure applications.
Test method for watertightness.)
NF T54-905-2002 塑料管道系统.热塑性压力管用端部承载或非端部承载组件和接头.内部水压下长期无漏损的试验方法
(Plastics piping systems - End-load-bearing
and non-end-load-bearing assemblies and joints
for thermoplastics pressure piping - Test method
for long-term leaktightness under internal water
pressure.)
NF T54-926-2000 热塑性管道系统.地下常压排污设施用接头.用密封压力评定法测定带热塑性弹性体(TPE)密封件接头的长期密封性
(Thermoplastics piping systems - Joints for
buried non-pressure sewage applications - Test
method for long-term sealing performance of
joints with thermoplastic elastomer (TPE) seals
by estimating the)
NF T54-942-1999 塑料管道系统.输送热水和冷水用的热塑管和附属配件.连接件对压力变化负载的稳定性的检测方法
(Plastics piping systems - Thermoplastics pipes
and associated fittings for hot and cold water
- Test method for resistance of joints to pressure
cycling.)
NF T54-945-1998 压力下流体运输用塑料管.Miner法则.累积损伤的计算方法
(PLASTICS PIPES FOR THE CONVEYANCE OF FLUIDS
UNDER PRESSURE. MINER`S RULE. CALCULATION METHOD
FOR CUMULATIVE DAMAGE. (EUROPEAN STANDARD EN
ISO 13760).)
NF T57-204-1996 塑料管道系统.玻璃增强热固性塑料(GRP)管.耐长期内部压力性能的测定
(Plastics piping systems. Glass-reinforced thermosetting
plastics (grp) pipes. Determination of long-term
resistance to internal pressure.)
NF T57-214-1-1998 地下排水系统和压力下污水排放的塑料管道系统.基于不饱和聚酯
树脂(UP)的玻璃增强热固塑料.第1部分:一般性( (Plastics piping systems
for underground drainage and sewerage under
pressure. Glass-reinforced thermosetting plastics
(GRP) based on unsaturated polyester resin (UP).
Part 1 : general.)
NF T57-214-3-1996 压力下地下排水系统用塑料管道系统.不饱和聚酯树脂基玻璃增强热固塑料.第3部分:配件
(Plastics piping systems for underground drainage
and sewerage under pressure. Glass-reinforced
thermosetting plastics (grp) based on unsaturated
polyester resin (up). Part 3 : fittings.)
NF T57-214-5-1996 压力下地下排水系统用塑料管道系统.不饱和聚酯树脂基玻璃增强热固塑料.第5部分:接头的适用性
(Plastics piping systems for underground drainage
and sewerage under pressure. Glass-reinforced
thermosetting plastics (grp) based on unsatured
polyester resin (up). Part 5: fitness for purpose
of the joints.)
NF T57-221-1996 塑料管道系统.玻璃纤维增强热固塑料管和配件.短期内部压力下管壁密封性的检验的试验方法
(Plastics piping systems. Glass-reinforced thermosetting
plastics (grp) pipes and fittings. Test methods
to prove the leaktightness of the wall under
short-term internal pressure.)
NF T57-227-1997 塑料管道系统.玻璃增强热固性塑料(GRP)管.周期性内部压力影响的试验方法
(Plastics piping systems. Glass-reinforced thermosetting
plastics (GRP) pipes. Test method for the effects
of cyclic internal pressure.)
NF T60-191-1993 石油产品和润滑脂.润滑脂存储时的脱油现象.压力下的静态条件
(Petroleum products and lubricating greases.
Oil separation on storage of grease. Static
conditions under pressure.)
NF T70-516-1995 军用高能材料.安全、易损坏性.真空状态下压力计化学兼容性的研究
(ENERGETIC MATERIALS FOR DEFENSE. SAFETY, VULNERABILITY.
STUDY OF CHEMICAL COMPATIBILITY BY VACUUM STABILITY
WITH MANOMETER.)
NF T70-631-6-2003 民用爆炸物.烈性炸药.第6部分:耐液体静压力的测定
(Explosives for civil uses - High explosives
- Part 6 : determination of resistance to hydrostatic
pressure.)
NF T72-320-1977 家用灭蝇剂.压力散布杀虫剂(烟雾型).效果指数的测定 (INSECTICIDES
FOR FLYING INSECTS. INSECTICIDE DISTRIBUTED
UNDER PRESSURE (“AEROSOL“ TYPE). DETERMINATION
OF THE EFFICIENCY RATING.)
NF T81-101-1975 液态化学制品和带1６型旋转同步额定压力的烃类对称半接头(吉尔曼体系)(ＧＵＩＬＬＥＭＩＮ)的运输和装卸
(TRANSPORT AND HANDLING OF LIQUID CHEMICAL PRODUCTS
AND HYDROCARBONS-HALF SYMETRIC COUPLING(GUILLEMIN
SYSTEM)WITH ROTATING LOCK-NOMINALPRESSURE 16.)
NF T81-103-1980 液态体化学产品的运输和装卸.底部注入或排放的罐车.内部关闭阀和安全阀.使用压力等于或小于４巴
(TRANSPORTATION AND HANDLING OF LIQUID CHEMICAL
PRODUCTS. TANKER VEHICLES FILLED AND EMPTIED
FROM BELOW. INTERNAL SAFETY AND STOP VALVE.
OPERATING PRESSURE EQUAL TO OR LESS THAN 4 BAR.)
NF T81-104-1981 液态体化学产品的运输和装卸.底部注入或排放的罐车.４－４０bar工作压力用标准尺寸ＤＮ８０和ＤＮ１００的
(TRANSPORTATION AND HANDLING OF LIQUEFIED GASES.
TANKER VEHICULES FILLED AND EMPTIED FROM BELOW.
INTERNAL SAFETY GATES DN 80 AND DN 100 FOR OPERATING
PRESSURES BETWEEN 4 BAR AND 40 BAR.)
NF T81-106-1976 喷雾状产品的运输.最大压力２．５bar气动排空的道路罐车.接头
(TRANSPORTATION OF POWDERY PRODUCTS. ROAD TANKERS
WITH PNEUMATIC DISCHARGE UNDER MAXIMUM PRESSURE
2.5 BAR. COUPLING.)
NF T81-202-1979 运输与装卸.货车和罐车.液化气或溶解气下部压力注入与排放的固定位置
(TRANSPORT AND HANDLING. RAIL CARS AND ROAD
TANKERS. PERMANENT STATIONS FOR BOTTOM LOADING
AND UNLOADING OF PRESSURIZED LIQUEFIED OR DISSOLVED
GASES.)
NF U16-101-1984 农用拖车.套管筒式单动作抓斗式起重拖车.系列25进气压力表(MPa)
(250bar2,3 型.互换尺寸 (AGRICULTURAL TRAILERS. SINGLE-ACTING
TELESCOPIC TIPPING CYLINDERS. 25 MPA (250 BAR)
SERIES. TYPLES 1,2 AND 3. INTERCHANGEABILITY
DIMENSIONS.)
NF U26-132-1985 植物保护装置.农药喷洒机具.喷雾器.喷嘴和压力计的连接尺寸
(EQUIPMENT FOR CROP PROTECTION. SPRAYERS. CONNECTING
DIMENSIONS FOR NOZZLES AND MANOMETERS.)
NF V03-743-1998 谷类.油籽和豆类.堆积谷物一维空气流通中单位压力损失的测定
(Cereals, oilseeds and pulses. Measurement of
unit pressure loss in one-dimensional air flow
through bulk grain.)
NF X10-520-1974 真空技术.工业真空系统中压力的测量 (VACUUM TECHNOLOGY-PRESSURE
MEASUREMENT IN INDUSTRIAL VACUUM SYSTEMS)
NF X10-521-1976 真空技术.压力计校准.直接比较法 (VACUUM TECHNOLOGY.
VACUUM GAUGES. CALIBRATION. METHOD BY DIRECT
COMPARISON.)
NF X10-522-1976 真空技术.电离压力计.校准.直接比较法 (VACUUM
TECHNOLOGY. IONIZATION VACUUM GAUGES. CALIBRATION
BY DIRECT COMPARISON.)
NF X10-523-1972 真空技术.低压压力计校准的一般方法 (VACUUM TECHNOLOGY.GENERAL
METHODS FOR LOW PRESSURE GAUGE CALIBRATION)
NF X10-524-1976 真空技术.压力计.校准.动力学法 (VACUUM TECHNOLOGY.
VACUUM GAUGES. CALIBRATION. DYNAMIC METHOD.)
NF X42-135-2001 生物技术.容器的性能标准.第3部分:玻璃压力容器 (Biotechnology
- Performance criteria for vessels - Part 3
: glass pressure vessels.)
NF X45-302-2000 过滤盒.试验方法.不同压力对流率的测定 (Filter
cartridges - Test methods - Determination of
differential pressure versus flowrate.)
XP T54-034-1999 塑料.在液态食物,热水,工业用液体压力下传输用未增塑聚(氯乙烯)(PVC-U)管道.增压液体用减速规则的制定和规
(Plastics - Unplasticized poly(vinyl chloride)
(PVC-U) piping for conveyance under pressure
of liquid foodstuffs, thermal water and industrial
liquids - Specifications and setting of the
derating rules for pressurized liquids.)
|
管件知识
