国内外接头标准
joint standards
美国接头标准(ANSI joint standards)
--------------------------------------------------------------------------------
编号 中文名称 英文名称
ANSI B5.11-1964 多轴钻头用轴头和可调接头 Spindle Noses and
Adjustable Adapters for Multiple Spindle Drilling
Heads
ANSI J-STD-002-1992 元件引线、接线端、焊片、接头和金属丝的软钎焊性试验
Solderability tests for component leads, terminations,
lugs, terminals and wires
ANSI PH3.101-1983 摄影(照相机).美国照相机用三角架接头(1/4英寸-20牙)
Photography (Cameras) - Tripod Connections for
American Cameras (1/4-Inch-20 Thread)
ANSI/API SPEC14L-2007 锁紧心轴和落地螺纹接头的规范 Specification
for Lock Mandrels and Landing Nipples
ANSI/ASAE S366.2-2004 农业拖拉机和机械.一般用途快速液压接头 Agricultural
tractors and machinery - General purpose quick-action
hydraulic couplers
ANSI/ASME A112.18.3-2002 泵固定件接头中防回流装置和系统的性能要求
Performance Requirements for Backflow Protection
Devices and Systems in Plumbing Fixture Fittings
ANSI/ASME B107.2-2002 电动冲击式延伸、接合及万向接头套筒扳手(英制)
Socket Wrenches, Extensions, Adaptors, and Universal
Joints, Power Drive (Impact) (Inch Series)
ANSI/ASME MFC-3Ma-2007 用孔板、管接头和文杜利管测量管道中的液体流量
Measurement of Fluid Flow in Pipes Using Orifice,
Nozzle and Venturi
ANSI/ASTM D2609-2002 聚乙烯塑料管塑料插入接头规范 Specification
for Plastic Insert Fittings for Polyethylene
(PE) Plastic Pipe
ANSI/ASTM D2672a-1996 使用溶解粘固剂的IPS PVC管用接头规范
Specification for Joints for IPS PVC Pipe Using
Solvent Cement
ANSI/ASTM D3138-2004 丙烯腈-丁二烯-苯乙烯共聚物和聚氯乙烯无压管道系统构件之间转换接头用液状粘固剂规范
Specification for Solvent Cements for Transition
Joints between Acrylonitrile-Butadiene-Styrene
(ABS) and Poly(Vinyl Chloride) (PVC) Non-Pressure
Piping Components
ANSI/ASTM D3212-2007 使用软质人造橡胶密封料制塑料排水管和污水管用接头的规范
Specification for Joints for Drain and Sewer
Plastic Pipes Using Flexible Elastomeric Seals
ANSI/ASTM D5677-2005 用于航空喷气机涡轮燃料的玻璃纤维(玻璃纤维加固热硬化树脂)管与管件规范.粘合剂粘接接头型
Specification for Fiberglass (Glass-Fiber-Reinforced
Thermosetting-Resin) Pipe and Pipe Fittings,
Adhesive Bonded Joint Type, for Aviation Jet
Turbine Fuel Lines
ANSI/ASTM F1365-1991 采用柔性合成橡胶密封件的塑料地下管道接头耐水渗透性试验方法
Test Method For Water Infiltration Resistance
Of Plastic Underground Conduit Joints Which
Use Flexible Elastomeric Seals
ANSI/ASTM F1429-1999 用柔性合成橡胶密封件固定在套桶中的塑料地下管道接头组合力试验方法
Test Method For Assembly Force Of Plastic Underground
Conduit Joints That Use Flexible Elastomeric
Seals Located In The Bell
ANSI/ASTM F1986-2001 冷热饮用水系统用2型多层管压合配件和压合接头的规范
Specification for Multilayer Pipe Type 2, Compression
Fittings, and Compression Joints for Hot and
Cold Drinking-water Systems
ANSI/ASTM F1987-2001 循环加热系统用2型多层管、压合配件和压合接头的规范
Specification for Multilayer Pipe Type 2, Compression
Fittings, and Compression Joints for Hydronic
Heating Systems
ANSI/ASTM F2014-2000 管道非增强挤制T形接头规范 Specification
for Non-Reinforced Extruded Tee Connections
for Piping Applications
ANSI/ASTM F2634-2007 用拉力冲击法的聚乙烯(PE)熔接接头的实验室测试用试验方法
Test Method for Laboratory Testing of Polyethylene(pe)
Butt Fusion Joints Using Tensile-impact Method
ANSI/ASTM F682a-1982 锻制碳素钢套管接头规范 Specification
for Wrought Carbon Steel Sleeve-type Pipe Couplings
ANSI/ASTM F704-1997 管道系统法兰接头用螺栓长度的选用惯例 Practice
for Selecting Bolting Lengths for Piping System
Flanged Joints
ANSI/ASTM F722-1982 船上管道系统用焊接接头规范 Specification
for Welded Joints for Shipboard Piping Systems
ANSI/ASTM F905-2004 聚乙烯鞍形熔融接头合格鉴定的实施规范 Practice
for Qualification of Polyethylene Saddle Fusion
Joints
ANSI/AWS C3.2M/C 3.2-2008 评定硬钎焊接头强度的标准方法 Standard
Methods for Evaluating the Strength of Brazed
Joints
ANSI/AWS D14.4/D 14.4M-2005 机械和设备焊接接头规范 Specification
for Welded Joints in Machinery and Equipment
ANSI/AWWA C111-2006 韧性铸铁压力管和配件的橡胶垫接头 Rubber-Gasket
Joints for Ductile-Iron Pressure Pipe and Fittings
ANSI/CSA LC7-2009 管接头密封化合物和材料 Pipe Joint Sealing
Compounds and Materials
ANSI/EIA 364-07B-1998 电连接件.压合接头变形试验程序 Electric
Connectors - Crimp Contact Deformation Test
Procedure
ANSI/EIA 5150000-1986 光学纤维和光缆接头的一般规范 Generic
Specification for Optical Fiber and Cable Splices
ANSI/EIA 540ABAA-1991 引线间隙为0.635mm(0.25英寸)的塑料方形平接头用片载插孔的详细规范
Detail Specification for Chip Carrier Sockets
for Plastic Quad Flat Pack 0.635-mm (0.25-in)
Lead Spacing (Gullwing)
ANSI/EIA 540ADAA-1992 电子设备用针状格子排列插孔的适配器-载体方形平接头的详细规范
Adaptor-Carrier Quad Flat Pack to Pin Grid Array
Sockets for Use in Electronic Equipment, Detail
Specification for
ANSI/EIA 677-1997 小型电源接头销尺寸规范 Specification
for Small Form Factor Power Connector Pin Dimensions
ANSI/EIA-364-93-2009 电气连接器用绝缘置换触点(IDC)的重复线接头和断开试验程序
Repeated Wire Connection and Disconnection Test
Procedure for Insulation Displacement Contacts
(IDC) for Electrical Connectors
ANSI/IEEE 1511-2004 额定电压为5kV至46 kV的系统上电力电缆、接头和终端故障的调查和分析指南
Guide for Investigating and Analyzing Power
Cable, Joint, and Termination Failures on Systems
Rated 5kV Through 46 kV
ANSI/IEEE 404-2006 额定电压为2500-500000V的挤压介质电缆接头和层压介质电缆接头
Standard for Extruded and Laminated Dielectric
Shielded Cable Joints Rated 2500 V - 500 000
V
ANSI/IEEE 592-2007 高压电缆接头和可拆分连接器用暴露半导体护套的标准
Standard for Exposed Semiconducting Shields
on High Voltage Cable Joints and Separable Connectors
ANSI/ISO 5675-1992 农业拖拉机和机械.一般用途快速液压接头 Agricultural
tractors and machinery - General purpose quick-action
hydraulic couplers
ANSI/SAE J1036-1993 农用拖拉机圆柱形液压系统管接头的尺寸标准 Dimensional
Standard for Cylindrical Hydraulic Couplers
for Agricultural Tractors
ANSI/SAE J512-1994 汽车管接头 Fittings, Automotive
Tube
ANSI/SAE J513-1994 制冷用管接头(ANSI/SAE J513F的修订版)
Refrigeration Tube Fittings
ANSI/SAE J518-1993 四螺栓拼合法兰型液压法兰管、管道及软管接头 Hydraulic
Flanged Tube, Pipe, and Hose Connections, Four-Bolt
Split Flange Type
ANSI/SAE J530-1994 汽车管件接头 Automotive Pipe Fittings
ANSI/SCTE 116-2006 5/8-24端口、内螺纹接头的规范 Specification
for 5/8-24 Port, Female Adapters
ANSI/SCTE 59-2003 电介质接头上的中心对接 Center Conductor
Bond to Dielectric Bond
ANSI/TIA-455-8-2000 使用光时域反射计(OTDR)测量接头损耗或连接器损耗和反射比
Measurement of Splice or Connector Loss and
Reflectance Using an OTDR
ANSI/TIA/EIA 102BAAA-1-1999 项目25， FDMA共用气体管道接头，补充件1
Project 25 FDMA Common Air Interface Addendum
1
ANSI/UL 181-2008 工厂制通风管和通风管接头的安全标准 Standard
for Safety for Factory-Made Air Ducts and Air
Connectors
ANSI/UL 181B-2008 与柔性风管和风管接头一起使用的密闭系统的安全标准 Standard
for Safety for Closure Systems for Use With
Flexible Air Ducts and Air Connectors
ASME B16.29-2001 DWV类可锻铜和可锻铜合金钎焊连接排水管接头 (Wrought
copper and wrought copper alloy solder joint
drainage fittings - DWV)
ASME B16.39-1998 可锻铁螺纹管活接头:等级150、250和300 (Malleable
iron threaded pipe unions; Classes 150, 250,
and 300)
ASME MFC-3M Errata-1990 用孔板,管接头和文丘里管测量管道中的流量.正误表
(Measurement of fluid flow in pipes using orifice,
nozzle, and Venturi; Errata)
ASME MFC-3M-1989 用孔板,管接头和文丘里管测量管道中的液体流量. (Measurement
of fluid flow in pipes using orifice, nozzle,
and Venturi)
ASTM A865/A865M-2006 钢管连接用黑色或镀锌(电镀)焊接或无缝钢螺纹接头标准规范
Standard Specification for Threaded Couplings,
Steel, Black or Zinc-Coated (Galvanized) Welded
or Seamless, for Use in Steel Pipe Joints
ASTM B687-1999(2005)e1 镀黄铜、镀铜和镀铬管接头标准规范 Standard
Specification for Brass, Copper, and Chromium-Plated
Pipe Nipples
ASTM C443M-2007 用橡胶垫圈(米制)的混凝土管道和检修孔用接头的标准规范
Standard Specification for Joints for Concrete
Pipe and Manholes, Using Rubber Gaskets (Metric)
ASTM C505-2005a 带橡胶垫圈接头的无钢筋混凝土灌溉水管标准规范 Standard
Specification for Nonreinforced Concrete Irrigation
Pipe with Rubber Gasket Joints
ASTM C505M-2005a 带橡胶垫圈接头的无钢筋混凝土灌溉水管标准规范(米制)
Standard Specification for Nonreinforced Concrete
Irrigation Pipe With Rubber Gasket Joints [Metric]
ASTM D1101-1997a(2006) 室外用层压结构木制品的胶合接头完整性的标准试验方法
Standard Test Methods for Integrity of Adhesive
Joints in Structural Laminated Wood Products
for Exterior Use
ASTM D2855-1996(2002) 聚氯乙烯管和配件的溶剂粘固接头制作的标准实施规程
Standard Practice for Making Solvent-Cemented
Joints with Poly(Vinyl Chloride) (PVC) Pipe
and Fittings
ASTM D2918-1999(2005) 受撕裂应力的胶粘接头耐用性的标准试验方法 Standard
Test Method for Durability Assessment of Adhesive
Joints Stressed in Peel
ASTM D3138-2004 丙烯腈-丁二烯-苯乙烯共聚物和聚氯乙烯无压管道系统构件之间转换接头用液态粘结剂的标准规范
Standard Specification for Solvent Cements for
Transition Joints Between Acrylonitrile-Butadiene-Styrene
(ABS) and Poly(Vinyl Chloride) (PVC) Non-Pressure
Piping Components
ASTM D3164-2003 用拉伸负荷法测定胶粘剂粘接塑料搭接接头剪切强度特性的标准试验方法
Standard Test Method for Strength Properties
of Adhesively Bonded Plastic Lap-Shear Sandwich
Joints in Shear by Tension Loading
ASTM D3164M-2003 用拉伸负荷法测定胶粘剂粘接塑料搭接接头剪切强度性能的试验方法(米制)
Standard Test Method for Strength Properties
of Adhesively Bonded Plastic Lap-Shear Sandwich
Joints in Shear by Tension Loading
ASTM D3212-2007 使用弹性柔性密封料制塑料排水管和污水管用接头的标准规范
Standard Specification for Joints for Drain
and Sewer Plastic Pipes Using Flexible Elastomeric
Seals
ASTM D3433-1999(2005) 粘结接头中胶粘剂的断裂强度的标准试验方法 Standard
Test Method for Fracture Strength in Cleavage
of Adhesives in Bonded Metal Joints
ASTM D3632-1998(2004) 用氧压法加速粘结接头老化的试验方法 Standard
Test Method for Accelerated Aging of Adhesive
Joints by the Oxygen-Pressure Method
ASTM D4161-2001(2005) 使用挠性弹性体密封件的"玻璃钢"(玻璃纤维增强热固树脂)管接头标准规范
Standard Specification for "Fiberglass"
(Glass-Fiber-Reinforced Thermosetting-Resin)
Pipe Joints Using Flexible Elastomeric Seals
ASTM D4502-1992(2004) 木材粘结接头耐热和耐水性的标准试验方法 Standard
Test Method for Heat and Moisture Resistance
of Wood-Adhesive Joints
ASTM D5249-1995(2006) 硅酸盐水泥混凝土和地沥青接头加热和制冷接缝密封胶衬垫材料的标准规范
Standard Specification for Backer Material for
Use with Cold- and Hot-Applied Joint Sealants
in Portland-Cement Concrete and Asphalt Joints
ASTM D5656-2004e1 拉伸载荷法测定剪切中胶粘剂应力-应变性能用厚被粘物金属搭接-剪切接头的标准试验方法
Standard Test Method for Thick-Adherend Metal
Lap-Shear Joints for Determination of the Stress-Strain
Behavior of Adhesives in Shear by Tension Loading
ASTM D6383-1999(2005) 由EPDM屋顶膜材料制造的胶粘剂接头的失效时间(蠕变破裂)的标准操作规程
Standard Practice for Time-to-Failure (Creep-Rupture)
of Adhesive Joints Fabricated from EPDM Roof
Membrane Material
ASTM D7174-2005 混凝土面层和结构建造用预制闭孔聚烯烃伸缩接头填充料的标准规范
Standard Specification for Preformed Closed-Cell
Polyolefin Expansion Joint Fillers for Concrete
Paving and Structural Construction
ASTM E677-1994(2004) 可互换的圆球形接头 Standard Specification
for Interchangeable Spherical Ground Joints
ASTM F1674-2005 与PVC管一起使用的接头约束装置的标准试验方法 Standard
Test Method for Joint Restraint Products for
Use with PVC Pipe
ASTM F1986-2001(2006) 冷热饮用水系统用2型多层管、压合配件和压合接头的标准规范
Standard Specification for Multilayer Pipe Type
2, Compression Fittings, and Compression Joints
for Hot and Cold Drinking-Water Systems
ASTM F2014-2000(2006) 管道系统用非增强挤制T形接头标准规范 Standard
Specification for Non-Reinforced Extruded Tee
Connections for Piping Applications
ASTM F2634-2007 通过拉力冲击法实验室测试聚乙烯(PE)熔接接头的用标准试验方法
Standard Test Method for Laboratory Testing
of Polyethylene (PE) Butt Fusion Joints using
Tensile-Impact Method
ASTM F905-2004 聚乙烯鞍形熔融接头的合格证明的标准实施规程 Standard
Practice for Qualification of Polyethylene Saddle-Fused
Joints
IEEE 404-2000 额定电压2500V-500000V的挤压和层压介质铠装电缆接头
(Extruded and laminated dielectric shielded
cable joints rated 2500 V to 500000 V)
IEEE 592-1990 高压电缆接头和可分离绝缘连接器的外露半导体护套 (Exposed
semiconducting shields on high-voltage cable
joints and separable insulated connectors)
UL 1363-1996 重新配置的临时电源接头 (Relocatable temporary
power taps )
UL 194-1996 防火用球墨铸铁和灰铸铁压力管和配件加垫圈的接头 (Gasketed
joints for ductile-iron pipe and fittings for
fire protection service )
UL 218A-2004 柴油机中驱动离心点火泵用电池接头标准 (Standard for
battery contactors for use in diesel engines
driving centrifugal fire pumps )
UL 310-2003 电气快速联接接头 (Electrical quick-connect
terminals)
UL 498A-1999 电流分接头和适配器 (Current taps and adapters
)
UL 860-2001 易燃和可燃流体与消防用管接头 (Pipe unions for
flammable and combustible fluids and fire-protection
service )
英国接头标准(BS joint standards)
--------------------------------------------------------------------------------
编号 中文名称 英文名称
BS 1560-3.2-1989 管子、阀门和接头(规定等级)用圆法兰.第3部分:钢、铸铁和铜合金法兰.第2节:铸铁法兰规范
Circular flanges for pipes, valves and fittings
(Class designated) - Steel, cast iron and copper
alloy flanges - Specification for cast iron
flanges
BS 1782-1951 消防软管接头除外的吸入软管和送水软管接头(1.5英寸至8英寸标称尺寸)规范
Specification for couplings for suction and
delivery hose (11/2 in. to 8 in. nominal sizes)
other than fire hose couplings
BS 1906-1952 (标称尺寸1/8英寸-1/4英寸）软管接头(露天和水中使用)规范
Specification for hose couplings (air and water)
(1/8 in. to 11/4 in. nominal sizes)
BS 2051-1-1973 工程用管与管接头规范.第1部分:工程用铜与铜合金毛细管与耐压管接头
Tube and pipe fittings for engineering purposes
- Copper and copper alloys capillary and compression
tube fittings for engineering purposes
BS 2051-2-1984 工程用管与管接头规范.第2部分:橄榄型铜合金耐压管接头 Tube
and pipe fittings for engineering purposes -
Specification for olive type copper alloy compression
tube fittings
BS 2464-1954 汽油、石油和润滑剂用软管接头(标称尺寸 1/4英寸至 4英寸)规范
Specification for hose couplings for petrol,
oil and lubricants (3/4 in. to 4 in. nominal
sizes)
BS 2464-2-1969 石油、汽油和润滑油用软管接头规范.第2部分:高压接头 Specification
for hose couplings for petrol, oil and lubricants
- High pressure couplings
BS 2464-3-1968 汽油、石油和润滑剂用软管接头规范.第3部分:快速接头 Specification
for hose couplings for petrol, oil and lubricants
- Quick-acting couplings
BS 2464-4-1980 汽油、石油和润滑剂用软管接头规范.第4部分:欧洲型 100mm快速接头规范
Hose couplings for petrol, oil and lubricants
- Specification for 100 mm quick-acting couplings:
European type
BS 2761-1983 球面接头规范 Specification for spherical
ground joints
BS 2782-11 Method 1108A-1989 塑料试验方法.第11部分:热塑性塑料管、接头和阀门.试验方法1108A:管界面限定碰撞率
Methods of testing plastics - Thermoplastics
pipes, fittings and valves - True impact rate
(TIR) boundaries of pipes
BS 2782-11 Method 1109A-1989 塑料试验方法.第11部分:热塑性塑料、接头和阀门.试验方法1109A:非承压聚乙烯管和接头耐坏境应力开裂性
Methods of testing plastics - Thermoplastics
pipes, fittings and valves - Resistance to environmental
stress cracking of polyethylene pipes and fittings
for non-pressure applications
BS 2782-11 Method 1121B-1997 塑料的试验方法.第11部分:热塑管、接头和阀门.流体输送用热塑管.试验方法1121B:额定外部直径和额定压力.米
Methods of testing plastics - Thermoplastics
pipes, fittings and valves - Thermoplastics
pipes for the conveyance of fluids - Nominal
outside diameters and nominal pressures - Metric
series
BS 2782-11 Method 1121C-1997 塑料试验方法.第11部分:热塑管、接头和阀门.流体输送用热塑管.试验方法1121C:额定外部直径和额定压力.英尺
Methods of testing plastics - Thermoplastics
pipes, fittings and valves - Thermoplastics
pipes for the conveyance of fluids - Nominal
outside diameters and nominal pressures - Inch-based
series
BS 2782-11 Method 1121H-1996 塑料试验方法.第11部分:热塑性塑料管、接头和阀门.试验方法1121H:非承压液体输送热塑性塑料管.管头损失计算
Methods of testing plastics - Thermoplastics
pipes, fittings and valves - Thermoplastics
pipes for the transport of liquids under pressure
- Calculation of head losses
BS 2C 4-1973 飞机发动机制冷剂压力灌注接头尺寸规范 Specification
for coupling dimensions for aero-engine refrigerant
pressure replenishment connections
BS 2C 5-1976 液氧灌注连接头配合尺寸规范 Specification for
mating dimensions for liquid oxygen replenishment
couplings
BS 2M 53-1997 飞机.液压系统.管道和管接头热冲击试验 Aircraft -
Fluid systems - Thermal shock testing of piping
and fittings
BS 2SP 101-104-1956 飞行器用旋转套筒、张力传动杆和旋压钢索端部接头(统一螺纹)规范
Specifications for turnbarrels, tension rods
and swaged cable-end connections (Unified threads)
for aircraft
BS 2SP 7-1943 飞机材料规范.叉形接头(高强度型)(尺寸号 4B.A.至<1/4>英寸B.S.F
Specification for aircraft material - Fork joints
(high tensile type) (for sizes No. 4 B.A. to
3/4 inch B.S.F. inclusive)
BS 31-1940 电气布线用钢导线管和管接头 Specification - Steel
conduit and fittings for electrical wiring
BS 3288-3-1989 架空电力导线绝缘和导线接头.第3部分:绝缘子组件球窝连接接头尺寸
Insulator and conductor fittings for overhead
power lines - Dimensions of ball and socket
couplings of string insulator units
BS 336-1989 消防软管接头与辅助设备的规范 Specification for
fire hose couplings and ancillary equipment
BS 341-3-2002 可运输气体容器的阀门.阀门出口接头 Transportable
gas container valves - Valve outlet connections
BS 3799-1974 石油工业用钢管配件、螺旋管接头和套管焊接规范 Specification
for steel pipe fittings, screwed and socket-welding
for the petroleum industry
BS 3818-1964 柴油机车及有轨内燃机车自动密封加油接头规范 Specification
for self-sealing fuelling couplings for diesel
locomotives and diesel railcars
BS 3SP 3-1943 飞机材料规范.叉形接头(低强度型)(尺寸自N0.4B.A至<1/2>英寸B.S.F.)
Specification for aircraft material - Fork joints
(low tensile type) (for sizes No. 4 B.A. to
1/2 inch B.S.F. inclusive)
BS 4222-1967 牙科手持机的传动联轴器(滑配接头)尺寸规范 Specification
for dimensions of the transmission coupling
(slip-joint) to dental handpieces
BS 4368-4-1984 液压和通用压合管接头.第4部分:型号试验要求规范 Metallic
tube connectors for fluid power and general
use - Specification for type test requirements
BS 4568-1-1970 电气装置用ISO型米制螺纹钢导管及接头规范.第1部分:钢导管、弯头和接头
Specification for steel conduit and fittings
with metric threads of ISO form for electrical
installations - Steel conduit, bends and couplers
BS 4579-2-1973 电缆和电线连接器机械和压合接头性能规范.第2部分:镍、铁及镀铜导线压合接头
Specification for performance of mechanical
and compression joints in electric cable and
wire connectors - Compression joints in nickel,
iron and plated copper conductors
BS 4607-1-1984 电气装置用非金属导管及接头规范.第1部分:绝缘材料接头和元件规范
Non-metallic conduits and fittings for electrical
installations - Specification for fittings and
components of insulating material
BS 4607-5-1982 电气装置用非金属导管及接头规范.第5部分:绝缘材料刚性导管、接头和元件规范
Non-metallic conduits and fittings for electrical
installations - Specification for rigid conduits,
fittings and components of insulating material
BS 4622-1970 灰口铁管和管接头规范 Specification for grey
iron pipes and fittings
BS 4742-4-1985 农用机械液压设备.第4部分:挂车和机具用制动系统用液压管接头规范
Hydraulic equipment for agricultural machinery
- Specification for hydraulic couplings on braking
systems for trailers and trailed equipment
BS 4742-7-1989 农用机械液压设备.第7部分:农用拖挂车辆液压制动系统管接头用油口连接规范
Hydraulic equipment for agricultural machinery
- Specification for port connections for agricultural
trailed vehicle hydraulic brake couplings
BS 4871-3-1985 按认可焊接工艺操作的焊工鉴定考试规范.第3部分:金属管与管板接头间电弧焊
Specification for approval testing of welders
working to approved welding procedures - Arc
welding of tube to tube-plate joints in metallic
materials
BS 4G 178-2-1986 飞机电缆电线压接头.第2部分:压接检验规范(包括用户检验试验)
Crimped joints for aircraft electrical cables
and wires - Specification for control of crimping
(including user control tests)
BS 5200-1997 水管接头和转接器的尺寸规范 Specification for
dimensions of hydraulic connectors and adaptors
BS 534-1990 水和污水用钢管接头和异型管件规范 Specification for
steel pipes, joints and specials for water and
sewage
BS 5529-1988 工业用低压开关设备和控制装置规范.A型、直流用、3或4个接头的近距离电感开关
Specification for low-voltage switchgear and
controlgear for industrial use - Inductive proximity
switches - Form A, for direct current, 3 or
4 terminals
BS 5611-1978 负载分接头切换开关应用指南 Application guide
for on-load tap-changers
BS 5649-5-1982 路灯杆规范.第5部分:电气接头底座与电线敷设槽规范 Lighting
columns - Specification for base compartments
and cableways
BS 572-1985 互换式锥形毛玻璃接头规范 Specification for interchangeable
conical ground glass joints
BS 5911-1-2002 预制混凝土管、管配件和辅助制品.具有软接头的非加筋、加筋混凝土管(包括套管)和管配件规范(对
BS EN 1916: Concrete pipes and ancillary concrete
products - Specification for unreinforced and
reinforced concrete pipes (including jacking
pipes) and fittings with flexible joints(comnplementary
to BSEN 1916:2002)
BS 5911-5-2004 混凝土管和辅助混凝土制品.带软接头的预应力非压力管道和配件的规范
Concrete pipes and ancillary concrete products
- Specification for prestressed non-pressure
pipes and fittings with flexible joints
BS 6083-5-1984 助听器.第5部分:内插式耳机短接管接头和封闭装置尺寸规范
Hearing aids - Specification for dimensions
of the nipple and sealing device for insert
earphones
BS 6102-15-1991 自行车.第15部分:辐条螺纹接头尺寸规范 Cycles
- Specification for dimensions of spoke nipples
BS 6362-1990 按BS21 "带压密接合螺纹接头的管及配件管螺纹"
攻丝的不锈钢管规范 Specification for stainless steel
tubes suitable for screwing in accordance with
BS 21 'Pipe threads for tubes and fittings where
pressure-tight joints are made on the threads'
BS 6464-1984 制炼厂用增强塑料管、配件和接头规范 Specification
for reinforced plastics pipes, fittings and
joints for process plants
BS 65-1991 只用于地表水管道和配件的陶管、配件、导管和挠性机械接头规范 Specification
for vitrified clay pipes, fittings and ducts,
also flexible mechanical joints for use solely
with surface water pipes and fittings
BS 6537-1984 液压流体设备用U型接头规范 Specification for
staple type connectors for hydraulic fluid power
applications
BS 669-1-1989 燃气灶具用软管、管接头和承窩接口.第1部分:采用第1、2类燃气的家用灶具用带绕金属软管、护罩、接头配件和
Flexible hoses, end fittings and sockets for
gas burning appliances - Specification for strip-wound
metallic flexible hoses, covers, end fittings
and sockets for domestic appliances burning
1st and 2nd family gases
BS 669-2-1997 燃气灶具用软管、接头和管座.使用第1、2和3类燃气的家用灶具波纹金属软管、封盖、接头和管座规范
Flexible hoses, end fittings and sockets for
gas burning appliances - Specification for corrugated
metallic flexible hoses, covers, end fittings
and sockets for catering appliances burning
1st, 2nd and 3rd family gases
BS 6910-2-1989 电压范围为交流1000V和直流1500Vd.c.的低温浇注树脂复合物和热缩电缆接头.第2部分:现场安装实用规程
Cold pour resin compound and heat-shrink cable
joints in the voltage range up to 1000 V a.c.
and 1500 V d.c. Code of practice for on-site
installation
BS 746-2005+A1-2009 燃气表活接头与转接器用规范 Specification
for gas meter unions and adaptors
BS 7677-1993 管道接头用密封圈缺陷分类推荐标准 Recommendations
for classification of imperfections in pipe
joint rings
BS 778-1966 液压用钢管与接头规范 Specification for steel
pipes and joints for hydraulic purposes
BS 8407-2002 地下用输送带机械和叠接接头的规范 Specification
for mechanical and spliced joints in conveyor
belting for use underground
BS 864-2-1983 铜和铜合金制毛细管与承压管配件.铜管用毛细管与压合接头规范
Capillary and compression tube fittings of copper
and copper alloy. Specification for capillary
and compression fittings for copper tubes
BS 9522 N0001-1982 直流和低频用多触头圆形电气连接件详细规范、带有前面可释放后面可拆卸的压接触点卡口接头.全面评估级
Detail specification for multi-contact circular
electrical connectors for d.c. and low frequency
applications - Bayonet coupling with front release,
rear removable crimp contacts - Full assessment
level
BS 9522 N0003-1990 直流和低频用多触点圆形电气连接器详细规范.带后可插入、后释放、后可拆卸压接触点的无档板密封、耐环境影
Detail specification for multi-contact circular
electrical connectors for d.c. and low frequency
applications - Bayonet coupling non-barrier
sealed, environment resistant with rear insertable,
rear release, rear removable crimp contacts
also barrier sealed with non-removable solder
contact styles - Full plus airframe fit assessment
BS A 358-3-2000 MJ螺纹.流体系统用的接头的极限尺寸 MJ threads
- Limit dimensions for fittings for fluid systems
BS AU 91-1965 起动蓄电池圆锥形接线端子的电缆接头尺寸(用正极接地部件的汽车和轻便商用汽车)规范
Specification for dimensions of electrical cable
connectors for starter battery taper terminal
posts (cars and light commercial vehicles using
positive earth system)
BS DD CEN/TS 1591-3-2007 法兰及其连接件.垫圈的圆形法兰连接件用设计原则.第3部分:金属与金属接点之间的法兰接头的计算方法
Flanges and their joints - Design rules for
gasketed circular flange connections - Part
3: Calculation method for metal to metal contact
type flanged joint
BS DD CEN/TS 1591-4-2007 法兰及其连接件.垫圈的圆形法兰连接件用设计原则.第4部分:服从压力设备指令、符合设备螺栓接头装配要求的人
Flanges and their joints — Design rules for
gasketed circular flange connections — Part
4: Qualification of personnel competency in
the assembly of bolted joints fitted to equipment
subject to the Pressure Equipment Directive
BS EN 10253-1-1999 对接焊管道接头.通用和无特殊检验要求的锻制碳钢 Butt-welding
pipe fittings - Wrought carbon steel for general
use and without specific inspection requirements
BS EN 10253-2-2007 对接焊管道接头.带特殊检验要求的非合金和铁素体合金钢
Butt-welding pipe fittings — Part 2: Non alloy
and ferritic alloy steels with specific inspection
requirements
BS EN 10253-3-2008 对焊管接头.无特殊检验要求的锻制奥氏体和奥氏体-铁素体(二相)不锈钢
Butt-welding pipe fittings - Part 3: Wrought
austenitic and austenitic-ferritic (duplex)
stainless steels without specific inspection
requirements
BS EN 10253-4-2008 对焊管道接头.具有特殊检验要求的锻制奥氏体和铁素体－奥氏体(二相)不锈钢
Butt-welding pipe fittings - Part 4:Wrought
austenitic and austenitic-ferritic (duplex)
stainless steels with specific inspection requirements
BS EN 10311-2005 水和其他含水液体传送用钢管和配件的连接用接头 Joints
for the connection of steel tubes and fittings
for the conveyance of water and other aqueous
liquids
BS EN 1075-2000 木结构.试验方法.由冲打孔金属板紧固件构成的接头 Timber
structures - Test methods - Joints made with
punched metal plate fasteners
BS EN 1092-2-1997 法兰及其连接.按PN标注的管、阀门、管接头和附件的圆形安装法兰.第2部分:铸铁法兰
Flanges and their joints - Circular flanges
for pipes, valves, fittings and accessories,
PN designated - Cast iron flanges
BS EN 12308-1998 液化天然气设施和设备.用于液化天然气管道的法兰接头垫圈设计适配性试验
Installations and equipment for LNG - Suitability
testing of gaskets designed for flanged joints
used on LNG piping
BS EN 12316-1-2000 防水柔性板.接头抗剥离性的测定.屋顶防水沥青板 Flexible
sheets for waterproofing - Determination of
peel resistance of joints - Bitumen sheets for
roof waterproofing
BS EN 12316-2-2000 防水柔性板.接头抗剥离性的测定.屋顶防水用塑料和橡胶薄板
Flexible sheets for waterproofing - Determination
of peel resistance of joints - Plastic and rubber
sheets for roof waterproofing
BS EN 12317-1-2000 防水柔性板.屋顶防水沥青板.接头抗剪切性的测定 Flexible
sheets for waterproofing - Bitumen sheets for
roof waterproofing - Determination of shear
resistance of joints
BS EN 12512-2001 木结构.试验方法.机械紧固件接头的周期测试 Timber
structures - Test methods - Cyclic testing of
joints made with mechanical fasteners
BS EN 12517-2-2008 焊缝的无损检验.通过射线照相术评估铝及铝合金的焊接接头.验收等级
Non-destructive testing of welds - Part 2: Evaluation
of welded joints in aluminium and its alloys
by radiography - Acceptance levels
BS EN 1254-1-1998 铜和铜合金.管路接头.铜管毛细管钎焊法或铜焊法用端头接头
Copper and copper alloys - Plumbing fittings
- Fittings with ends for capillary soldering
or capillary brazing to copper tubes
BS EN 1254-2-1998 铜和铜合金.管路接头.与铜管一起使用的压合接头 Copper
and copper alloys - Plumbing fittings - Fittings
with compression ends for use with copper tubes
BS EN 1254-3-1998 铜和铜合金.管路接头.与塑料管一起使用的压合接头 Copper
and copper alloys - Plumbing fittings - Fittings
with compression ends for use with plastics
pipes
BS EN 1254-4-1998 铜和铜合金.管路接头.与带有毛细管或压力端头的其它端头连接的管接头
Copper and copper alloys - Plumbing fittings
- Fittings combining other end connections with
capillary or compression ends
BS EN 1254-5-1998 铜和铜合金.管路接头.铜管毛细管铜焊法用短端头接头
Copper and copper alloys - Plumbing fittings
- Fittings with short ends for capillary brazing
to copper tubes
BS EN 12560-1-2001 法兰及其接头.标示等级的法兰衬垫.有或无插孔的非金属水平衬垫
Flanges and their joints - Gaskets for Class-designated
flanges - Non-metallic flat gaskets with or
without inserts
BS EN 12560-2-2001 法兰及其接头.标示等级的法兰衬垫.钢法兰用螺旋缠绕衬垫
Flanges and their joints - Gaskets for Class-designated
flanges - Spiral wound gaskets for use with
steel flanges
BS EN 12560-3-2001 法兰及其接头.标示等级的法兰衬垫.非金属PTFE外壳衬垫
Flanges and their joints - Gaskets for Class-designated
flanges - Non-metallic PTFE envelope gaskets
BS EN 12560-4-2001 法兰及其接头.标示等级的法兰的衬垫.钢法兰用波纹状、水平或皱缩金属和填充金属衬垫
Flanges and their joints - Gaskets for Class-designated
flanges - Corrugated, flat or grooved metallic
and filled metallic gaskets for use with steel
flanges
BS EN 12560-5-2001 法兰及其接头.标示等级的法兰的衬垫.钢法兰用金属环接头衬垫
Flanges and their joints - Gaskets for Class-designated
flanges - Metallic ring joint gaskets for use
with steel flanges
BS EN 12560-7-2004 法兰及其接头.分级标示法兰用垫圈.钢法兰用涂覆金属的套层垫圈
Flanges and their joints - Gaskets for class-designated
flanges - Covered metal jacketed gaskets for
use with steel flanges
BS EN 12573-4-2000 焊接非静压热塑罐.法兰接头的设计和计算 Welded
static non-pressurized thermoplastic tanks -
Design and calculation of flanged joints
BS EN 1277-2004 塑料管道系统.地下无压用热塑性管道系统.弹性密封环型接头密封性的试验方法
Plastics piping systems - Thermoplastics piping
systems for buried non-pressure applications
- Test methods for leaktightness of elastomeric
sealing ring type joints
BS EN 12797-2000 铜焊.铜焊接头破坏试验 Brazing - Destructive
tests of brazed joints
BS EN 12799-2000 铜焊.铜焊接头无损检验 Brazing - Non-destructive
examination of brazed joints
BS EN 12814-1-2000 热塑性半成品焊接接头试验.弯曲试验 Testing
of welded joints of thermoplastics semi-finished
products - Bend test
BS EN 12814-2-2000 热塑半成品焊接接头试验.拉伸试验 Testing
of welded joints of thermoplastics semi-finished
products - Tensile test
BS EN 12814-3-2000 热塑半成品焊接接头试验.拉伸蠕变试验 Testing
of welded joints of thermoplastics semi-finished
products - Tensile creep test
BS EN 12814-4-2001 热塑半成品焊接接头试验.剥离试验 Testing
of welded joints of thermoplastics semi-finished
products - Peel test
BS EN 12814-5-2000 热塑半成品焊接接头试验.宏观检查 Testing
of welded joints of thermoplastics semi-finished
products - Macroscopic examination
BS EN 12814-6-2000 热塑半成品焊接接头试验.低温拉伸试验 Testing
of welded joints of thermoplastics semi-finished
products - Low temperature tensile test
BS EN 12814-7-2002 热塑性半成品的焊接接头的试验.腰形试验样品的拉伸试验
Testing of welded joints of thermoplastics semi-finished
products - Tensile test with waisted test specimens
BS EN 12814-8-2001 热塑半成品焊接接头试验.要求 Testing of
welded joints of thermoplastic semi-finished
products -. Requirements
BS EN 13090-2000 建筑物内气体管道的螺纹接头重新密封方法 Means for
resealing threaded joints of gas pipework in
buildings
BS EN 13100-1-2000 热塑性半成品焊接接头无损检验.目视检查 Non destructive
testing of welded joints of thermoplastics semi-finished
products - Visual examination
BS EN 13100-2-2004 热塑性半成品焊接接头的无损检验.X射线照相检验 Non
destrictive testing of welded joints of thermoplastics
semi-finished products - X-ray radiographic
testing
BS EN 13100-3-2004 热塑性半成品焊接接头的无损检验.超声检验 Non-destructive
testing of welded joints in thermoplastics semi-finished
products - Ultrasonic testing
BS EN 13271-2002 木材紧固件.连接器接头的特征载荷能力和滑脱系数 Timber
fasteners - Characteristic load-carrying capacities
and slip-moduli for connector joints
BS EN 14257-2006 粘合剂.木材粘合剂.温度升高时搭接接头拉伸强度的测定(WATT
'91) Adhesives - Wood adhesives - Determination
of tensile strength of lap joints at elevated
temperature (WATT '91)
BS EN 14258-2004 结构粘合剂.短期或长期暴露于特定温度条件下的粘合接头的机械性能
Structural adhesives - Mechanical behaviour
of bonded joints subjected to short and long
terms exposure at specified conditions of temperature
BS EN 1435-1997 焊缝的无损检验.焊接接头的放射性检验 Non-destructive
examination of welds - Radiographic examination
of welded joints
BS EN 144-3-2003 呼吸保护装置.气瓶阀.潜水用Nitrox和氧气气瓶的出口接头
Respiratory protective devices - Gas cylinder
valves - Outlet connections for diving gases
Nitrox and oxygen
BS EN 14454-2005 防饮用水回流污染的装置.软管接头防回流装置DN 15～DN
32.A型H系列 Devices to prevent pollution by backflow
of potable water - Hose union backflow preventer
DN 15 to DN 32 inclusive - Family H, type A
BS EN 14525-2005 不同材料管道用球墨铸铁大公差联接器和法兰接头:球墨铸铁、灰铸铁、钢、PVC-U、PE和纤维水泥
Ductile iron wide tolerance couplings and flange
adaptors for use with pipes of different materials:
ductile iron, grey iron, steel, PVC-U, PE, fibre-cement
BS EN 14741-2006 热塑管和管道系统.非压力掩埋用接头.通过评估密封压力测定弹性密封件接合处的长期密封性能的试验方法
Thermoplastics piping and ducting systems -
Joints for buried non-pressure applications
- Test method for the long-term sealing performance
of joints with elastomeric seals by estimating
the sealing pressure
BS EN 15096-2008 防饮用水回流污染用装置.软管接头防真空阀.包括B型和D型H系列的DN
15～DN 25.通用技术规范 Devices to prevent pollution
by backflow of potable water - Hose Union anti-vacuum
valves - DN 15 to DN 25 inclusive Family H,
type B and type D. General technical specification
BS EN 1515-1-2000 法兰及其接头.螺栓连接.螺栓连接的选择 Flanges
and their joints - Bolting - Selection of bolting
BS EN 15617-2009 焊接接头的无损检验.飞行时间衍射技术(TOFD).接受等级
Non-destructive testing of welds - Time-of-flight
diffraction technique (TOFD) - Acceptance levels
BS EN 1591-2-2008 法兰及其接头.带衬垫的环形法兰连接件的设计规则.垫圈参数
Flanges and their joints - Design rules for
gasketed circular flange connections - Part
2:Gasket parameters
BS EN 1741-1998 带有开放结构的蒸气加气混凝土或轻集料混凝土预制构件之间接头处非平面方向抗剪切强度的测定
Determination of shear strength for out-of-plane
forces of joints between prefabricated components
made of autoclaved aerated concrete or lightweight
aggregate concrete with open structure
BS EN 175201-804-2000 电子元器件质量评定协调系统.详细规范.环形连接器.螺纹接头直径1.6mm圆触点
Harmonized system of quality assessment for
electronic components - Detail specification
- Circular connectors - Round contacts, size
diameter 1,6 mm, threaded coupling
BS EN 1829-2-2008 高压喷水机器.安全要求.软管、软管管路和接头 High-pressure
water jet machines — Safety requirements — Part
2: Hoses, hose lines and connectors
BS EN 1993-1-8-2005 欧洲法规3.钢结构的设计.接头设计 Eurocode
3: Design of steel structures - Part 1-8: Design
of joints
BS EN 205-2003 胶粘剂.非结构用木材粘结剂.搭接接头拉力剪切强度的测量 Adhesives
- Wood adhesives for non-structural applications
- Determination of tensile shear strength of
lap joints
BS EN 21089-1992 点焊设备用电极锥度接头.尺寸 Electrode taper
fits for spot welding equipment - Dimensions
BS EN 2591-217-2002 电气和光学连接元件.试验方法.终端接线片和连机拼合接头在规定电流下的电压降
Elements of electrical and optical connection
- Test methods - Voltage drop under specified
current for terminal lugs and in-line splices
BS EN 2591-218-2002 电气和光学连接元件.试验方法.用温度和电流循环法试验终端接线片和连机拼合接头的衰老程度
Elements of electrical and optical connection
- Test methods - Ageing of terminal lugs and
in-line splices by temperature and current cycling
BS EN 2591-219-2002 电器和光学连接元件.试验方法.绝缘终端接线片和连机拼合接头的电压强度
Elements of electrical and optical connection
- Test methods - Voltage strength for insulated
terminal lugs and in-line splices
BS EN 2591-220-2005 航空航天系列.电和光学连接元件.试验方法.电流和温度周期性变化引起的触点/导体接头老化
Elements of electrical and optical connection
— Test methods — Part 220: Contact/conductor
joint ageing by current and temperature cycling
BS EN 2665-003-1999 额定电流为20A至50A的温度补偿的三极电路断路器.米制螺纹接头.产品标准
Circuit breakers, three-pole, temperature compensated,
rated currents 20 A to 50 A. Metric thread terminals
- Product standard
BS EN 2665-004-1999 额定电流为20A至50A的温度补偿的三极电路断路器.UNC螺纹接头.产品标准
Circuit breakers, three-pole, temperature compensated,
rated currents 20 A to 50 A. UNC thread terminals
- Product standard
BS EN 26891-1991 木结构.机械紧固件接头.强度和变形特性测定一般原则 Timber
structures - Joints made with mechanical fasteners
- General principles for the determination of
strength and deformation characteristics
BS EN 2794-003-1999 额定电流为20A至50A的温度补偿的单极电路断路器.米制螺纹接头.产品标准
Circuit breakers, single-pole, temperature compensated,
rated currents 20 A to 50 A. Metric thread terminals
- Product standard
BS EN 2794-004-1999 额定电流为20A至50A的温度补偿的单极电路断路器.UNC螺纹接头.产品标准
Circuit breakers, single-pole, temperature compensated,
rated currents 20 A to 50 A. UNC thread terminals
- Product standard
BS EN 28430-1-1992 点焊设备规程.电极夹具.第1部分:锥形接头锥度1:10
Specification for resistance spot welding -
Electrode holders - Taper fixing 1:10
BS EN 28430-2-1992 点焊设备规程.电极夹具.第2部分:莫氏锥形接头 Specification
for resistance spot welding - Electrode holders
- Morse taper fixing
BS EN 28970-1991 木结构.用机械紧固件连接的接头试验.木材致密度要求 Timber
structures - Testing of joints made with mechanical
fasteners - Requirements for wood density
BS EN 295-1-1991 排水管和下水道用陶管和管配件及管接头.要求 Vitrified
clay pipes and fittings and pipe joints for
drains and sewers - Requirements
BS EN 295-2-1991 排水管和下水道用陶管和管配件及管接头.质量控制和抽样
Vitrified clay pipes and fittings and pipe joints
for drains and sewers - Quality control and
sampling
BS EN 295-3-1991 排水管和下水道用陶管和管配件及管接头.试验方法 Vitrified
clay pipes and fittings and pipe joints for
drains and sewers - Test methods
BS EN 295-4-1995 排水管和下水道用陶制管和管配件及管接头.专用配件、管接头和配套附件的要求
Vitrified clay pipes and fittings and pipe joints
for drains and sewers - Requirements for special
fittings, adaptors and compatible accessories
BS EN 295-5-1994 排水管和下水道用陶管和管配件及管接头.带孔的陶管及配件的要求
Vitrified clay pipes and fittings and pipe joints
for drains and sewers - Requirements for perforated
vitrified clay pipes and fittings
BS EN 295-6-1996 排水管和污水管用陶制管、管件及管接头.陶制管人孔的要求
Vitrified clay pipes and fittings and pipe joints
for drains and sewers - Requirements for vitrified
clay manholes
BS EN 295-7-1996 排水管和污水管用陶制管、管件及管接头.陶制管和管插接接头的要求
Vitrified clay pipes and fittings and pipe joints
for drains and sewers - Requirements for vitrified
clay pipes and joints for pipe jacking
BS EN 3079-2006 8°30'压力＜28000kPa的导管接头.适配器.米制系列.技术规范
Pipe coupling 8 °30' up to 28000 kPa - Adaptors
- Metric series - Technical specification
BS EN 3082-2001 航空航天系列.钛合金管连接件8°30'.修理用闷头焊接活接头
Aerospace series - Pipe coupling 8 °30' in titanium
alloy - Unions, bulkhead welded, for repair
BS EN 3083-2001 航空航天系列.钛合金管连接件8°30'.修理用闷头长焊接端头活接头
Aerospace series - Pipe coupling 8 °30' in titanium
alloy - Unions, bulkhead, long welded end, for
repair
BS EN 3084-2001 航空航天系列.钛合金管连接件8°30'.修理用焊接端头螺纹活接头
Aerospace series - Pipe coupling 8 °30' in titanium
alloy - Unions, welded end threaded for repair
BS EN 3244-2001 航空航天系列.钛合金8°30’管连接件.双端头的活接头
Aerospace Series - Pipe coupling 8 °30' in titanium
alloy - Unions, double ended
BS EN 3245-2001 航空航天系列.钛合金8°30'管连接件.变径活接头 Aerospace
series - Pipe coupling 8 °30' in titanium alloy
- Unions, reducer
BS EN 3246-2001 航空航天系列.钛合金8°30' 管连接件.、闷头活接头
Aerospace series - Pipe coupling 8 °30' in titanium
alloy - Unions, bulkhead
BS EN 3247-2001 航空航天系列.钛合金8°30'管连接件.闷头焊接端活接头、
Aerospace series - Pipe coupling 8 °30' in titanium
alloy - Unions, bulkhead welded end
BS EN 3248-2001 航空航天系列.钛合金管连接件8°30’.带锁紧装置的缩径管端的转接头
Aerospace series - Pipe coupling 8 °30' in titanium
alloy - Adaptors, reduced pipe end, with lockring
BS EN 3373-001-2007 航空航天系列.电导体压接用终端盒和内嵌式接头.第001部分:技术规范
Aerospace series — Terminal lugs and in-line
splices for crimping on electric conductors
— Part 001: Technical specification
BS EN 3373-010-2009 航空航天系列.电导体压接用终端盒和内嵌式接头.米制和英制螺栓系列用温度低于150℃铜导体压接用镀锡环型终
Aerospace series - Terminal lugs and in-line
splices for crimping on electric conductors
- Terminal lugs, ring shaped, tin plated, for
crimping on copper conductors, temperature up
to 150 °C for metric and inch stud series -
Product standard
BS EN 3373-011-2009 航空航天系列.电导体压接用终端盒和内嵌式接头.米制和英制螺柱系列用温度小于260℃、铜导体压接用镀镍环形
Aerospace series - Terminal lugs and in-line
splices for crimping on electric conductors
- Terminal lugs, ring shaped, nickel plated,
for crimping on copper conductors, temperature
up to 260 °C for metric and inch stud series
- Product standard
BS EN 3373-012-2005 电导体压接用终端盒和内嵌式接头.第012部分:温度小于150℃铜导体压接用绝缘和密封的内嵌式接头.产品标准
Terminal lugs and in-line splices for crimping
on electric conductors - Part 012: In-line splices,
insulated and sealed, for crimping on copper
conductors, temperature up to 150 ℃ - Product
standard
BS EN 3373-013-2005 电导体压接用终端盒和内嵌式接头.第013部分:温度小于260℃铜导体压接用绝缘和防潮的内嵌式接头.产品标准
Terminal lugs and in-line splices for crimping
on electric conductors - Part 013: In-line splices,
insulated and moisture resistant, for crimping
on copper conductors, temperature up to 260
℃ - Product standard
BS EN 3566-2001 航空航天系列.钛合金8°30'管连接件.带锁紧装置的转接头
Aerospace series - Pipe coupling 8 °30' in titanium
alloy - Adaptor with lockring
BS EN 3690-2001 航空航天系列.钛合金8°30'管联接件.长闷头活接头 Aerospace
series - Pipe coupling 8 °30' in titanium alloy
- Unions, bulkhead, long
BS EN 3691-2001 航空航天系列.钛合金8°30'管连接件.长焊接的闷头活接头
Aerospace series - Pipe coupling 8 °30' in titanium
alloy - Unions, bulkhead, long welded
BS EN 3773-003-1999 最大转换容量为65 In/1000 A，额定电流为1A至25A的温度补偿的单极电路断路器.米制螺纹接头.产品标准
Circuit breakers, single-pole, temperature compensated,
rated currents 1 A to 25 A, switching capacity
65 In/1000 A max - Metric thread terminals -
Product standard
BS EN 3773-004-1999 最大转换容量为65 In/1000 A，额定电流为1A至25A的温度补偿的单极电路断路器.UNC螺纹接头.产品标准
Circuit breakers, single-pole, temperature compensated,
rated currents 1 A to 25 A, switching capacity
65 In/1000 A max - UNC thread terminals - Product
standard
BS EN 3774-003-1999 转换容量为65 In，额定电流为2A至25A的温度补偿的三级电路断路器.米制螺纹接头.产品标准
Circuit breakers, three-pole, temperature compensated,
rated currents 2A to 25A, switching capacity
65 In - Metric thread terminals - Product standard
BS EN 3774-004-1999 转换容量为65 In，额定电流为2A至25A的温度补偿的三级电路断路器.UNC螺纹接头.产品标准
Circuit breakers, three-pole, temperature compensated,
rated currents 2A to 25A, switching capacity
65 In - UNC thread terminals - Product standard
BS EN 3852-2002 航空航天系列.TI-P64001型钛合金制、球形、60度管连接器.直螺纹式焊接接头
Aerospace series - Pipe couplings, 60 °, spherical,
in titanium alloy TI-P64001 - Straight unions,
welded, threaded
BS EN 3853-2002 航空航天系列.TI-P64001型钛合金制、球形、60度管连接器.直活螺纹接头
Aerospace series - Pipe couplings, 60 °, spherical,
in titanium alloy TI-P64001 - Straight unions,
threaded
BS EN 387-2002 胶合层压板.大指形接头.性能要求和最低生产要求 Glued
laminated timber - Large finger joints - Performance
requirements and minimum production requirements
BS EN 4031-2001 航空航天系列.钛合金管连接件8°30'.焊接活接头用螺母
Aerospace series - Pipe coupling 8 °30' in titanium
alloy - Nut for welded union
BS EN 4051-2002 航空航天系列.TI-P64001型钛合金制、球形、60度管连接器.油口接头
Aerospace series - Pipe couplings, 60 °, spherical,
in titanium alloy - Port connection
BS EN 4186-2001 航空航天系列.钛合金管连接件8°30'.十字形活接头 Aerospace
series - Pipe coupling 8 °30' in titanium alloy
- Unions, cross
BS EN 4233-2001 航空航天系列.钛合金管连接件8°30'.带螺纹的焊接活接头
Aerospace series - Pipe coupling 8 °30' in titanium
alloy - Unions, welded, threaded
BS EN 4552-2003 航空航天系列.耐热钢制球面37 管联接器.端部焊接的直管接头.英制
Aerospace series - Pipe coupling 37 °, spherical,
in heat resisting steel - Straight nipples,
welded end - Inch series
BS EN 4553-2003 航空航天系列.耐热钢制球面37 管联接器.端部焊接的90
弯头管接头.英制 Aerospace series - Pipe coupling 37
°, spherical, in heat resisting steel - Elbow
90 ° nipples, welded end - Inch series
BS EN 4557-2003 航空航天系列.耐热钢制球面37 管联接器.端部焊接的T形管接头.英制
Aerospace series - Pipe coupling 37 °, spherical,
in heat resisting steel - Tees nipples, welded
end - Inch series
BS EN 4610-2005 航空航天系列.8°30'钛合金管接头.带推进线螺母的45°弯头
Pipe coupling 8°30' in titanium alloy — Elbows
45°, with thrust wire nut
BS EN 50377-2-1-2001 光纤通信系统使用的接头组件和互连元件.产品规范.接线端设在IEC
60793-2类B1单模纤维上的FC-PC型 Connectors sets and interconnect
components to be used in optical fibre communication
systems - Product specifications - Type FC-PC
terminated on IEC 60793-2 category B1 singlemode
fibre
BS EN 512-1995 纤维水泥制品.压力管道和接头 Fibre-cement products
- Pressure pipes and joints
BS EN 514-2000 制作门窗用未增塑聚氯乙烯(PVC-U)型材.胶结角和T接头的强度测定
Unplasticized polyvinylchloride (PVC-U) profiles
for the fabrication of windows and doors - Determination
of the strength of welded corners and T-joints
BS EN 61284-1998 架空线.接头要求和试验 Overhead lines
- Requirements and tests for fittings
BS EN 61300-2-33-2007 纤维光学互联装置和无源部件.基本试验和测量程序.试验.光缆接头盒组装和拆卸
Fibre optic interconnecting devices and passive
components - Basic test and measurement procedures
- Tests - Assembly and disassembly of fibre
optic closures
BS EN 61466-1-1997 标称电压超过1000V的架空线用复合绝缘子串组合件.标准强度等级和接头配件
Composite string insulator units for overhead
lines with a nominal voltage greater than 1
000 V. Standard strength classes and end fittings
BS EN 639-1995 包括接头和配件的混凝土压力管的共同要求 Common requirements
for concrete pressure pipes including joints
and fittings
BS EN 640-1995 钢筋混凝土压力管和分布钢筋混凝土压力管（非圆柱型），包括接头和配件
Reinforced concrete pressure pipes and distributed
reinforcement concrete pressure pipes (non-cylinder
type), including joints and fittings
BS EN 641-1995 包括接头和配件的圆柱型加筋混凝土压力管 Reinforced
concrete pressure pipes, cylinder type, including
joints and fittings
BS EN 642-1995 包括接头、配件和管道预应力钢特殊要求的圆柱型和非圆柱型预应力混凝土压力管
Prestressed concrete pressure pipes, cylinder
and non-cylinder, including joints, fittings
and specific requirement for prestressing steel
for pipes
BS EN 715-1995 热塑管道系统.小直径压力管和配件间端部负荷轴承接头.在包含端推力的内部水压下密封性的试验方法
Thermoplastics piping systems - End-load-bearing
joints between small diameter pressure pipes
and fittings - Test method for leaktightness
under internal water pressure, including end
thrust
BS EN 751-1-1997 与第1,2,3类家庭用燃气和热水装置连接的金属螺纹接头的密封材料.厌氧密封剂
Sealing materials for metallic threaded joints
in contact with 1st, 2nd and 3rd family gases
and hot water - Anaerobic jointing compounds
BS EN 751-2-1997 与第1,2,3类家庭用燃气和热水装置连接的金属螺纹接头的密封材料.非硬化密封剂
Sealing materials for metallic threaded joints
in contact with 1st, 2nd and 3rd family gases
and hot water - Non-hardening jointing compounds
BS EN 751-3-1997 第1,2,3类家庭用燃气和热水装置连接的金属螺纹接头的密封材料.非烧结PTFE密封带.
Sealing materials for metallic threaded joints
in contact with 1st, 2nd and 3rd family gases
and hot water - Unsintered PTFE tapes
BS EN 804-1995 塑料管道系统.压力管道溶剂胶粘接头的注射模塑承口连接管件.短期内部液压压力的试验方法
Plastics piping systems - Injection-moulded
socket fittings for solvent-cemented joints
for pressure piping - Test method for resistance
to a short-term internal hydrostatic pressure
BS EN 846-3-2000 圬工辅助砌块的试验方法.预制基地加固处接头的剪切负载容量的测定
Methods of test for ancillary components for
masonry - Determination of shear load capacity
of welds in prefabricated bed joint reinforcement
BS EN 877-1999+A1-2006 建筑物中水排放用生铁管和配件及其接头和配件.要求、试验方法和质量保证
Cast iron pipes and fittings, their joints and
accessories for the evacuation of water from
buildings — Requirements, test methods and quality
assurance
BS EN 911-1996 塑料管道系统.热塑塑料压力管道用的弹性密封环型接头和机械接头.外部流体静压条件下防漏密封试验方法
Plastics piping systems - Elastomeric sealing
ring type joints and mechanical joints for thermoplastics
pressure piping - Test method for leaktightness
under external hydrostatic pressure
BS EN ISO 10042-2006 焊接.铝和铝合金弧焊接头.缺陷质量分级 Welding
- Arc-welded joints in aluminium and its alloys
- Quality levels for imperfections
BS EN ISO 10692-2-2001 气瓶.用于微电子工业的储气瓶阀的连接接头.接到钢瓶连接接头上的阀门的定型试验和规范
Gas cylinders - Gas cylinder valve connections
for use in the microelectronics industry - Specification
and type testing for valve to cylinder connections
BS EN ISO 11144-1997 牙科设备.漱口冲洗牙用给排水管接头 Dental
equipment - Connections for supply and waste
lines
BS EN ISO 13844-2000 塑料管道系统.与未增塑聚氯乙烯管一起使用的未增塑聚氯乙烯弹性密封环式套筒接头.负压下的密封性试验方法
Plastics piping systems - Elastomeric-sealing-ring-type
socket joints of unplasticized poly(vinyl chloride)
(PVC-U) for use with PVC-U pipes - Test method
for leaktightness under negative pressure
BS EN ISO 13845-2000 塑料管道系统.与未增塑聚氯乙烯管一起使用的弹性密封环式套筒接头.内压下角度偏转密封试验
Plastics piping systems - Elastomeric-sealing-ring-type
socket joints for use with unplasticized poly(vinyl
chloride) (PVC-U) pipes - Test method for leaktightness
under internal pressure and with angular deflection
BS EN ISO 13846-2001 塑料管道系统.热塑性压力管用端负载和无端负载支承组件和接头.内部水压下长期密封性的试验方法
Plastics piping systems - End-load-bearing and
non-end-load bearing assemblies and joints for
thermoplastics pressure piping - Test method
for long-term leaktightness under internal water
pressure
BS EN ISO 13919-1-1997 焊接.电子和激光束焊接接头.缺陷的质量级别导则.钢
Welding - Electron and laser beam welded joints
- Guidance on quality levels for imperfections
- Steel
BS EN ISO 13919-2-2001 焊接.电子和激光束焊接接头.缺陷的质量分级指南.铝及其可焊合金
Welding - Electron and laser beam welded joints
- Guidance on quality levels for imperfections
- Aluminium and its weldable alloys
BS EN ISO 14324-2003 电阻点焊.焊接有损试验.点焊接头的疲劳试验方法
Resistance spot welding - Destructive tests
of welds - Method for the fatigue testing of
spot welded joints
BS EN ISO 15236-4-2004 钢丝绳运输带.硫化的带接头 Steel cord
conveyor belts - Vulcanized belt joints
BS EN ISO 15245-1-2001 气瓶.连接储气瓶阀门接头用平行螺纹.规范
Gas cylinders - Parallel threads for connection
of valves to gas cylinders - Specification
BS EN ISO 16070-2006 石油和天然气工业.下降孔设备.锁紧芯轴和落地螺纹接头
Petroleum and natural gas industries - Downhole
equipment - Lock mandrels and landing nipples
BS EN ISO 17659-2004 焊接.带图解的焊接接头的多语种术语 Welding
- Multilingual terms for welded joints with
illustrations
BS EN ISO 22825-2006 接头的无损检验.超声波试验.奥氏体钢和镍基合金接头的试验
Non-destructive testing of welds - Ultrasonic
testing - Testing of welds in austenitic steels
and nickel-based alloys
BS EN ISO 4797-2005 实验室玻璃器皿.锥形磨口接头烧瓶 Laboratory
glassware - Boiling flasks with conical ground
joints
BS EN ISO 5356-1-2004 麻醉和呼吸设备.圆锥形接头.锥体和锥套 Anaesthetic
and respiratory equipment - Conical connectors
- Cones and sockets
BS EN ISO 5620-1-1997 造船和海上建筑物.饮用水箱注水接头.总要求
Shipbuilding and marine structures - Filling
connection for drinking water tanks - General
requirements
BS EN ISO 5620-2-1997 造船和海上建筑物.饮用水箱注水接头.部件 Shipbuilding
and marine structures - Filling connection for
drinking water tanks - Components
BS EN ISO 5817-2007 焊接.钢、镍、钛和其合金的熔焊接头(束焊除外).缺陷的质量等级
Welding - Fusion-welded joints in steel, nickel,
titanium and their alloys (beam welding excluded)
- Quality levels for imperfections
BS EN ISO 5828-2001 电阻焊设备.连接水冷接头的二次接线电缆.尺寸和特性
Resistance welding equipment - Secondary connecting
cables with terminals connected to water-cooled
lugs - Dimensions and characteristics
BS EN ISO 6149-1-2007 用于液压传动和一般用途的管接头.带ISO 261米制螺纹和O形密封圈的端口和螺纹端头.O形密封用平切壳体端口
Connections for hydraulic fluid power and general
use - Ports and stud ends with ISO 261 metric
threads and O-ring sealing - Ports with truncated
housing for O-ring seal
BS EN ISO 6149-2-2007 液压流体传动和一般用途的管接头.带ISO 261米制螺纹和O形密封圈的油口和螺纹端头.重型(S系列)螺柱端头的尺
Connections for hydraulic fluid power and general
use - Ports and stud ends with ISO 261 metric
threads and O-ring sealing - Dimensions , design,
test methods and requirements for heavy-duty
(S series) stud ends
BS EN ISO 6149-3-2007 液压流体传动和一般用途的管接头.带ISO 261米制螺纹和O形密封圈的油口和螺纹端头.轻型(L系列)螺柱端头的尺
Connections for hydraulic fluid power and general
use - Ports and stud ends with ISO 261 metric
threads and O-ring sealing - Dimensions , design,
test methods and requirements for light-duty
(L series) stud ends
BS EN ISO 8092-1-1998 道路车辆.车上电气布线线束的连接.单极连接接头用接线片.尺寸和特殊要求
Road vehicles - Connections for on-board electrical
wiring harnesses - Tabs for single-pole connections
- Dimensions and specific requirements
BS EN ISO 8434-4-2000 液压及通用金属管连接件.有O形面焊接管接头的24度锥形连接件
Metallic tube connections for fluid power and
general use - 24 ° cone connectors with O-ring
weld-on nipples
BS EN ISO 9692-2-1998 焊接和相关工艺.接头的预处理.钢的埋弧焊 Welding
and allied processes - Joint preparation - Submerged
arc welding of steels
BS EN ISO 9692-3-2001 焊接和相关工艺.接头的准备.铝及其合金的金属极惰性气体保护焊和钨极惰性气体保护焊
Welding and allied processes - Joint preparation
- Metal inert gas welding and tungsten inert
gas welding of aluminium and its alloys
BS EN ISO 9692-4-2003 焊接和相关工艺.接头制备.包钢 Welding
and allied processes - Joint preparation - Clad
steels
BS ISO 10955-1999 飞行器操纵钢丝绳用末端接头和松紧套筒.技术规范 End-fittings
and turnbarrels for aircraft control wire rope
- Technical specification
BS ISO 12151-2-2003 液压传动和通用联接件.软管接头.带ISO 8434-1和ISO
8434-4 O形圈24锥形末端的软管接头 Connections for hydraulic
fluid power and general use - Hose fittings
- Hose fittings with ISO 8434-1 and ISO 8434-4
24 ° cone connector ends with O-rings
BS ISO 12151-4-2007 用于液压流体传动和一般用途的接头.软管配件.带ISO
6149米制螺柱端头的软管配件 Connections for hydraulic fluid
power and general use - Hose fittings - Hose
fittings with ISO 6149 metric stud ends
BS ISO 12151-5-2007 用于液压流体传动和一般用途的接头.软管组件.带ISO
8434-2 37°扩口端的软管配件 Connections for hydraulic
fluid power and general use - Hose fittings
- Hose fittings with ISO 8434-2 37 ° flared
ends
BS ISO 13486-1-1999 道路车辆.液压制动系统.双扩口管,螺纹孔,外螺纹接头和管座
Road vehicles - Hydraulic braking systems -
Double-flare pipes, tapped holes, male fittings
and tube seats
BS ISO 13950-2007 塑料管和管件.电熔合接头用自动识别系统 Plastics
pipes and fittings - Automatic recognition systems
for electrofusion joints
BS ISO 13953-2001 聚乙烯管道和配件.根据对焊接头对试样的抗拉强度和断裂模式的测定
Polyethelene (PE) pipes and fittings - Determination
of the tensile strength and failure mode of
test pieces from a butt-fused joint
BS ISO 15509-2001 粘合剂.工程塑料接头粘合强度测定 Adhesives
- Determination of the bond strength of engineering-plastic
joints
BS ISO 16422-2006 压力送水用定向未增塑聚(氯)乙烯(PVC-O)制作的管道和接头.规范
Pipes and joints made of oriented unplasticized
poly(vinyl chloride) (PVC-O) for the conveyance
of water under pressure - Specifications
BS ISO 22826-2006 金属材料焊缝的破坏性试验.激光和电子束焊测定窄接头硬度的试验(维氏和努氏硬度试验)
Destructive tests on welds in metallic materials
- Hardness testing of narrow joints welded by
laser and electron beam (Vickers and Knoop hardness
tests)
BS ISO 24497-3-2007 无损检验.金属磁存储器.焊接接头的检验 Non-destructive
testing - Metal magnetic memory - Inspection
of welded joints
BS ISO 2974-2005 柴油机.60°锥孔的高压油管接头管端部连接 Diesel
engines - High-pressure fuel injection pipe
end-connections with 60 ° female cone
BS ISO 5675-2008 农业拖拉机和机械.通用快动液压接头 Agricultural
tractors and machinery - General purpose quick-action
hydraulic couplers
BS ISO 6149-4-2006 用于流体传动和一般用途的管接头.带ISO 261米制螺纹和O形圈密封的油口和螺纹端头.内外六角端口栓塞的尺寸、
Connections for fluid power and general use
- Ports and stud ends with ISO 261 metric threads
and O-ring sealing - Dimensions, design, test
methods and requirements for external and internal
hex port plugs
BS ISO 6162-1-2002 液压传动.带对开夹或整体式法兰夹的法兰接头以及公制或英制螺钉.在压力为3,5MPa(35bar)至35MPa(350bar),DN1
Hydraulic fluid power - Flange connectors with
split or one-piece flange clamps and metric
or inch screws - Flange connectors for use at
pressures of 3,5 MPa (35 bar) to 35 MPa (350
bar), DN 13 to DN 127
BS ISO 6162-2-2002 液压传动.带对开夹或整体式法兰夹的法兰接头以及公制或英制螺钉.在压力为35MPa(350bar)至40MPa(400bar),DN1
Hydraulic fluid power - Flange connectors with
split or one-piece flange clamps and metric
or inch screws - Flange connectors for use at
pressures of 35 MPa (350 bar) to 40 MPa (400
bar), DN 13 to DN 51
BS ISO 6489-2-2002 农用车辆.被牵引和牵引车辆间的机械连接装置.第2部分:40号
U型钩接头的规范 Agricultural vehicles - Mechanical
connections between towed and towing vehicles
- Specifications for clevis coupling 40
BS ISO 7169-2007 航空航天.液压系统用24°锥形的、压力范围截至3000psi或21000kPa的可拆卸管接头.采购规范(英制/米制)
Aerospace - Separable tube fittings for fluid
systems, for 24 ° cones, for pressures up to
3000 psi or 21000 kPa - Procurement specification,
inch/metric
BS ISO 7241-2-2000 液压传动.快换接头.试验方法 Hydraulic
fluid power - Quick-action couplings - Test
methods
BS ISO 7876-4-2005 燃油喷射装置.词汇.高压管和末端接头 Fuel injection
equipment - Vocabulary - High-pressure pipes
and end-connections
BS ISO 8267-1-2006 飞行器.牵引杆附属接头的接口要求.干线飞行器 Aircraft
- Tow bar attachment fittings interface requirements
- Main line aircraft
BS ISO 8267-2-2006 飞行器.牵引杆附属接头的接口要求.区域性飞行器 Aircraft
- Tow bar attachment fittings interface requirements
- Regional aircraft
BS ISO 8434-2-2007 液压传动和通用金属管连接件.37°扩口管接头 Metallic
tube connections for fluid power and general
use - 37 ° flared connectors
BS ISO 8434-3-2005 用于液压传动和一般用途的金属管接头.O形圈端面密封管接头
Metallic tube connections for fluid power and
general use - O-ring face seal connectors
BS SP 119 and SP 120-1957 航空用高强度钢叉形接头(统一螺纹)
High tensile steel fork joints (Unified threads)
for aircraft
BS SP 33-39-1951 航空用旋转套筒、张力杆和型锻钢丝绳端面接头规范 Specifications
for turnbarrels, tension rods and swaged cable-end
connections for aircraft
德国接头标准(DIN joint standards)
--------------------------------------------------------------------------------
编号 中文名称 英文名称
DIN 11851-1998 食品,化学和医药工业用管接头.不锈钢制螺纹管连接件.滚压和焊接连接的设计
Fittings for food, chemical and pharmaceutical
industry - Stainless steel screwed pipe connections
- Design for rolling in and welding-on
DIN 11852-2009 食品业、化工业用装置 不锈钢装置 焊接用三通管、弯头和异径接头
Fittings for the food and chemical industries
- Fittings of stainless steel - Tees, bends
and reducers for welding
DIN 11854-1991 食品工业用管配件.不锈钢制软管.带螺纹的软管接头和软管锥形接头
Food industry fittings; hose unions of stainless
steel; threaded hose couplings, conical hose
couplings
DIN 11865-2003 无菌、化学工业和药业用不锈钢配件.焊接用三通管、弯头和异径接头
Stainless steels fittings for aseptic, chemical
and pharmaceutical industries - Tees, bends,
reducers for welding on
DIN 11887-1998 食品,化学和医药工业用管接头.圆螺纹连接件.螺纹连接件和锥形连接件的设计
Fittings for food, chemical and pharmaceutical
industry - Round thread connections - Design
of threaded and conical connection pieces
DIN 12257-1981 实验室玻璃仪器.转换接头 Laboratory glassware;
adapters
DIN 12263-1963 球形磨制接头用夹子 Clamps for spherical-ground
joints
DIN 12784-1984 实验室玻璃仪器.带可互换磨口接头的温度计 Laboratory
glassware; thermometers with interchangeable
ground joint
DIN 13090-4-1986 医疗器械用锥形接头.（经尿道前列腺）切除器用锁紧接头
Conical fittings for medical equipment; lock
fittings for resectoscopes
DIN 1380-2001 小便池接头.要求和试验 Connectors for urinals
- Requirements and testing
DIN 14244-2003 地上和地下消防用抽水接头 Water suction connection
for fire fighting - Under and above ground
DIN 14307-2-1986 抽吸用C型、标称压力16带密封圈的铝合金刚性接头 Aluminium
alloy solid coupling type C with sealing ring
for suction purposes; nominal pressure 16
DIN 14308-2-1986 抽吸用B型、标称压力16带密封圈的铝合金刚性接头 Aluminium
alloy solid coupling type B with sealing ring
for suction purposes; nominal pressure 16
DIN 14311-1985 标称压力为16抽吸和压力用铝合金消防水龙带C型管接头 Aluminium
alloy cap fire hose coupling type C, for pressure
and suction purposes; nominal pressure 16
DIN 14341-1986 标称压力为16的 铝合金C-D型转接接头 Aluminium
alloy C-D-adaptor for nominal pressure 16
DIN 14342-1986 标称压力为16的 铝合金B-C型转接接头 Aluminium
alloy B-C-adaptor for nominal pressure 16
DIN 14343-1986 标称压力为16 的铝合金A-B型转接接头 Aluminium
alloy A-B-adaptor for nominal pressure 16
DIN 14640-1974 消防设备.喷射器、带孔轴、接头的安装 Fire fighting
equipment; fixing for projectors, boring pivot,
joint
DIN 15325-1990 提升设备和服务提升设备.控制装置，信号装置和附加接头 Lifts
and service lifts; control devices, signals
and additional fittings; ISO 4190-5, edition
1987 modified
DIN 1565-1997 有轨车辆用钢管配件.短管接头.双端短管接头.过渡接头 Steel
fittings for railway vehicles - Pipe nipples,
double pipe nipples, swadged nipples
DIN 1566-1997 有轨车辆用钢管配件.双过渡接头.缩径双端短管接头 Steel
fittings for railway vehicles - Double nipples,
reduced double nipples
DIN 1569-1997 有轨车辆用钢管配件.直角弯头.叉形接头 Steel fittings
for railway vehicles - Elbows, Y-fittings
DIN 16450-1994 未增朔聚氯乙烯压力管道的套管接头.符号 Socket-fittings
for pressure piping of unplasticized polyvinylchloride
(PVC-U); symbols
DIN 16867-1982 化工管路用玻璃纤维增强式聚酯树脂管道、配件和接头.交货技术条件
Glass fibre reinforced polyester resin (UP-GF)
pipes, fittings and joints for use in chemical
pipelines; Technical delivery conditions
DIN 16872-1993 热塑性塑料管道用管接头组件.玻璃纤维增强的聚酯树脂(UP-GE)法兰.尺寸
Pipe joints assemblies for pipelines of thermoplastics;
glass fibre reinforced polyester resin (UP-GF)
flanges; dimensions
DIN 16928-1979 热塑性塑料管道.管接头、管道部件、管道敷设.一般说明 Pipes
of Thermoplastic Materials; Pipe Joints, Elements
for Pipes, Laying; General Directions
DIN 16962-1-1980 1型和2型聚丙烯压力管道用管接头和零组件.对焊用弓形结构弯头.尺寸
Pipe Joints and Elements for Polypropylene (PP)
Pressure Pipelines, Types 1 and 2; Bends of
Segmental Construction for Butt-welding, Dimensions
DIN 16962-11-1980 1型和2型聚丙烯压力管道用管接头和零组件.用于对焊的车削和压制减径管套.尺寸
Pipe Joints and Elements for Polypropylene (PP)
Pressure Pipelines, Types 1 and 2; Turned and
Pressed Reducing Sockets for Butt-welding, Dimensions
DIN 16962-12-1999 聚丙烯(PP)制压力管道用管连接件和零件.PP-H
100,PP-B 80和PP-R 80.第12部分:承口焊接用凸缘接头、法兰、密 Pipe
joints and components of polypropylene (PP)
for pipes under pressure, PP-H 100, PP-B 80
and PP-R 80 - Part 12: Flange adapters, flanges,
sealing rings for socket welding; dimensions
DIN 16962-13-1987 1型和2型聚丙烯压力管道用管连接件和接头.管接头.尺寸
Pipe joint assemblies and fittings for type
1 and type 2 polypropylene (PP) pressure pipes;
pipe couplings; dimensions
DIN 16962-2-1983 1型和2型聚丙烯压力管道用管接头组件和接头.用对焊的分段嵌入和减颈方法制造的T型管及支管.尺寸
Pipe joint assemblies and fittings for types
1 and 2 polypropylene (PP) pressure pipes; tees
and branches produced by segment inserts and
necking for butt welding; dimensions
DIN 16962-3-1980 1型和2型聚丙烯压力管道用管接头和零组件.对焊用管成形弯头.尺寸
Pipe Joints and Elements for Polypropylene (PP)
Pressure Pipelines, Types 1 and 2; Bends Formed
from Pipe for Butt-welding, Dimensions
DIN 16962-4-1988 1型和2型聚丙烯压力管道用管道连接组件和管道配件.第4部分:熔焊、法兰和密封元件管接头尺寸
Pipe joint assemblies and fittings for types
1 and 2 polypropylene (PP) pressure pipes; adaptors
for fusion jointing, flanges and sealing elements;
dimensions
DIN 16962-6-1980 1型和2型聚丙烯压力管道用管接头和零组件.承插焊接用注塑弯头.尺寸
Pipe Joints and Elements for Polypropylene (PP)
Pressure Pipelines, Types 1 and 2; Injection
Moulded Elbows for Socket-welding, Dimensions
DIN 16962-7-1980 1型和2型聚丙烯压力管道用管接头和零组件.承插焊接用注塑三通.尺寸
Pipe Joints and Elements for Polypropylene (PP)
Pressure Pipelines, Types 1 and 2; Injection
Moulded Tee Pieces for Socket-welding, Dimensions
DIN 16962-8-1980 1型和2型聚丙烯压力管道用管接头和零组件.承插焊接用注塑管套和管帽.尺寸
Pipe Joints and Elements for Polypropylene (PP)
Pressure Pipelines, Types 1 and 2; Injection
Moulded Sockets and Caps for Socket-welding,
Dimensions
DIN 16962-9-1983 1型和2型聚丙烯压力管道用管连接组件和接头.承插焊接用注塑减径管件与套管.尺寸
Pipe joint assemblies and fittings for types
1 and 2 polypropylene (PP) pressure pipes; injection
moulded reducers and nipples for socket welding;
dimensions
DIN 16963-10-1980 1型和2型高密度聚乙烯压力管道用管子接头与零件.承插焊接用注塑套筒与帽盖.尺寸
Pipe Joints and Elements for High Density Polyethylene
(HDPE) Pressure Pipelines, Types 1 and 2; Injection
Moulded Sockets and Caps for Socket-welding,
Dimensions
DIN 16963-11-1999 聚乙烯(PE)制压力管道用管连接件和零件.PE 80和PE
100.第11部分:承口焊接用凸缘接头、法兰、密封圈.尺寸 Pipe joints and
components of polyethylene (PE) for pipes under
pressure, PE 80 and PE 100 - Part 11: Flange
adapters, flanges, sealing rings for socket
welding; dimensions
DIN 16963-13-1980 1型和2型高密度聚乙烯压力管道用管子接头与零件.对焊用车削的和压制的缩径承接件.尺寸
Pipe Joints and Elements for High Pressure Polyethylene
(HDPE) Pressure Pipelines, Types 1 and 2; Turned
and Pressed Reducing Sockets for Butt-welding,
Dimensions
DIN 16963-14-1983 1型和2型高密度聚乙烯压力管道用管连接组件和接头.承插焊接用注塑减径管件与套管.尺寸
Pipe joint assemblies and fittings for types
1 and 2 high-density polyethylene (HDPE) pressure
pipes; injection moulded reducers and nipples
for socket welding; dimensions
DIN 16963-15-1987 高密度聚乙烯压力管道用管连接件和接头.管接头.尺寸
Pipe joint assemblies and fittings for high-density
polyethylene (HDPE) pressure pipes; pipe couplings;
dimensions
DIN 16963-2-1983 1型和2型高密度聚乙烯压力管道用管接头组件和配件.用对焊的分段嵌入和缩颈方法制造的T型管及支管.尺寸
Pipe joint assemblies and fittings for types
1 and 2 high-density polyethylene (HDPE) pressure
pipes; tees and branches produced by segment
inserts and necking for butt welding; dimensions
DIN 16963-3-1980 1型和2型高密度聚乙烯压力管道用管子接头与零件.对焊用弯管.尺寸
Pipe Joints and Elements for High Density Polyethylene
(HDPE) Pressure Pipelines, Types 1 and 2; Pipe
Bends for Butt-welding, Dimensions
DIN 16963-4-1988 高密度聚乙烯压力管道用管道连接组件和管道配件.第4部分:熔焊、法兰和密封元件管接头尺寸
Pipe joint assemblies and fittings for high-density
polyethylene (PE-HD) pressure pipes; adaptors
for fusion jointing, flanges and sealing elements;
dimensions
DIN 16963-8-1980 1型和2型高密度聚乙烯压力管道用管子接头与零件.承插焊接用注塑弯管.尺寸
Pipe Joints and Elements for High Density Polyethylene
(HDPE) Pressure Pipelines, Types 1 and 2; Injection
Moulded Elbows for Socket-welding, Dimensions
DIN 16963-9-1980 1型和2型高密度聚乙烯压力管道用管子接头与零件.承插焊接用注塑三通管件.尺寸
Pipe Joints and Elements for High Density Polyethylene
(HDPE) Pressure Pipelines, Types 1 and 2; Injection
Moulded Tee Pieces for Socket-welding, Dimensions
DIN 16966-2-1982 玻璃纤维增强式聚酯树脂管道配件和接头.弯管.尺寸 Glass
fibre reinforced polyester resin (UP-GF) pipe
fittings and joints; Elbows, Dimensions
DIN 16966-4-1982 玻璃纤维增强聚酯树脂管(UP-GF)管件和接头.三通喷管嘴尺寸
Glass fibre reinforced polyester resin (UP-GF)
pipe fittings an joints; Tees, Nozzles, Dimensions
DIN 16966-5-1982 玻璃纤维增强聚酯树脂管(UP-GF)管件和接头.缩径管.尺寸
Glass fibre reinforced polyester resin (UP-GF)
pipe fittings and joints; Reducers, Dimensions
DIN 16966-6-1982 玻璃纤维增强聚酯树管(UP-GF)管件和接头组件.卡圈、法兰、密封圈、尺寸
Glass fibre reinforced polyester resin (UP-GF)
pipe fittings and joint assemblies; collars,
flanges, joint rings, dimensions
DIN 16966-8-1982 玻璃纤维增强聚酯管(UP-GF)管件和接头.层压塑料接头.尺寸
Glass fibre reinforced polyester resin (UP-GF)
pipe fittings and joints; Laminated joints;
Dimensions
DIN 16967-2-1982 玻璃纤维增强环氧树脂(EP-GF)管件和接头.弯管、三通管、尺寸
Glass fibre reinforced epoxy resin (EP-GF) pipe
fittings and joints; Elbows, Tees, Dimensions
DIN 18195-8-2004 建筑物的防水性.第8部分:活动连接接头的防水性 Water-proofing
of buildings - Part 8: Water-proofing over joints
for movements
DIN 18318-2006 建筑合同程序(VOB).第C部分:建筑合同通用技术规范(ATV).道路建设.接头易断裂的方块铺石和混凝土路面及环境
Construction contract procedures (VOB) - Part
C: General technical specifications in construction
contracts (ATV) - Road construction - Dry-jointed
sett and slab pavements, and surrounds
DIN 19004-1980 快门线点动开关螺纹.接头和插口.连接尺寸 Screw threads
of shutter cable release; tip and socket, connecting
dimensions
DIN 19560-10-1999 建筑物中耐热的废水和污物排放系统用聚丙烯(PP)管材和管接头.第10部分:燃烧特性.质量控制和推荐标准
Pipes and fittings made of polypropylene (PP)
for hot water resistant waste and soil discharge
systems inside buildings - Part-10: Fire behaviour,
quality control and installation recommendations
DIN 19850-2-1996 纤维水泥污水管和接头.第2部分:接头尺寸 Fibre
cement pipes and fittings for sewers - Part
2: Dimensions of joints
DIN 20029-1990 软管管接头.1:3 锥度量规 Hose fittings;
1:3 taper gauges
DIN 20035-1990 软管管接头.法兰管嘴.公称压力16 Hose fittings;
flange nozzle; nominal pressure 16
DIN 20036-1990 软管管接头.圆螺纹的管接头套管 Hose fittings;
coupling nipples with round thread form
DIN 20037-1990 软管管接头.连接套管.尺寸 Hose fittings;
connecting nipple; dimensions
DIN 20038-1990 软管管接头.接头管嘴 Hose fittings; coupling
nozzles
DIN 20040-1990 软管管接头.连接套管阀.公称压力16 Hose fittings;
nipple valves; nominal pressure 16
DIN 21388-1988 绳索装置.通用接头 Rope attachments; universal
joints
DIN 22110-3-2007 输送带接头的测试方法.第3部分:输送带接头耐久性的测定(动态测试法)
Testing methods for conveyor belt joints - Part
3: Determination of time strength for conveyor
belt joints (dynamical testing method)
DIN 22121-2000 煤矿用织物叠层输送带.单层或双层带的永久性连接接头.尺寸、要求和标记
Conveyor belts with textile plies for coalmining
- Permanent joints for belts with one or two
plies; dimensions, requirements, marking
DIN 22418-1989 矿山预防潜在的爆炸环境用的电气设备；螺旋接头.安全性要求和试验
Electrical apparatus for potentially explosive
atmospheres for mining; screw plugs; safety
requirements and testing
DIN 22419-2-2004 用于潜在爆炸性环境的采掘电气装置.电缆引入线.第2部分:引入线用密封接头.安全要求和检验
Electrical apparatus for potentially explosive
atmospheres for mining - Cable entries - Part
2: Gland adaptors for entries; safety requirements
and testing
DIN 22434-3-2003 无烟煤地下开采照明.照明.技术规划基础.第3部分:T
形接头 Underground lighting in hardcoal mining
- Lighting-technological planning bases - Part
3: T-junctions
DIN 2353-1998 带环套的非焊接压力连接接头.完全压连接和概述 Non-soldering
compression fittings with cutting ring - Complete
fittings and survey
DIN 28030-1-2003 容器和加工装置用法兰接头.第1部分:带法兰的设备用容器
Flanged joints for vessels and process apparatus
- Part 1: Apparatus flanged vessels
DIN 28139-1-1985 搪瓷容器的焊接颈.夹紧螺纹接头的H形主法兰.尺寸 Welding
necks for glass lined vessels; form H main flanges
for clamp screw connections; dimensions
DIN 28145-5-1995 搪玻璃钢搅拌容器用焊接件.第5部分:底部泄料孔处绝缘接头
Parts welded to glass lined steel agitator vessels
- Part 5: Insulation collar at the bottom discharge
opening
DIN 28601-2000 延性铸铁管道和配件.螺纹套管接头.组件、套管、螺丝环、密封环和滑动环
Ductile iron pipes and fittings - Screwed socket
joints - Assembly, sockets, screw rings, sealing
rings and slip rings
DIN 28602-2000 球墨铸铁管及管件.栓接压盖密封接头.组件、套管、中间环、密封圈、螺栓和螺母
Ductile iron pipes and fittings - Bolted gland
joints - Assembly, sockets, counter ring, sealing
ring, bolts and nuts
DIN 2880-1999 铸铁管、钢管和管接头的水泥砂浆管衬料的应用 Application
of cement mortar lining for cast iron pipes,
steel pipes and fittings
DIN 30658-1-1998 地下煤气管道接头附加密封材料.第1部分:已密封煤气管道附加密封用塑料薄膜和织物衬套.安全要求和试验
Materials for the subsequent sealing of joints
in underground gas mains - Part 1: Plastic foil
and textile fibre linings used to seal gaspipes
already in place; safety requirements and testing
DIN 30658-2-1999 地下煤气管道用后续密封材料.第2部分:地下煤气管道接头用后续密封材料.安全要求和试验
Materials for the subsequent sealing of underground
gas mains - Part 2: Materials for the subsequent
sealing of joints in underground gas mains;
safety requirements and testing
DIN 30670-1991 钢管和管接头的聚乙烯涂层.要求和试验 Polyethylen
coatings of steel pipes and fittings; requirements
and testing
DIN 3159-1965 标称压力25以下的制冷设备接头法兰的安装尺寸 Assembling
dimensions of flanges for fittings for refrigerating
installations up to nominal pressure 25
DIN 3281-1988 家用供水管道的阀门.公称压力10的锥形管子接头.概述 Valves
for domestic water supply; tapered union nipples
nominal pressure 10; survey
DIN 3289-1988 家用供水管道的阀门.公称压力为10的螺纹连接管和联管节.带螺纹的锥形管子接头
Valves for domestic water supply; nipples and
unions nominal pressure 10; threaded tapered
union nipples
DIN 3292-1-1984 家用安装设备配件.有色金属活接头螺母 Fittings
for domestic installation; nonferrous metal
union nuts
DIN 3292-2-1984 家用安装设备配件.可锻铸铁活接头螺母 Fittings
for domestic installation; malleable cast iron
union nuts
DIN 3334-1968 带法兰接头的加热装置用混合阀.标称压力为6、最高温度110
℃的三通混合阀、四通混合阀.安装尺寸 Mixing valves for heating
installations with flanges, three way mixing
valves, four way mixing valves, ND 6 max. 110
°C; installation dimensions
DIN 3383-4-1991 软管组件和连接配件.煤气用安全连接配件和试验室管路用接头
Hose assemblies and connection fittings; safety
connection fittings for gas and couplings for
laboratory tubing
DIN 3387-2-1991 煤气管道用带法兰接头的金属管道管连接件 Tube connections
for metallic tubes having flanged ends for gas
pipes
DIN 3389-1984 进宅供气和供水管路安装用商品绝缘接头.要求和检验 Isolating
joints ready for installation into service pipes
in gas and water supply; built-in-isolating
joints; requirements and tests
DIN 3475-1993 未处理水和可饮用水用的球墨铸铁管阀和管接头.内部涂搪瓷防腐蚀.质量要求和试验
Valves and fittings of spheroidal cast iron
for untreated and potable water; corrosion protection
by internal enamelling; quality requirements,
testing
DIN 3476-1996 生水和饮用水用阀门和接头.粉漆及环氧内涂防腐层.要求和检验
Valves and fittings for untreated and potable
water - Protection against corrosion by internal
epoxy coating of coating powders (P) or liquid
varnishes (F) - Requirements and tests
DIN 3533-1981 煤气装置用阀门.带压力接头的角度型旋阀 Valves for
gas installations; angle pattern stop cocks
with compression fitting
DIN 3534-1982 气体装置阀.带压紧接头的直通型龙头 Valves for gas
installations; straight pattern taps with compression
fitting
DIN 3538-1986 煤气装置阀门.蝶型阀.内螺纹接头 Valves for gas
installations; butterfly valves; female threaded
ends
DIN 3799-1975 铁路及道路车辆集装箱连接件.接到标称直径80至100的螺纹接套上的5.5英寸减径接头
Couplings for railway- and truck containers;
reducers adapting 5<(hoch)1>/<(Index)2>
inch to nipples nominal size 80 and 100
DIN 3850-1998 压力连接管接头.概述 Compression fittings
- Summary
DIN 3852-11-1994 压合接头、阀门、螺旋塞和E型螺纹管堵用螺纹管堵和螺纹孔.设计尺寸
Screwed stud-ends; tapped holes; for compression
fittings, valves, screw plugs, screwed stud-ends
type E; design dimensions
DIN 3853-2001 非钎焊和钎焊压合接头.与管接螺母使用的双头螺栓端部.设计图
Non-soldering and soldering compression fittings
- Stud ends for use with union nut; Design sheet
DIN 3854-1995 非钎焊和钎焊压紧联轴节.套管接头用螺纹孔.建造单 Non-soldering
and soldering compression couplings - Tapped
holes for socket unions - Construction sheet
DIN 3861-2002 非焊螺旋活接头.卡套.设计 Non-soldering compression
fittings - Compression rings - Design
DIN 3865-2002 压合接头.符合 DIN EN ISO 8434-1 的压接用带
'O' 型密封圈的24度螺纹接头 Compression fittings - Nipple
24° with O-ring - For compression joint according
to DIN EN ISO 8434-1
DIN 3866-1990 制冷.螺纹堵塞.额定用于40公称压力的非钎焊压紧管接头的90°扩口法兰
Refrigeration; threaded stem; 90° flared flanges
for solderless compression couplings rated for
PN 40
DIN 3870-2001 非钎焊和钎焊压合接头.管接螺母系列LL Non-soldering
and soldering compression fittings - Union nuts
series LL
DIN 3871-1995 非钎焊和钎焊压紧联轴节.套管接头 Non-soldering
and soldering compression couplings - Socket
unions
DIN 3872-2003 非焊接压紧联轴节.对接结构活接头螺母 Non-soldering
compression couplings - Union nuts for butt
joints
DIN 3901-2001 带切割环的非钎焊压合接头.钝端A型带平行螺纹的双钝端接头 Non-soldering
compression fittings with cutting ring - Double
ended stud ends with parallel thread for stub
ends type A
DIN 3904-1987 椭圆形压接管接头.螺柱式插接肘节管 Olive type compression
couplings; male stud elbows
DIN 3907-1987 椭圆形压接管接头..螺柱式插接三通管接头（螺柱分管） Olive
type compression couplings; male stud tees (stud
branch)
DIN 3914-1987 椭圆形压接管接头.螺柱式插接三通管接头（螺柱插接） Olive
type compression couplings; male stud tees (stud
run)
DIN 3942-2002 非焊接的压合接头.符合 DIN EN ISO 8434-1
的压接端头的设计和定型用可调节的带24度锥形联接器和 'O' 型密 Non-soldered
compression fittings - Swivel elbows with 24°
cone connectors with O-ring - Adjustable, for
design and type of compression end according
to DIN EN ISO 8434-1
DIN 3943-2002 非焊接的压合接头.符合 DIN EN ISO 8434-1
的压接端头的设计和定型用可调节的带24度锥形联接器和 'O' 型密 Non-soldered
compression fittings - Swivel branch tees with
24° cone connectors with O-ring - Adjustable,
for design and type of compression end according
to DIN EN ISO 8434-1
DIN 3944-2002 非焊接的压合接头.符合 DIN EN ISO 8434-1
的压接端头的设计和定型用可调节的带24度锥形联接器和 'O' 型密 Non-soldered
compression fittings - L-adaptors with 24° cone
connectors and O-ring - Adjustable, for design
and type of compression end according to DIN
EN ISO 8434-1
DIN 3945-2002 非焊接的压合接头.符合 DIN EN ISO 8434-1
的压接端头的设计和定型用带24度锥形联接器和 'O' 型密封圈的直 Non-soldered
compression fittings - Straight stud swivel
adaptor with 24° cone connectors with O-ring
- For design and type of compression end according
to DIN EN ISO 8434-1
DIN 3946-2002 非焊接的压合接头.符合 DIN EN ISO 8434-1
的压接端头的设计和定型用带24度锥形联接器和 'O' 型密封圈的直 Non-soldered
compression fittings - Straight reducing swivel
adaptors with 24° cone connectors with O-ring
- For design and type of compression end according
to DIN EN ISO 8434-1
DIN 3955-2001 带切割环的非钎焊压合接头.柱螺栓端A型带平行螺纹和轴杆的双头螺栓连接端
Non-soldering compression fittings with cutting
ring - Double ended stud ends with parallel
threads and shaft for stud ends type A
DIN 4000-80-2005 事物特性表.第80部分:螺纹接头、冷成型丝锥和螺纹板牙
Tabular layouts of properties - Part 80: Screwing
tabs, cold forming taps and screwing dies
DIN 4060-1998 带弹性密封件的下水道和污水管用接头.对弹性密封件的接头的要求和试验
Joints of sewer and drain pipes with elastomeric
seals - Requirements and testing on joints with
elastomeric seals
DIN 41652-3-1990 φ1mm的圆形触点、梯形机柜连接器.A型结构尺寸.室外布线用钎焊接头
Rack and panel connectors, trapezoidal, round
contacts 1 mm; dimensions of type A; solder
termination for free wiring
DIN 42017-1984 小型电动机线路接头的配置和标记 Marking and coordination
of the connecting leads for small motors
DIN 42021-1-1976 步进电机.安装尺寸、铭牌、电气接头 Step motors;
mounting dimensions, type plate, electrical
connection
DIN 46199-5-1976 第5部分:定时继电器的接头标记 Terminal markings
of specified-time relays
DIN 46199-6-1974 电器开关设备.第6部分:压力和温度开关设备的接头标记
Electrical switchgear; terminal markings for
pressure and temperature, sensitive devices
DIN 46228-2-1992 带及不带绝缘夹的压接式端部接头 Crimp-type
end-splices, with and without insulation grip
DIN 46228-3-1992 不带绝缘夹的导线端部环绕接头 Conductor-embracing
end-splices, without insulation grip
DIN 46267-1-1985 铜导线用非耐张力的压制接头 Non tension-proof
compression joints for copper conductors
DIN 46267-2-1985 铝导线用非耐张力的压制接头 Non tension-proof
compression joints for aluminium conductors
DIN 46276-1-1991 第1部分:层状柔性母线和扁接线端用膨胀接头 Expansion
joints for busbars and flat terminals; lamellar
flexible
DIN 46276-2-1991 第2部分:层状高柔性母线和扁接线端用膨胀接头 Expansion
joints for busbars and flat terminals; lamellar
high flexible
DIN 46329-1983 铝导线用环形压接的电缆接头耳 Cable lugs; for
compression connections, ring type, for aluminium
conductors
DIN 46330-2-1981 接头规格为２?８的无绝缘套的短插座 Short receptacles;
without insulating sleeve, for tab size 2,8
DIN 46340-1-1981 接头规格为２?８的快速插入插座 Snap-in receptacles
for tab size 2,8
DIN 46340-3-1981 接头规格为6?３的快速插入插座 Snap-in receptacles
for tab size 6,3
DIN 46340-4-1981 接头规格为９?５的快速插入插座 Snap-in receptacles
for tab size 9,5
DIN 46340-5-1981 接头规格为７?7的快速插入插座 Snap-in receptacles
for tab size 7,7
DIN 47619-1-1979 通信电缆接头.对称多股绞合电缆 Splicing of
telecommunication cables; cable with symmetrical
stranding components
DIN 47633-1984 通信电缆的同轴电缆接头.要求和试验 Coaxial splices
in telecommunication cables; requirements, tests
DIN 47635-1973 铸造金属电缆接头用垫片槽和褶皱 Gasket grooves
and folds for cast-metal cable fittings
DIN 477-5-2002 气瓶阀.第5部分:最大试验压力为450巴.出口接头 Gas
cylinder valves - Part 5: For test pressure
up to 450 bar max.; Outlet connections
DIN 48069-2-1980 架空线路用带保护接头的双环 Double eyes with
protective fitting, for overhead power lines
DIN 48085-1-1985 架空线路用铜导线的全拉力压制接头 Full tension
compression joints, for copper conductors, for
overhead lines
DIN 48085-2-1985 架空线路用铝导线的全拉力压制接头 Compression
connectors, restistant to high tensile stresses,
for aluminium-conductors
DIN 48085-3-1985 架空线路用ACSR导线的全拉力压制接头 Full tension
compression joints, for ACSR-conductors, for
overhead lines
DIN 48207-3-2005 额定电压超过1KV的架空线.导体安装的方法和设备.第3部分:带球形接头的电缆连接件
Overhead lines with nominal voltages exceeding
1 kV - Methods and equipment for the installation
of conductors - Part 3: Cable couples with spherical
joint
DIN 49017-2-1981 电气设备用导管和管接头.刚性非火焰扩散绝缘导管和管接头.轻压力强度用带接头的光滑导管和带接头的弯头
Conduits and fittings for electrical installation;
rigid nonflame propagating insulating conduits
and fittings; plain conduits with coupler and
bends with coupler for light pressure strength
DIN 49020-1959 电线导管.带螺纹钢制导管、普通导管和管接头 Conduit
for Electrical Wiring; Screwed Steel Conduit,
Plain Conduit, Couplers
DIN 49023-1975 电气设备用导管和接头.柔性波纹钢管 Conduits and
fittings for electrical installation; flexible
corrugated conduits of steel
DIN 49360-3-1986 D型熔断器.第16部分:管接头螺钉扳手用带功能尺寸的
E 16 测量环 D-type fuses; E 16 gauge rings with
functional dimensions for adapter screw fitters
DIN 49985-1971 电照明接头（发光设备）.玻璃灯泡的橡胶连接件 Electric
lighting fittings (luminaires); rubber joint
for glass-globes
DIN 54455-1984 金属粘合剂和金属粘结接头的检验.扭剪试验 Testing
of adhesives for metals and of bonded metal
joints; torsional shear test
DIN 5466-1-2000 花键接头,载荷能力计算.第1部分:一般基础 Splined
joints, calculation of load capacity - Part
1: General basis
DIN 57220-3-1977 ≤1kV电力电缆设备中带单个和多个绝缘件电缆接头规范
Specifications for single- and multiple cable
clamps with insulating parts in electrical power
cable installations up to 1000 V
DIN 58300-1982 外科器械接头 Joints for surgical instruments
DIN 58736-3-2001 光学加工.定心罩.第3部分:外连接用圆柱形接头.尺寸12mm和25mm
Production in optical engineering - Centering
bells - Part 3: With cylindrical fitting dimension
12 mm and 25 mm for outer connection
DIN 65030-1997 航空航天.带截环的管螺纹接头.交货技术条件.对新设计无效
Aerospace - Solderless tube fittings with coupling
sleeves, flaveless - Technical specification;
inactive for new design
DIN 65053-1992 航空航天.操纵钢缆接头.技术规范.不适用于新设计 Aerospace;
control cable fittings; technical specification;
inactive for new design
DIN 6660-1996 风动管道系统.无增塑剂聚氯乙烯(硬聚氯乙烯)传送管,传送管弯头和接头
Pneumatic tube systems - Conveyor tube, conveyor
tube bend and sleeves for pneumatic tube lines
of unplasticized polyvinylchloride (PVC-U)
DIN 68140-1-1998 木制指形接头.第1部分:承载结构用软木的指形接头 Wood
finger-jointing - Part 1: Finger jointing of
softwood for load-bearing structures
DIN 68601-2002 胶粘的木制品接头.术语和定义 Bonded wood joints
- Terms and definitions
DIN 71428-1989 椭圆形压接连接的管接头.用联管螺母连接的圆柱形螺纹旋入连接管
Compression couplings with olives; cylindrical
thread nipples for use with union nuts
DIN 71429-1989 椭圆形压接连接的管接头.用联螺母连接的闷头压接联接器的小螺柱和肘节管接头
Compression couplings with olives; bulkhead
compression couplings small stud and elbow fittings
for use with union nuts
DIN 71430-1989 椭圆形压接连接的管接头.用联管螺母旋转连的管接头 Compression
couplings with olives; swiveling fittings for
use with union nuts
DIN 71433-1989 椭圆形压接连接的管接头.用联螺母连接的的三通管接头和肘节管接头
Compression couplings with olives; T-fittings
and elbow fittings for use with union nuts
DIN 71436-1989 橄榄形压紧联接器.与管接头配用的空心螺钉管接头和环形管接头
Compression couplings with olives; hollow screw
fittings and ring connection fittings for use
with union nuts
DIN 71752-1994 叉形接头.叉头 Fork joints; yokes
DIN 71802-1992 带开口簧环或不带开口簧环的球形接头 Ball joints
with or without circlips
DIN 71985-1-1982 控制装置用缆索的内接头.储柜的内接头 Nipples
for cables for controls; receiver nipple
DIN 71985-2-1982 控制装置用缆索的管接头.钎焊管接头 Nipples for
cables for controls; nipples for soldering
DIN 71985-3-1982 控制装置用缆索的内接头.夹紧内接头 Nipples for
cables for controls; clamping nipples
DIN 71985-4-1982 绳索传动装置的内接头.第4部分:挤压内接头 Nipples
for cables for controls; nipples for swaging
DIN 71991-1982 控制装置电缆用带螺纹的接头 Threaded end-fittings
for cables for controls
DIN 72535-1979 点火线圈和点火分电器用高压接头 High tension
connection for ignition coils and distributors
DIN 73353-1977 带圆柱接头的油浴式空气滤清器 Oil-wetted airfilters
with cylindrical connection
DIN 74225-1991 液压制动软管组件.制动用软管接头.制动软管夹 Brake
hose assemblies; brake hose fittings; brake
hose clips
DIN 74304-1987 压接管接头.软管接头 Compression coupling;
hose coupling
DIN 74313-1-1994 非焊接压缩管接头.渐缩管.A型和B型 Non-soldering
compression fittings; reducers; type A and B
DIN 74313-2-1994 非焊接压缩管接头.渐缩管.C型和D型 Non-soldering
compression fittings; reducers; type C and D
DIN 7588-1994 家装设备用水管配件.平密封螺旋接头.压力10巴的一端带内螺纹,另一端带钢管喷嘴、铜管喷嘴或套管
Water-fittings for house installation; boltings
with flat seal; one side threaded coupling with
inside-thread, on the other side steel tube
nozzle, copper tube nozzle or sleeve PN 10
DIN 7589-1994 家装设备用水管配件.平密封螺旋接头.压力10巴的一端带外螺纹,另一端带钢管喷嘴、铜管喷嘴和套管
Water-fittings for house installation; boltings
with flat seal; one side threaded coupling with
outside-thread, on the other side steel tube
nozzle, copper tube nozzle or sleeve PN 10
DIN 7601-1998 带球形衬套的压接接头.完整接头和概述 Compression
couplings with ball-type nipples - Complete
unions and survey
DIN 7632-1985 带球面衬套的压紧连轴器.变径接头 Compression couplings
with spherical liner; reducers
DIN 7633-2003 带球衬的压合接头.钎焊用管接头 Compression fittings
with spherical liners - Adapters for brazing
DIN 7637-1985 带球形衬的压接管接头.焊接转接器 Compression fittings
with spherical liners; adaptars for welding
DIN 7638-1985 带球形衬的压接管接头.等长度弯管 Compression couplings
with spherical liner; equal elbows
DIN 7639-1985 带球形衬的压接管接头.等长度三通连接管 Compression
couplings with spherical liner; equal tees
DIN 7640-1985 带球形衬的压接管接头.等长度四通连接管 Compression
couplings with spherical liner; equal crosses
DIN 7642-1997 管螺纹连接.钎焊连接环形管接头 Compression couplings
- Ring type nipples for brazed connection
DIN 7644-1985 带球形衬的压接管接头.环形套管的插桩式鼓形螺栓 Compression
couplings with spherical liner; male studed
banjo bolts for ring type nipples
DIN 7647-1995 带球形衬里的压紧联轴节.平行旋入式接头 Compression
couplings with spherical liners - Adaptors with
parallel screwed-in ends
DIN 8063-1-1986 未增塑聚氯乙烯压力管道用管连接组件和接头.承口弯头尺寸
Pipe joint assemblies and fittings for unplasticized
polyvinyl chloride (U-PVC) pressure pipelines;
dimensions of socket bends
DIN 8063-10-2002 加压管道用未增塑聚氯乙烯的管道连接件和部件.第10部分:管壁支架弯管接头.尺寸
Pipe joints and components of unplasticized
poly(vinyl chloride) (PVC U) for pipes under
pressure - Part 10: Wall bracket elbows; Dimensions
DIN 8063-12-1987 未增塑聚氯乙烯压力管道的管连接组件和接头.带法兰的和承口接头的尺寸
Pipe joint assemblies and fittings of unplasticized
polyvinyl chloride (U-PVC) pressure pipelines;
dimensions of flanged and socket fittings
DIN 8063-3-2002 加压管道用未增塑聚氯乙烯的管道连接件和部件.第3部分:管接头:尺寸
Pipe joints and components of unplasticized
poly(vinyl chloride) (PVC U) for pipes under
pressure - Part 3: Unions; Dimensions
DIN 8063-4-1983 未增塑聚氯乙烯压力管道用管连接组件和接头.内外螺母、法兰盘、密封件.尺寸
Pipe joint assemblies and fittings for unplasticized
polyvinyl chloride (PVC-U) pressure pipes; bushings,
flanges, seals; dimensions
DIN 8063-5-1999 未增塑聚氯乙烯压力管道用管接头和元件(PVC-U).第5部分:一般质量要求、试验
Pipe joints components of unplasticized poly(vinyl
chloride) (PVC-U) for pipes under pressure -
Part 5: General quality requirements, testing
DIN 8063-8-2002 加压管道用未增塑聚氯乙烯的管道连接件和部件.第8部分:溶剂粘结用喷射模塑套管、帽和管接头.尺寸
Pipe joints and components of unplasticized
poly(vinyl chloride) (PVC U) for pipes under
pressure - Part 8: Injection-moulded sockets,
caps and nipples for solvent cementing; Dimensions
DIN 808-1984 机床.万向接头.规格、连接尺寸、负载能力、安装 Machine
tools; cardan joints; sizes, connecting dimensions,
loading, installation
DIN 82004-1-2008 带椭圆孔眼、双耳和圆孔眼接头配件的松紧螺丝扣.第1部分:非合金质量钢
Turnbuckles with oval eyes, double lugs and
round eyes head fittings - Part 1: Non-alloy
quality steel
DIN 82004-2-2008 带椭圆形孔眼、双耳和圆形孔眼接头配件的松紧螺丝扣.第2部分:不锈钢
Turnbuckles with oval eyes, double lugs and
round eyes head fittings - Part 2: Stainless
steel
DIN 82006-1-2008 带螺纹柄的椭圆形孔眼接头配件.第1部分:旋转接头和松紧螺丝扣用非合金质量钢
Oval eye head fittings with threaded shank -
Part 1: For swivels and turnbuckles, non-alloy
quality steel
DIN 82006-2-2008 带螺纹柄的椭圆形孔眼接头配件.第2部分:松紧螺丝扣用不锈钢
Oval eye head fittings with threaded shank -
Part 2: For turnbuckles, stainless steel
DIN 82008-1-2008 带螺纹柄的双耳接头配件.第1部分:旋转接头和松紧螺丝扣用非合金质量钢
Double lug head fittings with threaded shank
- Part 1: For swivels and turnbuckles, non-alloy
quality steel
DIN 82008-2-2008 带螺纹柄的双耳接头配件.第2部分:松紧螺丝扣用不锈钢
Double lug head fittings with threaded shank
- Part 2: For turnbuckles, stainless steel
DIN 82010-1-2008 带螺柄的螺柱孔眼配件.第1部分:旋转接头和松紧螺丝扣用非合金质量钢
Stud-eye head fittings with threaded shank -
Part 1: For swivels and turnbuckles, non-alloy
quality steel
DIN 82048-1990 跨距万向接头双叉件 Double yoke pieces
for span trunnion
DIN 8526-1977 钎焊接头检验.接缝钎焊接头、剪切试验、蠕变剪切试验 Testing
of Soldering Joints; Gap Soldered Joints, Shear
Test, Creep Shear Test
DIN 86041-2-1996 焊接法兰.第2部分:舷外接头.公称压力10、16、40
Welding flanges - Part 2: Outboard connections,
nominal pressure 10, 16, 40
DIN 86103-1996 公制细螺纹和惠氏管螺纹管接头用分岔接管 Sockets for
screwed ends with metric fine thread and Whitworth
pipe thread
DIN 86126-2000 船舶用压合接头.公制螺纹24级接头.类型和尺寸 Compression
fittings for shipboard use - 24° fittings with
metric thread - Types and dimensions
DIN 86127-2000 舰船用压缩式接头.米制螺纹24级接头.技术规范 Compression
fittings for shipboard use - 24 fittings with
metric thread - Technical specification
DIN 86200-1989 灭火和甲板冲洗设备.软管接头.管件.软管.附件.造船用各类管件产品概要
Fire extinguishing and wash deck installation;
hose couplings, armatures, hoses, accessories;
summary of types for shipbuilding
DIN 86204-1993 船舶用黄铜制公称压力16的C型整体消防软管接头 Solid
fire hose coupling type C, PN 16; made of brass,
for use on ships
DIN 86205-1993 船舶用黄铜制公称压力16的B型整体消防软管接头 Solid
fire hose coupling type B, PN 16; made of brass
for use on ships
DIN 86211-1991 公称压力（PN）16、带C或B型消防软管管接头和带法兰连接的灭火阀
Fire valves for PN 16, with fire hose couplings
type C or B and with flange connection
DIN 86284-1997 饮用水、灭火水、污水、油和含油混合剂的输送和接受用管接头类型.概要
Types of joints for disposal and refuelling
of drinking water, fire fighting water, sewage,
oil and oily mixtures - Synopsis
DIN 86287-1999 船舶和海上建筑结构的管道.带插接口和插套的钢管和管接头.铺设和处理
Pipework on ships and marine structures - Steel
pipes and fittings with spigot and socket -
Laying and treatment
DIN 87343-1976 手动带传动管的遥控传动装置.焊入接头的叉形联杆 Remote
control gear with transmission tubing for manual
operation; fork links for welding-in connection
DIN 8906-1990 制冷系统用40公称压力扩口法兰的非钎焊接压紧管接头 PN 40
flared flange solderless compression couplings
for use in refrigerating systems
DIN 8912-1990 制冷系统用40公称压力扩口法兰的非钎焊接压紧管接头用的接头螺母和螺纹堵塞
Coupling nuts and screwed plugs for use with
PN 40 flared flange solderless compression couplings
in refrigerating systems
DIN 8914-1990 制冷系统用40公称压力扩口法兰的非钎焊接压紧管接头用的90°锥体密封环和密封盖
90° tapered seal rings and caps for use with
PN 40 flared flange solderless compression couplings
in refrigerating systems
DIN 9798-1980 食品加工机械.灌香肠机.灌料管和灌料接头 Food equipment;
sausage stuffers, filling horns and connections
DIN EN 10242-1995 可锻铸铁螺纹管管接头 Threaded pipe fittings
in malleable cast iron; German version EN 10242:1994
DIN EN 10242/A1-1999 可锻铸铁螺纹管管接头.修正A1 Threaded
pipe fitting in malleable cast iron; Amendment
A1; German version EN 10242:1994/A1:1999
DIN EN 10311-2005 水和其他含水液体传送用钢管和配件的连接用接头 Joints
for the connection of steel tubes and fittings
for the conveyance of water and other aqueous
liquids; German version EN 10311:2005
DIN EN 1075-2000 木质构件.试验方法.金属板冲压紧固件连接接头 Timber
structures - Test methods - Joints made with
punched metal plate fasteners; German version
EN 1075:1999
DIN EN 12061-1999 塑料管道系统.热塑管接头.耐冲击性能试验方法 Plastics
piping systems - Thermoplastics fittings - Test
method for impact resistance; German version
EN 12061:1999
DIN EN 12295-1999 塑料管道系统.热水和冷水用热塑性塑料管和相关管件.管接头耐循环压力的检测方法
Plastics piping systems - Thermoplastics pipes
and associated fittings for hot and cold water
- Test methods for resistance of joints to pressure
cycling; German version EN 12295:1999
DIN EN 12512-2005 木结构.试验方法.机械紧固件接头的循环试验 Timber
structures - Test methods - Cyclic testing of
joints made with mechanical fasteners; English
version of DIN EN 12512:2001 + A1:2005
DIN EN 12517-1-2006 焊接连接的无损试验.第1部分:通过X光透视评定钢、镍、钛及其合金焊接接头.允许极限
Non-destructive testing of welds - Part 1: Evaluation
of welded joints in steel, nickel, titanium
and their alloys by radiography - Acceptance
levels; English version of DIN EN 12517-1:2006-06
DIN EN 12517-2-2008 接头的无损检验.第2部分:通过射线照相术评估铝及铝合金的焊接接头.验收等级
Non-destructive testing of welds - Part 2: Evaluation
of welded joints in aluminium and its alloys
by radiography - Acceptance levels; English
version of DIN EN 12517-2:2008-12
DIN EN 1254-4-1998 铜和铜合金.管配件.第4部分:把其它连接端头和毛细管或压力接头相连接的管件
Copper and copper alloys - Plumbing fittings
- Part 4: Fittings combining other end connections
with capillary or compression ends; German version
EN 1254-4:1998
DIN EN 12560-1-2001 法兰及其接头.分级标识法兰用垫圈.第1部分:有或无插件的非金属平垫圈
Flanges and their joints - Gaskets for class-designated
flanges - Part 1: Non-metallic flat gaskets
with or without inserts; German version EN 12560-1:2001
DIN EN 12560-2-2001 法兰及其接头.分级标识法兰用垫圈.第2部分:钢法兰用绕制螺旋形密封垫
Flanges and their joints - Gaskets for class-designated
flanges - Part 2: Spiral wound gaskets for use
with steel flanges; German version EN 12560-2:2001
DIN EN 12560-3-2001 法兰及其接头.分级标识法兰用垫圈.第3部分:非金属PTFE包封垫圈
Flanges and their joints - Gaskets for class-designated
flanges - Part 3: Non-metallic PTFE envelope
gaskets; German version EN 12560-3:2001
DIN EN 12560-4-2001 法兰及其接头.分级标识法兰用垫圈.第4部分:钢法兰用波纹形、平的或开槽的金属和嵌条金属垫圈
Flanges and their joints - Gaskets for class-designated
flanges - Part 4: Corrugated, flat or grooved
metallic and fillet metallic gaskets for use
with steel flanges; German version EN 12560-4:2001
DIN EN 12560-5-2001 法兰及其接头.分级标识法兰用垫圈.第5部分:钢法兰用金属环接头垫圈
Flanges and their joints - Gaskets for class-designated
flanges - Part 5: Metallic ring-joint gaskets
for use with steel flanges; German version EN
12560-5:2001
DIN EN 12560-6-2004 法兰及其接头.分级标示法兰用垫圈.第6部分:钢法兰用涂覆的有锯齿金属垫圈
Flanges and their joints - Gaskets for class-designated
flanges - Part 6: Covered serrated metal gaskets
for use with steel flanges; German version EN
12560-6:2003
DIN EN 12560-7-2004 法兰及其接头.等级标示法兰用垫圈.第7部分:与钢法兰一起使用的金属涂覆有套垫圈
Flanges and their joints - Gaskets for Class
designated flanges - Part 7: Covered metal jacketed
gaskets for use with steel flanges; German version
EN 12560-7:2004
DIN EN 12797-2000 钎焊.钎焊接头的破坏试验 Brazing - Destructive
tests of brazed joints; German version EN 12797:2000
DIN EN 12799-2000 钎焊.钎焊接头的无损检验 Brazing - Non-destructive
examination of brazed joints; German version
EN 12799:2000
DIN EN 12814-1-1999 热塑性塑料半成品焊接接头的试验.第1部分:弯曲试验
Testing of welded joints of thermoplastics semi-finished
products - Part 1: Bend test; German version
EN 12814-1:1999
DIN EN 12814-2-2000 热塑性塑料半成品的焊接接头试验.第2部分:拉伸试验.德文版本EN
12814-2:2000 Testing of welded joints of thermoplastics
semi-finished products - Part 2: Tensile test;
German version EN 12814-2:2000
DIN EN 12814-3-2005 热塑性半成品的焊接接头试验.第3部分:拉伸蠕变试验
Testing of welded joints of thermoplastics semi-finished
products - Part 3: Tensile creep test (including
amendment A1:2005); English version of DIN EN
12814-3:2000 + A1:2005
DIN EN 12814-4-2001 热塑性半成品焊接接头试验.第4部分:剥离试验 Testing
of welded joints of thermoplastics semi-finished
products - Part 4: Peel test; German version
EN 12814-4:2001
DIN EN 12814-5-2000 热塑性塑料半成品的焊接接头试验.第5部分:宏观检查
Testing of welded joints of thermoplastics semi-finished
products - Part 5: Macroscopic examination;
German version EN 12814-5:2000
DIN EN 12814-6-2000 热塑性塑料半成品的焊接接头试验.第6部分:低温拉伸试验
Testing of welded joints of thermoplastics semi-finished
products - Part 6: Low temperature tensile test;
German version EN 12814-6:2000
DIN EN 12814-7-2003 热塑半成品焊接接头试验.第7部分:腰形试验样品抗拉试验
Testing of welded joints of thermoplastics semi-finished
products - Part 7: Tensile test with waisted
test specimens; German version EN 12814-7:2002
DIN EN 12814-8 Berichtigung 1-2004 热塑性半成品焊接接头的检验.第8部分:要求
Testing of welded joints of thermoplastic semi-finished
products - Part 8: Requirements; German version
EN 12814-8:2001
DIN EN 12814-8-2001 热塑性半成品焊接接头试验.第8部分:要求 Testing
of welded joints of thermoplastic semi-finished
products - Part 8: Requirements; German version
EN 12814-8:2001
DIN EN 1306-1996 内河航运船只.污水排放接头 Inland navigation
vessels - Connections for the discharge of waste
water; German version EN 1306:1996
DIN EN 13090-2001 建筑物燃气管道螺纹接头再密封方法 Means for
resealing threaded joints of gas pipework in
buildings; German version EN 13090:2000
DIN EN 13100-1-2000 热塑性塑料半成品焊接接头的无损检验.第1部分:外观检验
Non destructive testing of welded joints of
thermoplastics semi-finished products - Part
1: Visual examination; German version EN 13100-1:1999
DIN EN 13100-2-2005 热塑性半成品焊接接头的无损检验.第2部分:X射线照相检验
Non-destructive testing of welded joints of
thermoplastics semi-finished products - Part
2: X-ray radiographic testing; German version
EN 13100-2:2004
DIN EN 13100-3-2005 热塑性半成品焊接接头的无损检验.第3部分:超声检验
Non-destructive testing of welded joints in
thermoplastics semi-finished products - Part
3: Ultrasonic testing; German version EN 13100-3:2004
DIN EN 14325-2004 化学防护服.化学防护服材料、接缝、接头及总体的试验方法和性能分类
Protective clothing against chemicals - Test
methods and performance classification of chemical
protective clothing materials, seams, joins
and assemblages; German version EN 14325:2004
DIN EN 1435-2002 焊缝的无损检验.焊接接头的X光照相检验; 德文版本 EN
1435:1997 + A1:2002 Non-destructive testing
of welds - Radiographic testing of welded joints;
German version EN 1435:1997 + A1:2002
DIN EN 14420-4-2007 带夹具的软管配件.第4部分:法兰接头 Hose
fittings with clamp units - Part 4: Flange connections;
English version of DIN EN 14420-4:2007-04
DIN EN 14420-6-2007 带夹具的软管配件.第6部分:TW油罐车接头 Hose
fittings with clamp units - Part 6: TW tank
truck couplings (includes Amendment A1:2007);
English version of DIN EN 14420-6:2004+A1:2007-04
DIN EN 14420-7-2007 带夹件的软管配件.第7部分:凸轮锁紧接头 Hose
fittings with clamp units - Part 7: Cam locking
couplings (includes Amendment A1:2007); English
version of DIN EN 14420-7:2007-04
DIN EN 14420-8-2007 带夹具的软管配件.第8部分:对称半节管接头(吉尔曼系统)
Hose fittings with clamp units - Part 8: Symmetrical
half coupling (Guillemin system) (includes Amendment
A1:2007); English version of DIN EN 14420-8:2007-04
DIN EN 14454-2005 防饮用水回流污染的装置.软管接头防回流装置DN 15至DN
32. A型H系列 Devices to prevent pollution by backflow
of potable water - Hose union backflow preventer
DN 15 to DN 32 - Family H; type A; German version
EN 14454:2005
DIN EN 1451-1-1999 建筑物结构体中的废水和污物排放系统用塑料管道系统(低温和高温).聚丙烯(PP).第1部分:管、管接头和管道系统
Plastics piping systems for soil and waste discharge
(low and high temperature) within the building
structure - Polypropylene (PP) - Part 1: Specifications
for pipes, fittings and the system; German version
EN 1451-1:1998
DIN EN 14525-2005 不同材料(球墨铸铁、灰铸铁、钢、PVC-U、PE和纤维水泥)管道用球墨铸铁大公差联接器和法兰接头
Ductile iron wide tolerance couplings and flange
adaptors for use with pipes of different materials:
Ductile iron, grey iron, steel, PVC-U, PE, fibre-cement;
German version EN 14525:2004
DIN EN 14741-2006 热塑管和管道系统.地下非压力设施用接头.通过评估密封压力测定弹性密封件接头的长期密封性能的试验方法
Thermoplastics piping and ducting systems -
Joints for buried non-pressure applications
- Test method for the long-term sealing performance
of joints with elastomeric seals by estimating
the sealing pressure English version of DIN
EN 14741:2006-05
DIN EN 15096-2008 饮用水防回流污染的装置.水龙带接头反真空阀.DN15～DN25包括家用H、B和D型.通用技术规范
Devices to prevent pollution by backflow of
potable water - Hose Union anti-vacuum valves
- DN 15 to DN 25 inclusive Family H, type B
and type D - General technical specification;
English version of DIN EN 15096:2008-04
DIN EN 1591-1 Bb.1-2001 法兰及其接头.密封圈法兰接头设计规则.背景信息
Flanges and their joints - Design rules for
gasketed circular flange connections - Background
information
DIN EN 1591-2-2008 法兰及其接头.带衬垫的圆形法兰接头设计规则.第2部分:衬垫参数
Flanges and their joints - Design rules for
gasketed circular flange connections - Part
2: Gasket parameters; English version of DIN
EN 1591-2:2008-09
DIN EN 1712-2002 焊缝的无损检验.焊接接头的超声波检验.验收标准; 德文版本
EN 1712:1997 + A1:2002 Non-destructive testing
of welds - Ultrasonic testing of welded joints
- Acceptance levels; German version EN 1712:1997
+ A1:2002
DIN EN 1714-2002 焊缝的无损检验.焊接接头的超声波检验; 德文版本 EN
1714:1997 + A1:2002 Non-destructive testing
of welds - Ultrasonic testing of welded joints;
German version EN 1714:1997 + A1:2002
DIN EN 175301-803-2007 详细规范:不可分的0.8mm 厚自锁螺纹的扁接头矩形连接器
Detail Specification: Rectangular connectors
- Flat contacts, 0,8 mm thickness, locking screw
not detachable; German version EN 175301-803:2006
DIN EN 1759-3-2004 法兰及其接头.等级标示的管、阀、配件和附件用圆形法兰.第3部分:铜合金法兰
Flanges and their joints - Circular flanges
for pipes, valves, fittings and accessories,
Class designated - Part 3: Copper alloy flanges;
German version EN 1759-3:2003 + AC:2004
DIN EN 1759-4-2003 法兰及其接头.指定类别的管、阀、配件和附件用圆形法兰.第4部分:铝合金法兰
Flanges and their joints - Circular flanges
for pipes, valves, fittings and accessories,
Class designated - Part 4: Aluminium alloy flanges;
German version EN 1759-4:2003
DIN EN 1993-1-8-2005 欧洲法规3:钢结构的设计.第1-8部分:接头的设计
Eurocode 3: Design of steel structures - Part
1-8: Design of joints; German Version EN 1993-1-8;2005
DIN EN 205-2003 胶粘剂.非结构上用木材胶粘剂.搭接接头的抗拉伸剪切强度的测定
Adhesives - Wood adhesives for non-structural
applications - Determination of tensile shear
strength of lap joints; German version EN 205:2003
DIN EN 2290-1-1998 航空航天系列.可调节控制杆端部接头的铝合金飞行控制杆体.第1部分:尺寸和负载
Aerospace series - Rod bodies flight control
in aluminium alloy, for adjustable end fittings
- Part 1: Dimensions and loads; German version
EN 2290-1:1998
DIN EN 2569-1992 航空航天系列.操纵钢缆接头和松紧螺丝扣.技术规范 Aerospace
series; control cable fittings and turnbarrels;
technical specification; german version EN 2569:1991
DIN EN 2591-512-2003 航空航天系列.光电连接元件.试验方法.第512部分:密封连接器外壳固定接头有效性
Aerospace series - Elements of electrical and
optical connection; Test methods - Part 512:
Effectiveness of non-removable fixing of hermetically
sealed connector shell; German and English version
EN 2591-512:2002
DIN EN 274-1-2002 洁具下水管接头.第1部分:要求 Waste fittings
for sanitary appliances - Part 1: Requirements;
German version EN 274-1:2002
DIN EN 274-2-2002 洁具下水管接头.第2部分:试验方法 Waste fittings
for sanitary appliances - Part 2: Test methods;
German version EN 274-2:2002
DIN EN 274-3-2002 洁具下水管接头.第3部分:质量控制 Waste fittings
for sanitary appliances - Part 3: Quality control;
German version EN 274-3:2002
DIN EN 295-4-1995 排水和污水用陶土管和配件及管接头.第4部分:专用配件、转换接头和相容附件的要求
Vitrified clay pipes and fittings and pipe joints
for drains and sewers - Part 4: Requirements
for special fittings, adapters and compatible
accessories; German version EN 295-4:1995
DIN EN 295-7-1995 陶土污水管.配件及管连接件.第7部分:陶土管和管接头前移要求
Vitrified clay pipes and fittings and pipe joints
for drains and sewers - Part 7: Requirements
for vitrified clay pipes and joints for pipe
jacking; German version EN 295-7:1995
DIN EN 301006-1-2000 模拟和综合业务数字网(ISDN)用户线路的电路试验用局域交换Q3接口.第1部分:Q3接头规范
Q3 interface at the Local Exchange (LE) for
line and circuit testing of analogue and Integrated
Services Digital Network (ISDN) subscriber lines
- Part 1: Q3 interface specification (Endorsement
of the English version EN 301006-1 V 1.2.3 (1998-10)
as German Standard)
DIN EN 3080-2007 航空航天系列.钛合金8°30'管接头.带有推力线螺母的缩短三通
Aerospace series - Pipe coupling 8°30' in titanium
alloy - Tees, reduced, branch with thrust wire
nut; German and English version EN 3080:2006
DIN EN 3082-2004 航空航天系列.钛合金管连接件8°30'.修理用闷头焊接活接头
Aerospace series - Pipe coupling 8°30 in titanium
alloy - Unions, bulkhead welded end, for repair;
German and English version EN 3082:2001 + AC:2003
DIN EN 3083-2004 航空航天系列.钛合金管连接件8°30'.修理用闷头长焊接端头活接头
Aerospace series - Pipe coupling 8°30 in titanium
alloy - Unions, bulkhead, long welded end, for
repair; German and English version EN 3083:2001
+ AC:2003
DIN EN 3084-2004 航空航天系列.钛合金管连接件8°30'.修理用焊接端头螺纹活接头
Aerospace series - Pipe coupling 8°30 in titanium
alloy - Unions, welded end threaded for repair;
German and English version EN 3084:2001 + AC:2003
DIN EN 3244-2002 航空航天系列.钛合金8°30'管连接件.双端管接头 Aerospace
series - Pipe coupling 8°30 in titanium alloy
- Unions, double ended; German version EN 3244:2001
DIN EN 3245-2002 航空航天系列.钛合金8°30'管连接件.异径管接头;
德文版本 EN 3245:2001 Aerospace series - Pipe coupling
8°30 in titanium alloy - Unions, reducer; German
version EN 3245:2001
DIN EN 3246-2002 航空航天系列.钛合金8°30'管连接件.闷头管接头;
德文版本 EN 3246:2001 Aerospace series - Pipe coupling
8°30 in titanium alloy - Unions, bulkhead; German
version EN 3246:2001
DIN EN 3247-2002 航空航天系列.钛合金8°30'管连接件.焊接端的闷头管接头;
德文版本 EN 3247:2001 Aerospace series - Pipe coupling
8°30 in titanium alloy - Unions, bulkhead, welded
end; German version EN 3247:2001
DIN EN 3269-2006 航空航天系列.8°30'钛合金管接头.带动态梁密封端的单头卡套.德文和英文版本EN
3269-2001 Aerospace series - Pipe coupling 8°30'
in titanium alloy - Ferrules, blind, with dynamic
beam seal end; German and English version EN
3269:2001
DIN EN 3272-2006 航空航天系列.8°30'管接头.焊接箍用动态梁密封端.几何构型.德文和英文版本EN
3272-2001 Aerospace series - Pipe coupling 8°30'
- Dynamic beam seal end for ferrule, welded
- Geometric configuration; German and English
version EN 3272:2001
DIN EN 3373-001-2008 航空航天系列.导电体压接端头和内嵌式接头.第001部分:技术规范
Aerospace series - Terminal lugs and in-line
splices for crimping on electric conductors
- Part 001: Technical specification; German
and English version EN 3373-001:2007
DIN EN 3566-2004 航空航天系列.钛合金管连接件8°30'.带锁紧环的接头
Aerospace series - Pipe coupling 8°30 in titanium
alloy - Adaptors with lockring; German and English
version EN 3566:2001 + AC:2003
DIN EN 3690-2004 航空航天系列.钛合金管连接件8°30'.长闷头活接头
Aerospace series - Pipe coupling 8°30 in titanium
alloy - Unions, bulkhead, long; German and English
version EN 3690:2001 + AC:2003
DIN EN 3691-2004 航空航天系列.钛合金管连接件8°30'.焊接端长闷头活接头
Aerospace series - Pipe coupling 8°30 in titanium
alloy - Unions, bulkhead, long, welded end;
German and English version EN 3691:2001 + AC:2003
DIN EN 3851-2004 航空航天系列.钛合金TI-P64001的60球面管子接头.直转动螺套
Aerospace series - Pipe couplings, 60°, spherical,
in titanium alloy TI-P64001 - Swivel nut, straight;
German and English version EN 3851:2003
DIN EN 3852-2004 航空航天系列.钛合金TI-P64001的60球面管子接头.有螺纹的焊接直活管节
Aerospace series - Pipe couplings, 60°, spherical,
in titanium alloy TI-P64001 - Straight unions,
welded, threaded; German and English version
EN 3852:2002
DIN EN 3853-2004 航空航天系列.钛合金TI-P64001的60球面管子接头.有螺纹直活管节
Aerospace series - Pipe couplings, 60°, spherical,
in titanium alloy TI-P64001 - Straight unions,
threaded; German and English version EN 3853:2002
DIN EN 3854-2004 航空航天系列.钛合金TI-P64001的60球面管子接头.焊接套圈
Aerospace series - Pipe couplings, 60°, spherical,
in titanium alloy TI-P64001 - Ferrules, welded;
German and English version EN 3854:2002
DIN EN 3855-2004 航空航天系列.钛合金TI-P64001的60球面管子接头.帽
Aerospace series - Pipe couplings, 60°, spherical,
in titanium alloy TI-P64001 - Caps; German and
English version EN 3855:2002
DIN EN 3856-2004 航空航天系列.钛合金TI-P64001的60球面管子接头.推力线用转动螺套
Aerospace series - Pipe couplings, 60°, spherical,
in titanium alloy TI-P64001 - Swivel nuts for
thrust wire; German and English version EN 3856:2002
DIN EN 3857-2004 航空航天系列.钛合金TI-P64001的60球面管子接头.90焊接弯头
Aerospace series - Pipe couplings, 60°, spherical,
in titanium alloy TI-P64001 - Elbows 90°, welded;
German and English version EN 3857:2002
DIN EN 387-2002 胶合板.大尺寸指形接头.性能要求和最低生产要求 Glued
laminated timber - Large finger joints - Performance
requirements and minimum production requirements;
German version EN 387:2001
DIN EN 4020-2006 航空航天系列. 8°30'钛合金管接头.带推进线螺母的90°弯头焊接端
Aerospace series - Pipe coupling 8°30 in titanium
alloy - Elbows 90°, welded end with thrust wire
nut; German and English version EN 4020:2001
DIN EN 4025-2006 航空航天系列. 8°30'钛合金管接头.45°凸檐弯头
Aerospace series - Pipe coupling 8°30′ in titanium
alloy - Elbows 45°, bulkhead; German and English
version EN 4025:2001
DIN EN 4028-2008 航空航天系列.钛合金中8°30′管接头.运转中带止推金属丝螺母的三通管
Aerospace series - Pipe coupling 8°30 in titanium
alloy - Tees with thrust wire nut on run; German
and English version EN 4028:2001
DIN EN 4051-2003 航空航天系列.钛合金TI-P64001、球形、60度管连接器.油口接头
Aerospace series - Pipe couplings, 60°, spherical,
in titanium alloy TI-P64001 - Port connection;
German and English version EN 4051:2002
DIN EN 4186-2002 航空航天系列.钛合金管连接件 8°30'.十字形管接头;
德文版本 EN 4186:2001 Aerospace series - Pipe coupling
8°30 in titanium alloy - Unions, cross; German
version EN 4186:2001
DIN EN 4187-2006 航空航天系列.8°30'钛合金管接头.90°闷头长弯管
Aerospace series - Pipe coupling 8°30′ in titanium
alloy - Elbows 90° bulkhead, long; German and
English version EN 4187:2001
DIN EN 4233-2002 航空航天系列.钛合金管连接件 8°30'.带螺纹的焊接管接头;
德文版本 EN 4233:2001 Aerospace series - Pipe coupling
8°30 in titanium alloy - Unions, welded, threaded;
German version EN 4233:2001
DIN EN 4550-3-2004 航空航天系列.管道连接件37设计构造.英制.第3部分:端口接头
Aerospace series - Pipe coupling 37° - Design
configuration - Inch series - Part 3: Port connections;
German and English version EN 4550-3:2003
DIN EN 4552-2004 航空航天系列.耐热钢制37球面管子接头.焊接端直螺纹接头.英制系列
Aerospace series - Pipe coupling, 37°, spherical,
in heat resisting steel - Straight nipples,
welded end - Inch series; German and English
version EN 4552:2003
DIN EN 4553-2004 航空航天系列.耐热钢制37球面管子接头.焊接端90弯管螺纹接头.英制系列
Aerospace series - Pipe coupling 37°, spherical,
in heat resisting steel - Elbow 90° nipples,
welded end - Inch series; German and English
version EN 4553:2003
DIN EN 4554-2004 航空航天系列.耐热钢制37球面管子接头.加螺纹直活管节.英制系列
Aerospace series - Pipe coupling 37°, spherical,
in heat resisting steel - Straight unions, threaded
- Inch series; German and English version EN
4554:2003
DIN EN 4555-2004 航空航天系列.耐热钢制37球面管子接头.焊接端套圈.英制系列
Aerospace series - Pipe coupling 37°, in heat
resisting steel - Ferrules, welded end - Inch
series; German and English version EN 4555:2003
DIN EN 4556-2004 航空航天系列.耐热钢制37球面管子接头.帽组件.英制系列
Aerospace series - Pipe coupling 37°, in heat
resisting steel - Cap assemblies - Inch series;
German and English version EN 4556:2003
DIN EN 4557-2004 航空航天系列.耐热钢制37球面管子接头.焊接端T形螺纹接头.英制系列
Aerospace series - Pipe couplings, 37°, spherical,
in heat resisting steel - Tees nipples, welded
end - Inch series; German and English version
EN 4557:2003
DIN EN 4561-2004 航空航天系列.耐热钢制焊接管子接头.90弯管.英制系列
Aerospace series - Pipe coupling, welded, in
heat resisting steel - Elbow 90° - Inch series;
German and English version EN 4561:2003
DIN EN 4562-2004 航空航天系列.耐热钢制焊接管子接头.异径管.英制系列
Aerospace series - Pipe coupling, welded, in
heat resisting steel - Reductors - Inch series;
German and English version EN 4562:2003
DIN EN 4563-2004 航空航天系列.耐热钢制焊接管子接头.三通.英制系列 Aerospace
series - Pipe coupling, welded, in heat resisting
steel - Tees - Inch series; German and English
version EN 4563:2003
DIN EN 50377-2-1-2002 光纤通信系统接头组件和互连元件.产品规范.第2-1部分:端接在IEC
60793-2 B1类单模纤维上的FC-PC型接头组件 Connector sets and
interconnect components to be used in optical
fibre communication systems - Product specifications
- Part 2-1: Type FC-PC terminated on IEC 60793-2
category B1 singlemode fibre; German version
EN 50377-2-1:2001
DIN EN 512/A1-2002 纤维水泥制品.压力管道和接头.修改件A1:2001;
德文版本 EN 512:1994/A1:2001 Fibre-cement products
- Pressure pipes and joints; Amendment A1:2001;
German version EN 512:1994/A1:2001
DIN EN 545-2007 水管用球墨铸铁管、配件、附件及其接头.要求和试验方法 Ductile
iron pipes, fittings, accessories and their
joints for water pipelines - Requirements and
test methods; English version of DIN EN 545:2007-02
DIN EN 60512-16-13-2009 电子设备用连接器.试验和测量.第16-13部分:触点和终端的机械试验.试验16m:无钎焊缠绕接头的退绕能力
Connectors for electronic equipment - Tests
and measurements - Part 16-13: Mechanical tests
on contacts and terminations - Test 16m: Un-wrapping,
solderless wrapped connections (IEC 60512-16-13:2008);
German version EN 60512-16-13:2008
DIN EN 61466-1-1997 额定电压超过1KV的架空线用复合绝缘子串组合件.第1部分:标准强度等级和端接头
Composite string insulator units for overhead
lines with a nominal voltage greater than 1
kV - Part 1: Standard strength classes and end
fittings (IEC 61466-1:1997); German version
EN 61466-1:1997
DIN EN 639-1994 包括管接头和配件的混凝土承压管通用要求 Common requirements
for concrete pressure pipes, including joints
and fittings; German version EN 639:1994
DIN EN 712-1994 热塑塑料管道系统.压力管和管接头之间承载端部的机械连接.恒定纵向作用力下抗拉出力的试验方法
Thermoplastics piping systems; end-load bearing
mechanical joints between pressure pipes and
fittings; test method for resistance to pull-out
under constant longitudinal force; German version
EN 712:1993
DIN EN 713-1994 塑料管道系统.管接头和聚烯烃压力管间的机械连接.在内压和弯曲下密封性的试验方法
Plastics piping systems; mechanical joints between
fittings and polyolefin pressure pipes; test
method for leaktightness under internal pressure
of assemblies subjected to bending; German version
EN 713:1993
DIN EN 715-1994 热塑塑料管道系统.小直径压力管和管接头之间承载端部的连接.在水内压力下（包括端头推力）密封试验方法
Thermoplastics piping systems; end-load bearing
joints between small diameter pressure pipes
and fittings; test method for leaktightness
under internal water pressure, including end
thrust; German version EN 715:1994
DIN EN 728-1997 塑料管和管道系统.聚烯烃管和接头.氧化感应时间测定 Plastics
piping and ducting systems - Polyolefin pipes
and fittings - Determination of oxidation induction
time; German version EN 728:1997
DIN EN 876-1995 金属材料焊接的破坏试验.有熔焊接头的焊接金属的纵向拉伸试验
Destructive tests on welds in metallic materials
- Longitudinal tensile test on weld metal in
fusion welded joints; German version EN 876:1995
DIN EN 911-1995 塑料管道系统.热塑塑料压力管道用的弹性密封环型接头和机械接头的连接.外部静力液压条件下的防漏试验方法;
Plastics piping systems - Elastomeric sealing
ring type joints and mechanical joints for thermoplastics
pressure piping - Test method for leaktightness
under external hydrostatic pressure; German
version EN 911:1995
DIN EN ISO 10042-2006 焊接.铝和铝合金的弧焊接头.缺陷质量分级 (ISO
10042-2005).德文版本 EN ISO 10042-2005 Welding -
Arc-welded joints in aluminium and its alloys
- Quality levels for imperfections (ISO 10042:2005);
English version of DIN EN ISO 10042:2006-02
DIN EN ISO 10321-2008 土工布.用宽条法对接头/接缝处的拉伸试验 Geosynthetics
- Tensile test for joints/seams by wide-width
strip method (ISO 10321:2008); German version
EN ISO 10321:2008
DIN EN ISO 10692-1-2003 储气瓶.微电子工业用储气瓶阀接头.第1部分:输出口接头
Gas cylinders - Gas cylinder valve connections
for use in the microelectronic industry - Part
1: Outlet connections (ISO 10692-1:2001); German
version EN ISO 10692-1:2001
DIN EN ISO 10692-2-2003 储气瓶.微电子工业用储气瓶阀接头.第2部分:储气瓶阀接头规范和型式试验
Gas cylinders - Gas cylinder valve connections
for use in the microelectronic industry - Part
2: Specification and type testing for valve
to cylinder connections (ISO 10692-2:2001);
German version EN ISO 10692-2:2001
DIN EN ISO 11144-1996 牙科设备.给排水管接头 Dental equipment
- Connections for supply and waste lines (ISO
11144:1995); German version EN ISO 11144:1996
DIN EN ISO 1167-1-2006 流体传输用热塑管、接头和组件.抗内压力的测定.第1部分:通用方法
Thermoplastics pipes, fittings and assemblies
for the conveyance of fluids - Determination
of the resistance to internal pressure - Part
1: General method (ISO 1167-1:2006); English
version of DIN EN ISO 1167-1:2006-05
DIN EN ISO 1167-2-2006 流体传输用热塑管、接头和组件.抗内压力的测定.第2部分:管试件的准备
Thermoplastics pipes, fittings and assemblies
for the conveyance of fluids - Determination
of the resistance to internal pressure - Part
2: Preparation of pipe test pieces (ISO 1167-2:2006);
English version of DIN EN ISO 1167-2:2006-05
DIN EN ISO 13919-1-1996 焊接.电子和激光束焊接接头.质量缺陷等级指南.第1部分:钢
Welding - Electrons and laser beam welded joints;
guidance on quality levels for imperfections
- Part 1: Steel (ISO 13919-1:1996); German version
EN ISO 13919-1:1996
DIN EN ISO 13919-2-2001 焊接.电子和激光束焊接接头.质量缺陷等级导则.第1部分:铝及可焊铝合金
Welding - Electron and laser beam welded joints;
Guidance on quality levels for imperfections
- Part 2: Aluminium and its weldable alloys
(ISO 13919-2:2001); German version EN ISO 13919-2:2001
DIN EN ISO 14324-2003 电阻点焊.焊接的有损检验.点焊接头的疲劳试验方法
Resistance spot welding - Destructive tests
of welds - Method for the fatigue testing of
spot welded joints (ISO 14324:2003); German
version EN ISO 14324:2003
DIN EN ISO 15236-4-2004 衬钢丝绳芯传送带.第4部分:硬化带接头
Steel cord conveyor belts - Part 4: Vulcanized
belt joints (ISO 15236-4:2004); German Version
EN ISO 15236-4:2004
DIN EN ISO 16070-2006 石油和天然气工业.下井设备.锁芯轴和落地接头
Petroleum and natural gas industries - Downhole
equipment - Lock mandrels and landing nipples
(ISO 16070:2005); English version EN ISO 16070:2005
DIN EN ISO 17659-2005 焊接.图示焊接接头的多语种术语 Welding
- Multilingual terms for welded joints with
illustrations (ISO 17659:2002); Trilingual version
EN ISO 17659:2004
DIN EN ISO 17660-1 Berichtigung 1-2007 焊接.钢筋焊接.第1部分:承载焊接接头(ISO
17660-1-2006) Welding - Welding of reinforcing
steel - Part 1: Load-bearing welded joints (ISO
17660-1:2006); German version EN ISO 17660-1:2006,
Corrigenda to DIN EN ISO 17660-1:2006-12
DIN EN ISO 17660-2 Berichtigung 1-2007 焊接.钢筋焊接.第2部分:非承载焊接接头(ISO
17660-2-2006) Welding - Welding of reinforcing
steel - Part 2: Non load-bearing welded joints
(ISO 17660-2:2006); German version EN ISO 17660-2:2006,
Corrigenda to DIN EN ISO 17660-2:2006-12
DIN EN ISO 18279-2004 铜焊.铜焊接头的缺陷 Brazing - Imperfections
in brazed joints (ISO 18279:2003); German version
EN ISO 18279:2003
DIN EN ISO 5183-1-2000 电阻焊接设备.外锥度1:10电极接头.第1部分:锥度1:10圆锥形接头
Resistance welding equipment - Electrode adaptors,
male taper 1:10 - Part 1: Conical fixing, taper
1:10 (ISO 5183-1:1998); German version EN ISO
5183-1:2000
DIN EN ISO 5183-2-2002 电阻点焊.外锥度1:10电极接头.第2部分:轴端推力电极用平行柄接头(ISO
5183-2:2000); 德文版本 EN ISO 5183- Resistance spot
welding - Electrode adaptors, male taper 1:10
- Part 2: Parallel shank fixing for end-thrust
electrodes (ISO 5183-2:2000); German version
EN ISO 5183-2:2002
DIN EN ISO 5356-1-2004 麻醉和呼吸设备.圆锥形接头.第1部分:锥体和锥套
Anaesthetic and respiratory equipment - Conical
connectors - Part 1: Cones and sockets (ISO
5356-1:2004); German version EN ISO 5356-1:2004
DIN EN ISO 5817 Berichtigung 1-2007 焊接.钢、镍、钛及其合金的熔焊接头(束焊除外).缺陷的质量等级.技术勘误DIN
EN ISO 5817-2006 Welding - Fusion-welded joints
in steel, nickel, titanium and their alloys
(beam welding excluded) - Quality levels for
imperfections (ISO 5817:2003 + Cor. 1:2006);
German version EN ISO 5817:2003 + AC:2006, Corrigenda
to DIN EN ISO 5817:2006-10
DIN EN ISO 5817-2006 焊接.钢、镍、钛及其合金的熔焊接头(束焊除外).缺陷的质量等级(ISO
5817-2003 + Cor.1-2006) Welding - Fusion-welded
joints in steel, nickel, titanium and their
alloys (beam welding excluded) - Quality levels
for imperfections (ISO 5817:2003 + Cor. 1:2006);
German version EN ISO 5817:2007
DIN EN ISO 6149-1-2007 用于液压传动和一般用途的管接头.带ISO
261米制螺纹和O形圈密封的端口和柱头螺栓端头.第1部分:锪孔沟槽中装 Connections
for hydraulic fluid power and general use -
Ports and stud ends with ISO 261 metric threads
and O-ring sealing - Part 1: Ports with truncated
housing for O-ring seal (ISO 6149-1:2006)English
version of DIN EN ISO 6149-1:2007-05
DIN EN ISO 6149-2-2007 用于液压传动和一般用途的管接头.带ISO
261米制螺纹和O形圈密封的端口和柱头螺栓端头.第2部分:重型(S系列) Connections
for hydraulic fluid power and general use -
Ports and stud ends with ISO 261 metric threads
and O-ring sealing - Part 2: Dimensions, design,
test methods and requirements for heavy-duty
(S series) stud ends (ISO 6149-2:2006)English
version of DIN EN ISO 6149-2:2007-05
DIN EN ISO 6149-3-2007 用于液压传动和一般用途的管接头.带ISO
261米制螺纹和O形圈密封的端口和柱头螺栓端头.第3部分:轻型(L系列) Connections
for hydraulic fluid power and general use -
Ports and stud ends with ISO 261 metric threads
and O-ring sealing - Part 3: Dimensions, design,
test methods and requirements for light-duty
(L series) stud ends (ISO 6149-3:2006)English
version of DIN EN ISO 6149-3:2007-05
DIN EN ISO 8092-3-1999 道路车辆.车载电气线束的连接.第3部分:多极连接接头,尺寸和特殊要求
Road vehicle - Connections for on-board electrical
wiring harnesses - Part 3: Tabs for multi-pole
connections, dimensions and specific requirements
(ISO 8092-3:1996); German version EN ISO 8092-3:1999
DIN EN ISO 8434-1-2008 液压传动和通用金属管连接件.第1部分:24°锥形接头
Metallic tube connections for fluid power and
general use - Part 1: 24 degree cone connectors
(ISO 8434-1:2007); German version EN ISO 8434-1:2007
DIN EN ISO 8795-2001 人类生活用水的塑料输水管道系统.偏移评定.塑料管、配件及其接头偏移值测定
Plastics piping systems for the transport of
water intended for human consumption - Migration
assessment - Determination of migration values
of plastics pipes and fittings and their joints
(ISO 8795:2001); German version EN ISO 8795:2001
DIN EN ISO 9093-1-1998 小型船舶.船底阀和船体外壳管接头.第1部分:金属件
Small craft - Seacocks and through-hull fittings
- Part 1: Metallic (ISO 9093-1:1994); German
version EN ISO 9093-1:1997
DIN EN ISO 9142-2004 胶粘剂.粘接接头测试用标准试验室老化条件的选择指南
Adhesives - Guide to the selection of standard
laboratory ageing conditions for testing bonded
joints (ISO 9142:2003); German version EN ISO
9142:2003
DIN EN ISO 9692-2-1999 焊接和相关工艺.接头的预处理.第2部分:钢的埋弧焊（ISO
9692-2-1998,包括技术勘误AC-1999) Welding and allied
processes - Joint preparation - Part 2: Submerged
arc welding of steels (ISO 9692-2:1998, includes
Corrigendum AC:1999); German version EN ISO
9692-2:1998 + AC:1999
DIN EN ISO 9692-4-2003 焊接和相关工艺.接头准备的推荐标准.第4部分:复合钢
Welding and allied processes - Recommendations
for joint preparation - Part 4: Clad steels
(ISO 9692-4:2003); German version EN ISO 9692-4:2003
DIN ISO 10583-1998 航空航天流体系统.管/管接头组件的试验方法 Aerospace
fluid systems - Test methods for tube/fitting
assemblies (ISO 10583:1993)
DIN ISO 12151-2-2004 液压传动和通用连接件.软管接头.第2部分:带ISO
8434-1和8434-4 24°锥形连接件末端和O形圈的软管接头 Connections
for hydraulic fluid power and general use -
Hose fittings - Part 2: Hose fittings with ISO
8434-1 and ISO 8434-4 24° cone connector ends
with O-rings (ISO 12151-2:2003)
DIN ISO 12151-3-2004 液压传动和通用连接件.软管接头.第3部分:带ISO
6162法兰末端的软管接头 Connections for hydraulic fluid
power and general use - Hose fittings - Part
3: Hose fittings with ISO 6162 flange ends (ISO
12151-3:1999)
DIN ISO 15171-1-2004 流体传动和一般用途管接头.诊断用液压管接头.第1部分:非压力下连接的管接头
Connections for fluid power and general use
- Hydraulic couplings for diagnostic purposes
- Part 1: Coupling not for connection under
pressure (ISO 15171-1:1999)
DIN ISO 15171-2-2004 流体传动和一般用途管接头.诊断用液压管接头.第2部分:带M12
2螺纹端的压力连接接头 Connections for fluid power and
general use - Hydraulic couplings for diagnostic
purposes - Part 2: Couplings with M 16 × 2 end
for connection under pressure (ISO 15171-2:2000)
DIN ISO 15407-1-2003 气压传动.五气口方向控制阀、规格18mm和26mm.第1部分:无电气接头的安装面
Pneumatic fluid power - Five-port directional
control valves, sizes 18 mm and 26 mm - Part
1: Mounting interface surfaces without electrical
connector (ISO 15407-1:2000)
DIN ISO 16030-2007 气压传动.接头.端口和柱头螺栓端头.(ISO 16030-2001+修改件1-2005)
Pneumatic fluid power - Connections - Ports
and stud ends (ISO 16030:2001 + Amd. 1:2005)English
version of DIN ISO 16030-2007-05
DIN ISO 22826-2008 金属材料焊缝的破坏性试验.使用激光和电子束焊接的窄接头硬度试验(维氏和努氏硬度试验)
Destructive tests on welds in metallic materials
- Hardness testing of narrow joints welded by
laser and electron beam (Vickers and Knoop hardness
tests) (ISO 22826:2005)
DIN ISO 5599-1-2005 气压传动.五气口方向控制阀.第1部分:不带电接头的安装面
Pneumatic fluid power - Five-port directional
control valves - Part 1: Mounting interface
surfaces without electrical connector (ISO 5599-1:2001);English
version of DIN ISO 5599-1:2005
DIN ISO 5620-1-1994 造船和船舶结构.饮用水箱注水接头.第1部分:一般要求;
等同采用 ISO 5620-1:1992 Shipbuilding and marine
structures; filling connection for drinking
water tanks; general requirements; identical
with ISO 5620-1:1992
DIN ISO 5620-2-1994 造船和船舶结构.饮用水箱注水接头.第2部分:部件;
等同采用 ISO 5620-2:1992 Shipbuilding and marine
structures; filling connection for drinking
water tanks; components; identical with ISO
5620-2:1992
DIN ISO 7803-1995 商用公路车辆.转向球形接头; 等同采用 ISO 7803:1987
Commercial road vehicles - Steering ball joints;
identical with ISO 7803:1987
DIN VDE 0710-11-1968 工作电压低于1kV的照明配件规范.第11部分:嵌入式信号灯接头规范规则
Specifications for lighting fittings with service
voltages below 1000 V; Specification rules for
flush-fitting signal-light fittings
欧洲接头标准(EN joint standards)
--------------------------------------------------------------------------------
编号 中文名称 英文名称
EN 1119-1996 塑料管道系统 玻璃增强热固塑料管和配件用接头 挠性和还原接合接头密封性和耐损伤性试验方法
Plastics piping systems - Joints for glass-reinforced
thermosetting plastics (GRP) pipes and fittings
- Test methods for leaktightness and resistance
to damage of flexible and reduced-articulation
joints
EN 12293-1999 塑料管道系统 热水和冷水用热塑性塑料管道和接头 安装组件耐热循环性的试验方法
Plastics piping systems - Thermoplastics pipes
and fittings for hot and cold water - Test method
for the resistance of mounted assemblies to
temperature cycling
EN 12295-1999 塑料管道系统 热水和冷水用热塑性塑料管道和接头 接合处耐压力循环试验方法
Plastics piping systems - Thermoplastics pipes
and associated fittings for hot and cold water
- Test method for resistance of joints to pressure
cycling
EN 12308-1998 液化天然装置和设备 液化天然气管道中所用的法兰接头垫圈设计适配性试验
Installations and equipment for LNG - Suitability
testing of gaskets designed for flanged joints
used on LNG piping
EN 12345-1998 焊接 带图示的有关焊接接头的多语种术语 Welding -
Multilingual terms for welded joints with illustrations
EN 12512-2001 原木结构 试验方法 机械紧固件形成接头的循环试验 Timber
structures - Test methods - Cyclic testing of
joints made with mechanical fasteners
EN 12517-1998 焊缝的无损检验 焊接接头放射线检验 验收等级 Non-destructive
examination of welds - Radiographic examination
of welded joints - Acceptance levels
EN 12560-1-2001 法兰和其接头 指定等级的法兰垫片 第1部分：带或不带垫圈的非金属法兰垫片
Flanges and their joints - Gaskets for Class-designated
flanges - Part 1: Non-metallic flat gaskets
with or without inserts
EN 12560-2-2001 法兰和其接头 指定等级的法兰垫片 第2部分：钢制法兰用螺旋形垫片
Flanges and their joints - Gaskets for Class-designated
flanges - Part 2: Spiral wound gaskets for use
with steel flanges
EN 12560-3-2001 法兰和其接头 指定等级的法兰垫片 第3部分：非金属PTFE封套垫片
Flanges and their joints - Gaskets for Class-designated
flanges - Part 3: Non-metallic PTFE envelope
gaskets
EN 12560-4-2001 法兰和其接头 指定等级的法兰垫片 第4部分：钢法兰用波纹状、平或插榫金属垫片
Flanges and their joints - Gaskets for Class-designated
flanges - Part 4: Corrugated, flat or grooved
metallic and filled metallic gaskets for use
with steel flanges
EN 12560-5-2001 法兰和其接头 指定等级的法兰垫片 第5部分：钢法兰用金属环接合垫片
Flanges and their joints - Gaskets for Class-designated
flanges - Part 5: Metallic ring joint gaskets
for use with steel flanges
EN 12573-4-2000 静态无压焊接热塑料罐 第4部分：法兰接头的设计和计算 Welded
static non-pressurized thermoplastic tanks -
Part 4: Design and calculation of flanged joints
EN 1277-1996 塑料管道系统 地下无压用热塑管道系统 弹性密封环型接头密封性试验方法
Plastics piping systems - Thermoplastics piping
systems for buried non-pressure applications
- Test methods for leaktightness of elastomeric
sealing ring type joints
EN 12797-2000 铜焊 铜焊接头的破坏性试验 Brazing - Destructive
tests of brazed joints
EN 12799-2000 铜焊 铜焊接头的破坏性试验 Brazing - Non-destructive
examination of brazed joints
EN 1281-1-1997+A1-1998 麻醉和呼吸设备 圆锥形接头器 第1部分：锥体和锥套
Anaesthetic and respiratory equipment - Conical
connectors - Part 1: Cones and sockets
EN 1281-2-1995 麻醉和呼吸设备 圆锥形接头 第2部分：螺纹承重连接头 Anaesthetic
and respiratory equipment - Conical connectors
- Part 2: Screw-threaded weight-bearing connectors
(ISO 5356-2:1987 modified)
EN 12814-1-1999+AC-2003 热塑性塑料半成品的焊接接头试验 第1部分：弯曲试验
Testing of welded joints of thermoplastics semi-finished
products - Part 1: Bend test
EN 12814-2-2000 热塑性塑料半成品的焊接接头试验 第2部分：拉伸试验 Testing
of welded joints of thermoplastics semi-finished
products - Part 2: Tensile test
EN 12814-3-2000 热塑性塑料半成品的焊接接头试验 第3部分：拉伸蠕变试验
Testing of welded joints of thermoplastics semi-finished
products - Part 3: Tensile creep test
EN 12814-4-2001 热塑性塑料半成品的焊接接头试验 第4部分：剥落试验 Testing
of welded joints of thermoplastics semi-finished
products - Part 4: Peel test
EN 12814-5-2000 热塑性塑料半成品的焊接接头试验 第5部分：目测 Testing
of welded joints of thermoplastics semi-finished
- Part 5: Macroscopic examination
EN 12814-6-2000 热塑性塑料半成品的焊接接头试验 第6部分：低温拉伸试验
Testing of welded joints of thermoplastics semi-finished
products - Part 6: Low temperature tensile test
EN 12814-7-2002 热塑性塑料半成品的焊接接头试验 第7部分：采用腰形试样的拉伸试验
Testing of welded joints of thermoplastics semi-finished
products - Part 7: Tensile test with waisted
test specimens
EN 12814-8-2001+AC-2003 热塑性塑料半成品的焊接接头试验 第8部分：要求
Testing of welded joints of thermoplastics semi-finished
products - Part 8: Requirements
EN 13090-2000 建筑物中气体管道螺纹接头再密封方法 Means for resealing
threaded joints of gas pipework in buildings
EN 13100-1-1999 热塑性塑料半成品焊接接头的无损检验 第1部分：外观检查
Non destructive testing of welded joints of
thermoplastics semi-finished products - Part
1: Visual examination
EN 1636-5-1997 无压力排水和污水用塑料管道系统 不饱和聚脂树脂(UP) 基玻璃纤维增强热固性塑料(GRP)
第5部分：针对接头 Plastics piping systems for non-pressure
drainage and sewerage - Glass-reinforced thermosetting
plastics (GRP) based on unsaturated polyester
resin (UP) - Part 5: Fitness for purpose of
the joints
EN 1707-1996 注射器、针头和其它医疗器械用有6%鲁尔的锥形接头 锁紧接头 Conical
fittings with a 6 % (Luer) taper for syringes,
needles and certain other medical equipment
- Lock fittings
EN 1708-1-1999 焊接 钢件的焊接接头基础详细资料 第1部分：压力用途部件
Welding - Basic weld joint details in steel
- Part 1: Pressurized components
EN 1708-2-2000 焊接 钢件的焊接接头基础详细资料 第2部分：无内部压力用途部件
Welding - Basic weld joint details in steel
- Part 2: Non internal pressurized components
EN 1712-1997 焊接无损检验 焊接接头超声波检测 验收水平 Non destructive
examination of welds - Ultrasonic examination
of welded joints - Acceptance levels
EN 1714-1997 焊接无损检验 焊接接头超声检验 Non destructive
examination of welds - Ultrasonic examination
of welded joints
EN 1736-2000 制冷系统和热泵 软管元件 振动隔离器和伸缩接头 要求、设计和安装
Refrigerating systems and heat pumps - Flexible
pipe elements, vibration isolators and expansion
joints - Requirements, design and installation
EN 1737-1998 高压多孔混凝土或开放结构轻集料混凝土预制件用钢筋板或框架焊接接头剪切强度的测定
Determination of shear strength of welded joints
of reinforcement mats or cages for prefabricated
components made of autoclaved aerated concrete
or lightweight aggregate concrete with open
structure
EN 1739-1998 高压多孔混凝土或开放结构的轻集料混凝土制预制件之间接头内面力的剪切强度的测定
Determination of shear strength for in-plane
forces of joints between prefabricated components
made of autoclaved aerated concrete or lightweight
aggregate concrete with open structure
EN 1741-1998 高压多孔混凝土或开放结构的轻集料混凝土制预制件之间接头的外面力的剪切强度的测定
Determination of shear strength for out-of-plane
forces of joints between prefabricated components
made of autoclaved aerated concrete or lightweight
aggregate concrete with open structure
EN 175201-804-1999 详细规范：圆形连接器 螺纹接头直径为1.6mm的圆接触件
Detail specification: Circular connectors -
Round contacts, size diameter 1,6 mm, threaded
coupling
EN 1759-3-2003 法兰及其接头 管材、阀门、管件及附件用已命名种类的圆形法兰
第2部分：铜合金法兰 Flanges and their joints - Circular
flanges for pipes, valves, fittings and accessories,
class designated - Part 3: Copper alloy flanges
EN 1759-4-2003 法兰及其接头 管材、阀门、管件及附件用已命名种类的圆形法兰
第4部分：铝合金法兰 Flanges and their joints - Circular
flanges for pipes, valves, fittings and accessories,
class designated - Part 4: Aluminium alloy flanges
EN 1989-2000 热塑性管道系统 埋地无压污水用接头 通过估计密封压力对热塑弹性塑料(TPE)密封接头的长时间密封性能的试
Thermoplastics piping systems - Joints for buried
non-pressure sewerage applications - Test method
for long-term sealing performance of joints
with thermoplastic elastomer (TPE) seals by
estimating the sealing pressure
EN 20594-1-1993+A1-1997+AC-1996 注射器、针头及其他医疗器械为6%（鲁尔）的锥形接头
第1部分：一般要求 Conical fittings with a 6% (Luer)
taper for syringes, needles and certain other
medical equipment; part 1: general requirements
(ISO 594-1:1986)
EN 25817-1992 钢弧焊接头 缺点质量分级指南 Arc-welded joints
in steel; guidance on quality levels for imperfections
(ISO 5817:1992)
EN 25821-1991 电阻点焊电极帽接头 Resistance spot welding,
electrode caps (ISO 5821:1979)
EN 2591-217-2002 航空航天系列 光电连接元件 试验方法 第217部分：.在规定接线接片和在线接头电流内的电压降
Aerospace series - Elements of electrical and
optical connection; Test methods - Part 217:
Voltage drop under specified current for terminal
lugs and in-line splices
EN 2591-218-2002 航空航天系列 光电连接元件 试验方法 第２１８部分：温度和电流循环变化使接线按片和在线接头引起老化
Aerospace series - Elements of electrical and
optical connection; Test methods - Part 218:
Ageing of terminal lugs and in-line splices
by temperature and current cycling
EN 2591-219-2002 航空航天系列 光电连接元件 试验方法 第２１９部分：绝缘接线按片和在线接头电压强度
Aerospace series - Elements of electrical and
optical connection; Test methods - Part 219:
Voltage strength for insulated terminal lugs
and in-line splices
EN 26891-1991 木材结构 机械紧固件接头 强度和变形特性测定的一般原则 Timber
structures - Joints made with mechanical fasteners
- General principles for the determination of
strength and deformation characteristics (ISO
6891:1983)
EN 26922-1993 粘合剂 对接头抗拉强度的测定 Adhesives - Determination
of tensile strength of butt joints (ISO 6922:1987)
EN 28430-1-1992 电阻点焊 电极夹具 第1部分：锥形接头锥度1:10 Resistance
spot welding- Electrode holders- Part 1: Taper
fixing 1:10 (ISO 8430-1:1988)
EN 28970-1991 木材结构 机械紧固件接头的试验 对木材密度要求 Timber
structures - Testing of joints made with mechanical
fasteners - Requirements for wood density (ISO
8970:1989)
EN 295-1-1991+AA1-1996+A2-1996+A3-1999 排水管和下水道用陶瓷粘土管和管配件及管接头
第1部分：要求 Vitrified clay pipes and fittings and
pipe joints for drains and sewers; part 1: requirements
EN 295-2-1991+A1-1999 排水管和下水道用陶瓷粘土管和管配件及管接头
第2部分：质量控制和取样 Vitrified clay pipes and fittings
and pipe joints for drains and sewers; part
2: quality control and sampling
EN 295-3-1991+A1-1998 排水管和下水道用陶瓷粘土管和管配件及管接头
第3部分：试验方法 Vitrified clay pipes and fittings
and pipe joints for drains and sewers; part
3: test methods
EN 295-4-1995+AC-1998 排水管和下水道用陶瓷粘土管和管配件及管接头
第4部分：专用配件、管接头和配套附件的要求 Vitrified clay pipes and
fittings and pipe joints for drains and sewers
- Part 4: Requirements for special fittings,
adaptors and compatible accessories
EN 295-5-1994+A1-1999 排水管和下水道用陶瓷粘土管和管配件及管接头
第5部分：带孔的陶瓷粘土管及配件的要求 Vitrified clay pipes and
fittings and pipe joints for drains and sewers
- Part 5: Requirements for perforated virtrified
clay pipes and fittings
EN 295-6-1995 排水管和下水道用陶瓷粘土管和管配件及管接头 第6部分：陶瓷粘土检修孔的要求
Vitrified clay pipes and fittings and pipe joints
for drains and sewers - Part 6: Requirements
for vitrified clay manholes
EN 295-7-1995 排水管和下水道用陶瓷粘土管和管配件及管接头 第7部分：管托起用陶瓷粘土管和接头的要求
Vitrified clay pipes and fittings and pipe joints
for drains and sewers - Part 7: Requirements
for vitrified clay pipes and joints for pipe
jacking
EN 30042-1994 铝和铝焊合金弧焊接头 缺陷质量分级指南 Arc-welded
joints in aluminium and its weldable alloys
- Guidance on quality levels for imperfections
(ISO 10042:1992)
EN 3082-2001+AC-2003 航空航天系列 钛合金管连接件8°30′修理用焊接端的舱壁管接头
Aerospace series - Pipe coupling 8°30′in titanium
alloy - Unions, bulkhead welded end, for repair
EN 3083-2001+AC-2003 航空航天系列 钛合金管连接件8°30′修理用长焊接端舱壁管接头
Aerospace series - Pipe coupling 8?0 in titanium
alloy - Unions, bulkhead, long welded end, for
repair
EN 3084-2001+AC-2003 航空航天系列 钛合金管连接件8°30′修理用焊接端螺纹管接头
Aerospace series - Pipe coupling 8°30′in titanium
alloy - Unions, welded end threaded for repair
EN 3244-2001 航空航天系列 钛合金管连接件8°30′双端口管接头 Aerospace
series - Pipe coupling 8?30 in titanium alloy
- Unions, double ended
EN 3245-2001 航空航天系列 钛合金管连接件8°30′ 异径管接头 Aerospace
series - Pipe coupling 8?30 in titanium alloy
- Unions, reducer
EN 3246-2001 航空航天系列 钛合金管连接件8°30′舱壁管接头 Aerospace
series - Pipe coupling 8?30 in titanium alloy
- Unions, bulkhead
EN 3247-2001 航空航天系列 钛合金管连接件8°30′舱壁焊接端管接头 Aerospace
series - Pipe coupling 8?30 in titanium alloy
- Unions, bulkhead welded end
EN 3248-2001 航空航天系列 钛合金管连接件8°30′带锁异径管端管接头 Aerospace
series - Pipe coupling 8°30′in titanium alloy
- Adaptors, reduced pipe end, with lockring
EN 3273-2001 航空航天系列 钛合金管连接件8°30′ 带动态梁密封端的弯管、十字管和三通接头
几何结构 Aerospace series - Pipe coupling 8?30 -
Dynamic beam seal end for elbows, tees and crosses;
Geometric configuration
EN 3566-2001+AC-2003 航空航天系列 钛合金管连接件8°30′具有锁环的管接头
Aerospace series - Pipe coupling 8?0 in titanium
alloy - Adaptors with lockring
EN 3690-2001+AC-2003 航空航天系列 钛合金管连接8°30′长舱壁管接头
Aerospace series - Pipe coupling 8?0 in titanium
alloy - Unions, bulkhead, long
EN 3691-2001+AC-2003 航空航天系列 钛合金管连接8°30′长焊舱壁管接头
Aerospace series - Pipe coupling 8?0 in titanium
alloy - Unions, bulkhead, long welded
EN 4026-2001 航空航天系列 钛合金管连接 8°30′三通接头 Aerospace
series - Pipe coupling 8?0 in titanium alloy
- Tees
EN 4186-2001 航空航天系列 钛合金管连接8°30′四通管接头 Aerospace
series - Pipe coupling 8 Degree 30′in titanium
alloy - Unions, cross
EN 4233-2001 航空航天系列 钛合金管连接 8°30′ 焊接螺纹管接头 Aerospace
series - Pipe coupling 8 Degree 30′in titanium
alloy - Unions, welded, threaded
EN 4552-2003 航空航天系列 耐热钢37度球形联管节 焊接直接头 英制系列 Aerospace
series - Pipe coupling 37? spherical, in heat
resisting steel - Straight nipples, welded end;
Inch series
EN 4553-2003 航空航天系列 耐热钢37度球形联管节 焊接90度弯接头 英制系列
Aerospace series - Pipe coupling 37? spherical,
in heat resisting steel - Elbow 90?nipples,
welded end; Inch series
EN 4554-2003 航空航天系列 耐热钢37度球形联管节 直螺纹管接头 英制系列
Aerospace series - Pipe coupling 37? spherical,
in heat resisting steel - Straight unions, threaded;
Inch series
EN 4557-2003 航空航天系列 耐热钢37度球形联管节 焊末端T形接头 英制系列
Aerospace series - Pipe coupling 37? spherical,
in heat resisting steel - Tees nipples, welded
end; Inch series
EN 4563-2003 航空航天系列 耐热钢焊接联管节 T形接头 英制系列 Aerospace
series - Pipe coupling, welded, in heat resisting
steel - Tees; Inch series
EN 489-2003 热水分配管道 地下热水网用预隔热包覆的管道系统 成套钢铁管道设备的接头组件、聚氨酯热绝缘和聚乙烯外
District heating pipes - Preinsulated bonded
pipe systems for directly buried hot water networks
- Joint assembly for steel service pipes, polyurethane
thermal insulation and outer casing of polyethylene
EN 512-1994+A1-2001 纤维水泥制品 压力管道和接头 Fibre-cement
products - Pressure pipes and joints
EN 514-2000 门窗建造用未增塑聚氯乙烯型材 焊接弯头和T型接头强度的测定 Unplasticized
polyvinylchloride (PVC-U) profiles for the fabrication
of windows and doors - Determination of the
strength of welded corners and T joints
EN 545-2002 给水管道用球墨铸铁管、配件、附件及其接头 要求和试验方法 Ductile
iron pipes, fittings, accessories and their
joints for water pipelines - Requirements and
test methods
EN 598-1994 污水工程用球墨铸铁管、配件、附件和其它接头 要求和试验方法 Ductile
iron pipes, fittings, accessories and their
joints for sewerage application - Requirements
and test methods
EN 60239-1997 电弧炉用带螺纹座的圆柱形机制石墨电极和接头的标称尺寸 Nominal
dimensions of cylindrical machined graphite
electrodes with threaded sockets and nipples
for use in electric arc furnaces (IEC 60239:1997)
EN 60512-11-13-2002 电子设备用连接器 试验和测量 第11-13部分：气候试验 试验11n:气密
无焊包封接头 Connectors for electronic equipment -
Tests and measurements - Part 11-13: Climatic
tests; Test 11n: Gas tightness, solderless wrapped
connections (IEC 60512-11-13:2002)
EN 60874-17-1997 光纤和电缆的接头 第１７部分：纤维光学接头的部分规范 F-05型(磨擦锁定)
Connectors for optical fibres and cables - Part
17: Sectional specification for fibre optic
connector - Type F-05 (friction lock) (IEC 60874-17:1995
+ Corrigendum 1996)
EN 61073-1-2000 光纤光缆机械式接头和熔接式接头保护盒 第1部分：通用规范
Mechanical splices and fusion splice protectors
for optical fibres and cables - Part 1: Generic
specification (IEC 61073-1:1999)
EN 639-1994 包括接头和配件的混凝土压力管的通用要求 Common requirements
for concrete pressure pipes including joints
and fittings
EN 640-1994 包括接头和配件的钢筋混凝土压力管和分布式钢筋混凝土压力管(非圆柱型)
Reinforced concrete pressure pipes and distributed
reinforcement concrete pressure pipes (non-cylinder
type), including joints and fittings
EN 641-1994 包括接头和配件的圆柱型钢筋混凝土压力管 Reinforced concrete
pressure pipes, cylinder type, including joints
and fittings
EN 642-1994 包括接头、配件的圆柱型和非圆柱型预应力混凝土压力管和预应力钢管的特殊要求
Prestressed concrete pressure pipes, cylinder
and non-cylinder type, including joints, fittings
and specific requirement for prestressing steel
for pipes
EN 74-1988 用于由钢管制造的工作脚手架和工作架的管接头、活动套管和底板 要求和试验程序
Couplers, loose spigots and base-plates for
use in working scaffolds and falsework made
of steel tubes; Requirements and test procedures
EN 751-1-1996 接触第1、2、3家庭用燃气和热水的金属螺纹接头的密封材料 第1部分：气密连接
Sealing materials for metallic threaded joints
in contact with 1st, 2nd and 3rd family gases
and hot water - Part 1: Anaerobic jointing compounds
EN 751-2-1996 接触第1、2、3家庭用燃气和热水的金属螺纹接头的密封材料 第2部分：非硬化连接
Sealing materials for metallic threaded joints
in contact with 1st, 2nd and 3rd family gases
and hot water - Part 2: Non-hardening jointing
compounds
EN 751-3-1996+AC-1997 接触第1、2、3家庭用燃气和热水的金属螺纹接头的密封材料
第3部分：非烧结过的聚四氟乙烯密封带 Sealing materials for metallic
threaded joints in contact with 1st, 2nd and
3rd family gases and hot water - Part 3: Unsintered
PTFE tapes
EN 804-1994 塑料管道系统 压力管道溶焊接头的喷射铸造插接部件 瞬时内部液压阻力的试验方法
Plastics piping systems - Injection-moulded
socket fittings for solvent-cemented joints
for pressure piping - Test method for resistance
to a short-term internal hydrostatic pressure
EN 850-1996+A1-2000+AC-1998 可移动气瓶 医用枢接轭状阀门出口接头
Transportable gas cylinders - Pin-index, yoke-type
valve outlet connections for medical use
EN 876-1995 金属材料焊接的破坏试验 熔焊接头中焊接金属的纵向拉伸试验 Destructive
tests on welds in metallic materials - Longitudinal
tensile test on weld metal in fusion welded
joints
EN 877-1999 建筑物排水用铸铁管和配件及其接头和附件 要求、试验方法和质量保证
Cast iron pipes and fittings, their joints and
accessories for the evacuation of water from
buildings - Requirements, test methods and quality
assurance
EN 911-1995 塑料管道系统 热塑塑料压力管道用的弹性密封环型接头和机械接头 外部液压条件下防漏密封试验方法
Plastics piping systems - Elastomeric sealing
ring type joints and mechanical joints for thermoplastics
pressure piping - Test method for leaktightness
under external hydrostatic pressure
EN 969-1995+A1-1998 煤气管道用球墨铸铁管、配件、附件及其接头 要求和试验方法
Ductile iron pipes, fittings, accessories and
their joints for gas pipelines - Requirements
and test methods
EN ISO 10321-1996 土工布 宽条样法对接头/接缝的拉身试验 Geotextiles
- Tensile test for joints/seams by wide-width
method (ISO 10321:1992)
EN ISO 10692-1-2001 气瓶 微电子工业用气瓶阀接头 第1部分：出口接头
Gas cylinders - Gas cylinder valve connections
for use in the microelectronics industry - Part
1: Outlet connections (ISO 10692-1:2001)
EN ISO 10692-2-2001 气瓶 微电子工业用气瓶阀接头 第2部分：气瓶阀接头的规范和定型试验
Gas cylinders - Gas cylinder valve connections
for use in microelectronic industry - Part 2:
Specification and type testing for valve to
cylinder connections (ISO 10692-2:2001)
EN ISO 11144-1996 牙科设备 供水及排水管接头 Dental equipment
- Connections for supply and waste lines (ISO
11144:1995)
EN ISO 1120-2002 输送带 机械接头的强度测定 静态试验法 Conveyor
belts - Determination of strength of mechanical
fastenings - Static test method (ISO 1120:2002)
EN ISO 11446-2002 乘用车和具有12伏电压系统的轻型商用车 牵引车和挂车之间的13极连接器的尺寸和接头的分布
Passenger cars and light commercial vehicles
with 12 V systems - 13-pole connectors between
towing vehicles and trailers - Dimensions and
contact allocation (ISO 11446:1995 and Amd.
1:1997) / Note: To be replaced by prEN ISO 11446
(2003-10).
EN ISO 13919-1-1996 焊接 电子束和激光焊接头 缺陷的质量分级指南 第1部分：钢
Welding - Electrons and laser-beam welded joints
- Guidance on quality levels for imperfections
- Part 1: Steel (ISO 13919-1:1996)
EN ISO 13919-2-2001 焊接 电子束和激光焊接头 缺陷的质量分级指南 第2部分：铝及其可焊合金
Welding - Electron and laser beam welded joints
- Guidance on quality levels for imperfections
- Part 2: Aluminium and its weldable alloys
(ISO 13919-2:2001)
EN ISO 15614-8-2002 金属焊接工艺的规范和验收 焊接工艺试验 第8部分：管对管板接头焊接
Specification and qualification of welding procedures
for metallic materials - Welding procedure test
- Part 8: Welding of tubes to tube-plate joints
(ISO 15614-8:2002)
EN ISO 15785-2002 技术制图 粘接接头、折叠接头和压接头的符号表示与标示
Technical drawings - Symbolic presentation and
indication of adhesive, folded and pressed joints
(ISO 15785:2002)
EN ISO 5183-1-2000 电阻焊设备 外锥度1:10电极接头 第1部分：锥度1:10圆锥形接头
Resistance welding equipment - Electrode adaptors,
male taper 1:10 - Part 1: Conical fixing, taper
1:10 (ISO 5183-1:1998)
EN ISO 5183-2-2001 电阻点焊设备 外锥度1:10电极接头 第2部分：端推力电极用平行柄接头
Resistance spot welding - Electrode adaptors,
male taper 1:10 - Part 2: Parallel shank fixing
for end-thrust electrodes (ISO 5183-2:2000)
EN ISO 5620-1-1996 造船及海上结构物 饮水舱的注水接头 第1部分：一般要求
Shipbuilding and marine structures - Filling
connection for drinking water tanks - Part 1:
General requirements (ISO 5620-1:1992)
EN ISO 5620-2-1996 造船及海上结构物 饮水舱的注水接头 第2部分：零件
Shipbuilding and marine structures - Filling
connection for drinking water tanks - Part 2:
Components (ISO 5620-2:1992)
EN ISO 5828-2001 电阻焊设备 连接水冷接头的二次连接电缆 尺寸及特性 Resistance
welding equipment - Secondary connecting cables
with terminals connected to water-cooled lugs
- Dimensions and characteristics (ISO 5828:2001)
EN ISO 8092-1-1998 道路车辆 车载电气线束的连接 第1部分：单极连接接头 尺寸和特殊要求
Road vehicles - Connections for on-board electrical
wiring harnesses - Part 1: Tabs for single-pole
connections - Dimensions and specific requirements
(ISO 8092-1:1996)
EN ISO 8092-3-1999 道路车辆 车载电气线束的连接 第3部分：多极连接接头 尺寸和特殊要求
Road vehicles - Connections for on-board electrical
wiring harnesses - Part 3: Tabs for multi-pole
connections - Dimensions and specific requirements
(ISO 8092-3:1996)
EN ISO 8434-1-1997 用于流体传动和一般用途的金属管接头 第1部分：24度缩式管接头
Metallic tube connections for fluid power and
general use - Part 1: 24 degrees compression
fittings (ISO 8434-1:1994)
EN ISO 8434-4-2000 用于流体传动和一般用途的金属管接头 第4部分：带O形圈焊接接头体的24度锥形管接头
Metallic tube connections for fluid power and
general use - Part 4: 24?degrees cone connectors
with O-ring weld-on nipples (ISO 8434-4:1995)
EN ISO 9692-2-1998 焊接和相关工艺 接头的制备 第2部分：钢的埋弧焊
Welding and allied processes - Joint preparation
- Part 2: Submerged arc welding of steels (ISO
9692-2:1998)
EN ISO 9692-3-2001 焊接和相关工艺 接头制备的建议 第3部分：铝及铝合金的金属焊条惰性气体保护焊和钨焊条惰性气体保护焊
Welding and allied processes - Recommendations
for joint preparation - Part 3: Metal inert
gas welding and tungsten inert gas welding of
aluminium and its alloys (ISO 9692-3:2000)
EN ISO 9692-4-2003 焊接和相关工艺 接头制备的建议 第4部分：复合钢
Welding and allied processes - Recommendations
for joint preparation - Part 4: Clad steels
(ISO 9692-4:2003)
prEN 1016-1993 塑料管道系统 非可塑聚氯乙烯一端受载的双孔接头 弯曲和内部压力时的密封性和强度试验方法
Plastics piping systems; unplasticized poly(vinyl
chloride) (PVC-U) end-load bearing double socket
joints; test method for leaktightness and strength
while subjected to bending and internal pressure
prEN 10311-1999 传送人类消耗的含水液体（包括水）的钢管和接头间的连接件
Joints for the connection of steel tubes and
fittings for the conveyance of aqueous liquids
including water for human consumption
prEN 10329-2002 岸上和海上管路钢管及配件 外表安装接头涂层 Steel
tubes and fittings for onshore and offshore
pipelines - External field joint coatings
prEN 1115-2-1997 压力下地下排水和排污装置用塑料管道系统 基于非饱和聚酯树脂的玻璃增强热固性塑料（GRP）
第2部分：具挠 Plastics piping systems for underground
drainage and sewerage under pressure - Glass-reinforced
thermosetting plastics (GRP) based on unsaturated
polyester resin (UP) - Part 2: Pipes with flexible,
reduced articulation or rigid joints
prEN 12560-6-2003 法兰和其接头 指定等级的法兰垫片 第６部分：钢法兰用有锯齿的金属垫片
Flanges and their joints - Gaskets for class-designated
flanges - Part 6: Covered serrated metal gaskets
for uses with steel flanges
prEN 12560-7-2001 法兰和其接头 指定等级的法兰垫片 第７部分：钢法兰用有金属套的垫片
Flanges and their joints - Dimensions of gaskets
for Class designated flanges - Part 7: Covered
metal jacketed gaskets for use with steel flanges
prEN 12927-1-1997 索道客运的安全要求 钢索 第1部分：钢索及其端部接头的选择准则
Safety requirements for passenger transport
by rope - Ropes - Part 1: Selection criteria
for ropes and their end fixings
prEN 12927-4-2001 索道客运的安全要求 钢索 第4部分：端部接头 Safety
requirements for passenger transportation by
rope - Ropes - Part 4: End fixing
prEN 13100-2-2002 热塑性塑料半成品焊接接头的无损检验 第2部分：X射线检查法
Non destructive testing of welded joints of
thermoplastics semi-finished products - Part
2: X-ray radiographic testing
prEN 13100-3-2002 热塑性塑料半成品焊接接头的无损检验 第3部分：超声检测
Non destructive testing of welded joints of
thermoplastics semi-finished products - Part
3: Ultrasonic testing
prEN 1336-1993 塑料管道系统 热塑性压力管道用终端承载和无承开组件和接头
内部水压力下长期密封性试验方法 Plastics piping systems; end-load-bearing
and non-end-load-bearing assemblies and joints
for thermoplastics pressure piping; test method
for long-term leaktightness under internal water
pressure
prEN 13476-1-2002 非压力地下排水和污水热塑性塑料管道系统 聚氯乙烯（PVC-U）、聚丙烯（PP）)和聚已烯（PE）的结构墙管道系
Plastics piping systems for non-pressure underground
drainage and sewerage - Structured-wall piping
systems of unplasticized poly(vinyl chloride)
(PVC-U), polypropylene (PP) and polyethylene
(PE) - Part 1: Specifications for pipes, fittings
and the syste
prEN 13763-7-2003 民用炸药 雷管和继电器 第7部分：引线、冲击管、接头、卷边和封闭机械强度的测定方法
Explosives for civil uses - Detonators and relays
- Part 7: Determination of the mechanical strength
of leading wires, shock tubes, connections,
crimps and closures
prEN 14257-2001 粘合剂 木材粘合剂 高温下搭接头的拉力强度的测定 Adhesives
- Wood adhesives - Determination of tensile
strength of lap joints at elevated temperature
(WATT91)
prEN 14258-2001 粘合剂 在特殊温度条件下接头长时和短时期暴露的机械性能
Adhesives - Mechanical behaviour of joints subjected
to short and long terms exposure at specified
conditions of temperature
prEN 14364-2002 有或无压排水和排污塑料管线系统 玻璃纤维增强的未饱和的聚酯树脂基热固塑料管
塑料管管件及接头规范 Plastics piping systems for drainage
and sewerage with or without pressure - Glass-reinforced
thermosetting plastics (GRP) based on unsaturated
polyester resin (UP) - Specifications for pipes,
fittings and joints
prEN 1636-2-1996 无压力排水道和污水用塑料管道系统 不饱和聚脂树脂(UP)
基玻璃纤维增强热固性塑料(GRP) 第2部分：带有挠 Plastics piping systems
for non-pressure drainage and sewerage - Glass-reinforced
thermosetting plastics (GRP) based on unsaturated
polyester resin (UP) - Part 2: Pipes with flexible,
reduced articulation or rigid joints
prEN 1759-1-2000 法兰及其接头 管材、阀门、管件及附件用已命名种类的圆形法兰
第1部分：钢法兰NPS1/2到24 Flanges and their joints -
Circular flanges for pipes, valves, fittings
and accessories, class designated - Part 1:
Steel flanges, NPS 1/2 to 24
prEN 1763-2-2000 供气相丙烷和丁烷使用的挠性软管、管道及组装件 第2部分：对管咀接头及组装件的要求
Flexible hose, tubing and assemblies for use
with propane and butane in the vapour phase
- Part 2: Requirements for nozzles, couplings
and assemblies
prEN 1796-2-1995 有或无压力供水用塑料管道系统 非饱和性聚脂树脂基玻璃增强热固性塑料
第2部分：带挠性、缩口活节或刚性 Plastics piping systems for
water supply with or without pressure - Glass-reinforced
thermosetting plastics (GRP) based on polyester
resin (UP) - Part 2: Pipes with flexible, reduced
articulation or rigid joints
prEN 185000-1992 通用规范：光学接头和光缆用光纤接头硬件 Generic
specification: fibre optic splice hardware for
optical splices and cables
prEN 2591-220-2000 航空航天系列 光电连接元件 试验方法 第２２０部分：电流和温度循环变化使接触端／导线接头老化
Aerospace series - Elements of electrical and
optical connection; Test methods - Part 220:
Contact/conductor joint ageing by current and
temperature cycling
prEN 2608-1999 航空航天系列 锁环螺纹式8°0′管接头的安装和拆卸要求 Aerospace
series - Installation and removal requirements
for 8?0 adaptoros, threaded with lockring
prEN 295-10-2001 排水管和下水道用陶瓷粘土管和管配件及管接头 第10部分：强制要求
Vitrified clay pipes and fittings and pipe joints
for drains and sewers - Part 10: Mandated requirements
prEN 3079-1999 航空航天系列 管连接件8°30′ 直到 28000 kPa
异形接头米制系列 技术规范 Aerospace series - Pipe coupling
8?30 up to 28000 kPa - Adaptors - Metric series
- Technical specifiations
prEN 60603-7-4-2003 电气设备接头 第7-4部分：用于数据传输频率高达
250 MHz (第 6类, 未屏蔽)的8道活动和固定接头的技术规范 IEC 60603-7-4,
Ed. 1.0: Connectors for electronic equipment
- Part 7-4: Detail specification for 8-way,
unshielded, free and fixed connectors, for data
transmissions with frequencies up to 250 MHz
prEN 61076-2-101-2003 电子设备用连接器 第2-101部分：低压、开关和控制装置用带有M8和M12螺旋接头以及弹簧锁的圆形连接器的空白
Connectors for electronic equipment - Part 2-101:
Circular connectors M8 with screw- or snap-locking,
M12 with screw-locking for low voltage applications
prEN 630-1992 铝及其焊接合金中的电弧焊接头 缺陷质量级别指南 Arc-welded
joints in aluminium and its weldable alloys;
guidance on quality levels for imperfections
(ISO/DIS 10042 modified)
prEN 762-1995 塑料管道和导管系统 热塑系统用弹性密封接头 密封环保持力和损坏的试验方法
Plastics piping and ducting systems - Joints
with elastomeric seals for thermoplastic systems
- Test method for retention of, and damage to,
sealing rings
prEN ISO 14617-3-2002 图表用图形符号 第3部分：接头及相关装置 Graphical
symbols for diagrams - Part 3: Connections and
related devices (ISO/FDIS 14617-3:2002)
prEN ISO 15236-4-2000 钢芯传输带 第4部分：硫化橡胶传输带接头、设计、尺寸、要求、标记
Steel cord conveyor belts - Part 4: Vulcanized
belt joints; Design, dimensions, requirements,
marking (ISO/DIS 15236-4:2000)
prEN ISO 15875-3-2002 冷热水塑料管道系统 交联聚乙稀（ PE -
X ） 第3部分：接头 Plastics piping systems for hot
and cold water installations - Crosslinked polyethylene
(PE-X) - Part 3: Fittings (ISO/FDIS 15875-3:2002)
prEN ISO 15876-3-2002 冷热水塑料管道系统 聚丁稀（ PB ） 第3部分：接头
Plastics piping systems for hot and cold water
installations - Polybutylen (PB) - Part 3: Fittings
(ISO/FDIS 15876-3:2002)
prEN ISO 15877-3-2002 冷热水用塑料管道系统 氯化聚氯乙烯（PVC-C）第3部分：接头
Plastics piping systems for hot and cold water
installations - Chlorinated poly(vinyl chloride)
(PVC-C) - Part 3: Fittings (ISO/FDIS 15877-3:2002)
prEN ISO 9018-2003 金属材料焊缝的破坏性试验 十字形与重叠 形接头的拉力试验
Destructive tests on welds in metallic materials
- Tensile test on cruciform and lapped joints
(ISO/FDIS 9018:2003)
prEN ISO 9692-1-2003 焊接和相关工艺 接头制备的推荐工艺 第1部分：钢的人工电弧焊、气体保护金属电弧焊、气焊和束焊
Welding and allied processes - Recommendations
for joint preparation - Part 1: Manual metal-arc
welding, gas-shielded metal-arc welding, gas
welding, TIG welding and beam welding of steels
(ISO/FDIS 9692-1:2003)
中国接头标准(GB joint standards)
--------------------------------------------------------------------------------
编号 中文名称 英文名称
DL/T 542-1994(2005) 钢熔化焊T形接头角焊缝超声波检验方法和质量分级
()
DL/T 820-2002 管道焊接接头超声波检验技术规程 ()
DL/T 821-2002 钢制承压管道对接焊接接头射线检验技术规范 ()
GB/T 10752-2005 船用钢管对焊接头 Marine steel butt-welding
fittings
GB/T 11265-1989 轻轨用接头夹板 Fish plates for light
rails
GB/T 11363-2008 钎焊接头强度试验办法 Test method of the
strength for brazed and soldered joint
GB/T 11618.1-2008 铜管接头 第1部分:钎焊式管件 ()
GB/T 11618.2-2008 铜管接头.第2部分:卡压式管件 Pipe fittings
of copper and copper alloys.Part 2:Fittings
of press type
GB/T 12465-2007 管路补偿接头 Piping compensatory couplings
GB/T 12605-2008 无损检测.金属管道熔化焊环向对接接头射线照相检测方法 Non-destructive
testing.Test methods for radiographic testing
of circumferential fusion-welded butt joints
in metallic pipes and tubes
GB/T 12736-2009 输送带 机械接头强度的测定 静态试验方法 ()
GB/T 14137-1993 光纤机械式固定接头插入损耗测试方法 Optical fiber
mechanical-type splice insertion loss test
GB/T 14149-1993 实验室玻璃仪器 互换球形磨砂接头 Laboratory
glassware--Interchangeable spherial ground joints
GB/T 14171-1993 气制动管路螺纹孔和管接头外螺纹 Motor vehicles--Pneumatic
braking systems--Tapped holes and male fittings
GB/T 14514.1-1993 气动管接头试验方法 Pneumatic fluid
power. Tube fittings. Test methods
GB/T 15830-2008 无损检测.钢制管道环向焊缝对接接头超声检测方法 Non-destructive
testing.Practice for ultrasonic testing of circumferential
butt welds in steel pipes and tubes
GB/T 16529-1996 光纤光缆接头 第1部分;总规范 构件和配件 Splices
for optical fibres and cables. Part 1: Generic
specification--Hardware and accessories
GB/T 16529.2-1997 光纤光缆接头 第2部分;分规范 光纤光缆接头盒和集纤盘
Splices for optical fibres and cables. Part
2: Sectional specification. Splice organizers
and closures for optical fibres and cables
GB/T 16529.3-1997 光纤光缆接头 第3部分;分规范 光纤光缆熔接式接头
Splices for optical fibres and cables. Part
3: Sectional specification. Fusion splices for
optical fibres and cables
GB/T 16529.4-1997 光纤光缆接头 第4部分;分规范 光纤光缆机械式接头
Splices for optical fibres and cables. Part
4: Sectional specification. Mechanical splices
for optical fibres and cables
GB/T 16693-1996 软管快速接头 Quick hose's connection
GB/T 16957-1997 复合钢板焊接接头力学性能试验方法 Mechanical
tests on welded joints in clad plates
GB/T 16989-1997 土工布 接头/接缝宽条拉伸试验方法 ()
GB/T 18615-2002 波纹金属软管用非合金钢和不锈钢接头 Non-alloyed
and stainless steel fittings for corrugated
flexible metallic hoses
GB/T 19418-2003 钢的弧焊接头 缺陷质量分级指南 Arc-welded joints
in steel-Guidance on quality levels for imperfections
GB/T 19471.1-2004 塑料管道系统 硬聚氯乙烯(PVC-U)管材弹性密封圈式承口接头
偏角密封试验方法 Plastics piping systems-Elastomeric-sealing-ring-type
socket joints for use with unplasticized poly(vinyl
chloride)(PVC-U)pipes-Test method for leaktighness
under internal pressure and angular deflection
GB/T 19471.2-2004 塑料管道系统 硬聚氯乙烯(PVC-U)管材弹性密封圈式承口接头
负压密封试验方法 Plastics piping systems-Elastomeric-sealing-ring-type
socket joints of unplasticized poly(vinyl chloride)(PVC-U)for
use with PVC-U pipes-Test method for leaktightness
under negative pressure
GB/T 1962.1-2001 注射器、注射针及其他医疗器械6%(鲁尔)圆锥接头 第1部分;通用要求
The conical fittings with a6%(Luer)taper for
syringes,needles and certain other medical equipment
Part 1:General requirement
GB/T 1962.2-2001 注射器、注射针及其他医疗器械6%(鲁尔)圆锥接头 第2部分;锁定接头
Conical fittings with a 6%(Luer)taper for syringes,needles
and certain other medical equipment Part 2:
Lock fittings
GB/T 19674.1-2005 液压管接头用螺纹油口和柱端 螺纹油口 Connections
for general use and fluid power Ports and stud
ends with thread-Threaded port
GB/T 19674.2-2005 液压管接头用螺纹油口和柱端 填料密封柱端(A型和E型)
Connections for general use and fluid power
Ports and stud ends with thread.Stud ends with
elastomeric sealing(A type and type E)
GB/T 19674.3-2005 液压管接头用螺纹油口和柱端 金属对金属密封柱端(B型)
Connections for general use and fluid power-Ports
and stud ends with thread-Stud ends with metal-to-metal
sealing(type B)
GB/T 19810-2005 聚乙烯(PE)管材和管件 热熔对接接头 拉伸强度和破坏形式的测定
Polyethylene(PE)pipe and fittings.Determination
of the tensile strength and failure mode of
test pieces from a butt-fused joint
GB/T 2031-1994 船用消防接头 Marine fire-fighting coupeigs
GB/T 21297-2007 实验室玻璃仪器 互换锥形磨砂接头 Laboratory
glassware-Interchangeable conical ground joint
GB/T 21359-2008 食品和供水工业用不锈钢螺纹接头 Stainless steel
tube threaded couplings for the food and water
industry
GB/T 21400.2-2008 绞盘式喷灌机.第2部分:软管和接头.试验方法 Traveller
irrigation machines.Part 2:Softwall hose and
couplings.Test methods
GB/T 21410-2008 石油天然气工业.井下工具.锁定心轴和定位接头 Petroleum
and natural gas industries.Downhole equipment.Lock
mandrels and landing nipples
GB/T 22076-2008 气动圆柱形快换接头 插头连接尺寸、技术要求、应用指南和试验
Pneumatic fluid power. Cylindrical quick-action
couplings. Plug connecting dimensions, specifications,
application guidelines and testing
GB/T 22085.1-2008 电子束及激光焊接接头.缺欠质量分级指南.第1部分:钢
Electron and laser beam welded joints-Guidance
on quality levels for imperfections-Part 1:Steel
GB/T 22085.2-2008 电子束及激光焊接接头.缺欠质量分级指南.第2部分:铝及铝合金
Electron and laser beam welded joints-Guidance
on quality levels for imperfection-Part 2:Aluminium
and its weldable alloys
GB/T 22087-2008 铝及铝合金的弧焊接头.缺欠质量分级指南 Arc-welded
joints in aluminium and its alloys.Guidance
on quality levels for imperfection
GB/T 23682-2009 制冷系统和热泵 软管件、隔震管和膨胀接头 要求、设计与安装
()
GB/T 2649-1989 焊接接头机械性能试验取样方法 Methods of sampling
for mechanical properties tests of welded joint
GB/T 2650-2008 焊接接头冲击试验方法 Impact test methods
on welded joints
GB/T 2651-2008 焊接接头拉伸试验方法 Tensile test method
on welded joints
GB/T 2653-2008 焊接接头弯曲试验方法 Bend test methods
on welded joints
GB/T 2654-2008 焊接接头硬度试验方法 Hardness test methods
on welded joints
GB/T 3323-2005 金属熔化焊焊接接头射线照相 Radiographic examination
of fusion welded joints in metallic materials
GB/T 3733-2008 卡套式端直通管接头 24°cone connectors.Straight
thread
GB/T 3734-2008 卡套式锥螺纹直通管接头 24°cone connectors.Male
GB/T 3735-2008 卡套式端直通长管接头 24° cone connectors.
Straight thread long
GB/T 3736-2008 卡套式锥螺纹长管接头 24° cone connectors.
Male long
GB/T 3737-2008 卡套式直通管接头 24°cone connectors.Union
GB/T 3738-2008 卡套式可调向端弯通管接头 24° cone connectors.
Straight thread elbow
GB/T 3739-2008 卡套式锥螺纹弯通管接头 24°cone connectors.Male
elbow
GB/T 3740-2008 卡套式弯通管接头 24°cone connectors.Union
elbow
GB/T 3741-2008 卡套式可调向端三通管接头 24°cone connectors.Straight
thread tee
GB/T 3742-2008 卡套式锥螺纹三通管接头 24°cone connectors.Male
tee
GB/T 3743-2008 卡套式可调向端弯通三通管接头 24° cone connectors.Straight
thread run tee
GB/T 3744-2008 卡套式锥螺纹弯通三通管接头 24° cone connectors.Male
run tee
GB/T 3745-2008 卡套式三通管接头 24° cone connectors.Union
tee
GB/T 3746-2008 卡套式四通管接头 24° cone connectors.
Union cross
GB/T 3747-2008 卡套式焊接管接头 24° cone connectors.Weld
male
GB/T 3748-2008 卡套式过板直通管接头 24° cone connectors.Bulkhead
union
GB/T 3749-2008 卡套式过板弯通管接头 24° cone connectors.Bulkhead
union elbow
GB/T 3750-2008 卡套式铰接管接头 24°cone connectors.Angle
swivel screw connector
GB/T 3751-2008 卡套式压力表管接头 24° cone connectors.Connector
for pressure gauge
GB/T 3752-2008 卡套式组合弯通管接头 24°cone connectors.Adjustable
elbow
GB/T 3753-2008 卡套式组合三通管接头 24° cone connectors.Adjustable
tee
GB/T 3754-2008 卡套式锥密封组合弯通管接头 24° cone connectors.Swivel
elbow with O-ring
GB/T 3755-2008 卡套式锥密封组合三通管接头 24°cone connectors.Branch
tee with O-ring
GB/T 3756-2008 卡套式锥密封组合直通管接头 24°cone connectors.Swivel
stud straight adapter with O-ring with stud
end
GB/T 3757-2008 套式过板焊接管接头 24° cone connectors.
Weld-in bulkhead straight connector
GB/T 3758-2008 卡套式管接头用锥密封焊接接管 24° cone connectors.
Weld-on nipple
GB/T 3759-2008 卡套式管接头用连接螺母 24°cone connectors.Nut
GB/T 3760-2008 卡套式管接头用锥密封堵头 24° cone connectors.Plug
with O-ring
GB/T 3761-1983 卡套式管接头用锥体环 Bite type tube fittings--Pressure
bush for butt joints
GB/T 3762-1983 卡套式管接头用尖角密封垫圈 Bite type tube
fittings--Tipping washer
GB/T 3763-2008 管接头用六角薄螺母 24°cone connectors
and flared couplings.Hexagon thin nut
GB/T 3765-2008 卡套式管接头技术条件 24°cone connectors.Specification
GB/T 5107-2008 气焊设备 焊接、切割和相关工艺设备用软管接头 Gas welding
equipment.Hose connections for equipment for
welding,cutting and allied processes
GB/T 5625-2008 扩口式直通管接头 FLared couplings-Straight
thread
GB/T 5626-2008 扩口式锥螺纹直通管接头 Flared couplings.Male
GB/T 5627-2008 扩口式锥螺纹长管接头 Flared couplings.Male
long
GB/T 5628-2008 扩口式直通管接头 Flared couplings.Union
GB/T 5629-2008 扩口式锥螺纹弯通管接头 Flared couplings.Male
elbow
GB/T 5630-2008 扩口式弯通管接头 Flared couplings. Union
elbow
GB/T 5631-2008 扩口式可调向端弯通管接头 Flared couplings.
Straight thread elbow
GB/T 5632-2008 扩口式组合弯通管接头 Flared couplings.Swivel
elbow
GB/T 5633-2008 扩口式可调向端三通管接头 Flared couplings.
Straight thread branch tee
GB/T 5634-2008 扩口式组合弯通二通管接头 Flared couplings.Swivel
run tee
GB/T 5635-2008 扩口式锥螺纹三通管接头 Flared couplings.Male
branch tee
GB/T 5637-2008 扩口式可调向端弯通三通管接头 Flared couplings.
Straight thread run tee
GB/T 5638-2008 扩口式组合三通管接头 Flared couplings.Swivel
branch tee
GB/T 5639-2008 扩口式三通管接头 Flared couplings-Union
tee
GB/T 5641-2008 扩口式四通管接头 Flared couplings.Union
cross
GB/T 5642-2008 扩口式焊接管接头 Flared couplings. Weld
male
GB/T 5643-2008 扩口式过板直通管接头 Flared couplings-Bulkhead
union
GB/T 5644-2008 扩口式过板弯通管接头 Flared couplings.
Bulkhead union elbow
GB/T 5645-2008 扩口式压力表管接头 Flared couplings.Connector
for pressure gauge
GB/T 5646-2008 扩口式管接头管套 Flared couplings. Sleeve
GB/T 5647-2008 扩口式管接头用A型螺母 Flared couplings.
Style A nut
GB/T 5648-2008 扩口式管接头用B型螺母 Flared couplings.
Style B nut
GB/T 5649-2008 管接头用锁紧螺母和垫圈 Flared couplings.Lock
nut and lockup washer
GB/T 5650-2008 扩口式管管接头用空心螺栓 Flared couplings.
Inverted flare bolts
GB/T 5651-2008 扩口式管接头用密合垫 Flared couplings.
Seat insert
GB/T 5652-2008 扩口式管接头扩口端尺寸 Flared couplings.Flared
end
GB/T 5653-2008 扩口式管接头技术条件 Flared couplings.
Specification
GB/T 5742-1999 船用饮水舱注入接头 Filling connection
for drinking water tanks on ships
GB/T 5860-2003 液压快换接头 尺寸和要求 Hydraulic fluid
power—Quick-action couplings Dimensions and
requirements
GB/T 5861-2003 液压快换接头 试验方法 Hydraulic fluid power-Quick
action couplings-Test methods
GB/T 5862-2008 农业拖拉机和机具.通用液压快换接头 Agricultural
tractors and machinery.General purpose quick-action
hydraulic couplers
GB/T 5973-2006 钢丝绳用楔形接头 Cuneiform connector
for use with steel wire ropes
GB/T 6329-1996 胶粘剂对接接头拉伸强度的测定 Adhesives--Determination
of tensile strength of butt joints
GB/T 6417.1-2005 金属熔化焊接头缺欠分类及说明 Classification
and explanation of imperfections in fusion welded
joints
GB/T 6417.2-2005 金属压力焊接头缺欠分类及说明 Classification
and explanation of imperfections in pressure
welded joints
GB/T 6661-1986 插入式耳机的乳头状接头 Nipples for insert
earphones
GB/T 6946-2008 钢丝绳铝合金压制接头 ()
GB/T 7937-2008 液压气动管接头及其相关元件.公称压力系列 Fluid power
systems and components.Connectors and associated
components.Nominal pressures
GB/T 7940.1-2008 气动.五气口方向控制阀.第1部分:不带电气接头的安装面
Pneumatic fluid power.Five-port directional
control valves.Part1:Mounting interface suifaces
without electrical connector
GB/T 7940.2-2008 气动.五气口方向控制阀.第2部分:带可选电气接头的安装面
Pneumatic fluid power.Five-port directional
control valves.Part2:Mounting interface surfaces
with optional electrical connector
GB/T 8259-2008 卡箍式柔性管接头.技术条件 Specification for
flexible joints of housing
GB/T 8260-2008 卡箍式柔性管接头.型式与尺寸 Types and dimensions
of flexible joints of housing
GB/T 8606-2003 液压快换接头螺纹连接尺寸及技术要求 Thread connecting
dimensions and specifications of hydraulic fluid
power-Quick action couplings
GB/T 9065.1-1988 液压软管接头 连接尺寸 扩口式 Hydraulic fluid
power--Hose connector--Connecting dimension
(Part 1--Flare type)
GB/T 9065.2-1988 液压软管接头 连接尺寸 卡套式 Hydraulic fluid
power--Hose connector--Connecting dimension
(Part 2--Insert type)
GB/T 9065.3-1988 液压软管接头 连接尺寸 焊接式或快换式 Hydraulic
fluid power--Hose connector--Connecting dimension(Part
3:Welding or quick-action type)
GB/T 9326.4-2008 交流500kV及以下纸或聚丙烯复合纸绝缘金属套充油电缆及附件.第4部分:
接头 Oil-filled,paper or polypropylene paper laminate
insulated,metal-sheathed cables and accessories
for alternating voltages up to and including
500 kV.Part 4:Joint
HD 623 S1-1996+A1-2001 额定电压 0.6/1.0 kV 配电电缆的接头、止动端和室外终端规范
Specification for joints, stop ends and outdoor
terminations for distribution cables of rated
voltage 0,6/1,0 kV / Note: To be replaced by
prEN 50393 (2003-07).
HG/T 2270-1992 内胎接头机 ()
HG/T 2289-2001 可曲挠橡胶接头 ()
HG/T 3196-2009 石墨外接头 ()
HG/T 3201-2009 石墨内接头 ()
HG/T 3652-1999 快装管接头 ()
JB/T 10708-2007 胶管接头扣压机 ()
JB/T 10740.2-2007 额定电压6kV(Um=7.2kV)到35kV(Um=40.5kV)挤包绝缘电力电缆
冷收缩式附件 第2部分：直通接头 Cold shrinkable accessories
for extruded insualtion power cables with rated
voltages from 6kV (Um=7.2kV) up to 35kV(Um=40.5kV)-Part
2:Straight joints
JB/T 1308.4-1999 橡胶密封真空规管接头 ()
JB/T 1308.5-1999 发电机锡焊接头检测方法 ()
JB/T 1308.9-1999 照相机 快线接头及快线座 ()
JB/T 1754-2008 阀门零部件 接头组件 ()
JB/T 2636-1994(2006年确认) 锅炉受压元件焊接接头金相和断口检验方法
()
JB/T 3411.17-1999 中间接头 尺寸 ()
JB/T 3411.21-1999 可调中心接头 尺寸 ()
JB/T 3947-1999 电阻点焊电极接头 ()
JB/T 5121-1991 额定电压26/35kV 及以下电力电缆附件基本技术要求 电缆接头
()
JB/T 5227.2-1991 气相色谱仪用管路附件 接头 ()
JB/T 5993-1992 管接头 检测方法 ()
JB/T 6144.1-2007 锥密封胶管总成 锥接头 ()
JB/T 6144.2-2007 锥密封胶管总成 55°非密封管螺纹锥接头 ()
JB/T 6144.3-2007 锥密封胶管总成 55o密封管螺纹锥接头 ()
JB/T 6144.4-2007 锥密封胶管总成 60°密封管螺纹锥接头 ()
JB/T 6144.5-2007 锥密封胶管总成 焊接锥接头 ()
JB/T 6381.1-2007 锥密封焊接式 直通管接头 ()
JB/T 6381.2-2007 锥密封焊接式 直通55°非密封管螺纹管接头 ()
JB/T 6381.3-2007 锥密封焊接式 直通55°密封管螺纹管接头 ()
JB/T 6381.4-2007 锥密封焊接式 直通60°密封管螺纹管接头 ()
JB/T 6382.1-2007 锥密封焊接式90o弯管接头 ()
JB/T 6382.2-2007 锥密封焊接式55o非密封管螺纹90o弯管接头 ()
JB/T 6382.3-2007 锥密封焊接式55o密封管螺纹90o弯管接头 ()
JB/T 6382.4-2007 锥密封焊接式60o密封管螺纹90o弯管接头 ()
JB/T 6383.1-2007 锥密封两端焊接式直通管接头 ()
JB/T 6383.2-2007 锥密封焊接式直角管接头 ()
JB/T 6383.3-2007 锥密封焊接式三通管接头 ()
JB/T 6384.1-2007 锥密封焊接式隔壁直角管接头 ()
JB/T 6384.2-2007 锥密封焊接式隔壁直通管接头 ()
JB/T 6385-2007 锥密封焊接式压力表管接头 ()
JB/T 6386-2007 锥密封焊接式管接头 技术条件 ()
JB/T 6464-2006 额定电压1kV(Um= 1.2kV)到35kV(Um =
40.5kV)挤包绝缘电力电缆绕包式直通接头 Taped straight joints
for extruded insulation power cables with rated
voltages from 1kV(Um=1.2kV) up to 35kV(Um=40.5kV)
JB/T 7056-2008 气动管接头 通用技术条件 ()
JB/T 7057-2008 调速式气动管接头 技术条件 ()
JB/T 7058-1993 快换式气动管接头 技术条件 ()
JB/T 7339-2007 挠性管接头 ()
JB/T 7830-2006 额定电压1kV（Um=1.2kV）到10kV（Um=12kV）挤包绝缘电力电缆热收缩式直通接头
Heat-shrinkable straight joints for extruded
insulation power cables with rated voltages
from 1kV(Um=1.2kV) up to 10kV(Um=12kV)
JB/T 7832-2006 额定电压1kV（Um=1.2kV）到10kV（Um=12kV）电力电缆树脂浇铸式直通接头
Cast resin straight joints for power cables
with rated voltages from 1kV(Um=1.2kV) up to
10kV(Um=12kV)
JB/T 7850-2007 手夹快换接头 ()
JB/T 7940.2-1995 接头式压注油杯 ()
JB/T 8105.2-1999 金属密封真空规管接头 ()
JB/T 8302-2000 农业拖拉机和机具液压输出快换接头 技术条件 ()
JB/T 8503.2-2006 额定电压6kV(Um = 7.2kV)到35kV(Um
= 40.5kV)挤包绝缘电力电缆预制件装配式附件 第2部分：直通接头 Premolded
accessories (slip-on type) for extruded insulation
power cables with rated voltages from 6kV(Um=7.2kV)
up to 35kV(Um=40.5kV) Part 2:Straight
JB/T 8725-1998 旋转接头 ()
JB/T 9162.17-1999 联动夹持杆接头 尺寸 ()
JB/T 9162.18-1999 夹持杆接头 尺寸 ()
JB/T 9465-1999 水密接头 ()
JB/T 966-2005 用于流体传动和一般用途的金属管接头 O形圈平面密封接头 ()
JB/T 978-1977 焊接式铰接管接头 ()
JB/T 9959-1999 电阻点焊 内锥度1:10的电极接头 ()
JB/T 998-1977 焊接式铰接管接头体 ()
JB/T 999-1977 管接头用铰接螺栓 ()
JC 538-1994 石棉水泥落水管、排污管及其接头 ()
JC 980-2005 纤维水泥电缆管及其接头 ()
JC/T 1091-2008 预应力钢筒混凝土管接头用型钢 ()
JJG(石油) 1-1996 石油钻具接头螺纹工作量规 ()
JJG(石油) 51-2000 石油钻具接头螺纹、套管圆螺纹和油管螺纹校对量规 检定规程
()
MT/T 153-1987 中心单链刮板输送机蛙形链接头 ()
MT/T 310-1992 高压水管楔式快速接头 ()
MT/T 318.1-1997 煤矿用输送带机械接头 技术条件 ()
MT/T 319－2006 煤矿输送带机械接头用带扣 ()
MT/T 986-2006 矿用U形销式快速接头及附件 ()
QB 1504-1992 实验室玻璃仪器互换锥形磨砂接头 ()
QB/T 2481-2000 旋转接头技术条件 ()
QC/T 201-1995(2005) 汽车气制动用热塑管接头尺寸 ()
QC/T 228.3-1997(2005) 摩托车和轻便摩托车操纵拉索 接头 ()
QC/T 29009-1991(2005) 汽车用电线接头 技术条件 ()
QC/T 29010-1991(2005) 汽车用低压电线接头型式、尺寸和技术要求 ()
QC/T 29011-1991(2005) 汽车用点火线电线接头型式、尺寸和技术要求 ()
QC/T 29013-1991(2005) 汽车用蓄电池电线接头型式、尺寸和技术要求 ()
QC/T 304-1999(2005) 汽车转向拉杆接头总成台架试验方法 ()
QC/T 327-1999(2005) 汽车用球头接头 ()
QC/T 399-1999(2005) 卡套式锥螺纹直通接头体 ()
QC/T 400-1999(2005) 卡套式锥螺纹直角三通接头体 ()
QC/T 401-1999(2005) 卡套式锥螺纹直角接头体 ()
QC/T 402-1999(2005) 卡套式锥螺纹三通接头体 ()
QC/T 403-1999(2005) 扩口式锥螺纹直通管接头体 ()
QC/T 404-1999(2005) 扩口式锥螺纹直角管接头体 ()
QC/T 405-1999(2005) 扩口式锥螺纹三通管接头体 ()
QC/T 669-2000(2005) 汽车空调(HFC-134a)用管接头和管件 ()
QC/T 701-2004 摩托车和轻便摩托车后减震器安装接头尺寸 Mounting of
rear shock absorbers for motorcycles and mopeds
QC/T 764-2006 汽车液压制动系 金属管、内外螺纹管接头和软管端部接头 ()
SB/T 10355-2002 制冷系统和热泵—软管件、隔振器和膨胀接头—要求、设计与安装
()
SY/T 0516-2008 绝缘接头与绝缘法兰技术规范 ()
SY/T 0525.2-1993 石油储罐回转接头 ()
SY/T 5067-1991(2005) 安全接头 ()
SY/T 5067-2008 安全接头 ()
SY/T 5200-2002 钻柱转换接头 ()
SY/T 5290-2000 石油钻杆接头 ()
SY/T 5988-1994 油管转换接头 ()
SY/T 6669-2006 端盖、联结件和旋转接头规范 Specification on
end closures,connectors and swivels
SY/T 6715-2008 钢管管接头焊接 ()
ISO接头标准(ISO joint standards)
--------------------------------------------------------------------------------
编号 中文名称 英文名称
IEC 61073-1-2009 纤维光学互连器件和无源元件.光学纤维和光缆用机械接头和熔融接头保护器.第1部分:通用规范
Fibre optic interconnecting devices and passive
components - Mechanical splices and fusion splice
protectors for optical fibres and cables - Part
1: Generic specification
IEC 61076-3-114-2009 电子设备用连接器.产品要求.第3-114部分:矩形连接器.合并IEC
60603-7系列接口的工业环境用频带在600MHz以下 Connectors for
electronic equipment - Product requirements
- Part 3-114: Rectangular connectors - Detail
specifications for protective housings for use
with 8-way shielded and unshielded connectors
for frequencies up to 600 MHz for industrial
environments incorporating the IEC 60603-7 series
interface - Variant 11 related to IEC 61076-3-106
- Bayonet coupling type
IEC 61188-5-8-2007 印制板和印制板组件.设计和使用.第5-8部分:附件(结合区/接头)考虑要素.区域阵列组件(BGA,
FBGA, CGA, LGA) Printed boards and printed board
assemblies - Design and use - Part 5-8: Attachment
(land/joint) considerations - Area array components
(BGA, FBGA, CGA, LGA)
IEC 62275-2006 电缆管理系统.电器设备用电缆接头 Cable management
systems - Cable ties for electrical installations
ISO 10042 Technical Corrigendum 1-2006 焊接.铝和铝合金的弧焊接头.缺陷质量分级.技术勘误1
Welding - Arc-welded joints in aluminium and
its alloys - Quality levels for imperfections;
Technical Corrigendum 1
ISO 10042-2005 焊接 铝和铝合金的弧焊接头 缺陷质量分级指南 Welding
- Arc-welded joints in aluminium and its alloys
- Quality levels for imperfections
ISO 1022-1988 航空航天 流体系统用气态氧充气接头(旧型) 尺寸(英制系列)
Aerospace; gaseous oxygen replenishment connection
for use in fluid systems (old type); dimensions
(inch series)
ISO 10321-2008 土工织物.用宽条法对接头/接缝处的拉伸试验 Geosynthetics
- Tensile test for joints/seams by wide-width
strip method
ISO 1034-1973 航空器 地面空气调节连接接头 Aircraft; Ground
air-conditioning connections
ISO 10955-1999 航空航天 航空器操纵钢丝绳用末端接头和松紧套筒 技术规范
Aerospace - End-fittings and turnbarrels for
aircraft control wire rope - Technical specification
ISO 10983-1999 木结构 实心木材指型接头 生产要求 Timber structures
- Solid timber finger-jointing - Production
requirements
ISO 11-1987 航空器 压力座舱的地面压力试验连接接头 Aircraft; Ground
pressure testing connections for pressure cabins
ISO 11144-1995 牙科设备 供水及排水管接头 Dental equipment
- Connections for supply and waste lines
ISO 1167-1-2006 流体传输用热塑管、接头和组件.抗内压力的测定.第1部分:通用方法
Thermoplastics pipes, fittings and assemblies
for the conveyance of fluids - Determination
of the resistance to internal pressure - Part
1: General method
ISO 1167-2-2006 流体传输用热塑管、接头和组件.抗内压力的测定.第2部分:管试件的准备
Thermoplastics pipes, fittings and assemblies
for the conveyance of fluids - Determination
of the resistance to internal pressure - Part
2: Preparation of pipe test pieces
ISO 12118-1995 航空货运设备 全向额定承载能力等于或高于22250N(50001bf)的双螺柱系留接头的识别标志
Air cargo equipment - Identification of double-stud
tie-down fittings having an omnidirectional
rated load capacity of 22250 N (5000 lbf) or
above
ISO 12151-1-1999 液压传动和通用联接件 软管接头 第1部分:带ISO 8434-3
O形圈端面密封末端的软管接头 Connections for hydraulic fluid
power and general use - Hose fittings - Part
1: Hose fittings with ISO 8434-3 O-ring face
seal ends
ISO 12151-2-2003 液压传动和通用联接件.软管接头.第2部分:带ISO 8434-1
O形圈24锥形末端的软管接头 Connections for hydraulic fluid
power and general use - Hose fittings - Part
2: Hose fittings with ISO 8434-1 24° cone connector
ends with O-rings
ISO 12151-3-1999 液压传动和通用联接件 软管接头 第3部分:带ISO6162法兰末端的软管接头
Connections for hydraulic fluid power and general
use - Hose fittings - Part 3: Hose fittings
with ISO 6162 flange ends
ISO 12151-4-2007 用于液压流体传动和一般用途的接头.软管配件.第4部分:带ISO
6149米制螺柱头的软管配件 Connections for hydraulic fluid
power and general use - Hose fittings - Part
4: Hose fittings with ISO 6149 metric stud ends
ISO 12151-5-2007 用于液压流体传动和一般用途的接头.软管配件.第5部分:带ISO
8434-2 37°扩口端的软管配件 Connections for hydraulic
fluid power and general use - Hose fittings
- Part 5: Hose fittings with ISO 8434-2 37°
flared ends
ISO 13486-1-1999 道路车辆 液压制动系统 第1部分:双喇叭口管、螺纹孔、阳螺纹管接头和管座
Road vehicles - Hydraulic braking systems -
Part 1: Double-flare pipes, tapped holes, male
fittings and tube seats
ISO 13919-1-1996 焊接 电子束和激光焊接头 缺陷的质量分级指南 第1部分:钢
Welding - Electron and laser-beam welded joints
- Guidance on quality levels for imperfections
- Part 1: Steel
ISO 13919-2-2001 焊接 电子束和激光束焊接接头 缺陷质量等级指南 第2部分：铝及其可焊合金
Welding - Electron and laser beam welded joints;
Guidance on quality levels for imperfections
- Part 2: Aluminium and its weldable alloys
ISO 13950 Technical Corrigendum 1-2008 塑料管和配件.电熔焊接头的自动识别系统.技术勘误1
Plastics pipes and fittings - Automatic recognition
systems for electrofusion joints; Technical
Corrigendum 1
ISO 13950-2007 塑料管和配件.电熔焊接头的自动识别系统 Plastics
pipes and fittings - Automatic recognition systems
for electrofusion joints
ISO 13953-2001 聚乙烯管材和管件 拉申强度的测定和熔接对接接头试件的失效模型
Polyethylene(PE) pipes and fittings - Determination
of the tensile strengt and failure mode of test
pieces from a butt-fused joint
ISO 14615-1997 粘合剂 结构型粘合剂粘结接头的耐久性 荷载下暴露在湿度和温度之中
Adhesives - Durability of structural adhesive
joints - Exposure to humidity and temperature
under load
ISO 1465-1989 航空器 液态氧充填接头 相配尺寸 Aircraft; liquid
oxygen replenishment couplings; mating dimensions
ISO 15171-1-1999 用于流体传动和一般用途的管接头 诊断用液压管接头 第1部分:非压力下连接的管接头
Connections for fluid power and general use
- Hydraulic couplings for diagnostic purposes
- Part 1: Coupling not for connection under
pressure
ISO 15171-2-2000 用于流体传动和一般用途的管接头 诊断用液压管接头 第2部分:带M16×2螺纹端的压力连接接头
Connections for fluid power and general use
- Hydraulic couplings for diagnostic purposes
- Part 2: Coupling with M16 × 2 end for connection
under pressure
ISO 15236-4-2004 钢丝传送带.第4部分:硫化带接头 Steel cord
conveyor belts - Part 4: Vulcanized belt joints
ISO 15407-1-2000 气压传动 五气口方向控制阀、规格18mm和26mm 第1部分:不带电接头的安装面
Pneumatic fluid power - Five-port directional
control valves, sizes 18 mm and 26 mm - Part
1: Mounting interface surfaces without electrical
connector
ISO 15509-2001 粘合剂 工程塑料接头粘合强度的测定 Adhesives -
Determination of the bond strength of engineering-plastic
joints
ISO 15614-8-2002 金属材料焊接程序的规范和鉴定.焊接程序试验.第8部分:管对管板接头焊接
Specification and qualification of welding procedures
for metallic materials - Welding procedure test
- Part 8: Welding of tubes to tube-plate joints
ISO 15615-2002 气焊设备.焊接、切割和相关工艺用乙炔复式接头系统.高压装置的安全要求
Gas welding equipment - Acetylene manifold systems
for welding, cutting and allied processes -
Safety requirements in high-pressure devices
ISO 15835-1-2009 混凝土增强钢.棒材制机械接头用增强耦合器.第1部分:要求
Steels for the reinforcement of concrete - Reinforcement
couplers for mechanical splices of bars - Part
1: Requirements
ISO 15835-2-2009 混凝土加固用钢.棒材机械接头用加固连接件.第2部分:试验方法
Steels for the reinforcement of concrete - Reinforcement
couplers for mechanical splices of bars - Part
2: Test methods
ISO 16028 AMD 1-2006 液压传动.在20MPa(200巴)至31.5MPa(315巴)压力下使用的平面对接型快速接头.规范.修改件1
Hydraulic fluid power - Flush-face type, quick-action
couplings for use at pressures of 20 MPa (200
bar) to 31,5 MPa (315 bar) - Specifications;
Amendment 1
ISO 16028-1999 液压传动 用于压力为20 MPa(200 bar)～31.5
MPa(315 bar)的平面对接型快速接头 规范 Hydraulic fluid power
- Flush-face type, quick-action couplings for
use at pressures of 20 MPa (200 bar) to 31,5
MPa (315 bar) - Specifications
ISO 16070-2005 石油和天然气工业.下井设备.锁芯轴和落地接头 Petroleum
and natural gas industries - Downhole equipment
- Lock mandrels and landing nipples
ISO 16422-2006 由定向未增塑聚(氯)乙烯(PVC-O)制成的用于压力下水运输的管道和接头.规范
Pipes and joints made of oriented unplasticized
poly(vinyl chloride) (PVC-O) for the conveyance
of water under pressure - Specifications
ISO 16670-2003 木结构.机械紧固件接头.准静态逆循环试验方法 Timber
structures - Joints made with mechanical fasteners
- Quasi-static reversed-cyclic test method
ISO 17636-2003 焊缝的无损检验.熔焊接头的放射检验 Non-destructive
testing of welds - Radiographic testing of fusion-welded
joints
ISO 17637-2003 焊缝的无损检验.熔焊接头的外观检验 Non-destructive
testing of welds - Visual testing of fusion-welded
joints
ISO 17640-2005 焊接的无损检验.焊接接头的超声波检验 Non-destructive
testing of welds - Ultrasonic testing of welded
joints
ISO 17653-2003 金属材料接头的破坏检验.电阻点焊的扭转试验 Destructive
tests on welds in metallic materials - Torsion
test of resistance spot welds
ISO 17659-2002 焊接.图示焊接接头的多语种术语 Welding - Multilingual
terms for welded joints with illustrations
ISO 1813-1998 带传动 多楔带、有接头V带、宽截面带及六角带 抗静电带的电导率:特性和试验方法
Belt drives - V-ribbed belts, joined V-belts
and V-belts including wide section belts and
hexagonal belts - Electrical conductivity of
antistatic belts: Characteristics and methods
of test
ISO 18279-2003 钎焊.钎焊接头的缺陷 Brazing - Imperfections
in brazed joints
ISO 18672-1-2009 塑料无压埋地排水管管道系统.聚酯混凝土(PRC).第1部分:连接管子和配件的柔性接头.
Plastics piping systems for non-pressure drainage
and sewerage - Polyester resin concrete (PRC)
- Part 1: Pipes and fittings with flexible joints
ISO 1966-1973 航空器电缆的压接接头 Crimped joints for
aircraft electrical cables
ISO 2016-1981 铜管用毛细管焊接接头 组装尺寸和试验方法 Capillary
solder fittings for copper tubes; Assembly dimensions
and tests
ISO 2048-1990 弹性密封圈型接头的硬聚氯乙烯(PVC-U)压力管的双承口 最小配合深度
Double-socket fittings for unplasticized poly(vinyl
chloride) (PVC-U) pressure pipes with elastic
sealing ring type joints; minimum depths of
engagement
ISO 21004-2006 塑料管道系统.供水用基于热塑性塑料的多层管道及其接头 Plastics
piping systems - Multilayer pipes and their
joints, based on thermoplastics, for water supply
ISO 21809-3-2008 石油和天然气工业.管道运输系统用掩埋于地下或淹没于水下的管道外部覆层.第2部分:安装接头涂层
Petroleum and natural gas industries - External
coatings for buried or submerged pipelines used
in pipeline transportation systems - Part 3:
Field joint coatings
ISO 22826-2005 金属材料焊缝的破坏性试验.激光和电子束焊接窄接头的硬度试验(维氏和努氏硬度试验)
Destructive tests on welds in metallic materials
- Hardness testing of narrow joints welded by
laser and electron beam (Vickers and Knoop hardness
tests)
ISO 23711-2003 弹性密封件.灌溉和排水设施用管接头密封件材料的要求.弹性塑料
Elastomeric seals - Requirements for materials
for pipe joint seals used in water and drainage
applications - Thermoplastic elastomers
ISO 2531-1998 输水和输气用球墨铸铁管、配件、附件及其接头 Ductile
iron pipes, fittings, accessories and their
joints for water or gas applications
ISO 2553-1992 焊接、硬钎焊和软钎焊接头 图样上的符号表示法 Welded,
brazed and soldered joints; symbolic representation
on drawings
ISO 2974-2005 柴油机.60度锥孔的高压油管接头管端部连接 Diesel engines
- High-pressure fuel injection pipe end-connections
with 60 degrees female cone
ISO 3174-1994 航空器 用地面设备检查液压系统的连接接头 螺纹式 Aircraft
- Connections for checking hydraulic systems
by ground appliances - Threaded type
ISO 3253-1998 气焊设备 焊接、切割和有关工艺设备的软管接头 Gas welding
equipment - Hose connections for equipment for
welding, cutting and allied processes
ISO 3458-1976 聚乙烯(PE)压力管材和管件间的装配接头 内压密封试验 Assembled
joints between fittings and polyethylene (PE)
pressure pipes ; Test of leakproofness under
internal pressure
ISO 3459-1976 聚乙烯(PE)压力管 用机械式管件装配的接头 内压试验法和要求
Polyethylene (PE) pressure pipes; Joints assembled
with mechanical fittings; Internal under-pressure
test method and requirement
ISO 3460-1975 硬聚氯乙烯(PVC)压力管材 公制系列 凹法兰管接头尺寸 Unplasticized
polyvinyl chloride (PVC) pressures pipes; Metric
series; Dimensions of adapter for backing flange
ISO 3501-1976 聚乙烯(PE)压力管材和管件间的装配接头 抗拉拔试验 Assembled
joints between fittings and polyethylene (PE)
pressure pipes; Test of resistance to pull out
ISO 3503-1976 聚乙烯(PE)压力管材和管件间的装配接头 弯曲时承受内压的密封试验
Assembled joints between fittings and polyethylene
(PE) pressure pipes; Test of leakproofness under
internal pressure when subjected to bending
ISO 3553-1-1987 道路车辆 点火线圈和分电器的高压接头 第1部分:插座型
Road vehicles; High-tension connections for
ignition coils and distributors; Part 1 : Socket-type
ISO 3553-2-1997 道路车辆 点火线圈和分电器的高压接头 第2部分:插头型
Road vehicles - High-tension connectors for
ignition coils and distributors - Part 2: Plug-types
ISO 3926-1980 造船 内河航行 滑油和燃料输入管接头、配合尺寸 Shipbuilding;
Inland navigation; Couplings for oil and fuel
reception; Mating dimensions
ISO 4038-1996 道路车辆 液压制动系统 单喇叭口管、螺孔和阳螺纹接头和软管管端接头
Road vehicles - Hydraulic braking systems -
Simple flare pipes, tapped holes, male fittings
and hose end fittings
ISO 4039-1-1998 道路车辆 气压制动系统 第1部分:有平面密封面的管、阳螺纹管接头和螺纹孔
Road vehicles - Pneumatic braking systems -
Part 1: Pipes, male fittings and tapped holes
with facial sealing surface
ISO 4039-2-1998 道路车辆 气压制动系统 第2部分:有锥形密封面的管、阳螺纹管接头和螺纹孔
Road vehicles - Pneumatic braking systems -
Part 2: Pipes, male fittings and tapped holes
with conical sealing surface
ISO 4132-1979 承压管用硬聚氯乙烯(PVC)和金属的接头管件安装长度和螺纹尺寸
公制系列 Unplasticized polyvinyl chloride (PVC)
and metal adaptor fittings for pipes under pressure;
Laying lengths and size of threads; Metric series
ISO 4347-2004 板式链、端接头及槽轮.尺寸、计量力和抗拉强度 Leaf chains,
clevises and sheaves - Dimensions, measuring
forces and tensile strengths
ISO 4397-1993 流体传动系统和元件 管接头及其附件 硬管外径和软管内径 Fluid
power systems and components; connectors and
associated components; nominal outside diameters
of tubes and nominal inside diameters of hoses
ISO 4399-1995 流体传动系统和元件 管接头及其附件 公称压力系列 Fluid
power systems and components - Connectors and
associated components - Nominal pressures
ISO 4434-1977 承压管用硬聚氯乙烯(PVC)接头管件 安装长度和螺纹尺寸 公制系列
Unplasticized polyvinyl chloride (PVC) adaptor
fittings for pipes under pressure; Laying length
and size of threads; Metric series
ISO 45-1990 航空器 压力加油接头 Aircraft; pressure refuelling
connections
ISO 451-1976 飞机.压力加注润滑油接头 Aircraft; Pressure
re-oiling connection
ISO 485-1973 航空器的水-甲醇压力加注接头 Aircraft water-methanol
pressure connections
ISO 49 Technical Corrigendum 1-1997 符合ISO 7-1可锻铸铁管螺纹接头
技术勘误1 Malleable cast iron fittings threaded
to ISO 7-1; Technical Corrigendum 1
ISO 49-1994 符合ISO 7-1可锻铸铁管螺纹接头 Malleable cast
iron fittings threaded to ISO 7-1
ISO 5031-1977 松散物料连续搬运设备 气力输送用接头和软管 安全规则 Continuous
mechanical handling equipment for loose bulk
materials; Couplings and hose components used
in pneumatic handling; Safety code
ISO 5178-2001 金属材料焊接的破坏性试验 熔焊接头的焊接金属的纵向拉申试验
Destructive tests on welds in metallic materials
- Longitudinal tensile test on weld metal in
fusion welded joints
ISO 5183-1-1998 电阻焊设备 外锥度1:10电极接头 第10部分:锥度1:10圆锥形接头
Resistance welding equipment - Electrode adaptors,
male taper 1:10 - Part 1: Conical fixing, taper
1:10
ISO 5183-2-2000 电阻点焊 外锥度1:10电极接头 第2部分:端推力电极用平行柄接头
Resistance spot welding - Electrode adaptors,
male taper 1:10 - Part 2: Parallel shank fixing
for end-thrust electrodes
ISO 5187-1985 焊接和相关工艺 用软钎焊和硬钎焊接头 力学试验方法 Welding
and allied processes; Assemblies made with soft
solders and brazing filler metals; Mechanical
test methods
ISO 5290-2001 带传动 带接头的窄V带槽轮 槽形截面为9N/J、15N/J和25N/J(有效系列)
Belt drives - Grooved pulleys for narrow V-belts
- Groove sections 9N/J, 15N/J and 25N/J (effective
system)
ISO 5291-1993 带传动 带接头的三角V带槽轮 槽形截面为AJ、BJ、CJ和DJ(有效系列)
Belt drives; grooved pulleys for joined classical
V-belts; groove sections AJ, BJ, CJ and DJ (effective
system)
ISO 5356-1-2004 麻醉和呼吸设备.锥形接头.第1部分:锥体和锥套 Anaesthetic
and respiratory equipment - Conical connectors
- Part 1: Cones and sockets
ISO 5356-2-2006 麻醉和呼吸设备.圆锥形接头.第2部分:螺纹承重接头 Anaesthetic
and respiratory equipment - Conical connectors
- Part 2: Screw-threaded weight-bearing connectors
ISO 5366-1-2000 麻醉和呼吸设备 气管造口插管 第1部分:成人用插管和接头
Anaesthetic and respiratory equipment - Tracheostomy
tubes - Part 1: Tubes and connectors for use
in adults
ISO 5599-1-2001 气压传动 五气口方向控制阀 第1部分:不带电接头的安装面
Pneumatic fluid power - Five-port directional
control valves - Part 1: Mounting interface
surfaces without electrical connector
ISO 5599-2 AMD 1-2004 气压传动.五气口方向控制阀.第2部分:带可选电接头的安装面.修改件1
Pneumatic fluid power - Five-port directional
control valves - Part 2: Mounting interface
surfaces with optional electrical connector;
Amendment 1
ISO 5599-2-2001 气压传动 五气口方向控制阀 第2部分:带可选电接头的安装面
Pneumatic fluid power - Five-port directional
control valves - Part 2: Mounting interface
surfaces with optional electrical connector
ISO 5620-1-1992 造船及海上结构物 饮水舱的注水接头 第1部分:一般要求
Shipbuilding and marine structures; filling
connection for drinking water tanks; part 1:
general requirements
ISO 5620-2-1992 造船及海上结构物 饮水舱的注水接头 第2部分:零件 Shipbuilding
and marine structures; filling connection for
drinking water tanks; part 2: components
ISO 5675-2008 农业拖拉机和机械.一般用快速液压接头 Agricultural
tractors and machinery - General purpose quick-action
hydraulic couplers
ISO 5676-1983 农林用拖拉机和机械 液压接头 制动回路 Tractors and
machinery for agriculture and forestry; Hydraulic
coupling; Braking circuit
ISO 5817-2003 焊接.钢、镍、钛及其合金熔焊接头(束焊除外).缺陷的质量分级
Welding - Fusion-welded joints in steel, nickel,
titanium and their alloys (beam welding excluded)
- Quality levels for imperfections
ISO 5821-2009 电阻焊接.点焊电极帽接头 Resistance welding
- Spot welding electrode caps
ISO 5828-2001 电阻焊设备 连接水冷接头的二次连接电缆 尺寸及特性 Resistance
welding equipment - Secondary connecting cables
with terminals connected to water-cooled lugs
- Dimensions and characteristics
ISO 5829-1984 电阻点焊 内锥度为1:10的电极接头 Resistance
spot welding; Electrode adaptors, female taper
1 : 10
ISO 5855-3-1999 航空航天 MJ螺纹 第3部分:液体系统管接头螺纹系统的极限尺寸
Aerospace - MJ threads - Part 3: Limit dimensions
for fittings for fluid systems
ISO 5866-1983 航空器 有扁接头的2型和3A型插座式的换向继电器 间隙和固定尺寸
Aircraft; 2 and 3A plug-in base change-over
relays, Type II, with crimped connections; Clearance
and fixing dimensions
ISO 5887-1981 航空器 乘务员用调压面罩与氧气源的连接接头 Aircraft;
Joints for connecting crew members' regulator
masks to oxygen sources
ISO 594-1-1986 注射器、针头及其他医疗器械为6%(鲁尔)的锥形接头 第1部分:一般要求
Conical fittings with a 6 % (Luer) taper for
syringes, needles and certain other medical
equipment; Part 1 : General requirements
ISO 594-2-1998 注射器、针头及其他医疗器械为6%(鲁尔)的锥形接头 第2部分:锁紧接头
Conical fittings with 6% (Luer) taper for syringes,
needles and certain other medical equipment
- Part 2: Lock fittings
ISO 6038-1993 电影 70mm、65mm、35mm和16mm电影影片接头 尺寸和位置
Cinematography; splices for use on 70 mm, 65
mm, 35 mm and 16 mm motion-picture films; dimensions
and locations
ISO 610-1990 刮板输送机和刨煤机用高强度钢链带(无接头无形连接) High-tensile
steel chains (round link) for chain conveyors
and coal ploughs
ISO 6149-1-2006 用于液压流体传动和一般用途的管接头.带ISO 261螺纹和O形圈密封的油口和螺纹端头.第1部分:带锪孔沟槽中装有
Connections for hydraulic fluid power and general
use - Ports and stud ends with ISO 261 metric
threads and O-ring sealing - Part 1: Ports with
truncated housing for O-ring seal
ISO 6149-2-2006 用于液压传动和一般用途的管接头.带ISO 261螺纹和O形圈密封的油口和螺纹端头.第2部分:重型(S系列)螺柱端头
Connections for hydraulic fluid power and general
use - Ports and stud ends with ISO 261 metric
threads and O-ring sealing - Part 2: Dimensions,
design, test methods and requirements for heavy-duty
(S series) stud ends
ISO 6149-3-2006 用于液压传动和一般用途的管接头.带ISO 261螺纹和O形圈密封的油口和螺纹端头.第3部分:轻型(L系列)螺柱端头
Connections for hydraulic fluid power and general
use - Ports and stud ends with ISO 261 metric
threads and O-ring sealing - Part 3: Dimensions,
design, test methods and requirements for light-duty
(L series) stud ends
ISO 6149-4-2006 用于传动和一般用途的管接头.带ISO 261螺纹和O形圈密封的油口和螺纹端头.第4部分:内外六角气门栓的尺寸、设
Connections for fluid power and general use
- Ports and stud ends with ISO 261 metric threads
and O-ring sealing - Part 4: Dimensions, design,
test methods and requirements for external hex
and internal hex port plugs
ISO 6150-1988 气压传动 最高工作压力为10 bar、16 bar和25 bar(1
MPa、1.6 MPa和2.5 MPa)圆柱形快换接头、插头、连接尺寸 Pneumatic
fluid power; cylindrical quick-action couplings
for maximum working pressures of 10 bar, 16
bar and 25 bar (1 MPa, 1,6 MPa and 2,5 MPa);
plug connecting dimensions, specifications,
application guidelines and testing
ISO 6455-1983 承压管用带弹性密封圈型接头的硬聚氯乙烯(PVC)管件 安装长度的测定
公制系列 Unplasticized polyvinyl chloride (PVC)
fittings with elastic sealing ring type joints
for pipes under pressure; Dimensions of laying
lengths; Metric series
ISO 6696-1989 自行车 用于中接头装配的螺纹 Cycles; screw threads
used in bottom bracket assemblies
ISO 6699-1990 自行车 把横管和把立管接头 装配尺寸 Cycles; stem
and handlebar bend; assembly dimensions
ISO 6772-1988 航空航天 流体系统 液压软管、导管和接头组件的冲击试验 Aerospace;
fluid systems; impulse testing of hydraulic
hose, tubing and fitting assemblies
ISO 6891-1983 木结构 机械紧固件接头 强度和变形特性确定的一般原则 Timber
structures; Joints made with mechanical fasteners;
General principles for the determination of
strength and deformation characteristics
ISO 7169-2007 航空航天.液压系统用24°锥形的、压力范围截至3000psi或21000kPa的可拆卸管接头.采购规范(英制/米制)
Aerospace - Separable tube fittings for fluid
systems, for 24° cones, for pressures up to
3000 psi or 21000 kPa - Procurement specification,
inch/metric
ISO 7241-1-1987 液压传动 快换接头 第1部分:尺寸和要求 Hydraulic
fluid power; Quick-action couplings; Part 1
: Dimensions and requirements
ISO 7241-2-2000 液压传动 快换接头 第2部分:试验方法 Hydraulic
fluid power - Quick-action couplings - Part
2: Test methods
ISO 7257-1983 航空器 液压管接头和连接接头扭转弯曲试验 Aircraft;
Hydraulic tubing joints and fittings; Rotary
flexure test
ISO 7289-1996 气焊、切割及相关工艺用带关闭阀的快速接头 Quick-action
couplings with shut-off valves for gas welding,
cutting and allied processes
ISO 7319-1992 航空航天.流体系统.24°锥孔米制管接头的接口 Aerospace;
fluid systems; interface of 24° cone metric
couplings
ISO 7320-1992 航空航天 流体系统螺纹密封连接接头 尺寸 Aerospace;
couplings, threaded and sealed, for fluid systems;
dimensions
ISO 7803-1987 商用道路车辆 转向球接头 Commercial road vehicles;
Steering ball joints
ISO 7876-4-2004 燃油喷射装置.词汇.第4部分:高压管和末端接头 Fuel
injection equipment - Vocabulary - Part 4: High-pressure
pipes and end-connections
ISO 8056-4-1987 航空器 镍铬和镍铝热电偶的延伸电缆 第4部分:压接式对接接头
尺寸 Aircraft; Nickel-chromium and nickel-aluminium
thermocouple extension cables; Part 4 : Crimp-type
butt connectors; Dimensions
ISO 8092-1-1996 道路车辆 车载电气线束的连接 第1部分:单极联接接头 尺寸和特殊要求
Road vehicles - Connections for on-board electrical
wiring harnesses - Part 1: Tabs for single-pole
connections; dimensions and specific requirements
ISO 8092-3-1996 道路车辆 车载电气线束的连接 第3部分:多极连接接头 尺寸和特殊要求
Road vehicles - Connections for on-board electrical
wiring harnesses - Part 3: Tabs for multi-pole
connections; dimensions and specific requirements
ISO 8267-1-2005 飞行器.牵引杆附属接头的接口要求.第1部分:干线飞行器
Aircraft - Tow bar attachment fittings interface
requirements - Part 1: Main line aircraft
ISO 8267-2-2005 飞行器.牵引杆附属接头的接口要求.第2部分:地方飞行器
Aircraft - Tow bar attachment fittings interface
requirements - Part 2: Regional aircraft
ISO 8434-1-2007 液压传动和通用金属管连接件.第1部分:24°锥形接头 Metallic
tube connections for fluid power and general
use - Part 1: 24° cone connectors
ISO 8434-2-2007 液压传动和通用金属管连接件.第2部分:37°扩口管接头
Metallic tube connections for fluid power and
general use - Part 2: 37° flared connectors
ISO 8434-3-2005 用于流体传动和一般用途的金属管接头.第3部分:O形圈端面密封管接头
Metallic tube connections for fluid power and
general use - Part 3: O-ring face seal connectors
ISO 8483-2003 玻璃增强热固性塑料管及配件.栓结法兰接头设计验证的试验方法
Glass-reinforced thermosetting plastics (GRP)
pipes and fittings - Test methods to prove the
design of bolted flange joints
ISO 8533-2003 玻璃增强热固性塑料管及配件.胶合接头或包好的接头设计验证的试验方法
Glass-reinforced thermosetting plastics (GRP)
pipes and fittings - Test methods to prove the
design of cemented or wrapped joints
ISO 8775-1988 航空航天 流体系统用气氧充填接头(新型) 尺寸(英制) Aerospace;
gaseous oxygen replenishment connection for
use in fluid systems (new type); dimensions
(inch series)
ISO 8793-1986 钢丝绳 套圈卡紧环眼接头 Steel wire ropes;
Ferrule-secured eye terminations
ISO 8795-2001 输送人类生活用水用塑料管道系统 流动评定 塑料管道和管件及其接头的流动值的测定
Plastics piping systems for the transport of
water intended for human consumption - Migration
assessment - Determination of migration values
of plastics pipes and fittings and their joints
ISO 8820-3-2002 道路车辆.熔断体.第3部分:带接头的熔断体(刀闸) Road
vehicles - Fuse-links - Part 3: Fuse-links with
tabs (blade type)
ISO 8969-1990 木结构 单侧冲孔金属板紧固件和接头的试验 Timber structures;
testing of unilateral punched metal plate fasteners
and joints
ISO 8970-1989 木结构 机械紧固件接头的试验 对木材密度要求 Timber
structures; testing of joints made with mechanical
fasteners; requirements for wood density
ISO 9015-1-2001 金属材料焊接的破坏性试验 硬度试验 第1部分：弧焊接头的硬度试验
Destructive tests on welds in metallic materials
- Hardness testing - Part 1: Hardness test on
arc welded joints
ISO 9538-1996 航空航天 液压管路安装接头及管接头 平面弯曲试验 Aerospace
- Hydraulic tubing joints and fittings - Planar
flexure test
ISO 9623-1997 压力流体用聚乙烯(PE)/金属和聚丙烯(PP)/金属接头管件
螺纹的设计长度和尺寸 公制系列 PE/metal and PP/metal adaptor
fittings for pipes for fluids under pressure
- Design lengths and size of threads - Metric
series
ISO 9624-1997 压力流体用热塑性塑料管材 法兰接头和活套法兰的适配尺寸 Thermoplastics
pipes for fluids under pressure - Mating dimensions
of flange adapters and loose backing flanges
ISO 9691-1992 橡胶 管接头的密封件制造工艺的建议 缺陷类型和描述 Rubber;
recommendations for the workmanship of pipe
joint rings; description and classification
of imperfections
ISO 9692-2-1998 焊接和相关工艺 接头的制备 第2部分:钢的埋弧焊 Welding
and allied processes - Joint preparation - Part
2: Submerged arc welding of steels
ISO 9692-3-2000 焊接和相关工艺 接头制备的建议 第3部分:铝及铝合金的金属焊条惰性气体保护焊和钨焊条惰性气体保护焊
Welding and allied processes - Recommendations
for joint preparation - Part 3: Metal inert
gas welding and tungsten inert gas welding of
aluminium and its alloys
ISO 9692-4-2003 焊接和相关工艺.接头制备的建议.第4部分:包钢 Welding
and allied processes - Recommendations for joint
preparation - Part 4: Clad steels
ISO 9788-1990 航空货运设备 固定航空货物用承载能力为22250N(5000lbf)双螺柱接头的铸件
Air cargo equipment; cast components of double
stud fitting assembly with a load capacity of
22250 N (5000 lbf), for aircraft cargo restraint
ISO 9939-1994 航空航天 滑油的压力加油接头(新型) Aerospace;
pressure re-oiling connection (new type)
ISO/TR 5987-1984 内河航行 喷水灭火系统 灭火水龙带连接头 一般技术要求
Inland navigation; Water fire-fighting system;
Couplings of fire hoses; General technical requirements
日本接头标准(JIS joint standards)
--------------------------------------------------------------------------------
Purchasing Guide English Japanese Chinese 编号
中文名称
日本語標題 英文名称
JIS A1611-1996 木砖粘合剂及其中的胶接接头粘合强度的试验方法
木れんが用接着剤の接着強さ及びその接着工法の接着強さ試験方法 Testing methods
for bond strength of adhesives and of installed
glue-joints in anchoring wooden block
JIS A1612-1996 墙和天花板的粘合剂及其中的胶接接头粘合强度的试验方法
壁?天井ボード用接着剤の接着強さ及びその接着工法の接着強さ試験方法 Testing methods
for bond strength of adhesives and of installed
glue-joints in wall and ceiling boards
JIS B1552-2005 滚动轴承.接头组件、紧固套和退卸套
転がり軸受－アダプタ，アダプタスリーブ及び取外しスリーブ Rolling bearings
-- Adapter assemblies, Adapter sleeves and Withdrawal
sleeves
JIS B2301-2004 螺纹式可锻铸铁管接头
ねじ込み式可鍛鋳鉄製管継手 Screwed type malleable cast iron
pipe fittings
JIS B2303-1995 螺纹连接式排水管接头
ねじ込み式排水管継手 Screwed drainage fittings
JIS B2308-2002 不锈钢制带螺纹的管接头
ステンレス鋼製ねじ込み継手 Stainless steel threaded fittings
JIS B2321-1995 铝及铝合金对焊接管接头
配管用アルミニウム及びアルミニウム合金製突合せ溶接式管継手 Aluminium and
aluminium alloy butt-welding pipe fittings
JIS B2321 AMD 1-2009 铝及铝合金对焊接管接头(修改件1)
配管用アルミニウム及びアルミニウム合金製突合せ溶接式管継手（追補１） Aluminium
and aluminium alloy butt-welding pipe fittings
(Amendment 1)
JIS B2351-1 ERRATUM 1-2000 流体动力用和通用的金属管连接件.第1部分:24度SIGN压合管接头(勘误1)
Metallic tube connections for fluid power and
general use -- Part 1: 24 degree SIGN compression
fittings (Erratum 1)
JIS B2351-1 ERRATUM 2-2002 流体动力和通用金属管连接件.第1部分:24度SIGN压合接头(勘误2)
Metallic tube connections for fluid power and
general use -- Part 1: 24 degree SIGN compression
fittings (Erratum 2)
JIS B2351-1-2000 液力和一般用途金属管接头.第1部分.24度SIGN压合接头
油圧?空気圧用及び一般用途用金属製管継手 ― 第１部：２４°くい込み式管継手 Metallic
tube connections for fluid power and general
use -- Part 1: 24 degree SIGN compression fittings
JIS B2351-5-2000 液力和一般用途金属管接头.第5部分.螺纹液压动力接头的试验方法
油圧?空気圧用及び一般用途用金属製管継手 ― 第５部：油圧用ねじ継手の試験方法 Metallic
tube connections for fluid power and general
use -- Part 5: Test methods for threaded hydraulic
fluid power connections
JIS B2352-2005 波纹管型膨胀接头
ベローズ形伸縮管継手 Bellows type expansion joints
JIS B2356-1-2001 一般用途的和流体动力用接头.带弹性密封件或金属与金属间密封件的ISO
261螺纹的端口和螺柱端头.第1部分:螺
油圧?空気圧用及び一般用途用管継手 ― エラストマシール又はエッジシールによるメートルねじポート及び継手端部 ― 第１部：メートルねじポート
Connections for general use and fluid power
-- Ports and stud ends with ISO 261 threads
with elastomeric or metal-to-metal sealing --
Part 1: Threaded ports
JIS B2358-1-2001 一般用途的和流体动力用接头.带ISO 261螺纹和O形环密封件的端口和螺柱端头.第1部分:在截断外壳体内装有O形
油圧?空気圧用及び一般用途用管継手 ― Ｏリングシールによるユニファイねじポート及び継手端部 ― 第１部：ユニファイねじＯリングシールポート
Connections for general use and fluid power
-- Ports and stud ends with ISO 725 threads
and O-ring sealing -- Part 1: Ports with O-ring
seal in truncated housing
JIS B7284-1997 眼镜架的焊接接头
眼鏡枠用溶接丁番 Welded joints for spectacle frames
JIS B8363-2000 液压软管组件的端部配件及接头
液圧用ホースアセンブリ継手金具及び附属金具 End fittings and adapters
for hydraulic hose assemblies
JIS B9119-1989 喷雾器用软管联接器和软管接头
噴霧機用ホース継手及びホースつなぎ Hose couplings and hose joints
for sprayer
JIS B9911-1968 消防水龙管插入式接头的尺寸
消防用ホースの差込み式結合金具の寸法 Dimensions of insert type
couplings for fire-hose
JIS C8330 ERRATUM 1-2000 刚性金属导管的接头(勘误)
金属製電線管用の附属品 Fittings for rigid metal conduits
(Erratum 1)
JIS C8432 ERRATUM 1-2000 未增塑的聚氯乙烯(PVC-U)导管接头(勘误
1)
硬質塩化ビニル電線管用附属品 Fittings of unplasticized polyvinyl
chloride (PVC-U) conduits (Erratum 1)
JIS D5403-1989 汽车用电缆终端接头
自動車用電線端子 Cable terminals for automobiles
JIS E3023-1992 绝缘轨道接头的绝缘材料.试验方法
レール絶縁材料 ― 性能試験方法 Insulating materials of insulated
rail joint -- Test methods
JIS E3023 AMD 1-2006 绝缘轨道接头的绝缘材料.试验方法(修改件1)
レール絶縁材料―性能試験方法（追補１） Insulating materials of
insulated rail joint -- Test methods (Amendment
1)
JIS E4047-2008 铁路车辆.车辆底架.焊接接头的设计方法
鉄道車両―旅客車用構体―溶接継手設計方法 Rolling stock -- Body frame
-- Design methods for welded joints
JIS E4048-2008 车辆.客车的车体结构.点焊接头的设计方法
鉄道車両―旅客車用構体―スポット溶接継手の設計方法 Rolling stock -- Body
structure for passenger cars -- Design method
for spot-welded joints
JIS F1027-1997 小艇.燃油管的接头
舟艇 ― 燃料給油系ホースのはめあい部 Small crafts -- Joint of
fuel hoses
JIS F7020-1996 造船.带吊环螺栓的螺纹接头
船用アイボルト付ターンバックル Shipbuilding -- Turnbuckles
with eye bolts
JIS F7379-1996 造船.黄铜制带咬合接头的30K截止阀
船用黄銅３０Ｋくい込形止め弁 Shipbuilding -- Brass 30K stop
valves with bite joint(s)
JIS F7452-1978 船舶用通用接头
船用自在継手 Marine universal joints
JIS F7453-1978 船舶用传动轴接头
船用伝動軸継手 Marine transmission shaft joints
JIS F7454-1978 船舶用传动轴活动接头
船用伝動軸伸縮継手 Marine transmission shaft loose joints
JIS F7810-1995 造船焊接.钢管用套筒型接头
船用鋼製溶接スリーブ式管継手 Shipbuilding -- Welding sleeve
type joints for steel pipe
JIS K6813-2002 聚烯烃管和管接头.用焙烧和热解测定炭黑含量.试验方法和基本规范
ポリオレフィン管及び継手 ― 灰化及び熱分解によるカーボンブラック含有量の求め方 ― 試験方法及び基本仕様
Polyolefin pipes and fittings -- Determination
of carbon black content by calcination and pyrolysis
-- Test method and basic specification
JIS K7014-1997 增强式纤维塑料管道用配件和接头
繊維強化プラスチック管継手 Fittings and joints for fibre
reinforced plastic pipes
JIS K7036-1998 塑料管道系统.玻璃纤维增强热固性塑料(GRP)管道和配件.螺栓法兰接头设计的检定试验方法
プラスチック配管系 ― ガラス強化熱硬化性プラスチック（ＧＲＰ）管及び継手 ― ボルト式フランジ接合部の試験方法
Plastics piping systems -- Glass-reinforced
thermosetting plastics (GRP) pipes and fittings
-- Test method to prove the design of bolted
flange joints
JIS K7042-1998 塑料管道系统.玻璃纤维增强热固性塑料(GRP)管道和配件.粘合的或绕接的钢性接头设计的检定试验方法
プラスチック配管系 ― ガラス強化熱硬化性プラスチック（ＧＲＰ）管及び継手 ― 接着又は積層接合部の試験方法
Plastics piping systems -- Glass-reinforced
thermosetting plastics (GRP) pipes and fittings
-- Test methods to prove the design of cemented
or wrapped rigid joints
JIS R1624-1995 精细陶瓷接头抗弯曲强度的测试方法
ファインセラミックス接合の曲げ強さ試験方法 Testing method for bending
strength of fine ceramic joint
JIS R3646-1997 可互换式锥形玻璃磨口接头
化学分析用ガラス器具の共通テーパーすり接手 Interchangeable conical
glass ground joints
JIS R3651-1997 可互换式球面磨口玻璃接头
化学分析用ガラス器具の共通球面すり接手 Interchangeable spherical
ground glass joints
JIS W1832-2002 航空航天系列.流体系统.管件和管接头组件的试验方法
航空宇宙 ― 流体系統 ― 管?継手組立の試験方法 Aerospace -- Fluid
systems -- Test methods for tube/fitting assemblies
JIS Z3090-2005 熔焊接头的目测试验方法
溶融溶接継手の外観試験方法 Visual testing method of fusion-welded
joints
JIS Z3103-1987 熔焊接头重复拉伸疲劳试验方法
アーク溶接継手の片振り引張疲れ試験方法 Method of repeated tension
fatigue testing for fusion welded joints
JIS Z3122-1990 对接焊接头的弯曲试验方法
突合せ溶接継手の曲げ試験方法 Methods of bend test for butt
welded joint
JIS Z3138-1989 点焊接头疲劳试验法
スポット溶接継手の疲れ試験方法 Method of fatigue testing for
spot welded joint
JIS Z3153-1993 T型接头焊缝裂纹试验方法
Ｔ形溶接割れ試験方法 Method of T-joint weld cracking test
JIS Z3192-1999 硬钎焊接头抗拉伸及抗剪切试验方法
ろう付継手の引張及びせん断試験方法 Methods of tensile and shear
tests for brazed joint
法国接头标准(NF joint standards)
--------------------------------------------------------------------------------
编号 中文名称 英文名称
NF A48-720-1999 建筑物排水用铸铁管和配件及其接头和附件.要求、试验方法和质量保证
(Cast iron pipes and fittings, their joints
and accessories for the evacuation of water
from buildings. Requirements, test methods and
quality assurance.)
NF A48-801-2002 水管用球墨铸铁管、配件和附件及其接头.要求和试验方法 (Ductile
iron pipes, fittings, accessories and their
joints for water pipelines - Requirements and
test methods.)
NF A48-810-1995 燃气管道用球墨铸铁管、配件、附件及其接头.要求和试验方法
(Ductile iron pipes, fittings, accessories and
their joints for gas pipelines. Requirements
and test methods.)
NF A48-810/A1-1999 燃气管道用球墨铸铁管、配件、附件及其接头.要求和试验方法
(Ductile iron pipes, fittings, accessories and
their joints for gas pipelines. Requirements
and test methods.)
NF A48-820-1994 污水排放用球墨铸铁管、配件、附件及其接头.要求和试验方法
(Ductile iron pipes, fittings, accessories and
their joints for sewerage application. Requirements
and tests methods.)
NF A48-830-1983 铸制产品.有压力的饮用水聚氯乙烯管道用球墨铸铁接头 (Foundry
products. Spheroidal graphite cast iron sittings
for PVC drinking water pipes under pressure.)
NF A48-860-1981 铸造产品.承压管道用可锻铸铁管道部件.承插系列.GS快速接头.连接尺寸和连接附件
(Foundry products. Ductile cast iron piping
elements. Socket serie. GS express joint. Assembly
dimensions and joint accessories.)
NF A48-870-1981 铸造产品.承接管道用可锻铸铁管道部件.承插系列.GS标准接头.连接尺寸和连接附件
(Foundry products. Ductile cast iron piping
elements. Socket series. GS standard joint.
Assembly dimensions and joint accessories.)
NF A49-150-2003 包括人类生活用水在内的水成液的传送用非合金钢管和管接头.技术交货条件
(Non-alloy steel tubes and fittings for the
conveyance of aqueous liquids including water
for human consumption - Technical delivery conditions.)
NF A49-191-1975 钢管.毛细管焊接或焊接钎接用钢或铸铁接头.（尺寸.交货技术条件.）
(STEEL TUBES. SPIGOT OR MIXED CONNECTIONS MADE
OF STEEL OR CAST IRON FOR CAPILLARY BRAZING
OR BRAZE WELDING. DIMENSIONS. TECHNICAL DELIVERY
CONDITIONS.)
NF A49-716-1998 钢管.焊接接头镀膜配件和管的外结构. (STEEL TUBE.
EXTERNAL CONSTITUTION OF TUBE AND FITTING COATING
FOR WELDED JOINT.)
NF A72-120-1973 钢铁厂.气体管道和大直径阀.带法兰的接头（PN6） (LARGE
DIAMETER PIPES AND VALVES FOR GASEOUS FLUIDS.
FLANGE CONNECTIONS PN 6.)
NF A80-022-1999 焊接.带说明的多语种接头术语 (WELDING. MULTILINGUAL
TERMS FOR WELDED JOINTS WITH ILLUSTRATIONS.
(EUROPEAN STANDARD EN 12345).)
NF A82-104-1-2000 电阻焊接设备.电极接头,外锥度1:10.第1部分:圆锥形接头,锥度1:10
(Resistance welding equipment - Electrode adaptors,
male taper 1:10 - Part 1 : conical fixing, taper
1:10.)
NF A82-104-2-2001 电阻点焊.外锥度1:10电极接头.第2部分:端推力电极用平行柄接头
(Resistance spot welding - Electrode adaptors,
male taper 1:10 - Part 2 : parallel shank fixing
for end-thrust electrodes.)
NF A82-104-3-1992 电阻点焊.电极帽的活动接头 (Resistance
spot welding electrode caps.)
NF A84-420-1991 气焊设备和有关方法.减压阀入品接头.尺寸 (Equipment
for gas welding and allied processes. Pressure
regulators inlet connections. Dimensions.)
NF A84-444-2003 气焊设备.焊接、切割和相关工艺用乙炔复式接头系统.高压装置的安全要求
(Gas welding equipment - Acetylene manifold
systems for welding, cutting and allied processes
- Safety requirements in high-pressure devices.)
NF A87-011-1994 带有电焊条的金属电弧熔焊、气体保护金属弧焊及气焊.钢接头的制备
(Metal-arc welding with covered electrode, gas-shielded
metal-arc welding and gas welding. Joint preparations
for steel.)
NF A87-013-2-1999 焊接和相关工艺.接头的预处理.第2部分:钢的埋弧焊
(WELDING AND ALLIED PROCESSES. JOINT PREPARATION.
PART 2 : SUBMERGED ARC WELDING OF STEELS. (EUROPEAN
STANDARD EN ISO 9692-2).)
NF A87-013-3-2001 焊接和相关工艺.接头预处理的推荐方法.第3部分:铝和铝合金的金属焊条惰性气体保护焊和钨极惰性气体保护焊
(Welding and allied processes - Recommendations
for joint preparation - Part 3 : metal inert
gas welding and tungsten inert gas welding of
aluminium and its alloys.)
NF A89-057-8-2002 金属材料焊接程序规范和鉴定.焊接程序试验.第8部分:管对管-板接头的焊接
(Specification and qualification of welding
procedures for metallic materials - Welding
procedure test - Part 8 : welding of tubes to
tube-plate joints.)
NF A89-208-1987 焊接和有关技术.点焊,凸焊或缝焊搭接接头 (WELDING
AND ALLIED TECHNIQUES. SPOT,PROJECTION OR SEAM
WELDED LAP JOINTS.)
NF A89-231-1992 钢的弧焊接头.质量缺陷等级导则 (ARC-WELDED
JOINTS IN STEEL. GUIDANCE ON QUALITY LEVELS
FOR IMPERFECTIONS. (EUROPEAN STANDARD EN 25817).)
NF A89-232-1994 铝和可焊合金的弧焊接头.质量缺陷等级导则 (ARC-WELDED
JOINTS IN ALUMINIUM AND ITS WELDABLE ALLOYS.
GUIDANCE ON QUALITY LEVELS FOR IMPERFECTIONS.
(EUROPEAN STANDARD EN 30042).)
NF A89-233-1996 焊接.电子束和激光束焊接接头.缺陷的质量级别导则.第1部分:钢
(WELDING. ELECTRONS AND LASER BEAM WELDED JOINTS.
GUIDANCE ON QUALITY LEVELS FOR IMPERFECTIONS.
PART 1 : STEEL. (EUROPEAN STANDARD EN ISO 13919-1).)
NF A89-234-2001 焊接.电子和激光束焊接接头.缺陷的质量级别导则.第1部分:铝及其可焊合金
(Welding - Electron and laser beam welded joints
- Guidance on quality levels for imperfections
- Part 2 : aluminium and its weldable alloys.)
NF A89-240-1987 焊接和有关技术.电阻点焊、凸焊或缝焊搭接接头.带解释的缺陷分类
(WELDING AND ALLIED PROCESSES. RESISTANCE SPOT,PROJECTION
AND SEAM WELDED LAP JOINTS. CLASSIFICATION OF
DEFECTS WITH EXPLANATORY COMMENTS.)
NF A89-430-2000 钎焊.钎焊接头的无损检验 (Brazing - Non-destructive
examination of brazed joints.)
NF A89-510-1997 焊缝的无损检验.焊接接头的X射线照相检验 (Non-destructive
examination of welds. Radiographic examination
of welded joints.)
NF A89-510/A1-2003 焊接无损检验.焊接接头射线照相检验 (Non-destructive
examination of welds - Radiographic examination
of welded joints.)
NF A89-511-1998 焊缝的无损检验.焊接接头的X射线照相检验.验收等级 (Non-destructive
examination of welds. Radiographic examination
of welded joints. Acceptance levels.)
NF A89-511/A1-2003 焊缝的无损检验.焊接接头的X射线照相检验.验收水平
(Non-destructive examination of welds - Radiographic
examination of welded joints - Acceptance levels.)
NF A89-520-1997 焊缝的无损检验.焊接接头的超声波检验 (Non destructive
examination of welds. Ultrasonic examination
of welded joints.)
NF A89-520/A1-2002 焊缝的无损检验.焊接接头的超声波检验 (Non-destructive
testing of welds - Ultrasonic testing of welded
joints.)
NF A89-521-1997 焊缝的无损检验.焊接接头的超声波检验.验收等级 (Non
destructive examination of welds. Ultrasonic
examination of welded joints. Acceptance levels.)
NF A89-521/A1-2002 焊缝的无损检验.焊接接头的超声波检验.验收等级 (Non-destructive
testing of welds - Ultrasonic testing of welded
joints - Acceptance levels.)
NF A89-810-1-1999 热塑性半成品的焊接接头试验.第1部分:弯曲试验. (Testing
of welded joints of thermoplastics semi-finished
products - Part 1 : bend test.)
NF A89-810-3-2000 热塑性半成品的焊接接头试验.第3部分:拉伸蠕变试验.
(Testing of welded joints of thermoplastics
semi-finished products - Part 3 : tensile creep
test.)
NF A89-810-4-2002 热塑性半成品的焊接接头试验.第4部分:剥离试验 (Testing
of welded joints of thermoplastics semi-finished
products - Part 4 : peel test.)
NF A89-810-5-2000 热塑半成品焊接接头的试验.第5部分:宏观检验 (Testing
of welded joints of thermoplastics semi-finished
products - Part 5 : macroscopic examination.)
NF A89-810-7-2003 热塑性半成品焊接接头的试验.第7部分:腰形试验样品的抗拉试验
(Testing of welded joints of thermoplastics
semi-finished products - Part 7 : tensile test
with waisted test specimens.)
NF A89-810-8-2002 热塑性半成品的焊接接头试验.第8部分:要求 (Testing
of welded joints of thermoplastics semi-finished
products - Part 8 : requirements.)
NF B34-001-1976 玻璃制仪器、管路及接头.硼硅3.3玻璃的特性 (Glass
plant, pipeline and fittings. Properties of
borosilicate glass 3.3.)
NF B34-002-1976 玻璃制仪器、管路及接头.试验、操作和使用的一般规则 (Glass
plant, pipeline and fittings. General rules
for testing, handling and use.)
NF B34-003-1999 玻璃制仪器、管路及接头.标称内径15-1000mm管与管接头.兼容性与互换性
(Glass plant, pipeline and fittings. Pipeline
and fittings DN 15 to DN 1000. Compatibility
and interchangeability.)
NF B35-008-1974 实验室用玻璃器皿.锥形瓶和带有磨光接头的有颈锥形瓶 (LABORATORY
GLASSWARE. CONICAL FLASKS. CONICAL FLASKS WITH
CONICAL GROUND GLASS JOINT.)
NF B35-012-1972 实验室用玻璃器皿.带互换磨光元件的球形接头 (INTERCHANGEABLE
SPHERICAL GROUND JOINTS.)
NF B35-013-1983 实验室用玻璃器皿.带互换磨光锥形接头 (Laboratory
glassware. Interchangeable conical ground joints.)
NF B35-022-1977 实验室用玻璃器皿.蒸馏器配件.适配器.转接器.接头 (LABORATORY
GLASSWARE. COMPONENTS OF DISTILLATION EQUIPEMENT.
ADAPTATORS-EXTENSIONS-UNIONS.)
NF C20-131-1974 铝导线用带导电镀层的有铝片或铜片的接头.规则和尺寸 (LUGS
WITH COPPER OR ALUMINIUM FLATS AND WITH CONDUCTING
COATING FOR ALUMINIUM CONDUCTORS. REQUIREMENTS
AND DIMENSIONS.)
NF C46-512-1999 工业处理控制阀.第3-3部分:尺寸.对焊接的头尾相接尺寸.两接头球型直接式控制阀(欧洲标准EN
60534-3-3) (Industrial-process control valves.
Part 3-3 : dimensions. End-to-end dimensions
for buttweld, two-way, globe-type, straight
pattern control valves.)
NF C52-152-1969 变压器.带凸缘的滑轮支架叉形接头和锁定装置 (TRANSFORMERS.
DIMENSIONS OF TRAVELLING WHEELS AND ASSOCIATED
LOCKING DEVICES.)
NF C52-152M1-1970 变压器.带凸缘的滑轮支架叉形接头和锁定装置 (TRANSFORMERS
DIMENSIONS OF TRAVELLING WHEELS AND ASSOCIATED
LOCKING DEVICES.)
NF C64-021-1991 交流电用高压设备.管线用的接头 (CONNECTORS
FOR TUBES.)
NF C66-495-1988 架空线路用绝缘子和器材.绝缘子链元件的球状头和球槽接头.特性尺寸
(Insulators and fittings for overhead lines.
Dimensions of ball and socket couplings of string
insulator units.)
NF C66-496-1988 架空线路用绝缘子和器材.架空线路绝缘体和器材.绝缘子链元件的球状接头和球槽头锁定装置.第1部分：尺寸和一
(Isolators and fittings for overhead lines.
Locking devices for ball and socket couplings
of string insulator units.)
NF C66-800-1978 架空线路用绝缘子和器材.架空线路连接件.接头，分接头和端点连接件
(INSULATORS AND FITTINGS FOR OVERHEAD LINES.
CONNECTION JOINTS FOR OVERHEAD LINES. JUNCTION
JOINTS,TEE JOINTS,AND END-JOINTS.)
NF C74-347-1993 低型接头式可植入心脏起搏器(EN 50077) (Low-profile
connector implantable cardiac pacemakers.)
NF C93-421-1983 电子元件.连接元件.ＨＥ７型节距为２?５４mm单面印制电路板用插入式多触点接头
(Electronic components. Connecting devices.
Multicontact edge socket and board mounted connectors
for single clad printed boards with 2,54 mm
spacing. Type he 7. General requirements.)
NF C93-422-1977 电子元件.连接元件.多触点圆柱状接头.一般规定 (Electronic
components. Connecting devices. Circular multipole
connectors.)
NF C93-423-1982 电子元件.连接元件.ＨＥ９型节距为２?５４mm双面印刷电路板用插入式多触点接头.特殊规范汇编
(Electronic components. Connecting devices.
Multicontact edge socket and board mounted connectors
for double clad printed boards with 2,54 mm
spacing. Type HE 9. General requirements.)
NF C93-424-1982 电子元件.连接元件.Ａ型插入式印刷电路板多触点接头及其相应的ＨＥ８型节距为１?２７mm的插座.一般规定
(Electronic components. Connecting devices.
Board mounted printed circuits connectors with
contact and termination spacing of 1,27 mm.
Type HE 8. General requirements.)
NF C93-425-1981 电子元件.连接元件.带外壳的支架和板条的多触点接头.一般要求
(ELECTRONIC COMPONENTS. CONNECTING DEVICES.
MULTIPOLE CONNECTORS WITH SHELL FOR RACKS AND
PANELS. GENERAL REQUIREMENTS.)
NF C93-426-1977 连接元件.模制件的矩形多触点接头.一般规定 (ELECTRONIC
COMPONENTS. CONNECTING DEVICES. MULTIPOLE RECTANGULAR
CONNECTORS WITHOUT SHELL. GENERAL REQUIREMENTS.)
NF C93-428-1981 电子元件. 连接元件.与纱包电缆自动剥离间距为１?２７mm的Ａ型多触点插入式接头及其垂直距离为２?５４mm
(ELECTRONIC COMPONENTS. CONNECTING DEVICES.
INSULATION DISPLACEMENT CONNECTORS. TYPE HE
10. GENERAL REQUIREMENTS.)
NF C93-429-1986 质量保证的电子元件.连接元件.间距为２?５４mm的印刷电路板用插入式多触点接头.ＨＥ１１型.一般规定
(Electronic components under quality assessment.
Connecting devices. Multicontact board mounted
connectors for printed boards with 2,24 mm spacing.
Type he 11. General requirements.)
NF C93-462-1981 电子设备元件.终端连接系统.可移动蠕变式模件.接头.一般要求
(Components for electronic equipment. Terminal
junction system. Modules with removable crimp-type.
Contacts. General requirements.)
NF C93-557-2001 RF接头、接头电缆组件和电缆.互调程度测量 (RF connectors,
connector cable assemblies and cables - Intermodulation
level measurement.)
NF C93-561-1981 电子元件.螺钉锁定的小型同轴接头.一般规定 (Components
for electronic equipment. Miniature coaxial
connectors with screw coupling. General requirements.)
NF C93-562-1981 电子元件.弹簧栓耦接的小型同轴接头.一般规定 (Components
for electronic equipment. Miniature coaxial
connectors with snap-on coupling. General requirements.)
NF C93-564-1981 电子元件.接线柱锁定射频用同轴接头（ＫＢＮ系列） (Electronic
components. Miniature coaxial connectors with
bayonet coupling (kbn series). General requirements.)
NF C93-566-1981 电子元件.螺钉锁定射频用同轴接头（ＫＮ系列）.一般规定
(ELECTRONIC COMPONENTS. RF COAXIAL CONNECTORS
WITH SCREW COUPLING (TYPE KN). GENERAL REQUIREMENTS.)
NF C93-570-1986 电子元件.射频同轴接头.１?６－５?５系列.７５Ω阻抗.ＫＴＢ型
(RF COAXIAL CONNECTORS 1,6-5,6 SERIE CHARACTERISTIC
IMPEDANCE 75 OHMS. TYPE KTB.)
NF C93-571-1986 电子元件.射频同轴接头.１?０－２?３系列.ＫＴＡ型 (RF
COAXIAL CONNECTORS 1,0-2,3 SERIE TYPE KTA.)
NF C93-618-3-2002 质量评定的石英晶体装置.第3部分:标准外形线和引线接头
(Quartz crystal units for assessed quality -
Part 3 : standard outlines and lead connections.)
NF C93-711-5-6-2003 印制板和印制板组件.设计和使用.第5-6部分:附件(结合区/接头)考虑.四面带有J形引线的片状载体
(Printed boards and printed board assemblies
- Design and use - Part 5-6 : attachment (land/joint)
considerations - Chip carriers with J-leads
on four sides.)
NF C93-867-2-1-2002 光纤通信系统中使用的接头组件和互连元件.产品规范.第2-1部分:端接在IEC
60793-2的B1类单模纤维上的FC-PC型 (Connector sets and
interconnect components to be used in optical
fibre communication systems - Product specifications
- Part 2-1 : type FC-PC terminated on IEC 60793-2
category B1 singlemode fibre.)
NF C93-867-3-1-2002 光纤通信系统中使用的接头组件和互连元件.产品规范.第3-1部分:端接在IEC
60793-2的A1a类和A1b类多模纤维上 (Connector sets and Interconnect
components to be used in optical fibre communication
systems - Product specifications - Part 3-1
: type SG terminated on IEC 60793-2 category
A1a and A1b multimode fibr)
NF C93-909-1-1-2001 光纤互连装置和无源元件性能标准.第1-1部分:总则和指南.互连装置(接头)
(Fibre optic interconnecting devices and passive
components peformance standard - Part 1-1 :
general and guidance - Interconnecting devices
(connectors).)
NF D36-105-1976 燃气洗衣机内部连接用带机械接头的软管 (FLEXIBLE
HOSE WITH MECHANICAL CONNECTORS FOR JOINTS INSIDE
GAS-POWERED WASHING MACHINES.)
NF D36-107-1994 家政学.家用管道煤气装置连接用的带机械接头的11号或12号聚酰胺基未增强软管
(Household economy. Flexible piping based on
polyamide 11 or 12 for the external connection
of domestic appliances using gaseous fuels distributed
by networks.)
NF D36-108-1983 家用灶具装配用挠性金属管内接头 (INTERNAL CONNECTION
OF DOMESTIC COOKING APPLIANCES BY MEANS OF FLEXIBLE
METAL HOSES.)
NF D36-210-2001 建筑物燃气管道工程的螺纹接头再密封的方法 (Means
for resealing threaded joints of gas pipework
in buildings.)
NF E04-202-2-1996 工业加工用管道、管道元件和仪器.图形符号表示.第2部分:管道和接头
(Pipelines, pipe components and apparatus for
industrial processes. Symbolic representation.
Part 2 : pipelines and junctions.)
NF E22-601-1985 联轴节.工业万向接头传动.定义.特性 (Couplings.
Industrial cardan shaft. Definition. Characteristics.)
NF E22-603-1985 联轴节.工业万向接头传动.验收 (Couplings.
Industrial cardan shaft. Acceptance.)
NF E22-604-1985 联轴节.工业万向接头传动.用法兰盘固定 (Couplings.
Industrial cardan shaft. Flange mounting.)
NF E29-032-1985 工业管道.钢制构件.对焊接头.准备 (Industrial
pipework. Steel components. Butt welding ends.
Preparation.)
NF E29-042-1-2000 法兰及其接头.螺栓连接.第1部分:螺栓连接的选择 (Flanges
and their joints - Bolting - Part 1 : selection
of bolting.)
NF E29-551-1939 钢制气体螺距的连接管.双接头 (STEEL CONNECTIONS
WITH GAS THREAD. DOUBLE NIPPLES.)
NF E29-692-1-2001 气瓶.微电子工业用气瓶阀接头.第1部分:输出口接头
(Gas cylinders - Gas cylinder valve connections
for use in the micro-electronics industry -
Part 1 : outlet connections.)
NF E29-692-2-2001 气瓶.微电子工业用气瓶阀接头.第2部分:气瓶阀接头的规范和型式试验
(Gas cylinders - Gas cylinder valve connections
for use in the microelectronics industry - Part
2 : specification and type testing for valve
to cylinder connections.)
NF E29-901-1-2001 法兰及其接头.分级标识法兰用垫圈.第1部分:有或无插件的非金属平垫圈
(Flanges and their joints - Gaskets for Class-designated
flanges - Part 1 : non-metallic flat gaskets
with or without inserts.)
NF E29-901-2-2001 法兰及其接头.分级标识法兰用垫圈.第2部分:与钢法兰一起使用的螺旋形绕制垫圈
(Flanges and their joints - Gaskets for Class-designated
flanges - Part 2 : spiral wound gaskets for
use with steel flanges.)
NF E29-901-3-2001 法兰及其接头.分级标识法兰用垫圈.第3部分:非金属PTFE包封垫圈
(Flanges and their joints - Gaskets for Class-designated
flanges - Part 3 : non-metallic PTFE envelope
gaskets.)
NF E29-901-4-2001 法兰及其接头.分级标识法兰用垫圈.第4部分:与钢法兰一起使用的波纹形、平的或带槽的金属和嵌条金属垫圈
(Flanges and their joints - Gaskets for Class-designated
flanges - Part 4 : corrugated, flat or grooved
metallic and filled metallic gaskets for use
with steel flanges.)
NF E29-901-5-2001 法兰及其接头.分级标识法兰用垫圈.第5部分:与钢法兰一起使用的金属环接垫圈
(Flanges and their joints - Gaskets for Class-designated
flanges - Part 5 : metallic ring-joint gaskets
for use with steel flanges.)
NF E29-902-1-1997 法兰及其接头.PN指定法兰用垫圈的尺寸.第1部分:有或无衬套的非金属平垫圈
(Flanges and their joints. Dimensions of gaskets
for PN-designated flanges. Part 1 : non-metallic
flat gaskets with or without inserts.)
NF E29-902-2-1997 法兰及其接头.PN指定法兰用垫圈的尺寸.第2部分:与钢法兰配套使用的螺旋绕线垫圈
(Flanges and their joints. Dimensions of gaskets
for PN-designated flanges. Part 2 : spiral wound
gaskets for use with steel flanges.)
NF E29-902-3-1997 法兰及其接头.PN指定法兰用垫圈的尺寸.第3部分:非金属聚四氟乙烯封装垫圈
(Flanges and their joints. Dimensions of gaskets
for PN-designated flanges. Part 3 : non-metallic
PTFE envelope gaskets.)
NF E29-902-4-1997 法兰及其接头.PN指定法兰用垫圈的尺寸.第4部分:与钢法兰配套使用的波纹形、平的或开槽金属和填充金属垫圈
(Flanges and their joints. Dimensions of gaskets
for PN-designated flanges. Part 4 : corrugated,
flat or grooved metallic and filled metallic
gaskets for use with steel flanges.)
NF E39-012-2003 区域供暖管道.直埋式热水供应网用预隔热连接的管道系统.聚氨酯隔热和聚乙烯外护层的入户钢管用接头组件
(District heating pipes - Preinsulated bonded
pipe systems for directly buried hot water networks
- Fitting assemblies for steel service pipes,
polyurethane thermal insulation and outer casing
of polye)
NF E48-051-1992 液压传动.进气口上的步进管螺纹接头.接头尺寸 (Hydraulic
fluid power. Pipe threaded connections for supply
ports. Connecting dimensions.)
NF E48-064-1998 液压传动和一般用金属导管的连接.第1部分:24喇叭形压合接头
(Metallic tube connections for fluid power and
general use. Part 1 : 24 degrees compression
fittings.)
NF E49-090-2-2003 气压传动.18mm和26mm五气口方向控制阀.第2部分:带光学电接头的安装面
(Pneumatic fluid power - Five-port directional
control valves, sizes 18 mm and 26 mm - Part
2 : mounting interfaces with optional electrical
connector.)
NF E62-541-1984 工具自动变换工具用的连接锥.锥体Ｎ度４０，４５，５０的７／２４锥度工具柄的拉制接头
(Tool shank taper rate 7/24 for automatic tool
changer. Retention knobs for shanks no 40, 45,
50.)
NF E62-542-1990 自动更换刀具用的7/24锥度刀柄.NO.30锥体及相应的拉伸接头.尺寸
(TOOL SHANKS WITH 7/24 TAPERS FOR AUTOMATIC
TOOL CHANGERS. SHANKS NO 30 AND CORRESPONDING
RETENTION KNOBS. DIMENSIONS.)
NF E86-400-1-2001 法兰和接头.衬垫环形法兰连接的设计规则.第1部分:计算方法
(Flanges and their joints - Design rules for
gasketed circular flange connections - Part
1 : calculation method.)
NF F00-364-1991 通用铁路设备.与电引线有关的产品.电线接头的插片尺寸为:2.8×0.5,5×0.8,6.3×0.8mm
(RAILWAY MATERIAL IN GENERAL. PRODUCTS FOR ELECTRICAL
CONNECTIONS. 2,8 X 0,5. 5 X 0,8. 6,3 X 0,8 MM.)
NF F01-082-1968 铁路车辆.管路. 软管接头（非金属） (RAILWAY
TRANSPORT EQUIPMENT. PIPEWORK. FIXING OF NON-METALLIC
FLEXIBLE PIPES.)
NF F01-082M-1970 铁路车辆.管路.软管接头(非金属) ()
NF F01-810-1990 铁路车辆.非合金钢或低合金钢电弧焊和电阻焊接头.设计与施工规则
(RAILWAY ROLLING STOCK. ARC AND RESISTANCE WELDED
JOINTS OF UNALLOYED OR LOW ALLOYED STEELS. RULES
FOR CONCEPTION AND REALIZATION.)
NF F01-812-1-1990 铁路车辆.钢的电弧和电阻焊接接头.第1部分:对接焊和角接接头中缺陷验收准则
(RAILWAY ROLLING STOCK. ART AND RESISTANCE WELDED
JOINTS OF STEELS. PART 1 : ACCEPTANCE CRITERIA
FOR DEFECTS IN WELDED BUTT AND CORNER JOINTS.)
NF F01-820-1992 铁路车辆.车身用铝合金焊接接头(焊缝) (RAILWAY
ROLLING STOCK. WELDED JOINTS OF PRODUCTS IN
ALUMINIUM ALLOY FOR BODYWORK. CHARACTERIZATION.)
NF F11-013-1984 铁路车辆.压缩空气制动. ２５mm自动制动装置连接头 (Railway
rolling stock. Compressed-air brake. Coupling
head for 25 mm automatic brake pipe.)
NF F11-014-1970 铁路车辆.压缩空气制动装置. 直通式自动制动连接头 (RAILWAY
TRANSPORT EQUIPMENT. AIR BRAKE. DIRECT BRAKE
COUPLING HEAD.)
NF F11-015-1984 铁路车辆. 空气导管. ２５mm主要导管的连接头 (Railway
rolling stock. Air pipes. Coupling head for
25 mm main brake pipe.)
NF F11-069-1988 铁路车辆.气动部件检验设备的用接头 (ROLLING STOCK.
CONNECTIONS FOR PNEUMATIC-GEAR CONTROL EQUIPMENT.)
NF F11-101-1994 铁路车辆.有凸缘的气动要装置的接头和密封接触面 (Railway
rolling stock. Connecting and airtight interfaces
for flanged pneumatic apparatuses.)
NF F20-028-1950 通用铁路设备.气炉堵. 接头 (RAILWAY MATERIAL
IN GENERAL. BUFFER SEALS.)
NF F24-005-1968 铁路车辆.轻型器材.管道系统.摆动式管接头 (RAILWAY
TRANSPORT EQUIPMENT. WEIGHT-SAVING EQUIPMENT.
PIPEWORK. SWIVEL CONNECTORS.)
NF F31-011-1983 铁路车辆.非饮用水贮水箱的注水接头 (Rolling stock.
Connecting pipe for filling non-drinking water
tanks.)
NF F36-001-1975 铁路车辆.工业货车. 标称直径为５０的通用“ＡＩＲ“ 调节接头
(RAILWAY TRANSPORT EQUIPMENT. INDUSTRIAL WAGONS.
STANDARD 50 MM AIR COUPLING.)
NF F36-002-1974 铁路运输设备.工业货车.50MM气体导径管接头 (RAILWAY
TRANSPORT EQUIPMENT. INDUSTRIAL WAGONS. 50 MM
AIR ADAPTOR COUPLING.)
NF F36-003-1977 铁路车辆.工业货车. 标称直径为５０的通用“ＡＩＲ“ 接头的安装
(RAILWAY TRANSPORT EQUIPMENT. INDUSTRIAL WAGONS.
PLUG FOR STANDARD 50 MM AIR COUPLING.)
NF F36-004-1977 铁路车辆.工业货车. ＧＵＩＬＬＥＭＩＮ系统对称快速半接头的安装
(RAILWAY TRANSPORT EQUIPMENT. INDUSTRIAL WAGONS.
ALTERNATIVES FOR FITTING STANDARD 50 MM AIR
COUPLING.)
NF F38-001-1975 铁路运输设备.采用最大压力为2.5bar排空的散装粉状产品运输用气动排空车.粉导管用统一接头
(RAILWAY TRANSPORT EQUIPMENT. WAGONS WITH PNEUMATIC
DISCHARGE,FOR CARRYING POWDER GOODS IN BULK
WITH DISCHARGE AT MAXIMUM OPERATING PRESSURE
OF 2.5 BAR. STANDARD AIR PIPE CONNECTION.)
NF F38-002-1971 铁路运输设备.采用最大压力为2.5bar排空的散粉状产品运输用气动排空车.散粉导管用统一接头
(RAILWAY TRANSPORT EQUIPMENT. WAGONS WITH PNEUMATIC
DISCHARGE FOR CARRYING POWDER GOODS IN BULK.
DISCHARGE AT MAXIMUM SERVICE PRESSURE OF 2.5
BARS.)
NF F38-002M-1976 铁路运输设备.采用最大压力为2.5bar的散装粉状产品运输用气动排空车.排空粉导管用统一接头
()
NF F61-011-1989 铁路车辆.电气连接用铜螺旋旋入接头.紧固扭矩G.纺织和皮革
(Railway rolling stock. Screwed joint for electrical
copper connections driving torque.)
NF F61-021-1990 铁路车辆.用于铝制导电引线的螺纹接头.上紧力矩 (RAILWAY
ROLLING STOCK. SCREWED JOINT FOR ELECTRICAL
ALUMINIUM CONNCECTIONS DRIVING TORQUE.)
NF G07-310-1981 纺织.缝纫线试验.接头拉断力的测定方法 (TEXTILES.
SEWING THREAD TESTS. METHOD OF DETERMINATION
FO BREAKING LOAD OF SNARLING.)
NF G38-116-1996 土工织物.用大宽度法测定接头/接缝处的拉伸试验 (GEOTEXTILES.
TENSILE TEST FOR JOINTS/SEAMS BY WIDE/WIDTH
METHOD. (EUROPEAN STANDARD EN ISO 10321).)
NF H50-010-2-2000 货架接头试验方法.第2部分:货架钉子和钩环头拉伸抗性和回缩特性的测定
(Methods of test for pallet joints - Part 2
: determination of withdrawal and head pull-through
resistance of pallet nails and staples.)
NF J33-372-1987 游艇.不锈钢缆用拉紧装置和活动缆的固定接头.尺寸 (Small
craft. Rigging screws for stainless steel wire
rope. Principal dimensions for forks, connection
pins and eye-holes.)
NF J43-805-1-1997 造船和海上建筑物.饮用水箱注水接头.第1部分:总要求
(Shipbuilding and marine structures. Filling
connection for drinking water tanks. Part 1
: general requirements.)
NF J43-805-2-1997 造船和海洋建筑物.饮水罐用装水接头.第2部分:组件
(Shipbuilding and marine structures. Filling
connection for drinking water tanks. Part 2
: components.)
NF J45-910-1949 造船工业.传话管.接头 (SHIPBUILDING. VOICE-PIPES.
JOINTS.)
NF J82-214-1967 造船工业.管道.接头.分类和应用 (INLAND NAVIGATION.
PIPING. SEALING RINGS. CLASSIFICATION AND USE.)
NF L20-026-1995 航空航天系列.插销.尺寸和接头选择.设计标准 (Aerospace
series. Spigots. Dimensions and fit selection.
Design standard.)
NF L31-512-1966 球面轴承接头.(RECH.). (SPHERICAL BEARING
JOINTS. (RECH.).)
NF L34-430-1954 机载仪表.挠性操纵接头 (FLIGHT DECK INSTRUMENTS,FLEXIBLE
CONTROL CONNECTIONS. (RECH.).)
NF L35-140-1966 操纵连杆用叉形接头.叉尾柄带螺纹的式样.(RECH.)
(FORK JOINTS FOR CONTROL LINKAGE. MODEL WITH
THREADED END. (RECH.).)
NF L35-150-1974 滚珠球形接头.无纵向槽的长螺纹杆.尺寸和负荷 (ROD-ENDS
WITH SELF-ALIGNING BALL BEARINGS. LONG THREADED
SHANK WITHOUT KEYWAY. DIMENSIONS AND LOADS.)
NF L35-151-1974 滚珠球形接头.有纵向槽的长螺纹杆.尺寸和负荷 (ROD-ENDS
WITH SELF-ALIGNING BALL BEARINGS. LONG THREADED
SHANK AND KEYWAY. DIMENSIONS AND LOADS.)
NF L35-170-1974 有自润滑装置的球形接头.无纵向槽的长螺纹杆.尺寸和负荷
(ROD-ENDS WITH SELF-LUBRICATING SPHERICAL BEARING
- LONG THREADED SHANK WITHOUT KEYWAY - DIMENSIONS
AND LOADS.)
NF L35-171-1974 有自润滑装置的球形接头有纵向槽的长螺纹杆.尺寸和负荷 (ROD-ENDS
WITH SELF-LUBRICATING SPHERICAL BEARING - LONG
THREADED SHANK AND KEYWAY - DIMENSIONS AND LOADS.)
NF L35-450-1954 带螺纹尾柄型传动球形接头 (BALL JOINTS FOR
CONTROLS,THREADED END. (RECH.).)
NF L35-451-1967 小型控制机构用带螺纹尾柄的球形接头 (BALL JOINTS
FOR SMALL CONTROLS,THREADED END (RECH.).)
NF L35-452-1980 小型传动装置用带颈的螺纹端头的球形接头 (BALL JOINTS
FOR SMALL CONTROLS. THREADED END AND UNDERCUT.)
NF L36-121-1966 缆绳咬合带孔接头.(RECH.) (EYE ENDS FOR
SWAGING ON CABLE. (RECH.).)
NF L36-122-1966 缆绳咬合叉形接头.(RECH.) (FORK ENDS
FOR SWAGING ON CABLE. (RECH.).)
NF L36-123-1966 连接缆绳和链的链接头.(RECH.) (CRIMPING
FERRULES FOR ATTACHING CABLES TO CHAINS. (RECH.).)
NF L36-124-1966 缆绳咬合螺纹接头.(RECH.) (SCREWED ENDS
FOR SWAGING ON CABLE. (RECH.).)
NF L36-128-1966 缆绳咬合球形接头.(RECH.) (BALL ENDS
FOR SWAGING ON CABLE. (RECH.).)
NF L36-135-1971 拉紧螺杆叉形接头 (SCREWED END FORKS.)
NF L36-137-1971 转动拉紧螺杆叉形接头.技术规范 (SCREWED END
FORKS FOR BALL BEARINGS.)
NF L36-139-1971 嵌入缆绳的拉紧螺杆接头 (SCREWED ENDS FOR
SWAGING ON CABLE.)
NF L36-141-1971 嵌入缆绳的带孔接头 (EYE ENDS FOR SWAGING
ON CABLE.)
NF L36-142-1971 嵌入缆绳的叉形接头 (FORK ENDS FOR SWAGING
ON CABLE.)
NF L36-143-1971 嵌入缆绳的转动叉形接头 (FORK ENDS FOR BALL
BEARINGS FOR SWAGING ON CABLE.)
NF L36-144-1971 嵌入缆绳的球形接头 (BALL ENDS FOR SWAGING
ON CABLE.)
NF L36-202-1989 航空和航天系列.钢制抗腐蚀拉紧螺杆用带眼接头.尺寸和负载
(Aerospace series. Eye-ends, threaded, control
cable in corrosion resisting steel. Dimensions
and loads.)
NF L36-203-1989 航空和航天系列.钢制抗腐蚀拉紧螺杆用带眼接头.尺寸和负载
(Aerospace series. Fork-ends, threaded, control
cable in corrosion resisting steel. Dimensions
and loads.)
NF L36-204-1989 航空和航天系列.钢制抗腐蚀轴承用拉紧螺杆叉形接头.尺寸和负载
(Aerospace series. Fork-ends, threaded, control
cable for rolling bearings in corrosion resisting
steel. Dimensions and loads.)
NF L36-205-1989 航空和航天系列.嵌入操纵缆索的钢制抗腐蚀拉紧螺杆接头.尺寸和负载
(AEROSPACE SERIES. STUD-ENDS,IN CORROSION RESISTING
STEEL SWAGED ON TYPE,CONTROL CALBLE. DIMENSIONS
AND LOADS. (EUROPEAN STANDARD EN 2357).)
NF L36-206-1989 航空和航天系列.嵌入操纵缆索的钢制抗腐蚀带眼接头.尺寸和负载
(AEROSPACE SERIES. EYE-ENDS,IN CORROSION RESISTING
STEEL SWAGED ON TYPE,CONTROL CABLE. DIMENSIONS
AND LOADS. (EUROPEAN STANDARD EN 2358).)
NF L36-207-1989 航空和航天系列.嵌入操纵缆索的钢制抗腐蚀叉形接头.尺寸和负载
(AEROSPACE SERIES. FORK-ENDS,IN CORROSION RESISTING
STEEL SWAGED ON TYPE,CONTROL CABLE. DIMENSIONS
AND LOADS. (EUROPEAN STANDARD EN 2359).)
NF L36-208-1989 航空和航天系列.抗嵌入操纵缆索的钢制抗腐蚀球体端面接头.尺寸和负载
(AEROSPACE SERIES. FORK-ENDS,FOR ROLLING BEARINGS
IN CORROSION RESISTING STEEL SWAGED ON TYPE,CONTROL
CABLE. DIMENSIONS AND LOADS. (EUROPEAN STANDARD
EN 2360).)
NF L36-209-1989 航空和航天系列.嵌入操纵缆索的钢制抗腐蚀球端面接头.尺寸和负载
(AEROSPACE SERIES. BALL-ENDS,DOUBLE SHANK IN
CORROSION RESISTING STEEL SWAGED ON TYPE,CONTROL
CABLE. DIMENSIONS AND LOADS. (EUROPEAN STANDARD
EN 2361).)
NF L36-210-1989 航空和航天系列.嵌入操纵缆索的钢制抗腐蚀球面接头.尺寸和负载
(AEROSPACE SERIES. BALL-ENDS,IN CORROSION RESISTING
STEEL SWAGED ON TYPE,CONTROL CABLE. DIMENSIONS
AND LOADS. (EUROPEAN STANDARD EN 2362).)
NF L36-211-1989 航空系列.操纵缆索的拉紧螺杆接头.尺寸 (AEROSPACE
SERIES. LOCKING CLIPS FOR TURNBUCKLES OF CONTROL
CABLES. DIMENSIONS. (EUROPEAN STANDARD EN 2363).)
NF L36-222-1991 航空和航天系列.带自润滑油封和螺纹安装杆的球形可调接头:螺纹直径1.5.尺寸和负荷.(欧洲标准EN
2790) (AEROSPACE SERIES. ROD ENDS,ADJUSTABLE,SELF-ALIGNING
PLAIN BEARING WITH SELF-LUBRICATING LINER AND
THREADED SHANK WITH ENGAGEMENT : 1,5 THREAD
DIAMETER. DIMENSIONS AND LOADS. (EUROPEAN STANDARD
EN 2790).)
NF L36-223-1991 航空和航天系列.带自润滑油封和螺纹安装杆的单包边可调接头:螺纹直径1.5.尺寸和负荷.(欧洲标准EN
2791) (AEROSPACE SERIES. ROD ENDS,ADJUSTABLE,SINGLE
FORK AND THREADED SHANK WITH ENGAGEMENT : 1,5
X THREAD DIAMETER. DIMENSIONS AND LOADS. (EUROPEAN
STANDARD EN 2791).)
NF L36-224-1991 航空和航天系列.带自润滑油封和螺纹安装杆的双包边可调接头.螺纹直径1.5.尺寸和负荷.(欧洲标准EN
2792) (AEROSPACE SERIES. ROD ENDS,ADJUSTABLE,DOUBLE
FORK AND THREADED SHANK WITH ENGAGEMENT :1,5
X THREAD DIAMETER. DIMENSIONS AND LOADS. (EUROPEAN
STANDARD EN 2792).)
NF L40-100-1966 飞行器的液体装置.管道接头基本尺寸 (INSTALLATION
OF FLUIDS ABOARD AIRCRAFT. BASIC DIMENSIONS
OF HOSE CONNECTIONS.)
NF L40-101-1974 轴向密封接头.ＩＳＯ米制阴螺纹剖面的凹端和BNAE公差
(CONNECTORS,AXIAL SEALING. INTERNAL THREAD BOSSES,ISO
METRIC THREAD PROFILE AND B.N.A.E. TOLERANCES.)
NF L40-102-1966 飞机的液体装置.国际单位米制螺纹凸端的轴向密封接头 (AIRCRAFT
FLUID INSTALLATIONS. CONNECTORS,AXIAL SEALING,MALE
THREAD FITTINGS. SIM THREAD. (RECH.).)
NF L40-103-1974 轴向密封接头.ISO米制螺纹剖面的凸端和BNAE公差 (CONNECTORS,AXIAL
SEALING. MALE THREAD FITTINGS,ISO METRIC THREAD
PROFILE AND B.N.A.E. TOLERANCES.)
NF L40-104-1973 轴向密封接头.ISO米制螺纹剖面的凸端和ISO米制螺纹公差
(CONNECTORS,AXIAL SEALING. MALE THREAD FITTINGS,ISO
METRIC THREAD PROFILE AND TOLERANCES.)
NF L40-105-1973 轴向密封接头.ISO 米制阴螺纹剖面凸端和ISO米制螺纹公差
(CONNECTORS,AXIAL SEALING. INTERNAL THREAD BOSSES,ISO
METRIC THREAD PROFILE AND TOLERANCES.)
NF L40-112-1987 航空和航天.经向密封接头.阳螺纹剖面和ISO 米制螺纹公差.尺寸
(Aerospace fitting joint assembly, radial sealing.
Male thread fittings. ISO metric thread profile
and tolerances. Dimensions.)
NF L40-113-1987 航空和航天.经向密封接头.阴螺纹剖面和ISO 米制螺纹公差.尺寸
(Aerospace fitting joint assembly, radial sealing.
Internal thread bosses. ISO metric thread profile
and tolerances. Dimensions.)
NF L40-114-1987 航空和航天.径向密封接头.环形接头.尺寸 (Aerospace
fitting joint assembly, radial sealing. O-rings.
Dimensions.)
NF L40-120-1983 液压系统.米制接头的接触面 (FLUID SYSTEMS.
INTERFACE OF METRIC COUPLINGS.)
NF L41-210-1983 液体系统.软管、管道和接头的脉冲试验 (Fluid systems.
Impulse testing of hose, tubing and fittings.)
NF L41-212-1983 液压系统.管子和接头的热冲击试验 (FLUID SYSTEMS.
THERMAL SHOCK TESTING OF PIPING AND FITTINGS.)
NF L41-230-1985 飞行器.液压管路组装和接头.旋转弯曲试验 (AIRCRAFT.
HYDRAULIC TUBING JOINTS AND FITTINGS. ROTARY
FLEXURE TEST.)
NF L43-110-1966 飞行器的液体装置.软管用插入接头 (AIRCRAFT FLUID
INSTALLATIONS. PLUG-IN UNIONS FOR FLEXIBLE HOSES.)
NF L43-210-1973 环形接头（RT）、一般互换条件、ISO 米制螺纹剖面和BNAE公差
(CYLINDRICAL UNION. GENERAL CONDITIONS OF INTERCHANGEABILITY,ISO
METRIC THREAD PROFILE AND B.N.A.E. TOLERANCES.)
NF L43-211-1973 环形接头用阳螺纹部件 (MALE PARTS FOR CYLINDRICAL
UNION.)
NF L43-212-1973 环形接头用连接螺母 (UNION NUTS FOR CYLINDRICAL
UNION.)
NF L43-213-1973 环形接头的双外螺丝接头 (DOUBLE UNIONS FOR
CYLINDRICAL UNION.)
NF L43-215-1973 环形接头（RT）.一般互换条件.ISO 米制螺纹剖面和公差
(CYLINDRICAL UNION. GENERAL CONDITIONS OF INTERCHANGEABILITY,ISO
METRIC THREAD PROFILE AND TOLERANCES.)
NF L43-310-1973 可旋转管接头（RO）.一般互换条件.ISO 米制螺纹剖面和BNAE公差
(SWIVEL CONNECTORS. GENERAL CONDITIONS OF INTERCHANGEABILITY,ISO
METRIC THREAD PROFILE AND B.N.A.E. TOLERANCES.)
NF L43-311-1973 低压旋转接头的环形部分 (SWIVEL CONNECTORS
FOR LOW PRESSURE APPLICATIONS,ANNULAR PART.)
NF L43-312-1973 低压旋转接头的空心螺栓 (SWIVEL CONNECTORS
FOR LOW PRESSURE APPLICATIONS,BANJO BOLT.)
NF L43-315-1973 旋转接头（RO）.一般互换条件.ISO 米制螺纹剖面和公差
(SWIVEL CONNECTORS. GENERAL CONDITIONS OF INTERCHANGEABILITY,ISO
METRIC THREAD PROFILE AND TOLERANCES.)
NF L43-360-2002 航空航天系列.钛合金管联接器8°30'.带螺纹的管端弯接头
(Aerospace series - Pipe coupling 8 o30' in
titanium alloy - Unions, welded, end, threaded.)
NF L43-362-2002 航空航天系列. 8°30'钛合金管连接件.直接头 (Aerospace
series - Pipe couplings 8 o30' in titanium alloy
- Unions, straight.)
NF L43-363-2002 航空航天系列. 8°30'钛合金管连接件.直减径接头 (Aerospace
series - Pipe coupling 8 o30' in titanium alloy
- Unions, straight, reducer.)
NF L43-364-2002 航空航天系列.8°30'钛合金管联接件.隔壁直角管接头
(Aerospace series - Pipe couplings 8 o30' in
titanium alloy - Unions, straight bulkhead.)
NF L43-365-2002 航空航天系列.8°30'钛合金管联接件.隔壁直角弯接头
(Aerospace series - Pipe coupling 8 o30' in
titanium alloy - Unions, bulkhead, welded end.)
NF L43-366-2002 航空航天系列.钛合金管联接器8°30'.带密封环的异径管端接头
(Aerospace series - Pipe coupling 8 o30' in
titanium alloy - Adaptors, reduced pipe end,
with lockring.)
NF L43-390-2002 航空航天系列.8°30'钛合金管联接件. 长型隔壁直通接头
(Aerospace series - Pipe coupling 8 o30' in
titanium alloy - Unions, bulkhead, long.)
NF L43-391-2002 航空航天系列.8°30'钛合金管联接件. 长型隔壁直通接头焊接端
(Aerospace series - Pipe coupling 8 o30' in
titanium alloy - Unions, bulkhead, long, welded
end.)
NF L43-396-2002 航空航天系列.钛合金管联接器8°30'.十字T形管接头
(Aerospace series - Pipe coupling 8 o30' in
titanium alloy - Unions, cross.)
NF L43-407-2002 航空航天系列.钛合金管联接器8°30'.检修用焊接端部的闷头管接头
(Aerospace series - Pipe coupling 8 o30' in
titanium alloy - Unions, bulkhead welded end,
for repair.)
NF L43-408-2002 航空航天系列.钛合金管联接器8°30'.检修用长的焊接端部的闷头管接头
(Aerospace series - Pipe coupling 8 o30' in
titanium alloy - Unions, bulkhead long welded
end, for repair.)
NF L43-409-2002 航空航天系列.钛合金管联接器8°30'.检修用焊接端加螺纹的管接头
(Aerospace series - Pipe coupling 8 o30' in
titanium alloy - Unions, welded end threaded
for repair.)
NF L43-550-1988 航空航天轮机设备.快卸低压接头.一般互换条件 (AEROSPACE.
CABIN EQUIPMENTS. LOW PRESSURE QUICK DISCONNECT
COUPLING. GENERAL CHARACTERISTICS.)
NF L43-581-1967 飞行器的液体装置.管端插入接头.(RECH.) (AIRCRAFT
FLUID INSTALLATIONS. PLUG-IN UNIONS,TUBE END.
(RECH.).)
NF L43-582-1966 飞行器液体装置.橡胶管接头.(RECH.) (AIRCRAFT
FLUID INSTALLATIONS. CONNECTORS FOR RUBBER HOSE.
(RECH.).)
NF L43-586-1972 螺钉固定光滑接头.ISO 螺纹剖面和公差 (PLUG-IN
UNIONS,TUBE END. ISO THREAD PROFILE AND TOLERANCES.)
NF L43-587-1973 橡胶管接头.ISO 米制螺纹剖面和公差 (RUBBER
HOSE CONNECTIONS. ISO METRIC THREAD PROFILE
AND TOLERANCES.)
NF L43-601-1974 带法兰的接头.连接法兰 (FLANGED CONNECTIONS
- FLANGES FOR UNIONS.)
NF L43-602-1974 带法兰的接头.凹端 (FLANGED CONNECTIONS
- INTERNAL BOSSES.)
NF L43-603-1974 带法兰的接头.环形接头 (FLANGED CONNECTIONS.
O-RINGS.)
NF L43-611-1977 不锈钢制钎接带法兰的直接头 (FLANGED STRAIGHT
UNIONS,SOLDER TYPE,STAINLESS STEEL.)
NF L43-618-2003 航空航天系列.耐热钢制37度管接头.转动螺套.英制 (Aerospace
series - Pipe coupling 37 o, in heat resisting
steel - Swivel nuts - Inch series.)
NF L43-619-2003 航空航天系列.耐热钢制37度管接头.焊接端直通接管头.英制
(Aerospace series - Pipe couplings, 37 o, spherical,
in heat resisting steel - Straight nipples,
welded end - Inch series.)
NF L43-620-2003 航空航天系列.60度钛合金管接头.油口接头 (Aerospace
series - Pipe couplings, 60 o, in titanium alloy
- Port connection.)
NF L43-621-2003 航空航天系列.60度钛合金TI-P64001球形管接头.直通转动螺套
(Aerospace series - Pipe couplings, 60 o, spherical,
in titanium alloy TI-P64001 - Swivel nuts, straight.)
NF L43-626-2003 航空航天系列.60度钛合金TI-P64001球形管接头.拉力张线用转动螺套
(Aerospace series - Pipe couplings, 60 o, spherical,
in titanium alloy TI-P64001 - Swivel nuts for
thrust wire.)
NF L43-627-2003 航空航天系列.60度钛合金TI-P64001球形管接头.焊接的90度弯头
(Aerospace series - Pipe couplings, 60 o, spherical,
in titanium alloy TI-P64001 - Elbows 90 o, welded.)
NF L43-628-2003 航空航天系列.60度钛合金TI-P64001球形管接头.钢FE-PA13制拉力张线
(Aerospace series - Pipe couplings, 60 o, spherical,
in titanium alloy TI-P64001 - Thrust wires in
steel FE-PA13.)
NF L43-629-2003 航空航天系列.耐热钢制37度球形管接头.端部焊接的90度弯管接头.英制
(Aerospace series - Pipe coupling, 37 o, spherical,
in heat resisting steel - Elbow 90 o nipples,
welded end - Inch series.)
NF L43-630-2003 航空航天系列.耐热钢制37度球形管接头.加螺纹直活管节.英制
(erospace series - Pipe coupling 37 o, spherical,
in heat resisting steel - Straight unions, threaded
- Inch series.)
NF L43-631-2003 航空航天系列.耐热钢制37度球形管接头.端部焊接的箍.英制
(Aerospace series - Pipe coupling, 37 o, spherical,
in heat resisting steel - ferrules, welded end
- Inch series.)
NF L43-632-2003 航空航天系列.耐热钢制37度管接头.管套组件.英制 (Aerospace
series - Pipe coupling, 37 o, in heat resisting
steel - Cap assemblies - Inch series.)
NF L43-633-2003 航空航天系列.耐热钢制37度球形管接头.端部焊接的三通接头.英制
(Aerospace series - Pipe coupling, 37 o, spherical,
in heat resisting steel - Tees nipples, welded
end - Inch series.)
NF L43-634-2003 航空航天系列.高达21000 kPa的37度球形管接头.英制.技术规范
(Aerospace series - Pipe coupling, 37 o, spherical,
up to 21 000 kPa - Inch series - Technical specification.)
NF L43-635-2003 航空航天系列.耐热钢制焊接管接头.90度弯头.英制 (Aerospace
series - Pipe coupling, welded, in heat resisting
steel - Elbows 90 o - Inch series.)
NF L43-636-2003 航空航天系列.耐热钢制焊接管接头.减速器.英制 (Aerospace
series - Pipe coupling, welded, in heat resisting
steel - Reductors - Inch series.)
NF L43-637-2003 航空航天系列.耐热钢制焊接管接头.三通管.英制 (Aerospace
series - Pipe coupling, welded, in heat resisting
steel - Tees - Inch series.)
NF L44-070-1979 空中加油.接头的尺寸特性和功能 (IN-FLIGHT REFUELLING
EQUIPMENT. DIMENSIONAL AND FUNCTIONAL CHARACTERISTICS
OF CONNECTIONS.)
NF L44-511-1985 飞机的地面供给.小流量接头 (Ground supply.
Low flow connection.)
NF L44-512-1973 低压接头.ISO 米制螺纹剖面和BNAE公差 (AIRCRAFT
GROUND SUPPLY. LOW PRESSURE CONNECTION. ISO
METRIC THREAD PROFILE AND B.N.A.E. TOLERANCES.
(RECH.).)
NF L44-514-1975 低压气动起动接头 (Low pressure compressed
air starting connections.)
NF L44-515-1989 航空和航天流体装置里的供氧接头 (Aerospace.
Gaseous oxygen replenishment for use in fluid
systems (old type). Dimensions (inch series).)
NF L44-516-1979 液氧流入接头 (Liquid oxygen replenishment
couplings.)
NF L44-517-1980 ISO 米制螺纹剖面和公差低压接头 (Low pressure
connections, ISO metric thread profile and tolerances.)
NF L44-518-1990 机舱地面增压试验用接头 (Aircraft. Ground
pressure testing connections for pressure cabins.
Dimensions (inch series).)
NF L44-519-1984 氧气面罩和氧气源的接头 (Joints for connecting
crew member`S regulators masks to oxygen sources.)
NF L44-520-1974 空调用２００mm接头 (200 mm air-conditioning
connections.)
NF L44-521-1974 空调用１３０mm接头 (130 mm air-conditioning
connections.)
NF L44-532-1977 飞机地面给养.加压饮用水源接头 (AIRCRAFT GROUND
SUPPLY. CONNECTIONS FOR DRINKING WATER SUPPLIED
UNDER PRESSURE.)
NF L44-540-1974 甲醇水压力供水接头.标定尺寸19mm (Water-methanol
pressure connections. Nominal dimension 19 mm.)
NF L44-541-1974 甲醇水压力供水接头.标定尺寸38mm (Water-methanol
pressure connections. Nominal dimension 38 mm.)
NF L44-550-1978 润滑油压力注入接头 (Pressure re-oiling
connection.)
NF L44-570-1980 飞机地面给养.燃料加压注入接头 (Aircraft ground
supply. Pressure refuelling connections.)
NF L44-615-1989 航空和航天.液体系统用的液态氧的.注入接头尺寸(英制)
(Aerospace. Gaseous oxygen replenishment for
use in fluid systems (new type). Dimensions
(inch series).)
NF L46-012-1986 环形接头.６４Ｃ８氧烃橡胶.精确度Ａ验.质量分类 (O-RINGS.
FLUOROCARBON RUBBER 64C8. PRECISION CLASS A.
QUALITY CLASS 3.)
NF L46-013-1986 环形接头.２１Ａ７丙烯丁二烯--晴橡胶.精确度Ａ级.质量３级
(O-RINGS. BUTADIENE ACRYLONITRILE RUBBER 21A7.
PRECISION CLASS A. QUALITY CLASS 3.)
NF L46-014-1986 环形接头.２０Ａ８丙烯丁二烯－晴橡胶.精确度Ａ级.质量３级
(O-RINGS. BUTADIENE ACRYLONITRILE RUBBER 20A8.
PRECISION CLASS A. QUALITY CLASS 3.)
NF L46-015-1987 环形接头.２０Ｂ８丙烯丁二烯- 晴橡胶.精确度Ａ级.性能３级
(O-RINGS. BUTADIENE ACRYLONITRILE RUBBER 20B8.
PRECISION CLASS A. PERFORMANCE CLASS 3.)
NF L46-016-1987 环形接头.４１Ｂ８丁烯丙烯橡胶.精确度Ａ级.性能３级 (O-RINGS.
ETHYLENE-PROPYLENE RUBBER 41B8. PRECISION CLASS
A. PERFORMANCE CLASS 3.)
NF L46-322-1980 NFL ４０- １０４和类似型式接头阳螺纹端用金属保护外壳.ISO
米制螺纹剖面和公差 (PROTECTIVE,METALLIC,CAP,FOR NF L
40-104 MALE FITTINGS AND SIMILAR TYPES. ISO
METRIC THREAD PROFILE AND TOLERANCES.)
NF L46-331-2002 航空航天系列.8°30'钛合金管接头.压合栓 (Aerospace
series - Pipe coupling 8 o30' in titanium alloy
- Pressure plugs.)
NF L46-332-2002 航空航天系列.钛合金 8°30'管接头.带动态梁密封端的单头卡套
(Aerospace series - Pipe coupling 8 o30' in
titanium alloy - Ferrules, blind, with dynamic
beam seal end.)
NF L46-334-2002 航空航天系列.8°30'管接头.螺母防护帽 (Aerospace
series - Pipe coupling 8 o30' - Protective caps.)
NF L46-335-2002 航空航天系列.8°30'接头.外螺纹防护栓 (Aerospace
series - Pipe coupling 8 o30' - Protective plugs
with external threads.)
NF L46-336-2002 航空航天系列.8°30'接头.内螺纹防护栓 (Aerospace
series - Pipe coupling 8 o30' - Protective caps
with internal threads.)
NF L48-135-1972 燃料计量器、燃料泵等接头的使用互换性（ISO 螺纹剖面和公差）
(IN-SERVICE INTERCHANGEABILITY. FLANGES FOR
LEVEL INDICATORS,FUEL PUMPS,ETC... (ISO THREAD
PROFILE AND TOLERANCES).)
NF L54-191-1988 航空器材.后部非密封的闭锁的,带塑料箱的,使用温度55℃-175℃的密封矩形电接头
(CONNECTORS,ELECTRICAL,RECTANGULAR,WITH SEALED
AND NON SEALED REAR,PLASTIC SHELL,LOCKING DEVICE
AND OPERATING TEMPERATURES. 55 DEGREES C TO
175 DEGREES C.)
NF L92-311-1966 机上起重支垫用回转接头.(RECH.) (SWIVEL
JOINTS FOR AIRCRAFT JACKING PADS. (RECH.).)
NF M82-237-1955 煤矿器材和工具.煤矿器材和工具.压缩空气管.变径管接头
(MINING EQUIPMENT. COMPRESSED AIR PIPES. CONICAL
REDUCTION COUPLINGS.)
NF M82-426-1987 煤矿器材.液压传送接头.尺寸和特性 (Coal mine
equipment. Connections for hydraulic transmissions.
Sizes and characteristics.)
NF M88-081-1974 道路油罐车.液态化学产品金属油罐.排放装置.快速接头 (ROAD
TANKERS. METAL TANKERS FOR LIQUID CHEMICAL PRODUCTS.
DISCHARGE DEVICES : QUICK-ACTION COUPLINGS.)
NF M88-768-1980 液化烃容器装置.气态物质用接头软管 (INSTALLATIONS
FOR LIQUEFIED HYDROCARBONS IN CONTAINERS. FLEXIBLE
COUPLINGS FOR GAS PHASE.)
NF M88-769-1977 商用丙烷可动容器装置.接头.自动换向装置.制造.功能.试验
(COMMERCIAL PROPANE INSTALLATIONS IN MOVABLE
CONTAINERS. AUTOMATIC COUPLER-REVERSER. CONSTRUCTION-OPERATION-TESTS.)
NF M88-770-1986 商用丁烷钢瓶装置.接头.自动换向装置.制造.功能.试验
(COMMERCIAL BUTANE INSTALLATIONS IN CYLINDERS.
AUTOMATIC CHANGEOVER. CONSTRUCTION. OPERATION.
TESTS.)
NF P12-602-2000 圬工辅助成份的试验方法.第2部分:灰浆粘结处预制床接头增强的粘结强度的测定
(Methods of test for ancillary components for
masonry - Part 2 : determination of bond strength
of prefabricated bed joint reinforcement in
mortar joints.)
NF P16-304-1997 地下排水管道用纤维水泥管.第1部分:重力循环系统用管子、接头和配件(欧洲标准EN
588-1) (Fibre-cement pipes for sewers and drains.
Part 1 : pipes, joints and fittings for gravity
systems.)
NF P16-321-1-1996 排水排污用陶管、配件和管接头.第1部分:要求(欧洲标准EN
295-1) (Vitrified clay pipes and fittings and
pipe joints for drains and sewers. Part 1 :
requirements.)
NF P16-321-4-1995 排水管和污水管用的陶土管和配件及管接头.第4部分:专用配件、转换接头和可互换附件的要求(EN
295-4) (Vitrified clay pipes and fittings and
pipe joints for drains and sewers. Part 4 :
requirements for special fittings, adaptors
and compatible accessories.)
NF P16-321-5-1994 排水及污水用陶土管道,配件和管接头.第5部分:多孔陶土管道和配件的要求(EN
295-5) (Vitrified clay pipes and fittings and
pipe joints for drains and sewers. Part 5 :
requirements for perforated vitrified clay pipes
and fittings.)
NF P16-321-6-1996 排水及污水用陶土管道.配件和管接头.第6部分:陶土管道的出入水孔的要求
(Vitrified clay pipes and fittings and pipe
joints for drains and sewers. Part 6 : requirements
for vitrified clay manholes.)
NF P16-321-7-1996 排水及污水用陶土管道.配件和管接头.第7部分:陶土管道和管道插孔用连接件的要求
(Vitrified clays pipes and fittings and pipe
joints for drains and sewers. Part 7 : requirements
for vitrified clay pipes and joints for pipe
jacking.)
NF P16-361-5-1997 无压地下排水系统用塑料管道系统.不饱和聚酯树脂(UP)基础上的玻璃增强热固塑料(GRP).第5部分:接头的适用性
(Plastics piping systems for non-pressure drainage
and sewerage. Glass-reinforced thermosetting
plastics (GRP) based on unsaturated polyester
resin (UP). Part 5 : fitness for purpose of
the joints.)
NF P21-380-2002 木结构.试验方法.机械紧固件用接头的循环试验 (Timber
structures - Test methods - Cyclic testing of
joints made with mechanical fasteners.)
NF P24-505-2000 门窗制造用未增塑聚氯乙烯型材.焊接弯头和T接头强度的测定
(Unplasticized polyvinylchloride (PVC-U) profiles
for the fabrication of windows and doors - Determination
of the strength of welded corners and T-joints.)
NF P41-302-1994 纤维水泥制品.压力管道和接头(欧洲标准EN 512) (Fibre-cement
products. Pressure pipes and joints.)
NF P41-400-1995 包括接头和配件的混凝土压力管的共同要求 (Common
requirements for concrete pressure pipes including
joints and fittings.)
NF P41-401-1995 包括接头和配件的非圆柱型加筋混凝土压力管 (Reinforced
concrete pressure pipes and distributed reinforcement
concrete pressure pipes (non-cylinder type),
including joints and fittings.)
NF P41-402-1995 包括接头和配件的圆柱型加筋混凝土压力管 (Reinforced
concrete pressure pipes, cylinder type, including
joints and fittings.)
NF P41-403-1995 包括接头和配件的圆柱型和非圆柱型预应力混凝土压力管及管用预应力钢的具体要求
(Prestressed concrete pressure pipes, cylcinder
and non-cylinder, including joints, fittings
and specific requirement for prestressing steel
for pipes.)
NF P85-210-1-2002 DTU 44.1.建筑工程.使用密封剂的密封接头面.第1部分:技术条款
(DTU 44.1 - Building works - Sealing joint front
by implementation of sealants - Part 1 : technical
clauses.)
NF P85-210-2-2002 DTU 44.1.建筑工程.个人合同.使用密封剂的密封接头面.第2部分:特殊条款
(DTU 44.1 - Building works - Private contracts
- Sealing joint front by implementation of sealants
- Part 2 : special clauses.)
NF R12-636-1998 道路车辆.液压制动系统.导管、螺纹孔、外螺纹接头和软管管端接头
(Road vehicles. Hydraulic braking systems. Simple
flare pipes, tapped holes, male fittings and
hose end fittings.)
NF R13-439-1998 道路车辆.电子线路板的成组配线装置.第1部分:单极联接接头标记.尺寸与特殊要求
(Road vehicules. Connections for on-board electrical
wiring harnesses. Part 1 : tabs for single-pole
connections. Dimensions and specific requirements.)
NF R13-702-1984 道路车辆.报警插头.接头.机械特性 (ROAD VEHICLES.
DIAGNOSTIC PLUG. CONNECTOR. MECHANICAL CHARACTERISTICS.)
NF R16-207-1955 平圆柱形接头软管 (FLEXIBLE PIPES WITH
SMOOTH CYLINDRICAL ENDS.)
NF R16-208-1955 不对称接头软管 (FLEXIBLE PIPES WITH
ASYMMETRICAL ENDS.)
NF R16-307-1988 小量操纵球形接头 (ROAD VEHICLES. KNUCKLE
JOINTS FOR SMALLE CONTROLS. DIMENSIONAL CHARACTERISTICS.)
NF R16-326-1986 道路车辆.空气滤清器接头.A型和B型.尺寸 (ROAD
VEHICLES. AIR FILTER CONNECTIONS. TYPES A AND
B. DIMENSIONS.)
NF R95-403-1970 双锥套管道接头.连接尺寸 (PIPE FITTINGS
WITH DOUBLE TAPER SLEEVES. COUPLING DIMENSIONS.)
NF R95-404-1968 锥颈双拼式管道接头 (PIPE FITTINGS IN
TWO PARTS WITH TAPERED BEARING.)
NF R95-405-1970 双锥套管道接头.插入件 (PIPE FITTINGS WITH
DOUBLE TAPER SLEEVES. INSERTS.)
NF R95-406-1975 能量储备制动系统.螺旋连接接头和弹性垫圈 (ENERGY
RESERVE BRAKE SYSTEMS. COUPLINGS WITH THREAD-CONNECTIONS
AND FLEXIBLE GASKETS.)
NF R99-021-1953 柔性接头垫圈 (RINGS FOR FLEXIBLE JOINTS.)
NF S61-704-1966 消防设备.压力输送用40和65mm自动关闭对称半接头 (FIRE
FIGHTING EQUIPMENT. SELF-SEALING SYMMETRICAL
HALF COUPLINGS,SIZES 40 AND 65.)
NF S61-705-1966 消防设备.AR型100mm自动关闭对称半接头 (FIRE
FIGHTING EQUIPMENT. SELF-SEALING SYMMETRICAL
HALF COUPLINGS,SIZE 100. TYPE AR.)
NF S61-706-1966 消防设备.GUILLEMIN型自动关闭对称接头半壳体或制动片的定位
(FIRE FIGHTING EQUIPMENT. POSITIONING OF THE
LUGS OR JAWS ON GUILLEMIN-TYPE AND SELF-SEALING
SYMMETRICAL COUPLINGS.)
NF S61-707-1973 消防设备.名义直径300救火通风用半接头 (FIRE FIGHTING
EQUIPMENT. VENTILATION. TYPE SEMI-COUPLINGS
FOR FIRE USE : DN 300.)
NF S76-024-1-2000 呼吸保护装置.气瓶阀.插入式连接器用螺纹接头 (Respiratory
protective devices - Gas cylinder valves - Part
1 : thread connections for insert connector.)
NF S76-024-2-1999 呼吸保护装置.气瓶阀.插座接头 (RESPIRATORY
PROTECTIVE DEVICES. GAS CYLINDER VALVES. PART
2 : OUTLET CONNECTIONS. (EUROPEAN STANDARD EN
144-2).)
NF S90-110-1996 便携式气瓶.医用指针指示马蹄型阀门排出口接头 (Transportable
gas cylinders. Pin-index, yoke-type valve outlet
connections for medical use.)
NF S90-425-1989 外科植入物.矫形外科用的附件接头.一般规范 (IMPLANTS
FOR SURGERY. STAPLES WITH PARALLEL LEGS FOR
ORTHOPAEDIC USE. GENERAL REQUIREMENTS.)
NF S91-313-1997 牙科设备.给排水管接头 (Dental equipment.
Connections for supply and waste lines.)
NF T47-301-1972 橡胶.管道接头用压制和模制合成橡胶垫圈和型材.材料的一般特性
(RUBBER MOLDED AND EXTRUDED SEALING RINGS AND
PROFILES FOR PIPE WORK. GENERAL SPECIFICATIONS
OF MATERIALS.)
NF T47-305-1-1996 弹性密封.排水设施用管接头密封用材料的要求.第1部分:硫化橡胶
(Elastomeric seals. Materials requirements for
pipe joint seals used in water and drainage
applications. Part 1 : vulcanized rubber.)
NF T47-305-2-2000 弹性密封件.水和排水设施用管接头密封件材料的要求.第2部分:热塑性弹性材料
(Elastomeric seals - Materials requirements
for pipe joint seals used in water and drainage
applications - Part 2 : thermoplastic elastomers.)
NF T47-305-3-2000 弹性密封件.水和排水设施用管接头密封件材料的要求.第3部分:硫化橡胶泡沫材料
(Elastomeric seals - Materials requirements
for pipe joint seals used in water and drainage
applications - Part 3 : cellular material of
vulcanized rubber.)
NF T47-305-4-2000 弹性密封件.水和排水设施用管接头密封件材料的要求.第4部分:铸造聚氨基甲酸乙酯密封元件
(Elastomeric seals - Materials requirements
for pipe joint seals used in water and drainage
applications - Part 4 : cast polyurethane sealing
elements.)
NF T54-012-1995 塑料管道系统.热塑塑料压力管道用的弹性密封环型接头和机械接头.外部液压条件下防漏密封试验方法
(PLASTICS PIPING SYSTEMS. ELASTOMERIC SEALING
RING TYPE JOINTS AND MECHANICAL JOINTS FOR THERMOPLASTICS
PRESSURE PIPING. TEST METHOD FOR LEAKTIGHTNESS
UNDER EXTERNAL HYDROSTATIC PRESSURE. (EUROPEAN
STANDARD EN 911).)
NF T54-029-1981 塑料.未增塑聚氯乙烯模制接头.压力系列.规范 (Plastics.
Moulded unplasticized PVC fittings. Pressure
series. Specifications.)
NF T54-037-1981 塑料.未增塑聚氯乙烯管道元件.生活污水无压排放设备用密封圈接头.使
用特性 (Plastics. Un-plasticized PVC parts dor
piping. Simple assemblies with sealing rings
for domestic water drainage piping. End use
test. Specification.)
NF T54-038-1981 装配有压力管用密封圈的未增塑聚氯乙烯管和接头.尺寸特性
(Unplasticized polyvinyl chloride pipes and
fittings. Assembly by sealing rings for pressure
pipelines. Dimensional caracteristics.)
NF T54-039-1988 塑料.未增塑聚氯乙烯压力管用密封圈的固定接头.使用特性.规范
(Plastics. Unplasticized polyvinyl chloride
pipes and fittings. Assembly by sealing rings
for pressure pipelines. Fitness for use.)
NF T54-041-1994 塑料管道系统.压力管道用弹性密封圈型接头的热注塑料配件.耐无轴向力短暂内压力性能的试验方法
(Plastics piping systems. Injection-moulded
thermoplastics fittings for elastic sealing
ring type joints for pressure piping. Test method
for resistance to a short-term internal pressure
without end thrust.)
NF T54-042-1994 塑料管道系统.压力管道用溶剂-水泥胶合接头的注模承窝配件
(Plastics piping systems. Injection-moulded
socket fittings for solvent-cemented joints
for pressure piping. Test method for resistance
to a short-term internal hydrostatic pressure.)
NF T54-044-1978 塑料.聚乙烯管与接头.按标定密度和热融流动指数命名的聚乙烯的名称
(POLYETHYLENE (PE) PIPES AND FITTINGS. DESIGNATION
OF POLYETHYLENE BASED ON NOMINAL DENSITY AND
MELT FLOW INDEX.)
NF T54-051-1979 聚乙烯管道.机械接头的载荷减小.试验方法与规 (Polyethylene
pipes. Pressure drop in mechanical pipe-jointing
systems. Method of test and requirements.)
NF T54-052-2001 人类饮用水输送用塑料管道系统.迁移评定.塑料管和配件及其接头迁移值的测定
(Plastics piping systems for the transport of
water intended for human consumption - Migration
assessment - Determination of migration values
of plastics pipes and fittings and their joints.)
NF T54-090-1976 塑料.未增塑聚氯乙烯和氯化聚氯乙烯管件.管和接头颜色 (PLASTICS.
UNPLASTICIZED AND CHLORINATED PVC PIPES. COLOUR
OF PIPES AND FITTINGS.)
NF T54-095-1985 塑料.未增塑聚氯乙烯管件接头粘合溶剂.使用特性 (Adhesive
with solvents for assembly of unplasticized
PVC pipe elements. Characterization. Basic test
methods.)
NF T54-905-2002 塑料管道系统.热塑性压力管用端部承载或非端部承载组件和接头.内部水压下长期无漏损的试验方法
(Plastics piping systems - End-load-bearing
and non-end-load-bearing assemblies and joints
for thermoplastics pressure piping - Test method
for long-term leaktightness under internal water
pressure.)
NF T54-906-1996 塑料管道系统.埋置非压管道设备用热塑管道系统.弹性密封环型接头耐泄漏性试验方法
(Plastics piping systems. Thermoplastics piping
systems for buried non-pressure applications.
Test methods for leaktightness of elastomeric
sealing ring type joints.)
NF T54-923-2000 塑料管道系统.与未增塑聚氯乙烯管一起使用的未增塑聚氯乙烯弹性密封环式套筒接头.负压下密封试验法
(Plastics piping systems - Elastomeric-sealing-ring-type
socket joints of unplasticized poly(vinyl chloride)
(PVC-U) for use with PVC-U pipes - Test method
for leaktightness under negative pressure.)
NF T54-926-2000 热塑性管道系统.地下常压排污设施用接头.用密封压力评定法测定带热塑性弹性体(TPE)密封件接头的长期密封性
(Thermoplastics piping systems - Joints for
buried non-pressure sewage applications - Test
method for long-term sealing performance of
joints with thermoplastic elastomer (TPE) seals
by estimating the)
NF T54-937-2000 塑料管道系统.与未增塑聚氯乙烯管一起使用的弹性密封环式套筒接头.内压下角度偏转密封试验法
(Plastics piping systems - Elastomeric-sealing-ring-type
socket joints for use with unplasticized poly(vinyl
chloride) (PVC-U) pipes - Test method for leaktightness
under internal pressure and with ang)
NF T57-214-5-1996 压力下地下排水系统用塑料管道系统.不饱和聚酯树脂基玻璃增强热固塑料.第5部分:接头的适用性
(Plastics piping systems for underground drainage
and sewerage under pressure. Glass-reinforced
thermosetting plastics (grp) based on unsatured
polyester resin (up). Part 5: fitness for purpose
of the joints.)
NF T57-215-1996 塑料管道系统.玻璃增强热固性塑料管和配件接头.挠性和铰链接头耐泄漏和损伤试验方法
(Plastics piping systems. Joints for glass-reinforced
thermosetting plastics (grp) pipes and fittings.
Test methods for leaktightness and resistance
to damage of flexible and reduced-articulation
joints.)
NF T57-224-1997 塑料管道系统.玻璃纤维增强热固性塑料(GRP)构件.检验带有弹性密封件的刚性锁定的管套筒接头设计的试验方法
(Plastics piping systems. Glass-reinforced thermosetting
plastics (GRP) components. Test methods to prove
the design of rigid locked socket-and-spigot
joints with elastomeric seals.)
NF T57-225-1997 塑料管道系统.玻璃纤维增强热固性塑料元件.验证胶合管套筒接头设计的测试方法
(Plastics piping systems. Glass-reinforced thermosetting
plastics (GRP) components. Test methods to prove
the design of cemented socket-and-spigot joints.)
NF T76-119-2003 胶粘剂.非结构应用中的木材胶粘剂.搭接接头的抗拉伸剪切强度的测定
(Adhesives - Wood adhesives for non-structural
applications - Determination of tensile shear
strength of lap joints.)
NF T81-101-1975 液态化学制品和带1６型旋转同步额定压力的烃类对称半接头(吉尔曼体系)(ＧＵＩＬＬＥＭＩＮ)的运输和装卸
(TRANSPORT AND HANDLING OF LIQUID CHEMICAL PRODUCTS
AND HYDROCARBONS-HALF SYMETRIC COUPLING(GUILLEMIN
SYSTEM)WITH ROTATING LOCK-NOMINALPRESSURE 16.)
NF T81-106-1976 喷雾状产品的运输.最大压力２．５bar气动排空的道路罐车.接头
(TRANSPORTATION OF POWDERY PRODUCTS. ROAD TANKERS
WITH PNEUMATIC DISCHARGE UNDER MAXIMUM PRESSURE
2.5 BAR. COUPLING.)
NF T81-125-1987 冷冻液化气容器.沉淀分离器.Ｎ2 Ｏ或冷冻液ＣＯ2 的接头
(REFRIGERATED LIQUEFIED GAS CONTAINERS. TRANSFER
DEVICES. COUPLINGS FOR REFRIGERATED N2O OR CO2.)
NF T81-126-1987 冷冻液化气容器.沉淀分离器.冷冻液态氧或氮的ＤＮ４０接头
(REFRIGERATED LIQUEFIED GAS CONTAINERS. TRANSFER
DEVICES. DN 40 COUPLINGS FOR REFRIGERATED O2
OR N2.)
NF U14-406-1992 农业拖拉机和机械.通用快速动作液压接头 (Agricultural
trators and machinery. General purpose quick-action
hydraulic couplers.)
NF Z85-506-1-2002 模拟和综合业务数字网(ISDN)用户线路的电路试验用局域交换Q3接口.第1部分:Q3接头规范
(Q3 interface exchange at the Local Exchange
(LE) for line and circuit testing of analogue
and Integrated Services Digital Network (ISDN)
suscriber lines - Part 1 : Q3 interface specification.)
XP P98-090-1999 与膨胀节有关的试验.沥青插塞接头的永久变形.轮辙试验 (Tests
relating to expansion joints - Asphalt plug
joint permanent deformation - Wheel tracking
test.)
|
管件知识
